cc/td/doc/product/ong/15302
hometocprevnextglossaryfeedbacksearchhelp
PDF

Table Of Contents

ONSCLI Command Hierarchy

8.1  Menu Tree

8.1.1  General Commands

8.1.2  Device Commands

8.1.3  Ports Commands

8.1.4  Bridge Commands

8.1.5  Security Commands

8.1.6  Statistics Commands

8.1.7  Services and Alarms Commands


ONSCLI Command Hierarchy


The complete ONSCLI command Hierarchy for ONS 15302 shown in this chapter.


Tip Each basic command is shaded, and is marked by a number that refers to the appropriate line in the parameter description table, Table 8-1.



Note Blank columns in the parameter description table are reserved for future commands with their parameters.


The complete names of both commands and parameter keywords are shown in Table 8-1. Optional parameters are enclosed in square brackets. For clarity, parameter command keywords are written in capital letters, and lengthy commands are shown on several lines.

The order of parameters (keyword and value pairs) is not significant. The help command ? will display all available commands at the current level, each with a short description.

8.1  Menu Tree

This section displays all available commands of the ONS 15302 in a graphical version and it also describes the following main commands and sub commands:

General Commands

Device

Ports

Bridge

Security

Statistics

Services

Alarms

8.1.1  General Commands

General commands are shown in Figure 8-1.

Figure 8-1

General Commands - ONSCLI

8.1.2  Device Commands

Device commands are shown in Figure 8-2.

Figure 8-2

Device commands - ONSCLI

Management Configuration commands are shown in Figure 8-3.

Figure 8-3

Management Configuration commands - ONSCLI

System Mode IP commands are shown in Figure 8-4.

Figure 8-4 System Mode IP - ONSCLI

System Mode IP Unnumbered are shown in Figure 8-5.

Figure 8-5

System Mode IP Unnumbered commands - ONSCLI

DCN Router commands are shown in Figure 8-6.

Figure 8-6

DCN Router commands - ONSCLI

OSI Configuration commands are shown in Figure 8-7.

Figure 8-7

OSI Configuration commands - ONSCLI

VLAN commands are shown in Figure 8-8.

Figure 8-8 VLAN commands - ONSCLI

8.1.3  Ports Commands

Ports commands are shown in Figure 8-9.

Figure 8-9 Ports commands - ONSCLI

Ethernet- and WAN ports commands are shown in Figure 8-10.

Figure 8-10 Ethernet- and WAN ports commands - ONSCLI

WANX and Tributary port commands are shown in Figure 8-11.

Figure 8-11 WANX and Trib port commands - ONSCLI

Aggregate ports commands are shown in Figure 8-12.

Figure 8-12 Aggregate ports commands - ONSCLI

8.1.4  Bridge Commands

Bridge commands are shown in Figure 8-13.

Figure 8-13 Bridge commands - ONSCLI

Multicast, IGMP Snooping and Traffic Control commands are shown in Figure 8-14.

Figure 8-14 Multicast, IGMP Snooping and Traffic Control commands - ONSCLI

Router commands are shown in Figure 8-15.

Figure 8-15 Router commands - ONSCLI

IP Router command are shown in Figure 8-16.

Figure 8-16 IP Router commands - ONSCLI

RIP commands are shown in Figure 8-17.

Figure 8-17 RIP commands - ONSCLI

OSPF commands are shown in Figure 8-18.

Figure 8-18 OSPF commands - ONSCLI

DHCP commands are shown in Figure 8-19.

Figure 8-19 DHCP commands - ONSCLI

IPX commands are shown in Figure 8-20.

Figure 8-20 IPX commands - ONSCLI

RIP-SAP Filters commands are shown in Figure 8-21.

Figure 8-21 RIP-SAP Filters commands - ONSCLI

IPM commands are shown in Figure 8-22.

Figure 8-22 IPM commands - ONSCLI

8.1.5  Security Commands

Security commands are shown in Figure 8-23.

Figure 8-23

Security commands - ONSCLI

8.1.6  Statistics Commands

Statistics commands are shown in Figure 8-24.

Figure 8-24

Statistics commands - ONSCLI

8.1.7  Services and Alarms Commands

Service and Alarms commands are shown in Figure 8-25.

Figure 8-25

Service and Alarms commands - ONSCLI

QoS commands are shown in Figure 8-26.

Figure 8-26

QoS commands - ONSCLI

Table 8-1 ONS 15302 - ONSCLI Command and Parameters 

Command
Parameters

1.

IP-ConfigurationRouter

[IP-ADDRESS=<IP address>] [SUBNET-MASK=<IP address>]

2.

IP-Configuration

[IP-ADDRESS=<IP address>] [SUBNET-MASK=<IP address>] [DEFAULT-GATEWAY=<IP address>]

3.

MAC-Filter

[MAC-FILTER-SWITCH=<enabled | disabled>]

4.

System-Id

[SYSTEM-ID=<NSAP system ID - hexString[2:16]>] [NSEL=<NSAP selector - hexString[2:2]>]

5.

Show

<none>

6.

Add

AREA-ADDRESS=<NSAP area address - hexString[4:36]>

7.

Edit

INDEX=<integer value 1:3> AREA-ADDRESS=<NSAP area address - hexString[4:36]>

8.

Remove

INDEX=<integer value 1:3>

9.

ModeOsi

MODE=<notUsed|ip|clnp|ipAndClnp>>

10.

Gateway-Configuration

[NSAP-ADDRESS=<NSAP address - hexString[6:40]>] [STATUS=<enabled|disabled>]

11.

LAPD-Configuration

[LAPD-ROLE=<network|user>][TOGGLE-CR=<enabled|disabled>][N201=<integer value 0:65535>]

12.

OSI-IP-ConfigurationRouter

[OSI-IP-ADDRESS=<IP address>] [OSI-SUBNET-MASK=<IP address>]

13.

DccIpNonOsiMode

[MODE=<notUsed|ipBroadcast|ipRouting|ipPppCrc16|ipPppCrc32>]

14.

IP-Configuration

[IP-ADDRESS=<IP address>] [SUBNET-MASK=<IP address>]

15.

ManModeOsi

[[MODE=<notUsed|ip|clnp|ipAndClnp>]

16.

ManModeNonOsi

[[MODE=<notUsed|ip|>]

17.

ManModeIpun

[MODE=<notUsed|ip>]

18.

OSI-IP-ConfigurationBridge

[OSI-IP-ADDRESS=<IP address>] [OSI-SUBNET-MASK=<IP address>] [OSI-DEFAULT-GATEWAY=<IP address>]

19.

OsiMode

[MODE=<notUsed|ip|clnp|ipAndClnp>]

20.

DccModeIpun

[[MODE=<notUsed|ipPppCrc16|ipPppCrc32>]

21.

DccIpOsiMode

[MODE=<notUsed|ipBroadcas|ipRouting|osiEncapsulation|ipPppCrc16|ipPppCrc32>]

22.

DccIpNonOsiMode

[MODE=<notUsed|ipBroadcast|ipRouting|ipPppCrc16|ipPppCrc32>]

23.

Add

IP-ADDRESS=<IP address> IF-NUM=<integer value> SUBNET-MASK=<IP address> [DEFAULT-GATEWAY=<IP address>]

24.

Edit

IP-ADDRESS=<IP address> [IF-INDEX=<integer value>] [SUBNET-MASK=<IP address>] [DEFAULT-GATEWAY=<IP address>]

25.

Remove

IP-ADDRESS=<IP address>

26.

Show

IP-ADDRESS=<IP address>

27.

PPP-IP-Routing

[IP-ADDRESS=<IP address>][SUBNET-MASK=<IP address>]

28.

PPP-IP-Routing

[IP-ADDRESS=<IP address>] [SUBNET-MASK=<IP address>] [DEFAULT-GATEWAY=<IP address>]

29.

Encapsulation

[HELLO-INTERVAL=<integer value 0:65535>]

30.

General

[L1-LSP=<integer value 0:1492>][L2-LSP=<integer value 0:1492>][IS-MODE=<disabled|is|l1Is|l2Is>]

31.

Identification

[NAME=<string[0:160]>] [LOCATION=<string[0:160]>] [CONTACT=<string[0:160]>]

32.

Time

[TIME=<hh:mm:ss>] [DATE=<yyyy-mm-dd>]

33.

Time-Protocol

[SERVER-IP-ADDRESS=<IP address>] [SYNC-INTERVAL=<integer value 0:2147483647>] [UTC-DELTA=<integer value -720:720>]

34.

FFT

[IP-FASTFORWARDING=<enable|disable>] [IPX-FASTFORWARDING=<enable|disable>]

35.

Autodiscovery

[STATUS=<enabled|disabled>] [TRAP-FREQUENCY=<integer value 0:2147483647>]

36.

Show

<none>

37.

Replace-Licence-Key

LICENCE-KEY=<string[1:50]>

38.

Show

[VLAN-NUMBER=<integer>]

39.

Add

NAME=<string> [ADDRESS-TYPE=<default|reserve>] [TAG=<integer>]

40.

Edit

VLAN-NUMBER=<integer> [NAME=<string>] [ADDRESS-TYPE=<default|reserve>] [TAG=<integer>]

41.

Remove

VLAN-NUMBER=<integer>

42.

Show

[VLAN-NUMBER=<integer>]

43.

Add

VLAN-NUMBER=<integer> ETHERNET-PORTS=<portList> [TAGGING=<enable|disable>]

44.

Edit

VLAN-NUMBER=<integer> ETHERNET-PORTS =<portList> TAGGING=<enable|disable>

45.

Remove

VLAN-NUMBER=<integer> ETHERNET-PORTS =<portList>

46.

Sync-Source

[ADMIN-SOURCE=<Trib1|Trib2|Trib3|Trib4|Trib5|Trib6|Trib7|Trib8|Trib9|Trib10| Trib11|Trib12|Aggr1|Aggr2|Active|Local|External>]

47.

Inventory

<none>

48.

Remote-Device-Identification

[REMOTE-DEVICE=<IP address>]

49.

Main

[ETHERNET-PORT=<integer value 1:8>] [SPEED-ADMIN-MODE=<10M|100M>] [ADMINISTRATIVE-STATUS=<on|off>] [DESCRIPTION=<string[0:64]>] [DUPLEX-ADMIN-MODE=<none|half|full>] [PHYSICAL-ADDRESS-ASSIGNMENT=<default|reserve>][AUTONEGOTIATION-MODE=<enabled|disabled>]

50.

Other

[ETHERNET-PORT=<integer value 1:8>] [BACK-PRESSURE-MODE=<enable|disable>][FLOW-CONTROL-MODE=<on|off|autoNegotiation>]

51.

VLAN-Properties

[ETHERNET-PORT=<integer value 1:8>]

52.

IP-Properties

[ETHERNET-PORT=<integer value 1:8>]

53.

IPX-Properties

[ETHERNET-PORT=<integer value 1:8>]

54.

Reset-Device

<none>

55.

Erase-Configuration

<none>

56.

Erase-NVRAM

<none>

57.

Tributary-Port-Properties

[TRIBUTARY-PORT=<port>] [DESCRIPTION=<string>] [ADMINISTRATIVE-STATUS=<enable|disable>] [MODE=<TRA|PRA>] [LOOP-MODE=<NONE|LL2|LL3>] [PATH-TRACE=<enabled|disabled>] [EXPECTED-TI=<string>] [TRANSMIT-TI=<string>] [MONITORING-STATUS=<ENABLED|DISABLED>]

58.

General

AGGREGATE-PORT=<integer value 1:2> [ADMINISTRATIVE-STATUS=<enable|disable>] [DESCRIPTION=<string[0:64]>] [CONNECTED-TO=<string[0:160]>]

59.

Protection

[MSP-STATUS=<enabled|disabled>] [PROTECTION-TYPE=<unidirectional|bidirectional>] [REVERTING-STATUS=<enabled|disabled>] [WAIT-TO-RESTORE-TIME=<integer>][SWITCHING-COMMAND=<clear|exercise|manualSwitchToProtecting|manualSwitchToWorking| forcedSwitchToProtecting|forcedSwitchToWorking|lockoutProtection>]

60.

VC4-Path-Trace

[PATH-TRACE=<enabled|disabled>] [EXPECTED-TI=<string[1:15]>] [HEX-EXPECTED-TI=<string[2:44]>][TRANSMIT-TI=<string[1:15]>] [HEX-TRANSMIT-TI=<string[2:44]>]

61.

RS-Path-Trace

AGGREGATE-PORT=<integer value 1:2> [PATH-TRACE=<enabled|disabled>] [EXPECTED-TI=<string[1:15]>][HEX-EXPECTED-TI=<string[2:44]>] [TRANSMIT-TI=<string[1:15]>] [HEX-TRANSMIT-TI=<string[2:44]>]

62.

Alarm-Port-Properties

[ALARM-PORT=<integer value 1:4>] [MODE=<enabled|disabled>] [DESCRIPTION=<string[0:64]>] [TRIGGERED-WHEN=<opens|closes>]

63.

User-Channel-Port-Properties

[ADMINISTRATIVE-STATUS=<enabled|disabled>] [DESCRIPTION=<string[0:64]>] [AGGREGATE-PORT=<SDH-A|SDH-B|ACTIVE>] [DATA-RATE=<sync64000|async19200>]

64.

Operating-Parameters

[FORWARDING-TABLE-AGING-TIME=<integer value 10:1000000>][BRIDGE-MODE=<normal|provider>]

65.

VLAN-Id-Table

ETHERNET-PORT=<integer value 1:8>

66.

Show

<none>

67.

Add

VLAN-TAG-ID=<integer value 1:4000>MAC-ADDRESS=<MAC address - hexString[12:12]>ETHERNET-PORT=<integer value 1:8>[STATUS=<permanent|deleteOnReset>]

68.

Edit

VLAN-TAG-ID=<integer value 1:4000>MAC-ADDRESS=<MAC address - hexString[12:12]>ETHERNET-PORT=<integer value 1:8>[STATUS=<permanent|deleteOnReset>]

69.

Remove

VLAN-TAG-ID=<integer value 1:4000>MAC-ADDRESS=<MAC address - hexString[12:12]>ETHERNET-PORT=<integer value 1:8>

70.

Size-Unicast-Global-Forwarding-Table

<none>

71.

Factory-Reset

<none>

72.

Show

[IP-ADDRESS=<IP address>]

73.

General

[WAN-PORT=<integer value 5:8>] [PATH-TRACE=<enabled|disabled>][EXPECTED-TI=<string[1:15]>][HEX-EXPECTED-TI=<string[2:44]>][TRANSMIT-TI=<string[1:15]>][HEX-TRANSMIT-TI=<string[2:44]>][CHANNEL-TI=<integer value 0:50>]

74.

Add-VC12-channel

WAN-PORT=<integer value 5:8> [KLM=<K.L.M - integer value 1:3.integer value 1:7.integer value 1:3>][ADMIN-STATUS=<enabled|disabled>] [NUMBER-TO-ADD=<integer value 1:50>] [SORT-MODE=<LEX|G707>]

75.

Edit-VC12-channel

[WAN-PORT=<integer value 5:8>] [WAN-CHANNEL=<integer value 1:50>] [ADMIN-STATUS=<enabled|disabled>]

76.

Remove-VC12-channel

WAN-PORT=<integer value 5:8> [NUMBER-TO-REMOVE=<integer value 1:50>]

77.

General

[[TRIB-PORT=<integer value 1:12>] [DESCRIPTION=<string[0:64]>] [ADMINISTRATIVE-STATUS=<enable|disable>][MODE=<TRA|PRA>] [LOOP-MODE=<NONE|LL2|LL3>][PATH-TRACE=<enabled|disabled>] [EXPECTED-TI=<string[1:15]>] [HEX-EXPECTED-TI=<string[2:44]>][TRANSMIT-TI=<string[1:15]>] [HEX-TRANSMIT-TI=<string[2:44]>]

78.

Assign-VC12-Channel

TRIB-PORT=<integer value 1:12> [KLM=<K.L.M - integer value 1:3.integer value 1:7.integer value 1:3>][NUMBER-TO-ADD=<integer value 1:12>] [SORT-MODE=<LEX|G707>]

79.

Deassign-VC12-Channel

TRIB-PORT=<integer value 1:12> [NUMBER-TO-REMOVE=<integer value 1:12>]

80.

Parameters

[MULTICASTING-ENABLE=<true|false>]

81.

Forwarding-Table

[[VLAN-TAG-ID=<integer value 1:4000>] [MULTICAST-ADDRESS=<MAC address - hexString[12:12]>]

82.

Show

[[VLAN-TAG-ID=<integer value 0:8>]

83.

Edit

[VLAN-TAG-ID=<integer value 1:4000> [STATIC-PORTS=<integer value 0:8,...>] [FORBIDDEN-PORTS=<integer value 0:8,...>]

84.

Show

[[VLAN-TAG-ID=<integer value 1:4000>]

85.

Edit

[VLAN-TAG-ID=<integer value 1:4000> [STATIC-PORTS=<integer value 0:8,...>] [FORBIDDEN-PORTS=<integer value 0:8,...>]

86.

Show

[[VLAN-TAG-ID=<integer value 1:4000>] [MULTICAST-ADDRESS=<MAC address - hexString[12:12]>]

87.

Add

[VLAN-TAG-ID=<integer value 1:4000> MULTICAST-ADDRESS=<MAC address - hexString[12:12]> [EGRESS-PORTS=<integer value 0:8,...>] [FORBIDDEN-PORTS=<integer value 0:8,...>][STATUS=<other|invalid|permanent|deleteOnReset|deleteOnTimeout>]

88.

Edit

[VLAN-TAG-ID=<integer value 1:4000> MULTICAST-ADDRESS=<MAC address - hexString[12:12]>[EGRESS-PORTS=<integer value 0:8,...>] [FORBIDDEN-PORTS=<integer value 0:8,...>][STATUS=<other|invalid|permanent|deleteOnReset|deleteOnTimeout>]

89.

Remove

[VLAN-TAG-ID=<integer value 1:4000> MULTICAST-ADDRESS=<MAC address - hexString[12:12]>

90.

Parameters

[IGMP-ENABLE=<true|false>] [HOST-AGING-TIME-IGMP=<integer value>] [ROUTER-AGING-TIME-IGMP=<integer value>]

91.

Group-Table

[VLAN-TAG-ID =<integer value 1:4000>] [PORT=<integer value 1:8>] [MULTICAST-ADDRESS=<MAC address - hexString[12:12]>]

92.

Router-Table

[VLAN-TAG-ID =<integer value 1:4000>] [PORT=<integer value 1:8>]

93.

Show

[PORT=<integer value 1:8>] [TYPE-OF-PROTOCOL=<notUsed|preDefined|ethUserDefined|llcUserDefined>][PROTOCOL=<NotUsed|Other|IP|RESERVED|IPX_RAW|IPX_Ethernet|IPX_LLC|IPX_SNAP| DECNET|DECLAT|NETBIOS|APPLETALK|XNS|SNA>]

94.

Edit

PORT=<integer value 1:8> TYPE-OF-PROTOCOL=<notUsed|preDefined|ethUserDefined|llcUserDefined>PROTOCOL=<NotUsed|Other|IP|RESERVED|IPX_RAW|IPX_Ethernet|IPX_LLC|IPX_SNAP| DECNET|DECLAT|NETBIOS|APPLETALK|XNS|SNA>[DEFAULT-PRIOR=<integer value 0:7>] [TRAFFIC-CLASSES=<integer value 1:8>]

95.

Show

[PORT=<integer value 1:8>]

96.

Edit

PORT=<integer value 1:8>[DEFAULT-PRIOR=<integer value 0:7>]

97.

Priority-Group-Table

[PORT=<integer value 1:8>]

98.

Port-Table

[VLAN-TAG=<integer value 1:4000>] [ETHERNET-PORT=<integer value 1:8>] [STATUS=<true|false>]

99.

Forced-SW-Version-Table

[VLAN-TAG=<integer value 1:4000>] [STATE=<STPCompatibility|NormalRSTP>]

100.

Add

UDP-DEST-PORT=<integer value> SOURCE-IP-ADDRESS=<IP address> DEST-IP-ADDRESS=<IP address>

101.

Remove

UDP-DEST-PORT=<integer value> SOURCE-IP-ADDRESS=<IP address> DEST-IP-ADDRESS=<IP address>

102.

Remove

LOCAL-IP-ADDR=<IP address> LOCAL-PORT=<integer value 0:65535> REMOTE-IP-ADDR=<IP address>REMOTE-PORT=<integer value 0:65535>

103.

IPM- Tuning

[FFT-ENTRIES-AFTER-RESET=<integer value>] [NEIGBOUR-ENTRIES-AFTER-RESET=<integer value>][ROUTE-ENTRIES-AFTER-RESET=<integer value>] [INTERFACE-ENTRIES-AFTER-RESET=<integer value>][IGMP-ENTRIES-AFTER-RESET=<integer value>]

104.

Global-Parameters

[POLICY-ENABLE=<true|false>]

105.

Show

[INDEX=<integer value 1:256>] [DETAILED=<False|True>]

106.

Add

[DESCRIPTION=<string[0:40]>] PROFILE-TYPE=<minBandwidth|bandwidthGuarantee|minDelay|minDelayPerSession>RATE(Kbps)=<integer value> [MAX-SESSION=<integer value>] [NEW-TOS-OR-DSCP=<integer value 0:255>][CHANGE-TOS-OR-DSCP=<true|false>] [BURST-SIZE=<integer value>] [NEW-VPT=<integer value 0:7>]

107.

Edit

INDEX=<integer value 1:256> [DESCRIPTION=<string[0:40]>][PROFILE-TYPE=<minBandwidth|bandwidthGuarantee|minDelay|minDelayPerSession>][RATE(Kbps)=<integer value>] [MAX-SESSION=<integer value>] [NEW-TOS-OR-DSCP=<integer value 0:255>][CHANGE-TOS-OR-DSCP=<true|false>] [BURST-SIZE=<integer value>] [NEW-VPT=<integer value 0:7>]

108.

Remove

INDEX=<integer value 1:256>

109.

Classification-Table

[TOS=<true|false>] [PROTOCOL=<true|false>] [SRC-IP-BIT-MASK=<integer value 0:32>] [DST-IP-BIT-MASK=<integer value 0:32>] [SOURCE-PORT-PROTOCOL=<true|false>] [DESTINATION-PORT-PROTOCOL=<true|false>] [INPUT-PORTS=<true|false>]

110.

Remove

INDEX=<integer value>

111.

Add

INDEX=<integer value> [DESCRIPTION=<string[0:40]>] [TOS=<integer value 0:255>] [PROTOCOL=<NotDefined|TCP|UDP>] [SRC-IP=<IP address>] [SRC-MASK=<integer value 0:32>] [DST-IP=<IP address>] [DST-MASK=<integer value 0:32>] [SRC-PORT=<integer value 0:65535>] [DST-PORT=<integer value 0:65535>] [CONDITION=<equal|notEqual|bigger|smaller>] [IN-PORT=<integer value 0:8,...>] [ACTION=<block|blockAndTrap|permit>] [PROFILE-POINTER=<integer value 1:256>] [OUT-PORT=<integer value 0:8,...>] [STATUS=<Active|NotActive>]

112.

Edit

INDEX=<integer value> [DESCRIPTION=<string[0:40]>] [TOS=<integer value 0:255>] [PROTOCOL=<NotDefined|TCP|UDP>] [SRC-IP=<IP address>] [SRC-MASK=<integer value 0:32>] [DST-IP=<IP address>] [DST-MASK=<integer value 0:32>] [SRC-PORT=<integer value 0:65535>] [DST-PORT=<integer value 0:65535>] [CONDITION=<equal|notEqual|bigger|smaller>] [IN-PORT=<integer value 0:8,...>] [ACTION=<block|blockAndTrap|permit>] [PROFILE-INDEX=<integer value 1:256>] [OUT-PORT=<integer value 0:8,...>] [STATUS=<Active|NotActive>]

113.

Move

INDEX=<integer value> NEW-INDEX=<integer value>

114.

Show

[INDEX=<integer value>] [DETAILED=<False|True>]

115.

Show

[INDEX=<integer value 1:256>] [DETAILED=<False|True>]

116.

Add

[DESCRIPTION=<string[0:40]>] PROFILE-TYPE=<minBandwidth|bandwidthGuarantee> RATE(Kbps)=<integer value> [BURST-SIZE=<integer value>] [NEW-VPT=<integer value 0:7>]

117.

Edit

INDEX=<integer value 1:256> [DESCRIPTION=<string[0:40]>] [PROFILE-TYPE=<minBandwidth|bandwidthGuarantee>] [RATE(Kbps)=<integer value>][BURST-SIZE=<integer value>] [NEW-VPT=<integer value 0:7>]

118.

Remove

INDEX=<integer value 1:256>

119.

Remove

INDEX=<integer value>

120.

Add

INDEX=<integer value> IN-PORT=<integer value 0:8,...> OUT-PORT=<integer value 0:8,...> [DESCRIPTION=<string[0:40]>] [ACTION=<block|blockAndTrap|permit>] [PROFILE-INDEX=<integer value 1:256>][STATUS=<Active|NotActive>]

121.

Edit

INDEX=<integer value> [DESCRIPTION=<string[0:40]>] [IN-PORT=<integer value 0:8,...>] [ACTION=<block|blockAndTrap|permit>] [PROFILE-INDEX=<integer value 1:256>] [OUT-PORT=<integer value 0:8,...>] [STATUS=<Active|NotActive>]

122.

Move

INDEX=<integer value> NEW-INDEX=<integer value>

123.

Show

[INDEX=<integer value>] [DETAILED=<False|True>]

124.

Parameters

[VLAN-SUPPORTED-TYPE-AFTER-RESET=<perPort|perProtAndPort>]

125.

Show

[IF-INDEX.=<integer value>]

126.

Add

NAME=<string[0:20]> [ADDRESS-TYPE=<default|reserve>] [TAG=<integer value 1:4000>]

127.

Edit

IF-INDEX=<integer value> [NAME=<string[0:20]>] [ADDRESS-TYPE=<default|reserve>]

128.

Remove

IF-INDEX=<integer value>

129.

Show

[IF-INDEX=<integer value>]

130.

Add

IF-INDEX=<integer value> ETHERNET-PORTS=<integer value 1:8,...> [TAGGING=<enable|disable>][EGRESS-FORBIDDEN=<true|false>]

131.

Edit

IF-INDEX=<integer value> ETHERNET-PORTS=<integer value 1:8,...> [TAGGING=<enable|disable>][EGRESS-FORBIDDEN=<true|false>]

132.

Remove

IF-INDEX=<integer value> ETHERNET-PORTS=<integer value 1:8,...>

133.

Show

[INDEX=<integer value>]

134.

Add

PROTOCOL-NAME=<string[0:20]> PROTOCOL-NUM=<string[4:4]> [PROTOCOL-MASK=<string[4:4]>]

135.

Edit

INDEX=<integer value> [PROTOCOL-NAME=<string[0:20]>] [PROTOCOL-NUM=<string[4:4]>] [PROTOCOL-MASK=<string[4:4]>]

136.

Remove

INDEX=<integer value>

137.

Show

[VLAN-IF-INDEX.=<integer value>]

138.

Add

TYPE-OF-PROTOCOL=<preDefined_protocols|ethUserDefined_protocols> NAME=<string[0:20]>[PROTOCOL=< |Other|IP|IPX_RAW|IPX_Ethernet|IPX_LLC|IPX_SNAP|DECNET|NETBIOS|SNA>][ADDRESS-TYPE=<default|reserve>] [TAG=<integer value 1:4000>]If TYPE-OF-PROTOCOL = ethUserDefined_protocols, PROTOCOL input not needed(taken from vlanEthUserDefProtEntry)

139.

Edit

VLAN-IF-INDEX.=<integer value> [NAME=<string[0:20]>] [ADDRESS-TYPE=<default|reserve>]

140.

Remove

VLAN-NUMBER=<integer value>

141.

Show

[VLAN-NUMBER=<integer value>]

142.

Add

VLAN-NUMBER=<integer value> ETHERNET-PORTS=<integer value 1:8,...> [TAGGING=<enable|disable>][EGRESS-FORBIDDEN=<true|false>]

143.

Edit

VLAN-NUMBER=<integer value> ETHERNET-PORTS=<integer value 1:8,...> [TAGGING=<enable|disable>][EGRESS-FORBIDDEN=<true|false>]

144.

Remove

VLAN-NUMBER=<integer value> ETHERNET-PORTS=<integer value 1:8,...>

145.

Show

<none>

146.

Add

PREFIX=<NSAP area address - hexString[4:36]>

147.

Remove

PREFIX=<NSAP area address - hexString[4:36]>

148.

Show

[MANAGER=<IP address>]

149.

Add

MANAGER=<IP address> COMMUNITY=<string[1:20]> ACCESS=<readOnly|readWrite|super>TRAPS=<enable|disable>

150.

Edit

MANAGER=<IP address> COMMUNITY=<string[1:20]> [ACCESS=<readOnly|readWrite|super>][TRAPS=<enable|disable>]

151.

Remove

MANAGER=<IP address> COMMUNITY=<string[1:20]>

152.

Command-Line-Interface

[XXXCLI-PASSWORD=<string[6:12]>] [TELNET-PASSWORD=<string[6:12]>] [DISPLAY-LINES=<integer value 0:999>] [ALLOW-MESSAGES=<YES|NO>]

153.

Ethernet-Port-Statistics

ETHERNET-PORT=<integer value 1:8>

154.

Show

<none>

155.

Add

ETHERNET-PORT=<integer value 1:8>

156.

Remove

ETHERNET-PORT=<integer value 1:8>

157.

VC12-Statistics

KLM=<K.L.M - integer value 1:3.integer value 1:7.integer value 1:3>

158.

VC4-Statistics

<none>

159.

MS-Statistics

AGGREGATE-PORT=<integer value 1:2>

160.

RS-Statistics

AGGREGATE-PORT=<integer value 1:2>

161.

General

[BRIDGE-FORWARDNG-TABLE-AFTER-RESET=<integer value>] [RMON-LOG-TABLE-AFTER-RESET=<integer value>] [GVRP-VLAN-ENTRIES-AFTER-RESET=<integer value>][RULES-POLICY-MIB-AFTER-RESET=<integer value>] [PROFILES-POLICY-MIB-AFTER-RESET=<integer value>] [VLAN-ENTRIES-AFTER-RESET=<integer value>][ERROR-REPORT-LEVEL=<integer value>]

162.

IP-Tuning

[IP-RIP-MAX-ENTRIES-AFTER-RESET=<integer value>] [ARP-FORWARDING-MAX-ENTRIES-AFTER-RESET=<integer value>] [IP-FFT-MAX-ENTRIES-AFTER-RESET=<integer value>] [DHCP-MAX-CONNECTION-AFTER-RESET=<integer value>] [IP-FFT-UPPER-LIMIT=<integer value 0:100>][IP-FFT-LOWER-LIMIT=<integer value 0:100>]

163.

IPX-Tuning

[IPX-RIP-MAX-ENTRIES-AFTER-RESET=<integer value>] [IPX-SAP-MAX-ENTRIES-AFTER-RESET=<integer value>] [IPX-FFT-MAX-ENTRIES-AFTER-RESET=<integer value>][IPX-FFT-UPPER-LIMIT=<integer value 1:100>][IPX-FFT-LOWER-LIMIT=<integer value 0:100>]

164.

Event-Log

<none>

165.

Connect-Remote

<none>

166.

Show

[IP-ADDRESS=<IP address>]

167.

Add

IP-ADDRESS=<IP address> [COUNT=<integer value 1:2147483647>] [SIZE=<integer value>] [TIMEOUT=<integer value 0:3600000>] [DELAY=<integer value 0:3600000>]

168.

Remove

IP-ADDRESS=<IP address>

169.

Current-Alarms

<none>

170.

Alarm-History

<none>

171.

Alarm-Reporting

[ALARM-REPORTING=<enabled|disabled>]

172.

Show

[OBJECT-TYPE=<DEVICE|GFP|VCATLC|ALARM|TRIB|SPI|RST|MST|MSP|VC-4|AU-4|TU-12| VC-12|TU-3|VC-3>]

173.

Edit

OBJECT-TYPE=<DEVICE|GFP|VCATLC|ALARM|TRIB|SPI|RST|MST|MSP|VC-4|AU-4|TU-12| VC-12|TU-3|VC-3>[ALARM-REPORTING=<enabled|disabled>][PORT=<integer value 1:12>][PERSISTENCY-ON=<integer value 0:255>][PERSISTENCY-OFF=<integer value 0:255>][SD-THRESHOLD=<integer value 6:9>][AIS=<enabled|disabled>][RDI=<enabled|disabled>]

174.

Show

[ALARM-ID=<unknownAlarmId|hwFail|losSy|aux|losTx|aisRx|lfaRx|lfaTx|los|lof| td|tf|exc|deg|csf|tim|ais|rdi|msp|lom|lop|uneq|plm|fan|temp|unass| wanDelay|syncHoldOver|seqFail|plc|tlc|degFcs|degtHec|upm|clos|lfd| exm|pfm|sqnc|sqm|loa|loaNoTraf|acMstTimeout|rsAckTimeout| eosMultiple|eosMissing|sqNonCont|sqMultiple|sqOor|gidErr|ctrlOor| lcasCrc|nonLcas|mnd|fopr|plcr|tlcr|plct|tlct|info|lanOn|lanOff| rxOverflowHWFault|txOverflowHWFault|routeTableOverflow| resetRequired|endTftp|abortTftp|startTftp|faultBackUp|mainLinkUp| ipxRipTblOverflow|ipxSapTblOverflow|facsAccessVoilation| autoConfigurationCompleted|forwardingTabOverflow| framRelaySwitchConnectionUp|framRelaySwitchConnectionDown| errorsDuringInit|vlanDynPortAdded|vlanDynPortRemoved| rsSDclientsTableOverflow|rsSDinactiveServer| rsIpZhrConnectionsTableOverflow|rsIpZhrReqStaticConnNotAccepted| rsIpZhrVirtualIpAsSource|rsIpZhrNotAllocVirtualIp| rsSnmpSetRequestInSpecialCfgState|rsPingCompletion| pppSecurityViolation|frDLCIStatudChange|papFailedCommunication| chapFailedCommunication|rsWSDRedundancySwitch| rsDhcpAllocationFailure|rlIgmpTableOverflow|rlPimTableOverflow| rlIpFftStnOverflow|rlIpFftSubOverflow|rlIpxFftStnOverflow| rlIpxFftSubOverflow|rlIpmFftOverflow|rlPhysicalDescriptionChanged| rldot1dStpPortStateForwarding|rldot1dStpPortStateNotForwarding| rlPolicyDropPacketTrap|rlPolicyForwardPacketTrap>]

175.

Edit

ALARM-ID=<unknownAlarmId|hwFail|losSy|aux|losTx|aisRx|lfaRx|lfaTx|los|lof|td tf|exc|deg|csf|tim|ais|rdi|msp|lom|lop|uneq|plm|fan|temp|unass| wanDelay|syncHoldOver|seqFail|plc|tlc|degFcs|degtHec|upm|clos|lfd| exm|pfm|sqnc|sqm|loa|loaNoTraf|acMstTimeout|rsAckTimeout| eosMultiple|eosMissing|sqNonCont|sqMultiple|sqOor|gidErr|ctrlOor| lcasCrc|nonLcas|mnd|fopr|plcr|tlcr|plct|tlct|info|lanOn|lanOff| rxOverflowHWFault|txOverflowHWFault|routeTableOverflow| resetRequired|endTftp|abortTftp|startTftp|faultBackUp|mainLinkUp| ipxRipTblOverflow|ipxSapTblOverflow|facsAccessVoilation| autoConfigurationCompleted|forwardingTabOverflow| framRelaySwitchConnectionUp|framRelaySwitchConnectionDown| errorsDuringInit|vlanDynPortAdded|vlanDynPortRemoved| rsSDclientsTableOverflow|rsSDinactiveServer| rsIpZhrConnectionsTableOverflow|rsIpZhrReqStaticConnNotAccepted| rsIpZhrVirtualIpAsSource|rsIpZhrNotAllocVirtualIp| rsSnmpSetRequestInSpecialCfgState|rsPingCompletion| pppSecurityViolation|frDLCIStatudChange|papFailedCommunication| chapFailedCommunication|rsWSDRedundancySwitch| rsDhcpAllocationFailure|rlIgmpTableOverflow|rlPimTableOverflow| rlIpFftStnOverflow|rlIpFftSubOverflow|rlIpxFftStnOverflow| rlIpxFftSubOverflow|rlIpmFftOverflow|rlPhysicalDescriptionChanged| rldot1dStpPortStateForwarding|rldot1dStpPortStateNotForwarding| rlPolicyDropPacketTrap|rlPolicyForwardPacketTrap>ALARM-POINT=<unknownAlarmPoint|device|sdhPhysical|rst|mst|msp|au4|vc4|tu12| vc12|trib|aux|ethernet|wan|tu3|vc3|wanx|gfp|lcas|vcat>[SEVERITY=<critical|major|minor|warning>][DESCRIPTION=<string[0:160]>]

176.

LED-Severity

[CUSTOMER-LED-MIN-SEVERITY=<critical|major|minor|warning>][OPERATOR-LED-MIN-SEVERITY=<critical|major|minor|warning>]

177.

Operating- Parameters

[IP-REDUNDANCY-ADMIN-STATUS=<enable|disable>] [ARP-INACTIVE-TIMEOUT=<integer value>][ARP-PROXY=<enable|disable>] [ICMP-ERROR-MSG=<enable|disable>]

178.

Show

[IP-ADDRESS=<IP address>]

179.

Add

IP-ADDRESS=<IP address> SUBNET-MASK=<IP address> IF-NUMBER=<integer value> [FWD-BROADCAST=<enable|disable>] [BROADCAST-TYPE=<ZERO-FILL|ONE-FILL>] [ARP-SERVER=<enable|disable>]

180.

Edit

IP-ADDRESS=<IP address> [SUBNET-MASK=<IP address>] [IF-NUMBER=<integer value>][FWD-BROADCAST=<enable|disable>] [BROADCAST-TYPE=<ZERO-FILL|ONE-FILL>][ARP-SERVER=<enable|disable>]

181.

Remove

IP-ADDRESS=<IP address>

182.

Show

[IP-ADDRESS=<IP address>]

183.

Edit

IP-ADDRESS=<IP address> [DESTINATION=<ALL-SYSTEMS-MULTICAST|LIMITED-BROADCAST>][MAX-INTERVAL=<integer value 4:1800>] [MIN-INTERVAL=<integer value 3:1800>] [LIFETIME=<integer value 4:9000>] [ADVERTISE=<enable|disable>] [PREFERENCE-LEVEL=<integer value>][DEFAULT-VALUES=<TRUE|FALSE>]

184.

Parameters

[ADMINISTRATIVE-STATUS=<enable|disable>] [LEAK-OSPF=<enable|disable>] [LEAK-STATIC=<enable|disable>]

185.

Show

[IP-ADDRESS=<IP address>]

186.

Edit

IP-ADDRESS=<IP address>[OUTGOING-RIP=<doNotSend|ripVersion1|rip1Compatible|ripVersion2|ripV1Dem ripV2Demand>][INCOMING-RIP=<rip1|rip2|rip1OrRip2|doNotRecieve>] [DEFAULT-METRIC=<integer value 0:15>][AUTO-SEND=<enable|disable>] [VIRTUAL-DISTANCE=<integer value>] [STATUS=<valid|invalid>]

187.

Add

TYPE=<input|output> NETWORK-ADDRESS=<IP address> NUM-MATCH-BITS=<integer value 1:32>ACTION=<deny|permit>

188.

Edit

TYPE=<input|output> NUMBER=<integer value> [NETWORK-ADDRESS=<IP address>] [NUM-MATCH-BITS=<integer value 1:32>] [ACTION=<deny|permit>]

189.

Remove

TYPE=<input|output> NUMBER=<integer value>

190.

Show

[IP-ADDRESS=<IP address>]

191.

Add

IP-ADDRESS=<IP address> TYPE=<input|output> NETWORK-ADDRESS=<IP address> NUM-MATCH-BITS=<integer value 1:32> ACTION=<deny|permit>

192.

Edit

IP-ADDRESS=<IP address> TYPE=<input|output> NUMBER=<integer value> [NETWORK-ADDRESS=<IP address>] [NUM-MATCH-BITS=<integer value 1:32>] [ACTION=<deny|permit>]

193.

Remove

IP-ADDRESS=<IP address> TYPE=<input|output> NUMBER=<integer value>

194.

Show

[IP-ADDRESS=<IP address>]

195.

Edit

IP-ADDRESS=<IP address> [AREA-ID=<IP address>] [IF-TYPE=<broadcast|nbma|pointToPoint|pointToMultipoint>][ADMINISTRATIVE-STATUS=<enabled|disabled>] [PRIORITY=<integer value 0:255>] [HELLO-INTERVAL=<integer value 1:65535>] [ROUTER-DEAD-INTERVAL=<integer value 0:2147483647>][IF-AUTHENTICATION-KEY=<string[0:8]>] [AUTHENTICATION-TYPE=<none|password>][METRIC-VALUE=<integer value 0:65535>]

196.

Parameters

[ADMINISTRATIVE-STATUS=<enabled|disabled>] [ROUTER-ID=<IP address>] [LEAK-RIP=<enable|disable>][LEAK-STATIC=<enable|disable>] [LEAK-EXTERNAL=<enable|disable>]

197.

Show

[AREA-ID=<IP address>]

198.

Add

AREA-ID=<IP address> IMPORT-AS-EXTERN=<importExternal|importNoExternal|importNssa> [METRIC=<integer value 0:16777215>]

199.

Edit

AREA-ID=<IP address> [IMPORT-AS-EXTERN=<importExternal|importNoExternal|importNssa>][METRIC=<integer value 0:16777215>]

200.

Remove

AREA-ID=<IP address>

201.

Add

DEST-IP-ADDRESS=<IP address> DEST-SUBNET-MASK=<IP address> NEXT-HOP=<IP address>IF-NUMBER=<integer value> ROUTE-TYPE=<remote|reject> METRIC=<integer value>

202.

Edit

DEST-IP-ADDRESS=<IP address> DEST-SUBNET-MASK=<IP address> NEXT-HOP=<IP address>METRIC=<integer value>

203.

Remove

DEST-IP-ADDRESS=<IP address> DEST-SUBNET-MASK=<IP address> NEXT-HOP=<IP address>

204.

Add

IF-NUMBER=<integer value> IP-ADDRESS=<IP address> MAC-ADDRESS=<MAC address - hexString[0:320]>

205.

Edit

IF-NUMBER=<integer value> IP-ADDRESS=<IP address> MAC-ADDRESS=<MAC address - hexString[0:320]>

206.

Remove

IF-NUMBER=<integer value> IP-ADDRESS=<IP address>

207.

Add

IF-IP-ADDRESS=<IP address> MAIN-ROUTER-IP-ADDRESS=<IP address> [POLL-INTERVAL=<integer value>][TIMEOUT=<integer value>]

208.

Edit

IF-IP-ADDRESS=<IP address> MAIN-ROUTER-IP-ADDRESS=<IP address> [OPERATIONAL-STATUS=<active|inactive>] [POLL-INTERVAL=<integer value>] [TIMEOUT=<integer value>]

209.

Remove

IF-IP-ADDRESS=<IP address> MAIN-ROUTER-IP-ADDRESS=<IP address>

210.

Parameters

[SERVER-ENABLE=<enable|disable>] [NEXT-SERVER-ADDRESS=<IP address>] [SECURITY-THRESHOLD=<integer value>] [DNS-IP-ADDRESS=<IP address>] [PROBE-ENABLE=<enable|disable>] [PROBE-RETRIES=<integer value>] [PROBE-TIMEOUT=<integer value>][PRIMARY-WINS-SERVER=<IP address>] [SECONDARY-WINS-SERVER=<IP address>] [NODE-TYPE=<BROADCAST|POINT-TO-POINT|HYBRID|MIXED>]

211.

Add

IF-IP-ADDRESS=<IP address> IP-ADDRESS-FROM=<IP address> IP-ADDRESS-TO=<IP address>DEFAULT-ROUTER=<IP address> LEASE-TIME=<integer value> PROBE-ENABLE=<enable|disable>

212.

Edit

IF-IP-ADDRESS=<IP address> IP-ADDRESS-FROM=<IP address> IP-ADDRESS-TO=<IP address>[DEFAULT-ROUTER=<IP address>] [LEASE-TIME=<integer value>] [PROBE-ENABLE=<enable|disable>]

213.

Remove

IF-IP-ADDRESS=<IP address> IP-ADDRESS-FROM=<IP address> IP-ADDRESS-TO=<IP address>

214.

Add

IP-ADDRESS=<IP address> MAC-ADDRESS=<MAC address - hexString[0:320]> HOST-NAME=<string[0:20]>DEFAULT-ROUTER=<IP address> CONFIG-SERVER-IP=<IP address> CONFIG-FILE-NAME=<string[0:128]>

215.

Edit

IP-ADDRESS=<IP address> [MAC-ADDRESS=<MAC address - hexString[0:320]>] [HOST-NAME=<string[0:20]>][DEFAULT-ROUTER=<IP address>] [CONFIG-SERVER-IP=<IP address>] [CONFIG-FILE-NAME=<string[0:128]>]

216.

Remove

IP-ADDRESS=<IP address>

217.

Add

IF-NUMBER=<integer value> NETWORK-ADDRESS=<IPX network number - hexString[8:8]> TIME-TO-NETWORK=<integer value 1:65535> LAYER2-ENCAP=<novell|ethernet|llc|snap|none> NETBIOS=<enabled|disabled> ADMINISTRATIVE-STATUS=<off|on|sleeping>

218.

Edit

CIRCUIT-NUMBER=<integer value> [TIME-TO-NETWORK=<integer value 1:65535>][LAYER2-ENCAP=<novell|ethernet|llc|snap|none>] [NETBIOS=<enabled|disabled>] [ADMINISTRATIVE-STATUS=<off|on|sleeping>]

219.

Remove

CIRCUIT-NUMBER=<integer value>

220.

RIP-Parameters

CIRCUIT-NUMBER=<integer value> [UPDATE-INTERVAL=<integer value>] [AGE-MULTIPLIER=<integer value>][STATUS=<off|on>]

221.

SAP-Parameters

CIRCUIT-NUMBER=<integer value> [UPDATE-INTERVAL=<integer value>] [AGE-MULTIPLIER=<integer value>][RESPOND-TO-GET-SERVER=<no|yes>] [STATUS=<off|on>]

222.

Add

TYPE=<input|output> NETWORK-ADDRESS=<IPX network number - hexString[8:8]>NETWORK-MASK=<IPX network number - hexString[8:8]> ACTION=<deny|permit>

223.

Edit

TYPE=<input|output> NUMBER=<integer value> [NETWORK-ADDRESS=<IPX network number - hexString[8:8]>][NETWORK-MASK=<IPX network number - hexString[8:8]>] [ACTION=<deny|permit>]

224.

Remove

TYPE=<input|output> NUMBER=<integer value>

225.

Show

[CIRCUIT-NUMBER=<integer value>]

226.

Add

CIRCUIT-NUMBER=<integer value> TYPE=<input|output> NETWORK-ADDRESS=<IPX network number - hexString[8:8]> NETWORK-MASK=<IPX network number - hexString[8:8]> ACTION=<deny|permit>

227.

Edit

CIRCUIT-NUMBER=<integer value> TYPE=<input|output> NUMBER=<integer value>[NETWORK-ADDRESS=<IPX network number - hexString[8:8]>] [NETWORK-MASK=<IPX network number - hexString[8:8]>] [ACTION=<deny|permit>]

228.

Remove

CIRCUIT-NUMBER=<integer value> TYPE=<input|output> NUMBER=<integer value>

229.

Add

TYPE=<input|output> NETWORK-ADDRESS=<IPX network number - hexString[8:8]> NETWORK-MASK=<IPX network number - hexString[8:8]> SERVICE-TYPE=<IPX server type - hexString[4:4]>SERVICE-NAME=<string[1:48]> ACTION=<deny|permit>

230.

Edit

TYPE=<input|output> NUMBER=<integer value> [NETWORK-ADDRESS=<IPX network number - hexString[8:8]>][NETWORK-MASK=<IPX network number - hexString[8:8]>] [SERVICE-TYPE=<IPX server type - hexString[4:4]>][SERVICE-NAME=<string[1:48]>] [ACTION=<deny|permit>]

231.

Remove

TYPE=<input|output> NUMBER=<integer value>

232.

Show

[CIRCUIT-NUMBER=<integer value>]

233.

Add

CIRCUIT-NUMBER=<integer value> TYPE=<input|output> NETWORK-ADDRESS=<IPX network number - hexString[8:8]> NETWORK-MASK=<IPX network number - hexString[8:8]> SERVICE-TYPE=<IPX server type - hexString[4:4]>SERVICE-NAME=<string[1:48]> ACTION=<deny|permit>

234.

Edit

CIRCUIT-NUMBER=<integer value> TYPE=<input|output> NUMBER=<integer value> [NETWORK-ADDRESS=<IPX network number - hexString[8:8]>] [NETWORK-MASK=<IPX network number - hexString[8:8]>] [SERVICE-TYPE=<IPX server type - hexString[4:4]>][SERVICE-NAME=<string[1:48]>] [ACTION=<deny|permit>]

235.

Remove

CIRCUIT-NUMBER=<integer value> TYPE=<input|output> NUMBER=<integer value>

236.

Add

DEST-NETWORK=<IPX network number - hexString[8:8]> CIRCUIT-NUMBER=<integer value> NEXT-HOP=<IPX network number - hexString[8:8]> [TICKS-TO-NET=<integer value>] [HOPS-TO-NET=<integer value>] [FORWARDING-ROUTER=<MAC address - hexString[12:12]>]

237.

Edit

DEST-NETWORK=<IPX network number - hexString[8:8]> CIRCUIT-NUMBER=<integer value>[TICKS-TO-NET=<integer value>] [HOPS-TO-NET=<integer value>][FORWARDING-ROUTER=<IPX node address - hexString[12:12]>] [NEXT-HOP=<IPX network number - hexString[8:8]>]

238.

Remove

DEST-NETWORK=<IPX network number - hexString[8:8]>CIRCUIT-NUMBER=<integer value>

239.

Add

SERVER-NAME=<string[1:48]> SERVER-TYPE=<IPX server type - hexString[4:4]> NETWORK=<IPX network number - hexString[8:8]> SERVER-ADDRESS=<IPX node address - hexString[12:12]>SOCKET=<IPX socket type - hexString[4:4]> HOPS-TO-SERVER=<integer value>

240.

Edit

SERVER-NAME=<string[1:48]> SERVER-TYPE=<IPX server type - hexString[4:4]> [NETWORK=<IPX network number - hexString[8:8]>] [SERVER-ADDRESS=<IPX node address - hexString[12:12]>][SOCKET=<IPX socket type - hexString[4:4]>] [HOPS-TO-SERVER=<integer value>]

241.

Remove

SERVER-NAME=<string[1:48]> SERVER-TYPE=<IPX server type - hexString[4:4]>

242.

Operating-Parameters

[IPM-ENABLE=<enabled|disabled>]

243.

Show

[IF-INDEX=<integer value>]

244.

Add

IF-INDEX=<integer value> [QUERY-INTERVAL=<integer value>] [VERSION=<integer value>] [MAX-RESPONSE-TIME=<integer value 0:255>] [ROBUSTNESS=<integer value 1:255>] [LAST-MEMBER-QUERY-INTVL=<integer value 0:255>]

245.

Edit

IF-INDEX=<integer value> [QUERY-INTERVAL=<integer value>] [VERSION=<integer value>] [MAX-RESPONSE-TIME=<integer value 0:255>] [ROBUSTNESS=<integer value 1:255>][LAST-MEMBER-QUERY-INTVL=<integer value 0:255>

246.

Remove

[IF-INDEX=<integer value>]

247.

Cache-Table

[CACHE-ADDRESS=<IP address>] [IF-INDEX=<integer value>]

248.

Routing-Table

[GROUP=<IP address>] [SOURCE=<IP address>] [MASK=<IP address>]

249.

Next-Hop

[GROUP=<IP address>] [SOURCE=<IP address>] [MASK=<IP address>] [IF-INDEX=<integer value>] [ADDRESS=<IP address>]

250.

Device-Parameters

[GVRP-STATUS=<enabled|disabled>]

251.

Port-Parameters

[PORT-NUMBER=<integer value 1:8>] [GVRP-STATUS=<enabled|disabled>]

252.

Timing-Parameters

[PORT-NUMBER=<integer value 1:8>] [JOIN-TIME=<integer value>] [LEAVE-TIME=<integer value>] [ALL-LEAVE-TIME=<integer value>]

253.

Display-Statistics

[PORT-NUMBER=<integer value 1:8>]

254.

PORT-MIRRORING

[MIRRORED-PORT=<disabled|1|2|3|4|5|6|7|8>] [COPY-PORT=<disabled|1|2|3|4|5|6|7|8>]

255.

Running-Config

[SECTION-LIST=<integer value 1:9,...>] No input parameter starts all sections. 1 - Section 1 General information. 2 - Section 2 Alarms. 3 - Section 3 Routing(IP) information. 4 - Section 4 Management configuration. 5 - Section 5 Bridge configuration. 6 - Section 6 Ports configuration. 7 - Section 7 VLAN configuration. 8 - Section 8 Statistics. 9 - Section 9 Compressed status report.

256.

Used

[SORT-MODE=<LEX|G707>]

257.

Show

[IF-INDEX=<integer value>]

258.

Add

IF-INDEX=<integer value> [JOIN-PRUNE-INTV=<integer value>] [MODE=<dense|sparse|sparseDense>] [HELLO-INTV=<integer value>]

259.

Edit

IF-INDEX=<integer value> [JOIN-PRUNE-INTV=<integer value>] [MODE=<dense|sparse|sparseDense>][HELLO-INTV=<integer value>]

260.

Remove

[IF-INDEX=<integer value>]

261.

Nighbor-Table

[ADDRESS=<IP address>]

262.

Route-Table

[GROUP=<IP address>] [SOURCE=<IP address>] [MASK=<IP address>]

263.

Next-Hop-Table

[GROUP=<IP address>] [SOURCE=<IP address>] [MASK=<IP address>] [IF-INDEX=<integer value>] [ADDRESS=<IP address>]

264.

Clear-SDH-Counters

<none>

265.

System-Mode

[SYSTEM-MODE=<ip|ip-unnumbered>]

266.

Add (Ipun-Route-Table)

DEST-IP-ADDR=<IP address>SUBNET-MASK=<IP address>NEXT-HOP=<IP address>[METRIC=<integer value>]

267.

Remove (Ipun-Route-Table)

DEST-IP-ADDR=<IP address>SUBNET-MASK=<IP address>NEXT-HOP=<IP address>

268.

Global-parameter

[OSPF-IPUN-ADMINISTRATIVE-STATUS=<enabled|disabled>][LEAK-STATIC-ROUTES-TO-OSPF=<enable|disable>][LEAK-EXTERNAL-ROUTES-TO-OSPF=<enable|disable>]

269.

Add

AREA-ID=<IP address>

270.

Show

[IP-ADDRESS=<IP address>][IF-INDEX=<integer value>]

271.

Edit

IP-ADDRESS=<IP address>IF-INDEX=<integer value>[AREA-ID=<IP address>][ADMIN-STATUS=<enabled|disabled>][ROUTER-PRIORITY=<integer value 0:255>][RETRANSMISSION-INTERVAL=<integer value 0:3600>][HELLO-INTERVAL=<integer value 1:65535>][TRANSMISSION-DELAY=<integer value 0:3600>][ROUTER-DEAD-INTERVAL=<integer value 0:2147483647>]

272.

ES-IS-Configuration

[STATUS=<enabled|disabled>][ES-HOLD-TIMER=<integer value 0:65535>][ES-REPORT-TIMER=<integer value 0:65535>][IS-HOLD-TIMER=<integer value 0:65535>][IS-REPORT-TIMER=<integer value 0:65535>][SUGGESTED-TIMER=<integer value 0:65535>]

273.

IS-IS-Configuration

[STATUS=<enabled|disabled>][L1-METRIC=<integer value 1:63>][L2-METRIC=<integer value 1:63>][CIRCUIT-OUTSIDE-DOMAIN=<enabled|disabled>][IS-IS-HELLO-TIMER=<integer value 0:65535>][L1-DIS-PRIORITY=<integer value 1:127>][L2-DIS-PRIORITY=<integer value 1:127>][DIS-IIH-TIMER=<integer value 0:65535>]

274.

CLNP-Configuration

[MAXIMUM-CLNP-PDU-LIFETIME=<integer value 0:65535>][MAXIMUM-CLNP-REASSEMBLY-TIME=<integer value 0:65535>]

275.

Show

<none>

276.

Add

NSAP=<NSAP address - hexString[6:40]>

277.

Remove

NSAP=<NSAP address - hexString[6:40]>

278.

Gateway-settings

[GATEWAY-ENABLED=<true|false>]

279.

show

WANX-PORT=<integer value 6:8>

280.

General

WANX-PORT=<integer value 6:8>[CONCATENATION=<vcatvc12|vcatvc3|axxessit>][CHANNEL-TI/SIGNAL-LABEL=<integer value 0:50>][PATH-TRACE=<enabled|disabled>][EXPECTED-TI=<string[1:15]>][HEX-EXPECTED-TI=<string[2:44]>][TRANSMIT-TI=<string[1:15]>][HEX-TRANSMIT-TI=<string[2:44]>][LCAS-OPERATIONAL-MODE=<lcas|nolcas|nolcasbidirectional>][ADMIN-UPSTREAM-CAPASITY=<integer value>][ADMIN-DOWNSTREAM-CAPASITY=<integer value>][PAYLOAD-FCS-INDICATOR=<FCS-ENABLED|FCS-DISABLED>][QTAG-STATUS=<transparentPriority|extractPriority|disabled>][FLOW-CONTROL=<enabled|disabled>][PROTOCOL-TUNNELING=<enabled|disabled>][STP-TUNNELING=<enabled|disabled>][VTP-TUNNELING=<enabled|disabled>][CDP-TUNNELING=<enabled|disabled>]

281.

Add-VC3-VC12-channel

WAN-PORT=<integer value 6:8>[KLM=<K.L.M - integer value 1:3.integer value 1:7.integer value 1:3>][ADMIN-STATUS=<enabled|disabled>][NUMBER-TO-ADD=<integer value 1:50>][SORT-MODE=<LEX|G707>]

282.

Remove-VC3-VC12-channel

WAN-PORT=<integer value 6:8>[NUMBER-TO-REMOVE=<integer value 1:50>]

283.

Free-VC12VC3-List

<none>

284.

Used-VC12VC3-List

<none>

285.

General

AGGREGATE-PORT=<integer value 1:2>[ADMINISTRATIVE-STATUS=<enable|disable>][DESCRIPTION=<string[0:64]>][CONNECTED-TO=<string[0:64]>]

286.

TUG3-mapping

[K=<integer value 1:3>][STRUCTURE=<tu3|tu12x21>]

287.

Show-VC3-VC12-Mapping

<none>

288.

List-VC3-VC12-Usage

[SORT-MODE=<LEX|G707>]

289.

Protection

[MSP-STATUS=<enabled|disabled>][PROTECTION-TYPE=<unidirectional|bidirectional>][REVERTING-STATUS=<enabled|disabled>][WAIT-TO-RESTORE-TIME=<integer value 0:2147483647>][SWITCHING-COMMAND=<clear|exercise|manualSwitchToProtection| manualSwitchToWorking|forcedSwitchToProtection| forcedSwitchToWorking|lockoutProtection>]

290.

VC4-Path-Trace

[PATH-TRACE=<enabled|disabled>][EXPECTED-TI=<string[1:15]>][HEX-EXPECTED-TI=<string[2:44]>][TRANSMIT-TI=<string[1:15]>][HEX-TRANSMIT-TI=<string[2:44]>]

291.

RS-Path-Trace

AGGREGATE-PORT=<integer value 1:2>[PATH-TRACE=<enabled|disabled>][EXPECTED-TI=<string[1:15]>][HEX-EXPECTED-TI=<string[2:44]>][TRANSMIT-TI=<string[1:15]>][HEX-TRANSMIT-TI=<string[2:44]>]

292.

General

[SPANNING-TREE-ENABLED=<true|false>][FORCED-PROTOCOL=<stpCompatible|rstp>][BELONG-TO-VLAN=<true|false>][PRIORITY=<integer value 0:65535>][MAX-AGE=<integer value>][HELLO-TIME=<integer value>][FORWARD-DELAY=<integer value>]

293.

Port-Table

[ETHERNET-PORT=<integer value 1:8>][PRIORITY=<integer value 0:255>][ENABLE=<enabled|disabled>][PATH-COST=<integer value 0:200000000>][EDGE-PORT=<true|false>][POINT-POINT=<forceTrue|forceFalse|auto>][PROTOCOL-MIGRATION=<true|false>]

294.

Tuning

<none>

295.

show

<none>

296.

edit

PRIORITY=<integer value 0:7>TRAFFIC-CLASS=<integer value 0:3>

297.

GFP-Bad-Frames-Statistics

[WANX-PORT=<integer value 6:8>]

298.

Enable-GFP-Counters

WANX-PORT=<integer value 6:8>

299.

Disable-GFP-Counters

WANX-PORT=<integer value 6:8>

300.

Show-GFP-Counters

[WANX-PORT=<integer value 6:8>]

301.

Clear-GFP-Counters

<none>

302.

Parameters

<none>

303.

Clear-Event-Log

<none>

304.

VC3-Statistics

K=<integer value 1:3>[SHOW-ALL-INTERVALS=<FALSE|TRUE>]

305.

MSP-Statistics

<none>

306.

Trib-Port-Statistics

TRIB-PORT=<integer value 1:12>[SHOW-ALL-INTERVALS=<FALSE|TRUE>]



hometocprevnextglossaryfeedbacksearchhelp

Posted: Tue Jan 8 08:07:12 PST 2008
All contents are Copyright © 1992--2008 Cisco Systems, Inc. All rights reserved.
Important Notices and Privacy Statement.