Chapter 7, TL1 Alarms and Errors

This chapter provides TL1 alarm and error information supported by the Cisco ONS 15454 and Cisco ONS 15327, including:

Each alarm includes a description and severity. Errors are listed by error type and command and include error type and error message. For a list of TL1 conditions, see Table 4-54.

7.1 Alarms

Refer to "Alarm Troubleshooting" in the Cisco ONS 15454 Troubleshooting Guide and in the Cisco ONS 15327 User Documentation for complete alarm definitions, trouble notifications, and fault recovery procedures. The alarms are listed alphabetically by alarmable object:

For a sample of each TL1 alarm that can be generated by the ONS 15454, refer to the file 15454_r340_tl1_alarms.txt on the Cisco ONS 15454 Software CD in the subdirectory \Tl1. For a sample of each TL1 alarm that can be generated by the ONS 15327, refer to the file 15327_r340_tl1_alarms.txt on the Cisco ONS 15327 Software CD in the subdirectory \Tl1. These files can be used to test an operations support system's ability to receive alarms which the ONS 15454/ONS 15327 can raise.

• AIP	• FAN
• BITS	• HDGE (G1000)
• BPLANE	• NE
• DS1	• NESYNCH
• DS3	• OCN
• ECN	• STSMON
• ENV	• STSTERM
• EQPT	• VT-MON
• ETHER	• VT-TERM
• EXTSYNCH

7.1.1 AIP

Table 7-1 AIP
AIP Alarm	Severity (Active)	Description
INVMACADR	MJ/NSA	The ONS 15454/15327 media access control layer address (MAC address) is invalid.
MEA	CR/SA	The mismatch between entity/equipment type and provisioned attributes alarm occurs when the physical card inserted in a slot does not match the card type that is provisioned for that slot in the CTC.
MFGMEM	CR/SA	The manufacturing data memory failure alarm means that the ONS 15454/15327 cannot access the data on the erasable programmable read-only memory (EPROM).

7.1.2 BITS

Table 7-2 BITS
BITS Alarm	Severity (Active)	Description
LOF	MJ/SA	A port on the TCC/MIC BITS input detects a loss of frame (LOF) on the incoming BITS timing reference signal.
LOS	MJ/SA	The TCC/MIC card has a loss of signal (LOS) condition from the BITS timing source.
SSM-FAIL	MN/NSA	Synchronization status messaging failed.

7.1.3 BPLANE

Table 7-3 BPLANE
BPLANE Alarm	Severity (Active)	Description
MEA	CR/SA	The Mismatch Of Equipment and Attributes (MEA) alarm for the backplane means that the revision of the backplane is incompatible with XC10G equipment.
MFGMEM	CR/SA	The manufacturing data memory failure alarm means that the ONS 15454/15327 cannot access the data on the erasable programmable read-only memory (EPROM).

7.1.4 DS1

7.1.5 DS3

7.1.6 ECN

Table 7-4 DS1
DS1 Alarm	Severity (Active)	Description
LOF	MJ/SA	The receiving ONS 15454/15327 has lost frame delineation in the incoming data.
LOS	MJ/SA	A loss of signal (LOS) at the card for either a DS-3 port or a DS-1 port.
RCVR-MISS	MJ/SA	The facility termination equipment detects a missing receive cable on the DS-1 port or a possible mismatch of backplane equipment.
TRMT	MJ/SA	There is a transmission failure on the DS-1 card due to an internal hardware failure.
TRMT-MISS	MJ/SA	The facility termination equipment detects a missing transmit cable on the DS-1 port or a possible mismatch of backplane equipment.

Table 7-5 DS3
DS3 Alarm	Severity (Active)	Description
LOF	CR/SA	The receiving ONS 1545415327 has lost frame delineation in the incoming data.
LOS	CR/SA	Loss of signal at the card for either a DS-3 port or a DS-1 port.

Table 7-6 ECN
ECN Alarm	Severity (Active)	Description
LOF (EC1-12)	CR/SA	The receiving ONS 15454 has lost frame delineation in the incoming data.
LOS (EC1-12)	CR/SA	A port on the reporting EC-1 card has a loss of signal condition. A SONET receiver detects an all-zero pattern for 10 microseconds or longer.

7.1.7 ENV

7.1.8 EQPT

A card in any of the card slots. This object is used for alarms that refer to the card itself and all other objects on the card including ports, lines, STS and VT.

Table 7-7 ENV
ENV Alarm	Severity (Active)	Description
EXT	MN/NSA	A facility alarm is detected external to the node because an environmental alarm is present.

Table 7-8 EQPT
EQPT Alarm	Severity (Active)	Description
AUTORESET	MN/NSA	The card is performing a warm reboot automatically.
BKUPMEMP	CR/NSA	A problem with the TCC/XTC card's flash memory.
CARLOSS	MN/NSA	The Ethernet card has lost its link and is not receiving any signal, even an invalid one.
COMIOXC	CR/SA	The IO Slot To XCON Communication Failure alarm is raised by the XC card. It occurs when there is a communication failure for a particular IO slot.
CONTBUS-A-18	MJ/NSA	The main processor on the TCC/XTC card in Slot 7/Slot 5 has lost communication with the coprocessor on the second TCC/XTC card in Slot 11/Slot 6.
CONTBUS-A	MJ/NSA	The TCC/XTC card in Slot 7/Slot 5 has lost communication with a line card.
CONTBUS-B-18	MJ/NSA	The main processor on the TCC/XTC card in Slot 11/Slot 6 has lost communication with the coprocessor on the TCC/XTC card in Slot 7/Slot 5.
CONTBUS-B	MJ/NSA	The TCC/XTC card in Slot 11/Slot 6 has lost communication with a line card.
CTNEQPT-PBPROT	CR/SA	A failure of the main payload between the protect cross-connect (XC/XCVT/XC10G) card in Slot 10, or the protect XTC card, and the reporting traffic card.
CTNEQPT-PBWORK	CR/SA	The main payload bus between the active cross-connect (XC/XCVT/XC10G) card in Slot 8, or the active XTC card, and the reporting traffic card.
EQPT	CR/SA	A hardware failure occurred on the reporting card.
EXCCOL	MN/NSA	There are too many collisions are occurring on the network management LAN.
HITEMP	MN/NSA	The temperature of the ONS 15454/ONS 15327 is above 50 degrees Celsius.
IMPROPRMVL	CR/SA	A card was physically removed from its slot before the card was deleted in CTC.
MEA	CR/SA	The mismatch between entity/equipment type and provisioned attributes alarm occurs when the physical card inserted in a slot does not match the card type that is provisioned for that slot in the CTC.
MEM-GONE	MJ/NSA	Data generated by software operations exceeds the memory capacity of the TCC/XTC card.
MEM-LOW	MN/NSA	Data generated by software operations is close to exceeding the memory capacity of the TCC/XTC card.
PEER- NORESPONSE	MJ/NSA	The switch agent raises a Peer Card Not Responding alarm if either I/O card in a protection group does not receive a response to the peer status request message.
PROTNA	MN/NSA	The Protection Unit Not Available is raised by an out-of-service protection when a card or port that is provisioned as part of a protection group is not available.
SFTWDOWN-FAIL	MN/NSA	The software download from the TCC/XTC card to the ONS 15454 failed.
SNTP-HOST	MN/NSA	An ONS node serving as an IP proxy for the other ONS nodes in the ring is not forwarding SNTP information to the other ONS nodes in the network.
SWMTXMOD	CR/SA	Traffic on the reporting card is lost when this failure occurs.

7.1.9 ETHER

Table 7-9 EHTER
EHTER Alarm	Severity (Active)	Description
CARLOSS	MJ/SA	A Carrier Loss on the LAN alarm occurs when the ONS 15454 and the workstation hosting CTC do not have a TCP/IP connection.

7.1.10 EXTSYNCH

Table 7-10 EXTSYNCH
EXTSYNCH Alarm	Severity (Active)	Description
SYNCPRI	MN/NSA	A loss of the primary timing source (reference 1).
SYNCSEC	MN/NSA	A loss of the secondary timing source (reference 2).
SYNCTHIRD	MN/NSA	A loss of the third timing source (reference 3).

7.1.11 FAN

Table 7-11 FAN
FAN Alarm	Severity (Active)	Description
EQPT-MISS	CR/SA	Indicates the replaceable fan tray assembly unit is missing or not fully inserted.
FAN	CR/SA	A problem with the fan-tray assembly.
FANDEGRADE	MJ/NSA	The Partial Fan Failure alarm is raised if fan speed in shelf fan tray 1, 2, or 3 falls below 500 RPM when read by a tachometry counter.
MEA	CR/SA	The mismatch between entity/equipment type and provisioned attributes alarm occurs when the physical card inserted in a slot does not match the card type that is provisioned for that slot in the CTC.
MFGMEM	CR/SA	The manufacturing data memory failure alarm means that the ONS 15454/ONS 15327cannot access the data on the erasable programmable read-only memory (EPROM).

7.1.12 HDGE (G1000)

Table 7-12 HDGE (G1000)
NE Alarm	Severity (Active)	Description
CARLOSS	MJ/SA	A carrier loss on the LAN is the data equivalent of a SONET LOS alarm. The Ethernet card has lost its link and is not receiving a valid signal.
TPTFAIL	MJ/SA	Indicates a break in the end-to-end Ethernet link integrity feature of the G1000-4 cards. This alarm indicates a far-end condition and not a problem with the port reporting TPTFAIL.
UNEQ-P	CR/SA	A Signal Label Mismatch Failure Unequipped Path alarm occurs when the path does not have a valid sender. The UNEQ-P indicator is carried in the C2 signal path byte in the SONET overhead.

7.1.13 NE

Table 7-13 NE
NE Alarm	Severity (Active)	Description
DATAFLT	MN/NSA	The database exceeded the capacity of the flash memory on the TCC/XTC.
EHIBATVG-A	MJ/SA	The voltage level on battery lead A exceeds -56.7 Vdc. (ONS 15454)
EHIBATVG-B	MJ/SA	The voltage level on battery lead B exceeds -56.7 Vdc. (ONS 15454)
ELWBATVG-A	MJ/SA	The voltage on battery feed A is extremely low or has been lost, and power redundancy is no longer guaranteed. (ONS 15454)
ELWBATVG-B	MJ/SA	The voltage on battery feed B is extremely low or has been lost, and power redundancy is no longer guaranteed. (ONS 15454)
HITEMP	CR/SA	The temperature of the ONS 15454/ONS 15327 is above 50 degrees Celsius (122 degrees Fahrenheit).
PRC-DUPID	MJ/SA	Two identical node IDs exist in the same ring.
PWR-A	MJ/SA	This alarm applies to the NE rack. It is raised when there is no power supplied to the main power connector or if power is connected to the backup power connector (Connector B) but not to Connector A. (ONS 15454)
PWR-B	MJ/SA	This alarm applies to the NE rack. It is raised when there is no power supplied to the backup power connector or if power is connected to the main power connector (Connector A) but not to Connector B. (ONS 15454)
RING-MISMATCH	MJ/SA	The Ring ID of the ONS 15454/ONS 15327that is reporting the alarm does not match the Ring ID of another ONS node in the BLSR.
SNTP-HOST	MN/NSA	The SNTP (Simple Network Timing Protocol) host failure alarm indicates that an ONS node serving as an IP proxy for the other ONS nodes in the ring is not forwarding SNTP information to the other ONS nodes in the network.
SYSBOOT	MJ/SA	New software is booting on the TCC/XTC card.

7.1.14 NERING

Table 7-14 NERING
NERING Alarm	Severity (Active)	Description
BLSROSYNC	MJ/SA	The BLSR Out Of Sync alarm occurs when the mapping table needs updating.
PRC-DUPID	MJ/SA	The Procedural Error Duplicate Node ID alarm indicates that two identical node IDs exist in the same ring. The ONS 15454/ONS 15327 requires each node in the ring to have a unique node ID.
RING-MISMATCH	MJ/SA	A Procedural Error Mismatch Ring alarm occurs when the ring ID of the ONS 15454 that is reporting the alarm does not match the ring ID of another ONS node in the BLSR

7.1.15 NESYNCH

7.1.16 OCN

7.1.17 STSMON

7.1.18 STSTERM

Table 7-15 NESYNCH
NESYNCH Alarm	Severity (Active)	Description
FRNGSYNC	MJ/SA	The reporting ONS 15454/ONS 15327 is in free run synchronization mode.
FSTSYNC	MN/NSA	A fast start synchronization. The ONS 15454/ ONS 15327 is choosing a new timing reference.
HLDOVRSYNC	MJ/SA	A loss of primary/secondary timing reference.
SYNCPRI	MN/NSA	A loss of the primary timing source (reference 1).
SYNCSEC	MN/NSA	A loss of the secondary timing source (reference 2).
SYNCTHIRD	MN/NSA	A loss of the third timing source (reference 3).

Table 7-16 OCN
OCN Alarm	Severity (Active)	Description
APSB	MN/NSA	The line terminating equipment detects protection switching byte failure in the incoming automatic protection switching (APS) signal if an inconsistent APS byte or invalid code is detected.
APSCDFLTK	MN/NSA	A BLSR is not properly configured.
APSC-IMP	MN/NSA	Invalid K bytes.
APSCINCON	MN/SA	The SONET overhead contains K1/K2 APS bytes that notify receiving equipment, such as the ONS 15454/ONS 15327, to switch the SONET signal from a working to a protect path.
APSCM	MJ/SA	The ONS 15454/ONS 15327 expects a working channel but receives a protection channel.
APSCNMIS	MJ/SA	The node ID contained in the K2 byte of the APS channel being received is not present in the ring map.
APSMM	MN/NSA	There is a mismatch of the protection switching schemes at the two ends of the span.
AUTOLSROFF	CR/SA	The OC-192 card temperature exceeds 90 degrees Centigrade. The internal equipment automatically shuts down the OC-192 laser when the card temperature rises to prevent the card from self-destructing.(ONS 15454)
EOC	MJ/NSA	The ONS 15454/ONS 15327 has lost its data communications channel (DCC).
E-W-MISMATCH	MJ/SA	Nodes in a ring have an east slot/port misconnected to another east slot/port or a west slot/port misconnected to another west slot/port.
FEPRLF	MN/NSA	An automatic protection switching channel failure on a signal coming into the node.
LOF	CR/SA	A port on the reporting OC-N card has an LOF condition.
LOS	CR/SA	A port on the reporting OC-N card has a LOS condition.
SSM-FAIL	MN/NSA	Synchronization status messaging received by the ONS 15454/ONS 15327 failed

Table 7-17 STSMON
STSMON Alarm	Severity (Active)	Description
CONCAT	CR/SA	The transmitted STSc circuit is smaller than the provisioned STSc causing a mismatch of the circuit type on the concatenation facility.
LOP-P	CR/SA	A loss of pointer (LOP) condition at the path level.
PLM-P	CR/SA	A signal label mismatch failure (SLMF).
TIM-P	MN/SA	The expected path trace string does not match the received path trace string.
UNEQ-P	CR/SA	The path does not have a valid sender.

Table 7-18 STSTERM
STSTERM Alarm	Severity (Active)	Description
LOP-P	CR/SA	A loss of pointer (LOP) condition at the path level.
PLM-P	CR/SA	A signal label mismatch failure (SLMF).
TIM-P	MN/SA	The expected path trace string does not match the received path trace string. Path trace mode can be set to auto or manual for this alarm to occur.
UNEQ-P	CR/SA	The path does not have a valid sender.

7.1.19 VT-MON

Table 7-19 VT-MON
VT-MON Alarm	Severity (Active)	Description
AUTOSW-LOP	MN/SA	Automatic UPSR protection switching took place because of an LOP alarm.
AUTOSW- UNEQ	MN/SA	Automatic UPSR protection switching took place because of an UNEQ alarm.
LOP-V	MJ/SA	A loss of pointer at the VT level.
UNEQ-V	MJ/SA	The node is receiving SONET path overhead with bits 5, 6 and 7 of the V5 overhead byte all set to zeroes. The failure has occurred at the VT layer.

7.1.20 VT-TERM

Table 7-20 VT-TERM
VT-TERM Alarm	Severity (Active)	Description
LOP-V	MJ/SA	A loss of pointer at the VT level.
PLM-V	MN/SA	The content of the V5 byte in the SONET overhead is inconsistent or invalid.
UNEQ-V	MJ/SA	The node is receiving SONET path overhead with bits 5, 6 and 7 of the V5 overhead byte all set to zeroes. The failure has occurred at the VT layer.

7.2 Errors

Errors may be generated by any command or command response message. You can find errors listed by error code in Table 7-21 and listed by command in Table 7-22. The format of an error message is as follows:

7.2.1 Errors Listed by Error Code

7.2.2 Errors Listed by Command

Table 7-21 Errors Listed by Error Code
Error Code	Error Message
ENEQ	Control Not Provisioned Environmental Control Interface Not Found Equipment Not Found Equipment Not Provisioned Internal Communication Error Sensor Interface Not Found
IBEX	Invalid AID Block. Extra Datablock Invalid Payload Block. Extra Datablock Invalid Payload Block. Extra Parameters
ICNV	Equipment Does Not Match Request Equipment In Use Invalid Command Operation not supported by this card Performance Monitoring Type Not Supported
IDMS	Missing Internal Data
IDNC	Invalid Data Invalid PST Value Invalid SST Value Primary Source Cannot be Internal When Secondary Source Is Not Internal Primary Source Cannot be Internal When Third Source Is Not Internal Secondary Source Cannot be Internal When Third Source Is Not Internal
IDNV	2F-BLSR Architecture Does Not Permit Manual/Forced Span Switching At least an XC10G XC card is needed for this equipment type Cannot Change Protection Type Command Not Valid On Protect Card Facility Loopback Not Supported Frame Format Not Supported On Equipment Frame Format Contains Invalid Data Incompatible Protect Slot For Protection Incompatible Equipment Type Incompatible Equipment Type For Protection Invalid Data For 2F-BLSR Invalid Ethernet Frame Size Invalid Equipment Type Invalid Log Name Invalid MONLEV Value Invalid MONTYPE Value Invalid Protection Group Card Slot Identifier Invalid Protid Invalid Reference Invalid TAP Number Invalid Time/Date Interval Line Code Not Supported Multiple AIDs Not Allowed Multiple Protection Group Card Slot Identifiers Not Allowed Multiple References Not Allowed Protect Card Does Not Support Protection Type Protect Slot Not Provisioned Protection Group Card Slot Identifier Field Required Protection Group Does Not Exist Ring Lockout BLSR Switching Is Not Supported Switch Type Is Not Allowed On 1+1
IDRG	Difference Value Range Error Invalid PJMON Value Invalid Threshold Value
IIAC	AID Validation Failed ALL, Ranging and Grouping Are Not Supported Cannot Access 1+1 Protect Line Cannot Make Changes To Protect Card Equipment Does Not Match Request Expected Trace Not Supported On This Card Type Expected Trace String Exceeds Maximum Length (62) Incoming Trace Not Supported On This Card Type Incorrect Card Type Input, Invalid Access Invalid AID Invalid AID Pair Invalid DS1 AID Invalid Facility AID Invalid From AID Invalid G1000 Facility Port Invalid Month Or Day Invalid Operation On Drop AID Invalid PJMON Value Invalid Protect AID Invalid Protect AID Or Working AID Invalid Protect Switching Operation Invalid Reference Invalid TAP Invalid Time Invalid To AID Invalid Year List AID Not Allowed For ALL AID List Or All AID Not Supported Multiple AIDs Not Supported Multiple TAP AIDs Not Supported Not Allowed On 1+1 Protect Line Not Allowed On BLSR Protect Line Only CCT=2WAY Is Allowed When A G1000-4 Port Is Used Optional AIDs Are Not Supported RingId Does Not Match with AID Number Trace Mode Not Supported On This Card Type Trace Not Supported On This Card Type Trace String Exceeds Maximum Length (62) UPSR Cross-Connections Are Not Allowed When A G1000 Port Is Used
IICM	Input, Invalid MOD1 Input, Invalid VERB
IICT	Invalid Correlation Tag
IIDT	Cannot Activate To Older Software Cannot Revert From R2 To R1 Command Already In Progress Duplicate Performance Monitoring Schedule Flash Manager Not Active Hostname Missing In FTP URL Invalid Command Mode Value Invalid Data Parameter Invalid Location Value Invalid Revertive Time Invalid Software Switch Type Invalid State Value Mandatory FTP URL Not Provided Maximum Performance Monitoring Schedule Limit Reached Memory Out of Range Null Outputs In FTP URL Parsing Only NORM CMD_MODE Is Supported Only OOS PST Is Supported Only SWDL Is Supported For The xfertype Argument Package Name Missing in FTP URL Password Missing In FTP URL Performance Monitoring Schedule Does Not Exist Software Activate/Revert Failed Software Not Available For Switch Unknown Error Processing FTP URL Username Missing In FTP URL ftp:// Missing In FTP URL
IIFM	Invalid Payload Block. Invalid Data Format
IISP	Input, Garbage
IITA	Input, Invalid Target Identifier
INUP	External Ring ID Configuration Not Supported General Block Unsupported Node ID Configuration Not Supported RNGWTR Configuration Not Supported Ring ID Configuration Not Supported Ring Map Auto Configuration Not Supported
IPEX	Invalid Payload Block. Extra Parameters
IPMS	Invalid AID Block. Missing Mandatory Field Invalid Payload Block. Missing Mandatory Field
IPNC	Cannot Change Existing Protection Type Description Cannot Have More Than 64 Characters Invalid Flow Control Value Invalid Maximum Frame Size Invalid Parameter Invalid Primary State Parameters Are Not Consistent Parameters Not Compatible
IPNV	AID Or Condition Must Be Specified Cannot Set Expected Path Trace In Auto Mode Cross-Connection Does Not Have UPSR Path Selector Invalid Switch Type Exercise Is Not Allowed On Protected Facility Far End Performance Monitoring Values Not Supported INT Not Valid For BITS-OUT Internal-Ip Lookup Failed Internal-Network Nodes Lookup Failed Invalid Clock Source Invalid Default Router Address Invalid IIOP Port number Invalid IP Address Invalid Parameter Invalid IP Configuration Parameter Invalid IP Configuration, Subnets Differ Invalid IP Mask Invalid Parameter Invalid Payload Block. Empty Parameter Invalid SNTP Host Address Invalid Switch Command For Synchronization Invalid Switch Type New Source Must Be Specified Node Name Exceeds Maximum Length (62) PM Not Supported Primary Reference Incompatible With Timing Mode Reference Type Not Supported SPNWTR Parameter Not Supported TMGREF Parameter Not Supported Third Reference Incompatible With Timing Mode Timing Mode Not Compatible
PICC	AID Required Invalid User Access Privilege Value Invalid User Identifier-Must Conform To TL1 Rules Invalid User Password-Must Conform To TL1 Rules Logout failed New Password Same As Old Password Unknown CORBA Exception (Internal Error) Unknown User User Access Privilege Required User Already Exists User Identifier Exceeds Maximum Length Allowed User Not Authorized User Password and User Identifier Cannot Be Identical User Password Required
PIMA	Memory Out Of Range
PIUC	Cannot Delete The Logged In User Login Failed User Currently Logged Into Another Session User Is Not Superuser User Not Allowed To Change User Access Privilege User Not Allowed To Change User Password
RRNG	Invalid Slot Number
RTBY	Connection In Service TAP Already In Use TAP Number In Use
RTEN	Cannot Access VT Cannot Change Access Mode Cannot Set Access Mode Invalid Access Mode Invalid TAP AID Invalid TAP Mode Invalid TAP Number Requested TAP Does Not Exist TAP Not Found
SAAL	Already Allowed
SAAS	Equipment Already Provisioned Equipment Not Supported
SADC	TAP Not Connected
SAIN	Already Inhibited
SAIS	Port Already In Service
SAMS	Already In Clear Maintenance State Already In Force Maintenance State Already In Lockout Maintenance State Already In Manual Maintenance State
SAOP	Control Already Operated Control Not Operated Or Already Released
SAOS	Port Already In OOS-AINS Port Already In OOS-MT Port Already Out Of Service
SCAT	STS Is Already Connected Test Access Busy VT In Use VT Is Already Connected
SDBE	AID Parser Failed Cannot Access Conditions Cannot Access Controls Cannot Access Date/Time Cannot Access Defaults Description Cannot Access Environmental Settings Cannot Access Equipment Cannot Access Facility Cannot Access IP Configuration Cannot Access Interface Cannot Access Node ID Cannot Access Object Cannot Access Orderwire Cannot Access Protection Group Cannot Access Protection State Cannot Access SNTP Host Cannot Access STS Cannot Access Software Version Cannot Access Synchronization Configuration Cannot Access Timezone Cannot Access VT Cannot Access VT Performance Monitoring Parameters Cannot Create 1+1 Protection Group Cannot Edit STS Cannot Get Line Information Cannot Get Synchronization Configuration Cannot Set Date Cannot Set Date When Using SNTP Cannot Set IP Configuration Cannot Set Node Name Cannot Set Pointer Justification Monitoring Parameter (PJMON) Cannot Set SNTP Host Configuration Cannot Set Timezone Cannot Switch To E2 Byte With Express Orderwire IS Card Type Not Supported Delete Protection Group Failed Equipment Not Found Facility Does Not Exist Facility Does Not Match Request Facility Is Not Provisioned File Transfer In Progress Incompatible Parameter Values Incorrect Facility Type Internal Access Failed Internal Database Error Invalid DCC Invalid Performance Monitoring Mode Invalid Protection Group

SDBE (continued)	Location Value Invalid Object Not Provisioned Operation Not Supported On EC1 Interface STS Not Provisioned Synchronization Configuration Not Available Synchronization Status Messaging (SSM) Not Supported On EC1 Interface Used Frame Format Does Not Support Synchronization Status Messaging (SSM) VT Not Provisioned
SDLD	Duplex Unit Locked
SDNA	Standby TCC Not Ready
SNCC	Replace This Message When A SNCC message is needed
SNCN	Bad Quality Of Clock Source Cannot Switch To Inferior Reference Source Clock Source Failed Command Not Implemented Cross-Connection Type Not Supported In TL1 Invalid Clock Source STS Rate Changing Not Supported This Direction Is Not Supported
SNNS	Reference Not From Optical Card
SNPR	Cannot Get Role Of Port
SNVS	Already Switched To Internal Reference Source BLSR East Operation Already Set BLSR West Operation Already Set Cannot Manually Switch To Active Timing Source Cannot Operate Loopback In Current State Facility Not Part Of BLSR Invalid Admin State Invalid AINS Soak Time Invalid BLSR Element Invalid Clock Source Invalid Equipment State Loopback Already In Progress Loopback Not In Progress No Switch In Progress Protection Group Does Not Exist Protection Unit Active Working Unit Already Active Working Unit Already Standby
SOSE	Unrecognized Message Type
SPFA	Cannot Get Current Card Status Protection Unit Failed Or Missing
SPLD	Cannot Create 1+1 Protection Group Cannot Delete Equipment Equipment In Use Facility Is Busy Protection Unit Locked
SRCN	Already In Requested Mode Requested Condition Already Exists
SROF	1+1 Protection Group Not Found Alarm Log Empty All DCCs In Use Cannot Access 1+1 Line Cannot Access 1+1 Protected Line Cannot Access 2 Fiber BLSR Cannot Access 4 Fiber BLSR East Protection Cannot Access 4 Fiber BLSR West Protection Cannot Access 4F BLSR Cannot Access Alarm Log Cannot Access BLSR Cannot Access BLSR 2 Wire Line Cannot Access Cross-Connection Cannot Access DCC Cannot Access Facility Cannot Access Performance Monitoring Mode Cannot Access Performance Monitoring Statistics Cannot Access Protected Equipment Cannot Access Protection Group Cannot Access Protection Group Information Cannot Access Protection Group Name Cannot Access Protection Group Reversion Information Cannot Access STS Cannot Access TAP Cannot Access Unprotected Line Cannot Access VT Cannot Change XTC Protection Group Cannot Create Cross-Connection Between Incompatible Interfaces Cannot Create Protection Group Cannot Create TAP Cannot Delete Cross-Connection Cannot Delete Protected Equipment Cannot Delete Protection Group Cannot Edit STS Cannot Modify Protect Card Cannot Perform ACO Cannot Provision Equipment Cannot Provision Protection Equipment Cannot Set Bidirectional Protection Group Cannot Set Protection Group Cannot Set Protection Group Name Cannot Set Protection Group Revertive Behavior
SROF (continued)	Cannot Set Revertive Time In Non-revertive Mode Cannot Set Span Revertive Mode Unless 4-Fiber Ring Cannot Set Span Revertive Time In Non-revertive Mode Cannot Set Span Revertive Time Unless 4-Fiber Ring Cannot Switch For Specified Connection Type Cannot Switch For Specified Path Cannot Update Synchronization Reference List Command Not Supported Cross-Connection Creation Failed DCC Not In Use Date Or Time Required Element Not Found Equipment Does Not Match Request Equipment Type Not Supported Facility Not Provisioned Generation1 Does Not Support Given Quality Of RES Get IOR Failed Host Not In IP Address Format Incompatible Cross-Connection Width Insufficient Bandwidth Insufficient Path Width For Cross-connection Insufficient Path Width For Test Access Internal Exercise Failure Internal Facility Type Failure Invalid Control Type (CONTTYPE) For AID Invalid Cross-Connection Path Invalid FTP Username/Password Invalid Loopback Provision Invalid Operation For Connection Type Invalid Operation For Specified Path Invalid Path Invalid Protection Group Invalid Protection Switch Operation Invalid State When Loopback Present Invalid Synchronization Source Invalid UPSR Path Loopback Type Does Not Match MIC Cards Cannot Be Reset Maximum User Limit Reached Node::General Not Available Operate Alarm Cutoff Failed Operation Not Supported OspfTopology::OSPFTopo Not Available Package File Not Found Path Already In Use Path Specified Is Not Valid Pool Does Not Exist Protect Card Busy Requested Operation Failed Ring Reversion Failed
SROF (continued)	STS Does Not Exist STS Does Not Have TAP STS Is Already In Use STS Path Width Does Not Match STS Rates Do Not Match Security::General Not Available Software Activation Failed Software Reversion Failed Span Reversion Failed Specified Operation Is Not Valid Test Access Active UPSR Must Exist In Order To Change Revertive Behavior Unsupported Command Type Unsupported Element Type VT Does Not Exist VT Does Not Have TAP VT Not Found XC Card Does Not Support VT Cross-Connection
SRQN	BLSR Creation Failed BLSR Deletion Failed BLSR Does Not Exist BLSR Not Found Cannot Edit SENDDUS On Protect Port Cannot Edit SYNCMSG On Protect Port DCC Not Allowed On Protect Port Data Access Request Failed Invalid Mode For Current Configuration Invalid Request Protect Card Does Not Support Electrical Protection Protect Card Does Not Support Protection Type Sync Status Messaging (SSM) Not Allowed With SDH Mode
SSRD	Manual Switch Cannot Override Forced Switch Switch Request Denied
SSRE	Memory Resources Exceeded
SWFA	Working Unit Failed Or Missing
SWLD	Working Unit Locked

Table 7-22 Errors listed by Command
Command	Error Code	Error Message
ACT-USER	SDBE	Cannot Access Node ID Internal Database Error
	SROF	Get IOR Failed
ALW-MSG-ALL	SAAL	Already Allowed
	SAIN	Already Inhibited
ALW-MSG-DBCHG	SAAL	Already Allowed
	SAIN	Already Inhibited
ALW-PMREPT-ALL	SAAL	Already Allowed
	SAIN	Already Inhibited
ALW-SWDX-EQPT	ENEQ	Equipment Not Found
	IIAC	Invalid AID
	IICM	Input, Invalid Command
	SDBE	Internal Access Failed Internal Database Error
	SROF	Get IOR Failed
	SRQN	Invalid Request
ALW-SWTOPROTN-EQPT	ENEQ	Equipment Not Found
	IDNV	Input, Data Not Valid Invalid Protid
	IIAC	Input, Invalid Access Invalid AID
	SAAL	Already Allowed
	SDBE	Cannot Access Protection Group Internal Access Failed\| Internal Database Error
	SNVS	Protection Group Does Not Exist Working Unit Already Active Working Unit Already Standby
	SROF	Cannot Access Protection Group Information Cannot Access Protection Group Name
	SRQN	Invalid Request
ALW-SWTOWKG-EQPT	ENEQ	Equipment Not Found
	IDNV	Input, Data Not Valid Invalid Protid
	IIAC	Input, Invalid Access Invalid AID
	IICM	Input, Invalid Command
	SAAL	Already Allowed
	SDBE	Cannot Access Protection Group Internal Access Failed Internal Database Error
	SNVS	Protection Group Does Not Exist Working Unit Already Active Working Unit Already Standby
	SROF	Cannot Access Protection Group Information Cannot Access Protection Group Name Get IOR Failed
	SRQN	Invalid Request
APPLY	IIDT	Cannot Activate To Older Software Cannot Revert From R2 To R1 Cannot Revert To Newer Software Command Already In Progress Flash Manager Not Active Invalid Software Switch Type Software Activate/Revert Failed Software Not Available For Switch
	SDBE	Internal Database Error
	SROF	Get IOR Failed Software Activation Failed Software Reversion Failed
CANC-USER	SDBE	Internal Database Error
	SROF	Get IOR Failed
CHG-ACCMD-<STS_PATH>	IDNV	Invalid TAP Number
	IIAC	Equipment Does Not Match Request Multiple TAP AIDs Not Supported
	IICM	Input, Invalid Command
	RTEN	Invalid TAP AID
	SDBE	Internal Database Error
	SRCN	Already In Requested Mode
	SROF	Unknown Internal Error STS Rates Do Not Match
CHG-ACCMD-DS1	ICNV	Equipment Does Not Match Request
	IIAC	Invalid AID Multiple TAP AIDs Not Supported
	IICM	Input, Invalid Command
	SDBE	Internal Database Error
	SRCN	Already In Requested Mode
	SROF	Tap Number Does Not Exist
CHG-ACCMD-T1	ICNV	Equipment Does Not Match Request
	IIAC	Invalid AID Multiple TAP AIDs Not Supported
	IICM	Input, Invalid Command
	SDBE	Internal Database Error
	SRCN	Already In Requested Mode
	SROF	Tap Number Does Not Exist
CHG-ACCMD-T3	IDNV	Invalid TAP Number
	IIAC	Equipment Does Not Match Request Multiple TAP AIDs Not Supported
	IICM	Input, Invalid Command
	RTEN	Invalid TAP AID
	SDBE	Internal Database Error
	SRCN	Already In Requested Mode
	SROF	Unknown Internal Error STS Rates Do Not Match
CHG-ACCMD-VT1	ICNV	Equipment Does Not Match Request
	IIAC	Invalid AID Multiple TAP AIDs Not Supported
	IICM	Input, Invalid Command
	SDBE	Internal Database Error
	SRCN	Already In Requested Mode
	SROF	Tap Number Does Not Exist
CONN-TACC-<STS_PATH>	ENEQ	Equipment Not Found
	IDNV	Invalid TAP Number Multiple AIDs Not Allowed
	IIAC	Invalid AID Cannot Make Changes To Protect Card Invalid TAP Multiple AIDs Not Supported
	IICM	Input, Invalid Command
	RRNG	Invalid Slot Number
	SDBE	Cannot Access STS Internal Access Failed Internal Database Error STS Not Provisioned
	SROF	STS Rates Do Not Match Get IOR Failed
CONN-TACC-DS1	ENEQ	Equipment Not Found
	ICNV	Invalid Command
	IDNV	Invalid TAP Number
	IIAC	Cannot Make Changes To Protect Card Equipment Does Not Match Request Invalid AID Invalid DS1 AID Multiple TAP AIDs Not Supported
	IICM	Input, Invalid Command
	IPNV	Invalid Parameter
	SDBE	Internal Access Failed Internal Database Error
	SROF	Tap Number Does Not Exist Unknown Internal Error Cannot Access Cross-Connection Get IOR Failed STS Rates Do Not Match
CONN-TACC-T1	ENEQ	Equipment Not Found
	ICNV	Invalid Command
	IDNV	Invalid TAP Number
	IIAC	Cannot Make Changes To Protect Card Equipment Does Not Match Request Invalid AID Invalid DS1 AID Multiple TAP AIDs Not Supported
	IICM	Input, Invalid Command
	IPNV	Invalid Parameter
	SDBE	Internal Access Failed Internal Database Error
	SROF	Tap Number Does Not Exist Unknown Internal Error Cannot Access Cross-Connection Get IOR Failed STS Rates Do Not Match
CONN-TACC-T3	ENEQ	Equipment Not Found
	ICNV	Invalid Command
	IDNV	Invalid TAP Number
	IIAC	Cannot Make Changes To Protect Card Equipment Does Not Match Request Invalid AID Invalid DS1 AID Multiple TAP AIDs Not Supported
	IICM	Input, Invalid Command
	IPNV	Invalid Parameter
	SDBE	Internal Access Failed Internal Database Error
	SROF	Tap Number Does Not Exist Unknown Internal Error Cannot Access Cross-Connection Get IOR Failed STS Rates Do Not Match
CONN-TACC-VT1	ENEQ	Equipment Not Found
	ICNV	Invalid Command
	IIAC	Cannot Make Changes To Protect Card Equipment Does Not Match Request Invalid AID Multiple AIDs Not Supported
	IICM	Input, Invalid Command
	RRNG	Invalid Slot Number
	RTEN	Invalid TAP Number
	SDBE	Internal Access Failed Internal Database Error
	SROF	Cannot Access Cross-Connection Get IOR Failed Invalid Path Path Already In Use
COPY-RFILE	IIAC	Invalid AID
	IIDT	Hostname Missing In FTP URL Mandatory FTP URL Not Provided Null Outputs In FTP URL Parsing Only SWDL Is Supported For The xfertype Argument Package Name Missing in FTP URL Password Missing In FTP URL Unknown Error Processing FTP URL. Username Missing In FTP URL ftp:// Missing In FTP URL
	IPEX	Invalid Payload Block. Extra Parameters
	IPMS	Invalid Payload Block. Missing Mandatory Field
	SDBE	Internal Database Error
	SROF	Active Flash Not Ready Database Busy Flash Busy Generic download failure message Software Error Standby Flash Not Ready Get IOR Failed
DISC-TACC	IDNV	Invalid TAP Number
	IIAC	Multiple TAP AIDs Not Supported
	RTEN	Invalid TAP AID TAP Not Found
	SDBE	Internal Database Error
	SROF	Tap Number Does Not Exist Unknown Internal Error
DLT-BLSR	IDNV	Invalid Data For 2F-BLSR
	IIAC	Input, Invalid Node ID Input, Invalid Ring ID
	SROF	Set NodeId Failed Set RingId Failed Cannot Access Facility Cannot Set Span Revertive Mode Unless 4-Fiber Ring Cannot Set Span Revertive Time Unless 4-Fiber Ring Facility Not Provisioned Ring Reversion Failed Span Reversion Failed
	SRQN	BLSR Deletion Failed BLSR Does Not Exist Data Access Request Failed
DLT-CRS-<STS_PATH>	ENEQ	Equipment Not Found
	IIAC	Invalid AID Cannot Make Changes To Protect Card
	IICM	Input, Invalid Command
	RRNG	Invalid Slot Number
	SDBE	Internal Access Failed Internal Database Error
	SROF	Cannot Access Cross-Connection Cannot Delete Cross-Connection Get IOR Failed STS Rates Do Not Match
	SSRE	Memory Resources Exceeded
DLT-CRS-VT1	ENEQ	Equipment Not Found
	IIAC	Invalid AID Cannot Make Changes To Protect Card
	IICM	Input, Invalid Command
	RRNG	Invalid Slot Number
	SDBE	Internal Database Error Internal Access Failed
	SROF	Cannot Access Cross-Connection Cannot Delete Cross-Connection Get IOR Failed
	SSRE	Memory Resources Exceeded
DLT-EQPT	ENEQ	Equipment Not Found
	IIAC	Invalid AID
	IIDT	Invalid Data Parameter
	SDBE	Internal Access Failed Internal Database Error
	SPLD	Cannot Delete Equipment Equipment In Use
	SROF	Get IOR Failed
	SRQN	Invalid Request
DLT-FFP-<OCN_TYPE>	ENEQ	Equipment Not Found
	IDNC	Invalid Data
	IIAC	ALL, Ranging and Grouping Are Not Supported Invalid AID Invalid Protect AID Or Working AID Equipment Does Not Match Request
	IICM	Input, Invalid Command
	SDBE	Cannot Access Protection Group Delete Protection Group Failed Internal Access Failed Internal Database Error
	SROF	1+1 Protection Group Not Found Cannot Access Facility Cannot Access Protection Group Name Facility Not Provisioned Get IOR Failed
DLT-UCP-CC	IICM	Input, Invalid Command
	SDBE	Internal Database Error
	SROF	Get IOR Failed
DLT-UCP-IF	IICM	Input, Invalid Command
	SDBE	Internal Database Error
	SROF	Get IOR Failed
DLT-UCP-NBR	IICM	Input, Invalid Command
	SDBE	Internal Database Error
	SROF	Get IOR Failed
DLT-USER-SECU	PICC	Unknown CORBA Exception (Internal Error) Unknown User User Not Authorized
	PIUC	Cannot Delete The Logged In User User Currently Logged Into Another Session
	SDBE	Internal Database Error
	SROF	Get IOR Failed
ED-<OCN_TYPE>	ENEQ	Equipment Not Found
	IDNC	Invalid Data
	IDRG	Invalid PJMON Value
	IIAC	Equipment Does Not Match Request Invalid AID
	IICM	Input, Invalid Command
	SDBE	Cannot Access Equipment Cannot Access Facility Cannot Set Pointer Justification Monitoring Parameter (PJMON) Cannot Switch To E2 Byte With Express Orderwire IS Facility Does Not Exist Facility Does Not Match Request Facility Is Not Provisioned Internal Access Failed Internal Database Error Not Supported On EC1 Interface Synchronization Status Messaging (SSM)
	SROF	All DCCs In Use Cannot Access DCC Cannot Access Facility Cannot Access Performance Monitoring Statistics Facility Not Provisioned Get IOR Failed
	SRQN	Invalid Mode For Current Configuration
ED-<STS_PATH>	ENEQ	Equipment Not Found
	IDNV	Cannot Make Changes To Protect Card Invalid TAP Number Multiple AIDs Not Allowed
	IIAC	Expected Trace Not Supported On This Card Type Expected Trace String Exceeds Maximum Length (62) Incorrect Card Type Invalid AID Trace Mode Not Supported On This Card Type Trace Not Supported On This Card Type Trace String Exceeds Maximum Length (62)
	IICM	Input, Invalid Command
	IIDT	Only NORM CMD_MODE Is Supported
	IPNC	Parameters Not Compatible
	IPNV	Cannot Set Expected Path Trace In Auto Mode
	RRNG	Invalid Slot Number
	SDBE	Cannot Access STS Incompatible Parameter Values Internal Database Error STS Not Provisioned
	SROF	Cannot Access Cross-connect Cannot Access Cross-Connection Cannot Access VT Cross-connection Does Not Exist Get IOR Failed STS Rates Do Not Match
	IPNV	Cannot Set Expected Path Trace In Auto Mode
	SDBE	Internal Database Error Synchronization Status Messaging (SSM) Used Frame Format Does Not Support
ED-BITS	SROF	Get IOR Failed
	IPNV	Invalid Parameter
	SDBE	Internal Database Error Synchronization Status Messaging (SSM) Used Frame Format Does Not Support
	IIAC	Invalid AID
ED-BLSR	IDNV	Invalid Data For 2F-BLSR
	SROF	4-Fiber Ring Cannot Access Facility Cannot Set Span Revertive Mode Unless Cannot Set Span Revertive Time Unless Facility Not Provisioned Set NodeId Failed Set RingId Failed Ring Reversion Failed Span Reversion Failed
	SRQN	BLSR Deletion Failed BLSR Does Not Exist Data Access Request Failed
	IIAC	Input, Invalid Node ID Input, Invalid Ring ID
ED-CRS-<STS_PATH>	ENEQ	Equipment Not Found
	IIAC	Cannot make changes to protect card Invalid AID
	IICM	Input, Invalid Command
	RRNG	Invalid Slot Number
	SDBE	Internal Access Failed Internal Database Error
	SNCC	Cross-connection does not exist
	SROF	Get IOR Failed
	SSRE	Memory resource denial
ED-CRS-VT1	ENEQ	Equipment Not Found
	IIAC	Cannot make changes to protect card Invalid AID
	RRNG	Invalid Slot Number
	SDBE	Internal Access Failed Internal Database Error
	SNCC	Cross-connection does not exist
	SROF	Get IOR Failed
	SSRE	Memory resource denial
ED-DAT	IIAC	Invalid Year
	SDBE	Cannot Access Date/Time Cannot Set Date Cannot Set Date When Using SNTP
	SROF	Get IOR Failed
ED-DS1	ENEQ	Equipment Not Found Equipment Not Provisioned
	ICNV	Invalid Command
	IDNV	Incompatible Equipment Type Invalid TAP Number
	IIAC	Cannot Make Changes To Protect Card Equipment Does Not Match Request Invalid AID Invalid DS1 AID
	IICM	Input, Invalid Command
	IPNV	Invalid Parameter
	SDBE	Operation not supported by this card Cannot Access Object Internal Access Failed Internal Database Error
	SROF	Get IOR Failed
ED-EC1	ENEQ	Equipment Not Found
	IDNC	Invalid Data
	IIAC	Cannot Make Changes To Protect Card Equipment Does Not Match Request Invalid AID
	IICM	Input, Invalid Command
	SDBE	Internal Access Failed Internal Database Error
	SROF	Get IOR Failed
ED-EQPT	ENEQ	Equipment Not Found
	ICNV	Equipment In Use
	IDNV	Cannot Change Protection Type Command Not Valid On Protect Card Incompatible Equipment Type For Protection Incompatible Protect Slot For Protection Multiple Protection Group Card Slot Identifiers Not Allowed Protect Card Does Not Support Protection Type Protect Slot Not Provisioned Protection Group Does Not Exist
	IIAC	ALL, Ranging and Grouping Are Not Supported Invalid AID Invalid Protect AID
	IIDT	Invalid Revertive Time
	IPMS	Invalid Payload Block. Missing Mandatory Field
ED-EQPT (continued)	IPNC	Cannot Change Existing Protection Type Invalid Parameter Parameters Are Not Consistent
	IPNV	Invalid Reversion Mode For Protection Type Invalid Parameter
	SDBE	Cannot Access Protection Group Cannot Access Protection State Internal Access Failed Internal Database Error
	SNVS	Protection Group Does Not Exist
	SRCN	Requested Condition Already Exists
	SROF	Cannot Access Protection Group Information Cannot Access Protection Group Name Cannot Access Protection Group Reversion Information Cannot Change XTC Protection Group Cannot Create Protection Group Cannot Delete Protection Group Cannot Provision Protection Equipment Cannot Set Protection Group Name Get IOR Failed Protect Card Busy Unsupported Command Type
	SRQN	Invalid Request Protect Card Does Not Support Electrical Protection
ED-FFP-<OCN_TYPE>	ENEQ	Equipment Not Found
	IDNC	Invalid Data
	IIAC	Equipment Does Not Match Request Invalid AID
	IICM	Input, Invalid Command
	IIDT	Invalid Data Parameter
	SDBE	Cannot Access Protection Group Internal Access Failed Internal Database Error
	SROF	1+1 Protection Group Not Found Cannot Access Facility Cannot Access Protection Group Name Cannot Set Bidirectional Protection Group Cannot Set Protection Group Name Cannot Set Protection Group Revertive Behavior Facility Not Provisioned Get IOR Failed
ED-G1000	ENEQ	Equipment Not Found
	ICNV	Invalid Command
	IDNV	Invalid Ethernet Frame Size
	IIAC	Invalid AID Invalid G1000 Facility Port
	IPEX	Invalid Payload Block. Extra Parameters
	IPNC	Invalid Flow Control Value Invalid Maximum Frame Size
	SDBE	Internal Access Failed Internal Database Error Object Not Provisioned
	SNVS	Cannot Operate Loopback In Current State
	SROF	Get IOR Failed
ED-NE-GEN	IPNV	Invalid Default Router Address Invalid IIOP Port number Invalid IP Address Invalid IP Configuration Parameter Invalid IP Mask Invalid LAN IP Address Invalid LAN IP Mask Invalid SNTP Host Address Node Name Too Long Set LAN IP Config Failed - Different From Node IP DHCP/OSPF on LAN Is Not Allowed
	SDBE	Set LAN IP Configuration Failed Set LAN IP Config Failed - OSPF Is Provisioned Cannot Access IP Configuration Cannot Access Node ID Cannot Set IP Configuration Cannot Set Node Name Cannot Set SNTP Host Configuration Internal Database Error
	SDNA	Standby TCC Not Ready
	SROF	Cannot Access LAN IP Configuration Invalid MASK LAN IP Address Set LAN IP Config Failed - Subnets Different Get IOR Failed
ED-NE-SYNCN	SDBE	Cannot Access Synchronization Configuration Internal Database Error
	SROF	Generation1 Does Not Support Given Quality Of RES Get IOR Failed
ED-PID	PICC	Invalid User Password - Must Conform To TL1 Rules New Password Same As Old Password Unknown CORBA Exception (Internal Error) Unknown User
	PIUC	User Not Allowed To Change User Password
	SDBE	Internal Database Error
	SROF	Get IOR Failed
ED-SYNCN	IDNV	Invalid Reference Multiple References Not Allowed
	SNNS	Reference Not From Optical Card
	SROF	Get IOR Failed
	IPNV	Invalid Clock Source Primary Reference Incompatible With Timing Mode Reference Type Not Supported Secondary Reference Incompatible With Timing Mode Synchronization Source Already Defined For The Slot Third Reference Incompatible With Timing Mode Timing Mode Not Compatible
	IDNC	Primary Source Cannot Be INTERNAL When Secondary Source Is Not INTERNAL Primary Source Cannot Be INTERNAL When Third Source Is Not INTERNAL Secondary Source Cannot Be INTERNAL When Third Source Is Not INTERNAL
	SDBE	Internal Database Error
	IIAC	Invalid AID Invalid Reference
ED-T1	ENEQ	Equipment Not Found Equipment Not Provisioned
	ICNV	Invalid Command
	IDNV	Incompatible Equipment Type Invalid TAP Number
	IIAC	Cannot Make Changes To Protect Card Equipment Does Not Match Request Invalid AID Invalid DS1 AID
	IICM	Input, Invalid Command
	IPNV	Invalid Parameter
	SDBE	Operation not supported by this card Cannot Access Object Internal Access Failed Internal Database Error
	SROF	Get IOR Failed
ED-T3	ENEQ	Equipment Not Found Equipment Not Provisioned
	ICNV	Invalid Command
	IDNV	Frame Format Contains Invalid Data Frame Format Not Supported On Equipment Incompatible Equipment Type Invalid TAP Number Line Code Not Supported
	IIAC	Cannot Make Changes To Protect Card Equipment Does Not Match Request Invalid AID Invalid DS1 AID
	IICM	Input, Invalid Command
	IPNV	Invalid Parameter
	SDBE	Operation not supported by this card Cannot Access Object Internal Access Failed Internal Database Error
	SROF	Get IOR Failed
ED-UCP-CC	IIAC	Routed CC Is Not Allowed to Provision MTU & CRCMD
	IICM	Input, Invalid Command
	SDBE	Internal Database Error
	SROF	Get IOR Failed
ED-UCP-IF	IICM	Input, Invalid Command
	SDBE	Internal Database Error
	SROF	Get IOR Failed
ED-UCP-NBR	IIAC	HELLOINT Is Not Allowed If HELLOEN Is Disabled
	IICM	Input, Invalid Command
	SDBE	Internal Database Error
	SROF	Get IOR Failed
ED-UCP-NODE	IICM	Input, Invalid Command
	IPNV	Invalid Node Id
	SDBE	Internal Database Error
	SROF	Get IOR Failed
ED-USER-SECU	PICC	AID Required Invalid User Access Privilege Value Invalid User Identifier - Must Conform To TL1 Rules Invalid User Password - Must Conform To TL1 Rules New Password Same As Old Password Unknown CORBA Exception (Internal Error) Unknown User User Access Privilege Required User Already Exists User Not Authorized User Password Required
	PIUC	User Currently Logged Into Another Session. User Is Not Superuser User Not Allowed To Change User Access Privilege User Not Allowed To Change User Password
	SDBE	Internal Database Error
	SROF	Get IOR Failed Maximum User Limit Reached
ED-VT1	ENEQ	Equipment Not Found
	ICNV	Invalid Command
	IDNV	Invalid TAP Number
	IIAC	Cannot Make Changes To Protect Card Equipment Does Not Match Request Invalid AID
	IICM	Input, Invalid Command
	IIDT	Only NORM CMD_MODE Is Supported
	IPNC	Parameters Not Compatible
ED-VT1 (continued)	IPNV	Cross-Connection Does Not Have UPSR Path Selector
	RRNG	Invalid Slot Number
	SDBE	Cannot Access STS Cannot Access VT Internal Access Failed Internal Database Error STS Not Provisioned VT Not Provisioned
	SROF	Cannot Access Cross-Connection Get IOR Failed
ENT-BLSR	IIAC	Input, Invalid Duplicated Port ID Input, Invalid Node ID Input, Invalid Ring ID Input, Invalid Work/Prot Port Input Invalid MODE for BLSR Creation MODE Is Required for BLSR Creation SRVRTV/SRVTM/EASTPROT/WESTPROT Are Not Allowed for 2F-BLSR Creation RingId Does Not Match with AID Number
	SRQN	BLSR Creation Failed
ENT-CRS-<STS_PATH>	ENEQ	Equipment Not Found
	IIAC	Cannot Make Changes To Protect Card Invalid AID Only CCT=2WAY Is Allowed When G1000 Port Is Used UPSR Cross-Connections Are Not Allowed When A G1000 Port Is Used
	IICM	Input, Invalid Command
	RRNG	Invalid Slot Number
	SDBE	Internal Access Failed Internal Database Error
	SNCN	Cross-Connection Type Not Supported In TL1
	SROF	Cannot Create Cross-Connection Between Incompatible Interfaces Cross-Connection Creation Failed Get IOR Failed Insufficient Path Width For Cross-connection Invalid Cross-Connection Path Invalid UPSR Path Path Already In Use
	SSRE	Memory Resources Exceeded
ENT-CRS-VT1	SROF	Cross-Connection Creation Failed Get IOR Failed Invalid Cross-Connection Path Invalid UPSR Path Path Already In Use
	SSRE	Memory Resources Exceeded
	SDBE	Internal Access Failed Internal Database Error
	IIAC	Cannot Make Changes To Protect Card Invalid AID
ENT-EQPT	ENEQ	Equipment Not Found
	ICNV	Equipment In Use
	IDNV	At least an XC10G XC card is needed for this equipment type Command Not Valid On Protect Card Incompatible Equipment Type For Protection Incompatible Protect Slot For Protection Invalid Equipment Type Multiple Protection Group Card Slot Identifiers Not Allowed Protect Card Does Not Support Protection Type Protect Slot Not Provisioned Protection Group Card Slot Identifier Field Required
	IIAC	ALL, Ranging and Grouping Are Not Supported Invalid AID Invalid Protect AID
	IIDT	Invalid Data Parameter Invalid Revertive Time
	IPMS	Invalid Payload Block. Missing Mandatory Field
	IPNC	Cannot Change Existing Protection Type Invalid Parameter
	IPNV	Invalid Reversion Mode For Protection Type Invalid Parameter
	SAAS	Equipment Already Provisioned
	SDBE	Cannot Access Protection Group Cannot Access Protection State Internal Access Failed Internal Database Error
	SNVS	Protection Group Does Not Exist
	SPLD	Cannot Delete Equipment Equipment In Use
	SRCN	Requested Condition Already Exists
ENT-EQPT (continued)	SROF	Cannot Access Protection Group Information Cannot Access Protection Group Name Cannot Access Protection Group Reversion Information Cannot Create Protection Group Cannot Delete Protection Group Cannot Provision Equipment Cannot Provision Protection Equipment Cannot Set Protection Group Name Get IOR Failed Protect Card Busy Unsupported Command Type
	SRQN	Invalid Request Protect Card Does Not Support Electrical Protection
ENT-FFP-<OCN_TYPE>	ENEQ	Equipment Not Found
	IDMS	Missing Internal Data
	IDNC	Invalid Data
	IIAC	ALL, Ranging and Grouping Are Not Supported Equipment Does Not Match Request Invalid AID
	IICM	Input, Invalid Command
	IIDT	Memory Out Of Range
	SDBE	Cannot Create 1+1 Protection Group Internal Access Failed Internal Database Error
	SPLD	Cannot Create 1+1 Protection Group Facility Is Busy
	SROF	Get IOR Failed
ENT-UCP-CC	IIAC	PORT Data Is Needed To Create SDCC Type IPCC Routed CC Is Not Allowed to Provision MTU & CRCMD
	IICM	Input, Invalid Command
	SDBE	Internal Database Error
	SROF	Get IOR Failed
ENT-UCP-IF	IICM	Input, Invalid Command
	SDBE	Internal Database Error
	SROF	Get IOR Failed
ENT-UCP-NBR	IIAC	HELLOINT Is Not Allowed If HELLOEN Is Disabled Invalid Neighbor Node ID NBRIX Does Not Match with AID NODEID Is Not Allowed If NDEN Is Enabled Neighbor Name Can Not be Empty Node Name Too Long
	IICM	Input, Invalid Command
	SDBE	Internal Database Error
	SROF	Get IOR Failed
ENT-USER-SECU	PICC	Invalid User Access Privilege Value Invalid User Identifier - Must Conform To TL1 Rules Invalid User Password - Must Conform To TL1 Rules Unknown CORBA Exception (Internal Error) Unknown User User Already Exists User Not Authorized
	PIUC	User Is Not Superuser
	SDBE	Internal Database Error
	SROF	Get IOR Failed Maximum User Limit Reached
EX-SW-<OCN_BLSR>	IIAC	Equipment Does Not Match Request Invalid AID
	IICM	Input, Invalid Command
	IPNV	Exercise Is Not Allowed On Protected Facility Invalid Switch Type
	SDBE	Internal Access Failed Internal Database Error
	SNVS	BLSR East Operation Already Set BLSR West Operation Already Set Facility Not Part Of BLSR Invalid BLSR Element
	SROF	Cannot Access Facility Facility Not Provisioned Internal Exercise Failure Invalid Protection Switch Operation
INH-MSG-ALL	SAAL	Already Allowed
	SAIN	Already Inhibited
ING-MSG_DBCHG	SAAL	Already Allowed
	SAIN	Already Inhibited
INH-PMREPT-ALL	SAAL	Already Allowed
	SAIN	Already Inhibited
INH-SWDX-EQPT	ENEQ	Equipment Not Found
	IIAC	Invalid AID
	IICM	Input, Invalid Command
	SDBE	Internal Access Failed Internal Database Error
	SROF	Get IOR Failed
	SRQN	Invalid Request
INH-SWTOPROTN-EQPT	ENEQ	Equipment Not Found
	IDNV	Input, Data Not Valid Invalid Protid
	IIAC	Input, Invalid Access Invalid AID
	IICM	Input, Invalid Command
	SAAL	Already Allowed
	SDBE	Cannot Access Protection Group Internal Access Failed Internal Database Error
	SNVS	Protection Group Does Not Exist Working Unit Already Active Working Unit Already Standby
	SROF	Cannot Access Protection Group Information Cannot Access Protection Group Name Get IOR Failed
	SRQN	Invalid Request
INH-SWTOWKG-EQPT	ENEQ	Equipment Not Found
	IDNV	Input, Data Not Valid Invalid Protid
	IIAC	Input, Invalid Access Invalid AID
	IICM	Input, Invalid Command
	SAAL	Already Allowed
	SDBE	Cannot Access Protection Group Internal Access Failed Internal Database Error
	SNVS	Protection Group Does Not Exist Working Unit Already Active Working Unit Already Standby
INH-SWTOWKG-EQPT (continued)	SROF	Cannot Access Protection Group Information Cannot Access Protection Group Name Get IOR Failed
	SRQN	Invalid Request
INIT-REG-<OCN_TYPE>>	ENEQ	Equipment Not Found Equipment Not Present
	IDNC	Invalid Data
	IIAC	Equipment Does Not Match Request Invalid AID
	IICM	Input, Invalid Command
	SDBE	Cannot Access Equipment Internal Access Failed Internal Database Error
	SNCN	This Direction Is Not Supported
	SROF	Cannot Access Performance Monitoring Statistics Get IOR Failed
INIT-REG-<STS_PATH>	ENEQ	Equipment Not Found Equipment Not Present Internal Communication Error
	IIAC	Cannot Make Changes To Protect Card Invalid AID
	IICM	Input, Invalid Command
	SDBE	Cannot Access Equipment Internal Access Failed Internal Database Error STS Not Provisioned
	SNCN	This Direction Is Not Supported
	SROF	Get IOR Failed
INIT-REG-DS1	ENEQ	Equipment Not Found Equipment Not Present Equipment Not Provisioned Internal Communication Error
	ICNV	Invalid Command
	IDNV	Incompatible Equipment Type
	IIAC	Cannot Make Changes To Protect Card Equipment Does Not Match Request Invalid AID Invalid DS1 AID
	IICM	Input, Invalid Command
INIT-REG-DS1 (continued)	SDBE	Cannot Access Equipment Cannot Access Object Internal Access Failed Internal Database Error
	SNCN	This Direction Is Not Supported
	SROF	Get IOR Failed
INIT-REG-EC1	ENEQ	Equipment Not Found Equipment Not Present
	IDNC	Invalid Data
	IIAC	Equipment Does Not Match Request Invalid AID
	IICM	Input, Invalid Command
	SDBE	Cannot Access Equipment Internal Access Failed Internal Database Error
	SNCN	This Direction Is Not Supported
	SROF	Cannot Access Performance Monitoring Statistics Get IOR Failed
INIT-REG-T1	ENEQ	Equipment Not Found Equipment Not Present Equipment Not Provisioned Internal Communication Error
	ICNV	Invalid Command
	IDNV	Incompatible Equipment Type
	IIAC	Cannot Make Changes To Protect Card Equipment Does Not Match Request Invalid AID Invalid DS1 AID
	IICM	Input, Invalid Command
	SDBE	Cannot Access Equipment Cannot Access Object Internal Access Failed Internal Database Error
	SNCN	This Direction Is Not Supported
	SROF	Get IOR Failed
INIT-REG-T3	ENEQ	Equipment Not Found Equipment Not Present Equipment Not Provisioned Internal Communication Error
	ICNV	Invalid Command
	IDNV	Incompatible Equipment Type
NIT-REG-T3 (continued)	IIAC	Cannot Make Changes To Protect Card Equipment Does Not Match Request Invalid AID Invalid DS1 AID
	IICM	Input, Invalid Command
	SDBE	Cannot Access Equipment Cannot Access Object Internal Access Failed Internal Database Error
	SNCN	This Direction Is Not Supported
	SROF	Get IOR Failed
INIT-REG-VT1	ICNV	Invalid Command Operation not supported by this card
	IIAC	Cannot Make Changes To Protect Card Equipment Does Not Match Request Invalid AID
	IICM	Input, Invalid Command
	SDBE	Cannot Access VT Internal Database Error VT Not Provisioned
	SNCN	This Direction Is Not Supported
	SROF	Get IOR Failed Operation Not Supported
INIT-SYS	ENEQ	Equipment Not Found Equipment Not Present
	IIAC	ALL, Ranging and Grouping Are Not Supported Invalid AID
	SDBE	Cannot Access Equipment Internal Access Failed Internal Database Error
	SROF	Get IOR Failed MIC Cards Cannot Be Reset
	SRQN	Invalid Request
OPR-ACO-ALL	SROF	Operate Alarm Cutoff Failed
OPR-EXT-CONT	ENEQ	Control Not Provisioned
	SAOP	Control Already Operated Control Not Operated Or Already Released
	SDBE	Cannot Access Controls Internal Database Error
	SROF	Get IOR Failed Invalid Control Type (CONTTYPE) For AID
	SRQN	Invalid Request
OPR-LPBK-<OCN_TYPE>	ENEQ	Equipment Not Found
	IDNC	Invalid Data
	IIAC	Equipment Does Not Match Request Invalid AID
	IICM	Input, Invalid Command
	SDBE	Cannot Access Facility Cannot Access Interface Internal Access Failed Internal Database Error
	SNVS	Cannot Operate Loopback In Current State
	SROF	Get IOR Failed Invalid Loopback Provision
OPR-LPBK-DS1	ENEQ	Equipment Not Found
	ICNV	Invalid Command
	IIAC	Cannot Make Changes To Protect Card Equipment Does Not Match Request Invalid AID Invalid DS1 AID
	IICM	Input, Invalid Command
	SDBE	Cannot Access Interface Cannot Access Object Internal Database Error
	SNVS	Cannot Operate Loopback In Current State Loopback Already In Progress Loopback Not In Progress
	SROF	Get IOR Failed Invalid Loopback Provision Loopback Type Does Not Match
OPR-LPBK-EC1	ENEQ	Equipment Not Found
	IDNC	Invalid Data
	IIAC	Cannot Make Changes To Protect Card Equipment Does Not Match Request Invalid AID
	IICM	Input, Invalid Command
	SDBE	Cannot Access Interface Internal Access Failed Internal Database Error
	SNVS	Cannot Operate Loopback In Current State Loopback Already In Progress Loopback Not In Progress
OPR-LPBK-EC1 (continued)	SROF	Get IOR Failed Invalid Loopback Provision Loopback Type Does Not Match Requested Operation Failed
OPR-LPBK-G1000	ENEQ	Equipment Not Found
	ICNV	Invalid Command
	IDNV	Facility Loopback Not Supported Invalid Ethernet Frame Size
	IIAC	Invalid AID Invalid G1000 Facility Port
	SDBE	Internal Access Failed Internal Database Error Object Not Provisioned
	SNVS	Cannot Operate Loopback In Current State Loopback Already In Progress Loopback Not In Progress
	SROF	Get IOR Failed Unsupported Command Type
OPR-LPBK-T1	ENEQ	Equipment Not Found
	ICNV	Invalid Command
	IIAC	Cannot Make Changes To Protect Card Equipment Does Not Match Request Invalid AID Invalid DS1 AID
	IICM	Input, Invalid Command
	SDBE	Cannot Access Interface Cannot Access Object Internal Access Failed Internal Database Error
	SNVS	Cannot Operate Loopback In Current State Loopback Already In Progress Loopback Not In Progress
	SROF	Get IOR Failed Invalid Loopback Provision Loopback Type Does Not Match
OPR-LPBK-T3	ENEQ	Equipment Not Found
	ICNV	Invalid Command
	IIAC	Cannot Make Changes To Protect Card Equipment Does Not Match Request Invalid AID Invalid DS1 AID
	IICM	Input, Invalid Command
OPR-LPBK-T3 (continued)	SDBE	Cannot Access Interface Cannot Access Object Internal Access Failed Internal Database Error
	SNVS	Cannot Operate Loopback In Current State Loopback Already In Progress Loopback Not In Progress
	SROF	Get IOR Failed Invalid Loopback Provision Loopback Type Does Not Match
OPR-PROTNSW-<OCN_TYPE>	ENEQ	Equipment Not Found
	IDNC	Invalid Data
	IIAC	Equipment Does Not Match Request Invalid AID
	IICM	Input, Invalid Command
	SAMS	Already In Clear Maintenance State Already In Force Maintenance State Already In Lockout Maintenance State Already In Manual Maintenance State
	SDBE	Cannot Access Facility Facility Does Not Match Request Facility Is Not Provisioned Internal Access Failed Internal Database Error
	SROF	Cannot Access Facility Facility Not Provisioned Get IOR Failed
OPR-PROTNSW-<STS_PATH>	ENEQ	Equipment Not Found
	IDNV	Multiple AIDs Not Allowed
	IIAC	Invalid AID AID Validation Failed Invalid Operation On Drop AID
	IICM	Input, Invalid Command
	RRNG	Invalid Slot Number
	SDBE	Cannot Access Facility Internal Access Failed Internal Database Error STS Not Provisioned
OPR-PROTNSW-<STS_PATH> (continued)	SROF	Cannot Access Cross-Connection Cannot Switch For Specified Connection Type Cannot Switch For Specified Path Get IOR Failed Invalid Protection Switch Operation Path Specified Is Not Valid Requested Operation Failed Specified Operation Is Not Valid
	SSRD	Switch Request Denied
OPR-PROTNSW-VT1	ENEQ	Equipment Not Found
	ICNV	Invalid Command
	IIAC	Equipment Does Not Match Request Invalid AID Invalid Operation On Drop AID
	IICM	Input, Invalid Command
	RRNG	Invalid Slot Number
	SDBE	Internal Access Failed Internal Database Error
	SROF	Cannot Access Cross-Connection Get IOR Failed Invalid Operation For Connection Type Invalid Operation For Specified Path Invalid Protection Switch Operation Path Specified Is Not Valid Requested Operation Failed Specified Operation Is Not Valid
	SSRD	Switch Request Denied
OPR-SYNCNSW	SNVS	Already Switched To Internal Reference Source Cannot Manually Switch To Active Timing Source Invalid Clock Source
	SROF	Get IOR Failed
	SNCN	Cannot Switch To Inferior Reference Source Clock Source Failed Invalid Clock Source
	SSRD	Manual Switch Cannot Override Forced Switch
	IPNV	INT Not Valid For BITS-OUT Invalid Parameter Invalid Switch Command For Synchronization New Source Must Be Specified Reference Type Not Supported
	SDBE	Internal Database Error
	IIAC	Invalid AID
RLS-EXT-CONT	ENEQ	Control Not Provisioned
	IIAC	Invalid AID
	SAOP	Control Already Operated Control Not Operated Or Already Released
	SDBE	Cannot Access Controls Internal Database Error
	SROF	Get IOR Failed Invalid Control Type (CONTTYPE) For AID
	SRQN	Invalid Request
RLS-LPBK-<OCN_TYPE>	ENEQ	Equipment Not Found
	IIAC	Equipment Does Not Match Request Invalid AID
	IICM	Input, Invalid Command
	SDBE	Cannot Access Facility Cannot Access Interface Internal Access Failed Internal Database Error
	SNVS	Cannot Operate Loopback In Current State
	SROF	Get IOR Failed Invalid Loopback Provision
RLS-LPBK-DS1	ENEQ	Equipment Not Found
	ICNV	Invalid Command
	IIAC	Cannot Make Changes To Protect Card Equipment Does Not Match Request Invalid AID Invalid DS1 AID
	IICM	Input, Invalid Command
	SDBE	Cannot Access Interface Cannot Access Object Internal Access Failed Internal Database Error
	SNVS	Cannot Operate Loopback In Current State Loopback Already In Progress Loopback Not In Progress
	SROF	Get IOR Failed Invalid Loopback Provision Loopback Type Does Not Match
RLS-LPBK-EC1	ENEQ	Equipment Not Found
	IDNC	Invalid Data
	IIAC	Cannot Make Changes To Protect Card Equipment Does Not Match Request Invalid AID
	IICM	Input, Invalid Command
	SDBE	Cannot Access Interface Internal Access Failed Internal Database Error
	SNVS	Cannot Operate Loopback In Current State Loopback Already In Progress Loopback Not In Progress
	SROF	Get IOR Failed Invalid Loopback Provision Loopback Type Does Not Match Requested Operation Failed
RLS-LPBK-G1000	ENEQ	Equipment Not Found
	ICNV	Invalid Command
	IDNV	Facility Loopback Not Supported Invalid Ethernet Frame Size
	IIAC	Invalid AID Invalid G1000 Facility Port
	SDBE	Internal Access Failed Internal Database Error Object Not Provisioned
	SNVS	Cannot Operate Loopback In Current State Loopback Already In Progress Loopback Not In Progress
	SROF	Get IOR Failed Unsupported Command Type
RLS-LPBK-T1	ENEQ	Equipment Not Found
	ICNV	Invalid Command
	IIAC	Cannot Make Changes To Protect Card Equipment Does Not Match Request Invalid AID Invalid DS1 AID
	IICM	Input, Invalid Command
	SDBE	Cannot Access Interface Cannot Access Object Internal Access Failed Internal Database Error
RLS-LPBK-T1 (continued)	SNVS	Cannot Operate Loopback In Current State Loopback Already In Progress Loopback Not In Progress
	SROF	Get IOR Failed Invalid Loopback Provision Loopback Type Does Not Match
RLS-LPBK-T3	ENEQ	Equipment Not Found
	ICNV	Invalid Command
	IIAC	Cannot Make Changes To Protect Card Equipment Does Not Match Request Invalid AID Invalid DS1 AID
	IICM	Input, Invalid Command
	SDBE	Cannot Access Interface Cannot Access Object Internal Access Failed Internal Database Error
	SNVS	Cannot Operate Loopback In Current State Loopback Already In Progress Loopback Not In Progress
	SROF	Get IOR Failed Invalid Loopback Provision Loopback Type Does Not Match
RLS-PROTNSW-<OCN_TYPE>	ENEQ	Equipment Not Found
	IDNC	Invalid Data
	IIAC	Equipment Does Not Match Request Invalid AID
	IICM	Input, Invalid Command
	SAMS	Already In Clear Maintenance State Already In Force Maintenance State Already In Lockout Maintenance State Already In Manual Maintenance State
	SDBE	Cannot Access Facility Facility Does Not Match Request Facility Is Not Provisioned Internal Access Failed Internal Database Error
	SROF	Cannot Access Facility Facility Not Provisioned Get IOR Failed
RLS-PROTNSW-<STS_PATH>	ENEQ	Equipment Not Found
	IDNV	Multiple AIDs Not Allowed
	IIAC	Invalid AID Invalid Aid AID Validation Failed Invalid AID Invalid Operation On Drop AID
	IICM	Input, Invalid Command
	RRNG	Invalid Slot Number
	SDBE	Cannot Access STS Internal Access Failed Internal Database Error STS Not Provisioned
	SROF	Cannot Access Cross-Connection Cannot Switch For Specified Connection Type Cannot Switch For Specified Path Get IOR Failed Invalid Protection Switch Operation Path Specified Is Not Valid Requested Operation Failed Specified Operation Is Not Valid
	SSRD	Switch Request Denied
RLS-PROTNSW-VT1	ENEQ	Equipment Not Found
	ICNV	Invalid Command
	IIAC	Equipment Does Not Match Request Invalid AID Invalid Operation On Drop AID
	IICM	Input, Invalid Command
	RRNG	Invalid Slot Number
	SDBE	Internal Access Failed Internal Database Error
	SROF	Cannot Access Cross-Connection Get IOR Failed Invalid Operation For Connection Type Invalid Operation For Specified Path Invalid Protection Switch Operation Path Specified Is Not Valid Requested Operation Failed Specified Operation Is Not Valid
	SSRD	Switch Request Denied
RLS-SYNCNSW	IIAC	Invalid AID
	SDBE	Internal Database Error
	SROF	Get IOR Failed
	SNVS	No Switch In Progress
RMV-<OCN_TYPE>	ENEQ	Equipment Not Found
	IDNC	Invalid Data
	IIAC	Equipment Does Not Match Request Invalid AID
	IICM	Input, Invalid Command
	IIDT	Only NORM CMD_MODE Is Supported Only OOS PST Is Supported
	SDBE	Internal Access Failed Internal Database Error
	SROF	Get IOR Failed
RMV-DS1	ENEQ	Equipment Not Found
	ICNV	Invalid Command
	IIAC	Equipment Does Not Match Request Invalid AID
	IDNV	Incompatible Equipment Type Invalid TAP Number
	IIAC	Cannot Make Changes To Protect Card Equipment Does Not Match Request Invalid AID Invalid DS1 AID
	IICM	Input, Invalid Command
	IPNV	Invalid Parameter
	SDBE	Operation not supported by this card Cannot Access Object Internal Access Failed Internal Database Error
	SROF	Get IOR Failed
RMV-EC1	ENEQ	Equipment Not Found
	IDNC	Invalid Data
	IIAC	Equipment Does Not Match Request Invalid AID
	IIAC	Equipment Does Not Match Request Invalid AID
	IICM	Input, Invalid Command
	IIDT	Only NORM CMD_MODE Is Supported Only OOS PST Is Supported
RMV-EC1 (continued)	SDBE	Internal Access Failed Internal Database Error
	SROF	Get IOR Failed
RMV-G1000	ENEQ	Equipment Not Found
	IIAC	Invalid AID Invalid G1000 Facility Port
	IIDT	Invalid State Value Only NORM CMD_MODE Is Supported
	SDBE	Internal Access Failed Internal Database Error
	SROF	Command Not Supported Get IOR Failed
RMV-T1	ENEQ	Equipment Not Found
	ICNV	Invalid Command
	IIAC	Equipment Does Not Match Request Invalid AID Invalid DS1 AID
	IICM	Input, Invalid Command
	IIDT	Only NORM CMD_MODE Is Supported Only OOS PST Is Supported
	SDBE	Internal Access Failed Internal Database Error
	SROF	Get IOR Failed
RMV-T3	ENEQ	Equipment Not Found
	ICNV	Invalid Command
	IIAC	Equipment Does Not Match Request Invalid AID Invalid DS1 AID
	IICM	Input, Invalid Command
	IIDT	Only NORM CMD_MODE Is Supported Only OOS PST Is Supported
	SDBE	Internal Access Failed Internal Database Error
	SROF	Get IOR Failed
RST-<OCN_TYPE>	ENEQ	Equipment Not Found
	IDNC	Invalid Data
	IIAC	Equipment Does Not Match Request Invalid AID
	IICM	Input, Invalid Command
	IIDT	Only NORM CMD_MODE Is Supported Only OOS PST Is Supported
	SDBE	Internal Access Failed Internal Database Error
	SROF	Get IOR Failed
RST-DS1	ENEQ	Equipment Not Found
	ICNV	Invalid Command
	IIAC	Equipment Does Not Match Request Invalid AID
	IDNV	Incompatible Equipment Type Invalid TAP Number
	IIAC	Cannot Make Changes To Protect Card Equipment Does Not Match Request Invalid AID Invalid DS1 AID
	IICM	Input, Invalid Command
	IPNV	Invalid Parameter
	SDBE	Operation not supported by this card Cannot Access Object Internal Access Failed Internal Database Error
	SROF	Get IOR Failed
RST-EC1	ENEQ	Equipment Not Found
	IDNC	Invalid Data
	IIAC	Equipment Does Not Match Request Invalid AID
	IICM	Input, Invalid Command
	SDBE	Internal Access Failed Internal Database Error
	SROF	Get IOR Failed
RST-G1000	ENEQ	Equipment Not Found
	IIAC	Invalid AID Invalid G1000 Facility Port
	IIDT	Invalid State Value Only NORM CMD_MODE Is Supported
	SDBE	Internal Access Failed Internal Database Error
	SROF	Command Not Supported Get IOR Failed
RST-T1	ENEQ	Equipment Not Found
	ICNV	Invalid Command
	IIAC	Equipment Does Not Match Request Invalid AID Invalid DS1 AID
	IICM	Input, Invalid Command
	SDBE	Internal Access Failed Internal Database Error
	SROF	Get IOR Failed
RST-T3	ENEQ	Equipment Not Found
	ICNV	Invalid Command
	IIAC	Equipment Does Not Match Request Invalid AID Invalid DS1 AID
	IICM	Input, Invalid Command
	SDBE	Internal Access Failed Internal Database Error
	SROF	Get IOR Failed
RTRV-<OCN_TYPE>	ENEQ	Equipment Not Found
	IDNC	Invalid Data
	IIAC	Equipment Does Not Match Request Invalid AID
	IICM	Input, Invalid Command
	SDBE	Cannot Access Equipment Cannot Access Facility Cannot Access IP Configuration Facility Does Not Exist Facility Does Not Match Request Facility Is Not Provisioned Internal Access Failed Internal Database Error
RTRV-<OCN_TYPE> (continued)	SROF	Cannot Access Facility Cannot Access Performance Monitoring Statistics Facility Not Provisioned Get IOR Failed
RTRV-<STS_PATH>	ENEQ	Equipment Not Found Equipment Not Present
	IDNV	Multiple AIDs Not Allowed
	IIAC	AID Validation Failed Invalid AID
	IICM	Input, Invalid Command
	RRNG	Invalid Slot Number
	SDBE	Cannot Access STS Cannot Access Equipment Cannot Access STS Internal Access Failed Internal Database Error STS Not Provisioned
	SNVS	Invalid Admin State
	SROF	Cannot Access Cross-connect Cannot Access Cross-Connection Get IOR Failed
RTRV-ALM-<OCN_TYPE>	ENEQ	Equipment Not Found
	IDNC	Invalid Data
	IIAC	Equipment Does Not Match Request Invalid AID
	IICM	Input, Invalid Command
	SDBE	Internal Access Failed Internal Database Error
	SROF	Get IOR Failed
RTRV-ALM-<STS_PATH>	IIAC	Invalid AID
	IICM	Input, Invalid Command
	SDBE	Cannot Access Conditions Cannot Access STS Internal Database Error STS Not Provisioned
	SROF	Get IOR Failed
RTRV-ALM-ALL	ENEQ	Equipment Not Found
	IIAC	Invalid AID
	RRNG	Invalid Slot Number
	SDBE	Cannot Access Object Internal Access Failed Internal Database Error
	SROF	Get IOR Failed
RTRV-ALM-BITS	IIAC	Invalid AID
	SDBE	Cannot Access Conditions
	SROF	Get IOR Failed
RTRV-ALM-DS1	IIAC	Equipment Does Not Match Request Invalid AID Invalid DS1 AID
	IICM	Input, Invalid Command
	SDBE	Cannot Access Conditions Internal Access Failed Internal Database Error
	SROF	Get IOR Failed
RTRV-ALM-E100	ENEQ	Equipment Not Found
	IDNC	Invalid Data
	IIAC	Equipment Does Not Match Request Invalid AID
	SDBE	Internal Access Failed Internal Database Error
	SROF	Get IOR Failed
RTRV-ALM-E1000	ENEQ	Equipment Not Found
	IDNC	Invalid Data
	IIAC	Equipment Does Not Match Request Invalid AID
	SDBE	Internal Access Failed Internal Database Error
	SROF	Get IOR Failed
RTRV-ALM-EC1	ENEQ	Equipment Not Found
	IDNC	Invalid Data
	IIAC	Equipment Does Not Match Request Invalid AID
	IICM	Input, Invalid Command
	SDBE	Cannot Access Conditions Internal Access Failed Internal Database Error
	SROF	Get IOR Failed
RTRV-ALM-ENV	IIAC	Invalid AID
	SDBE	Cannot Access Conditions Internal Database Error
	SROF	Get IOR Failed
	SRQN	Invalid Request
RTRV-ALM-EQPT	ENEQ	Equipment Not Found Equipment Not Present
	IIAC	Invalid AID
	SDBE	Cannot Access Conditions Cannot Access Equipment Internal Access Failed Internal Database Error
	SROF	Get IOR Failed
	SRQN	Invalid Request
RTRV-ALM-G1000	ENEQ	Equipment Not Found
	IDNC	Invalid Data
	IIAC	Equipment Does Not Match Request Invalid AID
	SDBE	Internal Access Failed Internal Database Error
	SROF	Get IOR Failed
RTRV-ALM-RING	IIAC	Invalid AID
	SDBE	Internal Database Error
	SROF	Cannot Access BLSR Get IOR Failed
	SRQN	BLSR Does Not Exist
RTRV-ALM-T1	ENEQ	Equipment Not Found
	ICNV	Invalid Command
	IIAC	Equipment Does Not Match Request Invalid AID Invalid DS1 AID
	IICM	Input, Invalid Command
	SDBE	Cannot Access Conditions Internal Access Failed Internal Database Error
	SROF	Get IOR Failed
RTRV-ALM-T3	ENEQ	Equipment Not Found
	ICNV	Invalid Command
	IIAC	Equipment Does Not Match Request Invalid AID Invalid DS1 AID
	IICM	Input, Invalid Command
	SDBE	Cannot Access Conditions Internal Access Failed Internal Database Error
	SROF	Get IOR Failed
RTRV-ALM-SYNCN	SROF	Get IOR Failed
	SDBE	Cannot Access Conditions Internal Database Error
	IIAC	Invalid AID
RTRV-ALM-UCP	IICM	Input, Invalid Command
	SDBE	Internal Database Error
	SROF	Get IOR Failed
RTRV-ALM-UDCDCC	IIAC	Invalid AID
	SDBE	Cannot Access Conditions Internal Database Error
	SROF	Get IOR Failed
	SRQN	Invalid Request
RTRV-ALM-UDCF	IIAC	Invalid AID
	SDBE	Cannot Access Conditions Internal Database Error
	SROF	Get IOR Failed
	SRQN	Invalid Request
RTRV-ALM-VT1	ICNV	Invalid Command
	IIAC	Equipment Does Not Match Request Invalid AID
	IICM	Input, Invalid Command
	SDBE	Cannot Access Conditions Internal Database Error
	SROF	Get IOR Failed
RTRV-ATTR-CONT	IIAC	Invalid AID
	SDBE	Cannot Access Controls Internal Database Error
	SROF	Get IOR Failed
	SRQN	Invalid Request
RTRV-ATTR-ENV	IIAC	Invalid AID
	SDBE	Cannot Access Environmental Settings Internal Database Error
	SROF	Get IOR Failed
	SRQN	Invalid Request
RTRV-BITS	IIAC	Invalid AID
	SDBE	Internal Database Error
	SROF	Get IOR Failed
RTRV-BLSR	IIAC	Invalid AID
	SDBE	Internal Database Error
	SROF	Cannot Access BLSR Get IOR Failed
	SRQN	BLSR Does Not Exist
RTRV-COND-<OCN_TYPE>	ENEQ	Equipment Not Found
	IDNC	Invalid Data
	IIAC	Equipment Does Not Match Request Invalid AID
	IICM	Input, Invalid Command
	SDBE	Cannot Access Object Internal Access Failed Internal Database Error
	SROF	Get IOR Failed
RTRV-COND-<STS_PATH>	IIAC	Invalid AID
	IICM	Input, Invalid Command
	SDBE	Cannot Access Object Cannot Access STS Internal Database Error STS Not Provisioned
	SROF	Get IOR Failed
RTRV-COND-ALL	ENEQ	Equipment Not Found
	IIAC	Invalid AID
	RRNG	Invalid Slot Number
	SDBE	Cannot Access Object Internal Access Failed Internal Database Error
	SROF	Get IOR Failed
RTRV-COND-BITS	IIAC	Invalid AID
	SROF	Get IOR Failed
RTRV-COND-DS1	ENEQ	Equipment Not Found
	ICNV	Invalid Command
	IIAC	Equipment Does Not Match Request Invalid AID Invalid DS1 AID
	IICM	Input, Invalid Command
	SDBE	Cannot Access Object Internal Access Failed Internal Database Error
	SROF	Get IOR Failed
RTRV-COND-E100	ENEQ	Equipment Not Found
	IDNC	Invalid Data
	IIAC	Equipment Does Not Match Request Invalid AID
	SDBE	Cannot Access Object Internal Access Failed Internal Database Error
	SROF	Get IOR Failed
RTRV-COND-E1000	ENEQ	Equipment Not Found
	IDNC	Invalid Data
	IIAC	Equipment Does Not Match Request Invalid AID
	SDBE	Cannot Access Object Internal Access Failed Internal Database Error
	SROF	Get IOR Failed
RTRV-COND-EC1	ENEQ	Equipment Not Found
	IDNC	Invalid Data
	IIAC	Equipment Does Not Match Request Invalid AID
	IICM	Input, Invalid Command
	SDBE	Cannot Access Object Internal Access Failed Internal Database Error
	SROF	Get IOR Failed
RTRV-COND-ENV	IIAC	Invalid AID
	SDBE	Cannot Access Object Internal Database Error
	SROF	Get IOR Failed
	SRQN	Invalid Request
RTRV-COND-EQPT	ENEQ	Equipment Not Found Equipment Not Present
	IIAC	Invalid AID
	SDBE	Cannot Access Equipment Cannot Access Object Internal Access Failed Internal Database Error
	SROF	Get IOR Failed
	SRQN	Invalid Request
RTRV-COND-G1000	ENEQ	Equipment Not Found
	IDNC	Invalid Data
	IIAC	Equipment Does Not Match Request Invalid AID
	SDBE	Cannot Access Object Internal Access Failed Internal Database Error
	SROF	Get IOR Failed
RTRV-COND-RING	IIAC	Invalid AID
	SDBE	Internal Database Error
	SROF	Cannot Access BLSR Get IOR Failed
	SRQN	BLSR Does Not Exist
RTRV-COND-T1	ENEQ	Equipment Not Found
	ICNV	Invalid Command
	IIAC	Equipment Does Not Match Request Invalid AID Invalid DS1 AID
	IICM	Input, Invalid Command
	SDBE	Cannot Access Object Internal Access Failed Internal Database Error
	SROF	Get IOR Failed
RTRV-COND-T3	ENEQ	Equipment Not Found
	ICNV	Invalid Command
	IIAC	Equipment Does Not Match Request Invalid AID Invalid DS1 AID
	IICM	Input, Invalid Command
	SDBE	Cannot Access Object Internal Access Failed Internal Database Error
	SROF	Get IOR Failed
RTRV-COND-SYNCN	IIAC	Invalid AID
	SDBE	Internal Database Error
	SROF	Get IOR Failed
RTRV-COND-UCP	IICM	Input, Invalid Command
	SDBE	Internal Database Error
	SROF	Get IOR Failed
RTRV-COND-UDCDCC	IIAC	Invalid AID
	SDBE	Cannot Access Object Internal Database Error
	SROF	Get IOR Failed
	SRQN	Invalid Request
RTRV-COND-UDCF	IIAC	Invalid AID
	SDBE	Cannot Access Object Internal Database Error
	SROF	Get IOR Failed
	SRQN	Invalid Request
RTRV-COND-VT1	ICNV	Invalid Command
	IIAC	Equipment Does Not Match Request Invalid AID
	SDBE	Cannot Access Object Internal Database Error
	SROF	Get IOR Failed
RTRV-CRS	ENEQ	Equipment Not Found
	IIAC	Invalid AID
	RRNG	Invalid Slot Number
	SDBE	Internal Access Failed Internal Database Error
	SROF	Cannot Access 1+1 Line Cannot Access 1+1 Protected Line Cannot Access 4F BLSR Cannot Access BLSR 2 Wire Line Cannot Access Cross-Connection Cannot Access Unprotected Line Element Not Found Get IOR Failed Requested Operation Failed Unsupported Element Type
RTRV-CRS-<STS_PATH>	ENEQ	Equipment Not Found
	IIAC	Invalid AID
	IICM	Input, Invalid Command
	RRNG	Invalid Slot Number
	SDBE	Internal Access Failed Internal Database Error
	SROF	Cannot Access Cross-Connection Get IOR Failed
RTRV-CRS-VT1	ENEQ	Equipment Not Found
	IIAC	Invalid AID
	IICM	Input, Invalid Command
	RRNG	Invalid Slot Number
	SDBE	Internal Access Failed Internal Database Error
	SROF	Cannot Access Cross-Connection Get IOR Failed
RTRV-DS1	ENEQ	Equipment Not Found
	ICNV	Invalid Command
	IIAC	Equipment Does Not Match Request Invalid AID Invalid DS1 AID
	IICM	Input, Invalid Command
	IPNV	Invalid Parameter
	SDBE	Cannot Access Object Internal Access Failed Internal Database Error
	SROF	Get IOR Failed
RTRV-EC1	ENEQ	Equipment Not Found
	IDNC	Invalid Data
	IIAC	Equipment Does Not Match Request Invalid AID
	IICM	Input, Invalid Command
	SDBE	Facility Does Not Exist Incorrect Facility Type Internal Access Failed Internal Database Error
	SROF	Get IOR Failed
RTRV-EQPT	ENEQ	Equipment Not Found Equipment Not Present
	IIAC	Invalid AID
	SDBE	Cannot Access Equipment Cannot Access Protection Group Internal Access Failed Internal Database Error
	SNVS	Invalid Admin State Protection Group Does Not Exist
RTRV-EQPT (continued)	SROF	Cannot Access Cross-connect Cannot Access Protection Group Information Cannot Access Protection Group Name Get IOR Failed
	SRQN	Invalid Request
RTRV-EXT-CONT	IIAC	Invalid AID
	SDBE	Cannot Access Controls Internal Database Error
	SROF	Get IOR Failed
	SRQN	Invalid Request
RTRV-FFP-<OCN_TYPE>	ENEQ	Equipment Not Found
	IDNC	Invalid Data
	IIAC	Equipment Does Not Match Request Invalid AID
	IICM	Input, Invalid Command
	SDBE	Cannot Access Protection Group Internal Access Failed Internal Database Error
	SROF	1+1 Protection Group Not Found Cannot Access Facility Cannot Access Protection Group Name Facility Not Provisioned Get IOR Failed
RTRV-G1000	ENEQ	Equipment Not Found Equipment Not Present
	ICNV	Invalid Command
	IIAC	Invalid AID Invalid G1000 Facility Port
	SDBE	Cannot Access Equipment Internal Access Failed Internal Database Error Object Not Provisioned
	SROF	Get IOR Failed
RTRV-INV	ENEQ	Equipment Not Found Equipment Not Present
	IIAC	Invalid AID List AID Not Allowed For ALL AID
	SDBE	Cannot Access Equipment Internal Access Failed Internal Database Error
	SROF	Get IOR Failed
	SRQN	Invalid Request
RTRV-LOG	IDNV	Invalid Log Name
	SDBE	Internal Database Error
	SROF	Cannot Access Alarm Log Get IOR Failed
RTRV-MAP-NETWORK	IPNV	Internal-Ip Lookup Failed
	SDBE	Cannot Access IP Configuration Internal Database Error
	SROF	DCC Not In Use Get IOR Failed
RTRV-NE-GEN	SDBE	Cannot Access Defaults Description Cannot Access IP Configuration Cannot Access Node ID Cannot Access SNTP Host Cannot Access Software Version Cannot Access Synchronization Configuration Internal Database Error
	SROF	Cannot Access LAN IP Configuration Get IOR Failed
RTRV-NE IPMAP	ENEQ	Equipment Not Found
	IIAC	Equipment Does Not Match Request Invalid AID
	IPNV	Invalid IP Address
	SDBE	Cannot Access IP Configuration Internal Access Failed Internal Database Error
	SROF	DCC Not In Use Get IOR Failed
RTRV-NE-SYNCN	SDBE	Cannot Access Synchronization Configuration Internal Database Error
	SROF	Get IOR Failed
RTRV-PM-<OCN_TYPE>	ENEQ	Equipment Not Found Equipment Not Present
	IDNC	Invalid Data
	IDNV	Interval Out Of Range Invalid MONLEV Value Invalid MONTYPE Value
	IIAC	Equipment Does Not Match Request Invalid AID
	IICM	Input, Invalid Command
RTRV-PM-<OCN_TYPE> (continued)	SDBE	Cannot Access Equipment Facility Does Not Exist Internal Access Failed Internal Database Error
	SNCN	This Direction Is Not Supported
	SROF	Cannot Access Performance Monitoring Statistics Get IOR Failed
RTRV-PM-<STS_PATH>	ENEQ	Equipment Not Found Equipment Not Present Internal Communication Error
	IDNV	Interval Out Of Range Invalid MONLEV Value Invalid MONTYPE Value
	IIAC	Invalid AID
	IICM	Input, Invalid Command
	IPNV	Far End Performance Monitoring Values Not Supported
	SDBE	Cannot Access Equipment Cannot Access STS Internal Access Failed Internal Database Error STS Not Provisioned
	SNCN	This Direction Is Not Supported
	SROF	Get IOR Failed
RTRV-PM-DS1	ENEQ	Equipment Not Found Equipment Not Present Equipment Not Provisioned Internal Communication Error
	ICNV	Invalid Command
	IDNV	Incompatible Equipment Type Interval Out Of Range Invalid MONLEV Value Invalid MONTYPE Value
	IIAC	Equipment Does Not Match Request Invalid AID Invalid DS1 AID
	IICM	Input, Invalid Command
	IPNV	Far End Performance Monitoring Values Not Supported PM Not Supported
RTRV-PM-DS1 (continued)	SDBE	Cannot Access Equipment Cannot Access Object Card Type Not Supported Internal Access Failed Internal Database Error
	SNCN	This Direction Is Not Supported
	SROF	Equipment Does Not Match Request Get IOR Failed
RTRV-PM-EC1	ENEQ	Equipment Not Found Equipment Not Present
	IDNC	Invalid Data
	IDNV	Interval Out Of Range Invalid MONLEV Value Invalid MONTYPE Value
	IIAC	Equipment Does Not Match Request Invalid AID
	IICM	Input, Invalid Command
	SDBE	Cannot Access Equipment Facility Does Not Exist Internal Access Failed Internal Database Error
	SNCN	This Direction Is Not Supported
	SROF	Cannot Access Performance Monitoring Statistics Get IOR Failed
RTRV-PM-T1	ENEQ	Equipment Not Found Equipment Not Present Equipment Not Provisioned Internal Communication Error
	ICNV	Invalid Command
	IDNV	Incompatible Equipment Type Interval Out Of Range Invalid MONLEV Value Invalid MONTYPE Value
	IIAC	Equipment Does Not Match Request Invalid AID Invalid DS1 AID
	IICM	Input, Invalid Command
	IPNV	Far End Performance Monitoring Values Not Supported PM Not Supported
RTRV-PM-T1 (continued)	SDBE	Cannot Access Equipment Cannot Access Object Card Type Not Supported Internal Access Failed Internal Database Error
	SNCN	This Direction Is Not Supported
	SROF	Equipment Does Not Match Request Get IOR Failed
RTRV-PM-T3	ENEQ	Equipment Not Found Equipment Not Present Equipment Not Provisioned Internal Communication Error
	ICNV	Invalid Command
	IDNV	Incompatible Equipment Type Interval Out Of Range Invalid MONLEV Value Invalid MONTYPE Value
	IIAC	Equipment Does Not Match Request Invalid AID Invalid DS1 AID
	IICM	Input, Invalid Command
	IPNV	Far End Performance Monitoring Values Not Supported PM Not Supported
	SDBE	Cannot Access Equipment Cannot Access Object Card Type Not Supported Internal Access Failed Internal Database Error
	SNCN	This Direction Is Not Supported
	SROF	Equipment Does Not Match Request Get IOR Failed
RTRV-PM-VT1	ENEQ	Equipment Not Found Equipment Not Present
	ICNV	Invalid Command Operation not supported by this card
	IDNV	Interval Out Of Range Invalid MONLEV Value Invalid MONTYPE Value
	IIAC	Equipment Does Not Match Request Invalid AID
	IICM	Input, Invalid Command
RTRV-PM-VT1 (continued)	SDBE	Cannot Access Equipment Cannot Access VT Internal Access Failed Internal Database Error VT Not Provisioned
	SNCN	This Direction Is Not Supported
	SROF	Get IOR Failed Operation Not Supported
RTRV-PMMODE-<STS_PATH>	IIAC	Invalid AID
	IICM	Input, Invalid Command
	SDBE	Cannot Access STS Internal Database Error STS Not Provisioned
	SROF	Get IOR Failed
RTRV-PMSCHED-<OCN_TYPE>	IIAC	Invalid AID
	IICM	Input, Invalid Command
	SDBE	Operation not supported by this card Internal Database Error
	SSRE	Memory Resources Exceeded
RTRV-PMSCHED-<STS_TYPE>	IIAC	Invalid AID
	IICM	Input, Invalid Command
	SDBE	Operation not supported by this card Internal Database Error
	SSRE	Memory Resources Exceeded
RTRV-PMSCHED-ALL	IIAC	Invalid AID
	SDBE	Operation not supported by this card Internal Database Error
	SSRE	Memory Resources Exceeded
RTRV-PMSCHED-DS1	IIAC	Invalid AID
	SDBE	Operation not supported by this card Internal Database Error
	SSRE	Memory Resources Exceeded
RTRV-PMSCHED-EC1	IIAC	Invalid AID
	IICM	Input, Invalid Command
	SDBE	Operation not supported by this card Internal Database Error
	SSRE	Memory Resources Exceeded
RTRV-PMSCHED-T1	IIAC	Invalid AID
	SDBE	Operation not supported by this card Internal Database Error
	SSRE	Memory Resources Exceeded
RTRV-PMSCHED-T3	IIAC	Invalid AID
	SDBE	Operation not supported by this card Internal Database Error
	SSRE	Memory Resources Exceeded
RTRV-PMSCHED-VT1	IIAC	Invalid AID
	SDBE	Operation not supported by this card Internal Database Error
	SSRE	Memory Resources Exceeded
RTRV-PROTNSW-<OCN_TYPE>	ENEQ	Equipment Not Found
	IDNC	Invalid Data
	IIAC	Equipment Does Not Match Request Invalid AID
	SDBE	Internal Access Failed Internal Database Error
	SROF	Cannot Access Facility Facility Not Provisioned Get IOR Failed
RTRV-PROTNSW-<STS_TYPE>	ENEQ	Equipment Not Found
	IDNV	Multiple AIDs Not Allowed
	IIAC	Invalid AID Invalid Aid AID Validation Failed Invalid AID
	RRNG	Invalid Slot Number
	SDBE	Cannot Access STS Internal Access Failed Internal Database Error STS Not Provisioned
	SROF	Cannot Access Cross-Connection Get IOR Failed STS Rates Do Not Match
	SSRD	Switch Request Denied
RTRV-PROTNSW-VT1	ENEQ	Equipment Not Found
	ICNV	Invalid Command
	IIAC	Equipment Does Not Match Request Invalid AID
	RRNG	Invalid Slot Number
	SDBE	Internal Access Failed Internal Database Error
	SROF	Cannot Access Cross-Connection Get IOR Failed Requested Operation Failed
	SSRD	Switch Request Denied
RTRV-PTHTRC-<STS_PATH>	ENEQ	Equipment Not Found Equipment Not Present
	IDNV	Multiple AIDs Not Allowed
	IIAC	Invalid AID Invalid Aid Expected Trace Not Supported On This Card Type Incoming Trace Not Supported On This Card Type Invalid AID Trace Not Supported On This Card Type
	IICM	Input, Invalid Command
	IIDT	Invalid Location Value
	RRNG	Invalid Slot Number
	SDBE	Cannot Access STS Internal Data Base Error STS Is Not Provisioned Cannot Access Equipment Cannot Access STS Internal Access Failed Internal Database Error STS Not Provisioned
	SOSE	Unrecognized Message Type
	SROF	Get IOR Failed
RTRV-SYNCN	IIAC	Invalid AID
	SDBE	Internal Data Base Error Internal Database Error
	SROF	Get IOR Failed
RTRV-T1	ENEQ	Equipment Not Found
	ICNV	Invalid Command
	IIAC	Equipment Does Not Match Request Invalid AID Invalid DS1 AID
	IICM	Input, Invalid Command
	IPNV	Invalid Parameter
	SDBE	Cannot Access Object Internal Access Failed Internal Database Error
	SROF	Get IOR Failed
RTRV-T3	ENEQ	Equipment Not Found
	ICNV	Invalid Command
	IIAC	Equipment Does Not Match Request Invalid AID Invalid DS1 AID
	IICM	Input, Invalid Command
	IPNV	Invalid Parameter
	SDBE	Cannot Access Object Internal Access Failed Internal Database Error
	SROF	Get IOR Failed
RTRV-TACC	IDNV	Multiple AIDs Not Allowed
	IIAC	Invalid AID
	SROF	Tap Not Provisioned Tap Number Does Not Exist Unknown Internal Error
RTRV-TH-<OCN_TYPE>	ENEQ	Equipment Not Found
	ICNV	Pm Not Supported Performance Monitoring Type Not Supported
	IDNC	Invalid Data
	IIAC	Equipment Does Not Match Request Invalid AID
	IICM	Input, Invalid Command
	IPNC	Invalid Parameter
	SDBE	Facility Does Not Exist Internal Access Failed Internal Database Error
	SROF	Cannot Access Performance Monitoring Statistics Get IOR Failed
RTRV-TH-<STS_PATH>	ENEQ	Internal Communication Error
	ICNV	Performance Monitoring Type Not Supported
	IIAC	Invalid AID
	IICM	Input, Invalid Command
	IPNV	Far End Performance Monitoring Values Not Supported
	SDBE	Cannot Access STS Internal Database Error STS Not Provisioned
	SROF	Get IOR Failed
RTRV-TH-DS1	ENEQ	Equipment Not Found Equipment Not Provisioned Internal Communication Error
	ICNV	Invalid Command
	IDNV	Incompatible Equipment Type
	IIAC	Equipment Does Not Match Request Invalid AID Invalid DS1 AID
	IICM	Input, Invalid Command
	IPNV	Far End Performance Monitoring Values Not Supported Invalid Parameter PM Not Supported
	SDBE	Cannot Access Object Internal Access Failed Internal Database Error
	SROF	Get IOR Failed
RTRV-TH-EC1	ENEQ	Equipment Not Found
	ICNV	Pm Not Supported Performance Monitoring Type Not Supported
	IDNC	Invalid Data
	IIAC	Equipment Does Not Match Request Invalid AID
	IICM	Input, Invalid Command
	IPNC	Invalid Parameter
	SDBE	Facility Does Not Exist Internal Access Failed Internal Database Error
	SROF	Cannot Access Performance Monitoring Statistics Get IOR Failed
RTRV-TH-T1	ENEQ	Equipment Not Found Equipment Not Provisioned Internal Communication Error
	ICNV	Invalid Command
	IDNV	Incompatible Equipment Type
	IIAC	Invalid AID
	IICM	Input, Invalid Command
	IPNV	Far End Performance Monitoring Values Not Supported Invalid Parameter PM Not Supported
	SDBE	Cannot Access Object Internal Access Failed Internal Database Error
	SROF	Get IOR Failed
RTRV-TH-T3	ENEQ	Equipment Not Found Equipment Not Provisioned Internal Communication Error
	ICNV	Invalid Command
	IDNV	Incompatible Equipment Type
	IIAC	Equipment Does Not Match Request Invalid AID Invalid DS1 AID
	IPNV	Far End Performance Monitoring Values Not Supported Invalid Parameter PM Not Supported
	SDBE	Cannot Access Object Internal Access Failed Internal Database Error
	SROF	Get IOR Failed
RTRV-TH-VT1	ICNV	Invalid Command Operation not supported by this card Performance Monitoring Type Not Supported
	IIAC	Equipment Does Not Match Request Invalid AID
	IICM	Input, Invalid Command
	SDBE	Cannot Access VT Cannot Access VT Performance Monitoring Parameters Internal Database Error VT Not Provisioned
RTRV-TH-VT1 (continued)	SROF	Get IOR Failed Operation Not Supported
RTRV-TOD	SDBE	Cannot Access Date/Time Cannot Access Timezone\ Internal Database Error
	SROF	Get IOR Failed
RTRV-UCP-CC	IICM	Input, Invalid Command
	SDBE	Internal Database Error
	SROF	Get IOR Failed
RTRV-UCP-IF	IICM	Input, Invalid Command
	SDBE	Internal Database Error
	SROF	Get IOR Failed
RTRV-UCP-NBR	IICM	Input, Invalid Command
	SDBE	Internal Database Error
	SROF	Get IOR Failed
RTRV-UCP-NODE	IICM	Input, Invalid Command
	SDBE	Internal Database Error
	SROF	Get UCP Node Interface Failed
RTRV-USER-SECU	IIAC	Invalid AID
	PICC	AID Required Unknown CORBA Exception (Internal Error) Unknown User User Identifier Exceeds Maximum Length Allowed
	PIUC	User Is Not Superuser
	SDBE	Internal Database Error
	SROF	Get IOR Failed
RTRV-VT1	ENEQ	Equipment Not Found
	ICNV	Invalid Command
	IIAC	Equipment Does Not Match Request Invalid AID
	IICM	Input, Invalid Command
	RRNG	Invalid Slot Number
	SDBE	Cannot Access STS Cannot Access VT Internal Access Failed Internal Database Error STS Not Provisioned VT Not Provisioned
RTRV-VT1 (continued)	SROF	Cannot Access Cross-Connection Get IOR Failed
SCHED-PMREPT-<OCN_TYPE>	IDNV	Invalid MONLEV Value Invalid Report Interval Invalid Start Time Number Of Reports Is Negative
	IIAC	Invalid AID
	IICM	Input, Invalid Command
	IIDT	Duplicate Performance Monitoring Schedule Maximum Performance Monitoring Schedule Limit Reached Performance Monitoring Schedule Does Not Exist
	IPNV	Far End Performance Monitoring Values Not Supported
	SDBE	Operation not supported by this card Internal Database Error
	SSRE	Memory Resources Exceeded
SCHED-PMREPT-<STS_PATH>	IDNV	Invalid MONLEV Value Invalid Report Interval Invalid Start Time Number Of Reports Is Negative
	IIAC	Invalid AID
	IICM	Input, Invalid Command
	IIDT	Duplicate Performance Monitoring Schedule Maximum Performance Monitoring Schedule Limit Reached Performance Monitoring Schedule Does Not Exist
	IPNV	Far End Performance Monitoring Values Not Supported
	SDBE	Operation not supported by this card Internal Database Error
	SSRE	Memory Resources Exceeded
SCHED-PMREPT-DS1	IDNV	Invalid MONLEV Value Invalid Report Interval Invalid Start Time Number Of Reports Is Negative
	IIAC	Invalid AID
	IIDT	Duplicate Performance Monitoring Schedule Maximum Performance Monitoring Schedule Limit Reached Performance Monitoring Schedule Does Not Exist
	IPNV	Far End Performance Monitoring Values Not Supported
SCHED-PMREPT-DS1 (continued)	SDBE	Operation not supported by this card Internal Database Error
	SSRE	Memory Resources Exceeded
SCHED-PMREPT-EC1	IDNV	Invalid MONLEV Value Invalid Report Interval Invalid Start Time Number Of Reports Is Negative
	IIAC	Invalid AID
	IICM	Input, Invalid Command
	IIDT	Duplicate Performance Monitoring Schedule Maximum Performance Monitoring Schedule Limit Reached Performance Monitoring Schedule Does Not Exist
	IPNV	Far End Performance Monitoring Values Not Supported
	SDBE	Operation not supported by this card Internal Database Error
	SSRE	Memory Resources Exceeded
SCHED-PMREPT-T1	IDNV	Invalid MONLEV Value Invalid Report Interval Invalid Start Time Number Of Reports Is Negative
	IIAC	Invalid AID
	IIDT	Duplicate Performance Monitoring Schedule Maximum Performance Monitoring Schedule Limit Reached Performance Monitoring Schedule Does Not Exist
	IPNV	Far End Performance Monitoring Values Not Supported
	SDBE	Operation not supported by this card Internal Database Error
	SSRE	Memory Resources Exceeded
SCHED-PMREPT-T3	IDNV	Invalid MONLEV Value Invalid Report Interval Invalid Start Time Number Of Reports Is Negative
	IIAC	Invalid AID
	IIDT	Duplicate Performance Monitoring Schedule Maximum Performance Monitoring Schedule Limit Reached Performance Monitoring Schedule Does Not Exist
	IPNV	Far End Performance Monitoring Values Not Supported
SCHED-PMREPT-T3 (continued)	SDBE	Operation not supported by this card Internal Database Error
	SSRE	Memory Resources Exceeded
SCHED-PMREPT-VT1	IDNV	Invalid MONLEV Value Invalid Report Interval Invalid Start Time Number Of Reports Is Negative
	IIAC	Invalid AID
	IIDT	Duplicate Performance Monitoring Schedule Maximum Performance Monitoring Schedule Limit Reached Performance Monitoring Schedule Does Not Exist
	IPNV	Far End Performance Monitoring Values Not Supported
	SDBE	Operation not supported by this card Internal Database Error
	SSRE	Memory Resources Exceeded
SET-ATTR-CONT	IIAC	Invalid AID
	SDBE	Cannot Access Controls Internal Database Error
	SROF	Get IOR Failed
	SRQN	Invalid Request
SET-ATTR-ENV	IIAC	Invalid AID
	IPNC	Description Cannot Have More Than 64 Characters
	IPNV	Invalid Parameter
	SDBE	Cannot Access Environmental Settings Internal Database Error
	SROF	Get IOR Failed
	SRQN	Invalid Request
SET-PMMODE-<STS_PATH>	IICM	Input, Invalid Command
	ENEQ	Equipment Not Found
	ICNV	Pm Not Supported Performance Monitoring Type Not Supported
	IDNC	Invalid Data
	IDRG	Invalid Threshold Value
	IIAC	Equipment Does Not Match Request Invalid AID
	IICM	Input, Invalid Command
	IPNV	Invalid Parameter
SET-PMMODE-<STS_PATH> (continued)	SDBE	Facility Does Not Exist Facility Does Not Match Request Internal Access Failed Internal Database Error
	SROF	Cannot Access Performance Monitoring Statistics Get IOR Failed
SET-TH-<OCN_TYPE>	ICNV	Pm Not Supported Performance Monitoring Type Not Supported
	ENEQ	Equipment Not Found
	SROF	Cannot Access Performance Monitoring Statistics Get IOR Failed
	IICM	Input, Invalid Command
	IPNV	Invalid Parameter
	SDBE	Facility Does Not Exist Facility Does Not Match Request Internal Access Failed Internal Database Error
	IDNC	Invalid Data
	IDRG	Invalid Threshold Value
	IIAC	Equipment Does Not Match Request Invalid AID
SET-TH-<STS_PATH>	ENEQ	Internal Communication Error
	ICNV	Performance Monitoring Type Not Supported
	IDRG	Invalid Threshold Value
	IIAC	Cannot Make Changes To Protect Card Invalid AID
	IICM	Input, Invalid Command
	IPNV	Far End Performance Monitoring Values Not Supported
	SDBE	Cannot Access STS Internal Database Error STS Not Provisioned
	SROF	Cannot Access Performance Monitoring Statistics Get IOR Failed
SET-TH-DS1	ENEQ	Equipment Not Found Equipment Not Provisioned Internal Communication Error
	ICNV	Invalid Command
	IDNV	Incompatible Equipment Type
	IDRG	Threshold Out Of Range
SET-TH-DS1 (continued)	IIAC	Cannot Make Changes To Protect Card Equipment Does Not Match Request Invalid AID Invalid DS1 AID
	IICM	Input, Invalid Command
	IPNV	Invalid Parameter PM Not Supported
	SDBE	Cannot Access Object Internal Access Failed Internal Database Error
	SROF	Get IOR Failed
SET-TH-EC1	ENEQ	Equipment Not Found
	ICNV	Pm Not Supported Performance Monitoring Type Not Supported
	IDNC	Invalid Data
	IDRG	Invalid Threshold Value
	IIAC	Equipment Does Not Match Request Invalid AID
	IICM	Input, Invalid Command
	IPNV	Invalid Parameter
	SDBE	Facility Does Not Exist Facility Does Not Match Request Internal Access Failed Internal Database Error
	SROF	Cannot Access Performance Monitoring Statistics Get IOR Failed
SET-TH-T1	ENEQ	Equipment Not Found Equipment Not Provisioned Internal Communication Error
	ICNV	Invalid Command
	IDNV	Incompatible Equipment Type
	IDRG	Threshold Out Of Range
	IIAC	Cannot Make Changes To Protect Card Equipment Does Not Match Request Invalid AID Invalid DS1 AID
	IICM	Input, Invalid Command
	IPNV	Invalid Parameter PM Not Supported
	SDBE	Cannot Access Object Internal Access Failed Internal Database Error
SET-TH-T1 (continued)	SROF	Get IOR Failed
SET-TH-T3	ENEQ	Equipment Not Found Equipment Not Provisioned Internal Communication Error
	ICNV	Invalid Command
	IDNV	Incompatible Equipment Type
	IDRG	Threshold Out Of Range
	IIAC	Cannot Make Changes To Protect Card Equipment Does Not Match Request Invalid AID Invalid DS1 AID
	IICM	Input, Invalid Command
	IPNV	Invalid Parameter PM Not Supported
	SDBE	Cannot Access Object Internal Access Failed Internal Database Error
	SROF	Get IOR Failed
SET-TH-VT1	ICNV	Invalid Command Operation not supported by this card Performance Monitoring Type Not Supported
	IIAC	Cannot Make Changes To Protect Card Equipment Does Not Match Request Invalid AID
	IICM	Input, Invalid Command
	IPNV	Invalid Parameter
	SDBE	Cannot Access VT Cannot Access VT Performance Monitoring Parameters Internal Database Error VT Not Provisioned
	SROF	Get IOR Failed Operation Not Supported
SET-TOD	IDRG	Difference Value Range Error
	IIAC	Invalid Month Or Day Invalid Time Invalid Year
	SDBE	Cannot Access Date/Time Cannot Access Timezone Cannot Set Date Cannot Set Date When Using SNTP Cannot Set Timezone Internal Database Error
SET-TOD (continued)	SROF	Get IOR Failed
SW-DX-EQPT	ENEQ	Equipment Not Found
	IIAC	Invalid AID
	IICM	Input, Invalid Command
	SDBE	Internal Access Failed Internal Database Error
	SROF	Get IOR Failed
	SRQN	Invalid Request
SW-TOPROTN-EQPT	ENEQ	Equipment Not Found
	IDNV	Input, Data Not Valid Invalid Protid
	IIAC	Input, Invalid Access Invalid AID
	IICM	Input, Invalid Command
	SAAL	Already Allowed
	SDBE	Cannot Access Protection Group Internal Access Failed Internal Database Error
	SNVS	Protection Group Does Not Exist Working Unit Already Active Working Unit Already Standby
	SROF	Cannot Access Protection Group Information Cannot Access Protection Group Name Get IOR Failed
	SRQN	Invalid Request
SW-TOWKG-EQPT	ENEQ	Equipment Not Found
	IDNV	Input, Data Not Valid Invalid Protid
	IIAC	Input, Invalid Access Invalid AID
	IICM	Input, Invalid Command
	SAAL	Already Allowed
	SDBE	Cannot Access Protection Group Internal Access Failed Internal Database Error
	SNVS	Protection Group Does Not Exist Working Unit Already Active Working Unit Already Standby
SW-TOWKG-EQPT (continued)	SROF	Cannot Access Protection Group Information Cannot Access Protection Group Name Get IOR Failed
	SRQN	Invalid Request

7.3 Echo

In order to improve telnet functionality for automated systems, the echo function has been turned off since ONS 15454 Release 3.0. This change is transparent to users running standard UNIX-compliant telnet clients; however, PC users may need to change their client setup to enable "local echo." This is normally accomplished by a pull-down menu or a preference attribute.

To test the local echo on your PC client, use the RTRV-HDR command. If you receive a response but no data, set local echo ON. Cisco recommends that you close any windows containing sensitive information after exiting a TL1 session.

Table Of Contents

TL1 Alarms and Errors