Table Of Contents

TL1 Commands

9.1 Introduction

9.2 Connection to the ONS 15216 EDFA2

9.3 Explanation of Command Parameters

9.3.1 Source Identifier (sid) and Target Identifier (tid)

9.3.2 Command Code Modifier (ccm)

9.3.3 Access Identifier (aid)

9.3.4 Correlation Tag (ctag)

9.4 Notation

9.5 Summary of Autonomous Alarms and Messages

9.6 Summary of Security Permissions for TL1 Commands

9.7 TL1 Commands and Autonomous Messages

9.7.1 ACT-USER

9.7.2 ALW-MSG-ALL

9.7.3 APPLY

9.7.4 CANC-USER

9.7.5 COPY-RFILE

9.7.6 CPY-MEM

9.7.7 DLT-RFILE

9.7.8 DLT-USER-SECU

9.7.9 ED-DAT

9.7.10 ED-DWDM

9.7.11 ED-ENV

9.7.12 ED-NE-GEN

9.7.13 ED-PID

9.7.14 ED-USER-SECU

9.7.15 ENT-USER-SECU

9.7.16 INH-MSG-ALL

9.7.17 INIT-SYS

9.7.18 REPT ALM DWDM

9.7.19 REPT ALM ENV

9.7.20 REPT ALM EQPT

9.7.21 REPT EVT DWDM / REPT EVT ENV / REPT EVT EQPT

9.7.22 REPT EVT FXFR

9.7.23 RTRV-ALM-ALL

9.7.24 RTRV-ALM-DWDM

9.7.25 RTRV-ALM-ENV

9.7.26 RTRV-ALM-EQPT

9.7.27 RTRV-AO

9.7.28 RTRV-COND-ALL

9.7.29 RTRV-COND-DWDM

9.7.30 RTRV-COND-ENV

9.7.31 RTRV-COND-EQPT

9.7.32 RTRV-DFLT-SECU

9.7.33 RTRV-DWDM

9.7.34 RTRV-ENV

9.7.35 RTRV-HDR

9.7.36 RTRV-INV

9.7.37 RTRV-NE-GEN

9.7.38 RTRV-RFILE

9.7.39 RTRV-TH-DWDM

9.7.40 RTRV-TH-ENV

9.7.41 RTRV-TH-EQPT

9.7.42 RTRV-TOD

9.7.43 RTRV-USER-SECU

9.7.44 SET-ATTR-SECUDFLT

9.7.45 SET-TH-DWDM

9.7.46 SET-TH-ENV

9.7.47 SET-TH-EQPT

9.7.48 STA-LOCL-RST

TL1 Commands

---

9.1 Introduction

This chapter provides the details of TL1 commands supported by the Cisco ONS 15216 EDFA2. This chapter also maps various TL1 command parameters to their SNMP counterpart attributes in the ONS 15216 EDFA2 MIB (CERENT-15216-EDFA-MIB.mib).

9.2 Connection to the ONS 15216 EDFA2

The ONS 15216 EDFA2 system supports up to ten simultaneous Telnet connections via the Ethernet LAN port. TL1 sessions are available on TCP/IP port 3082 for raw TL1 and/or port 3083 for TL1 over Telnet. When connected, the ACT-USER command activates a session. (See "Log In via LAN Port Using Telnet (Optional)" section on page 8-3.)

9.3 Explanation of Command Parameters

TL1 messages are grouped into autonomous and non-autonomous types. Autonomous messages are generated as a result of activity on the network elements such as alarms, thresholds, alerts and status information. No request is required in order to receive autonomous messages. Non-autonomous messages consist of a request command and a response from the ONS 15216 EDFA2. Autonomous messages and non-autonomous commands use a common set of parameters. Some of the most common parameters are defined in the following sections.

9.3.1 Source Identifier (sid) and Target Identifier (tid)

The source identifier (sid) or target identifier (tid) parameters uniquely identify an ONS 15216 EDFA2. For the ONS 15216 EDFA2, sid and tid are the same. The sid/tid name is used only by the TL1 shell in the ONS 15216 EDFA2. While the TL1 shell uses the sid/tid name in its command line prompt, the ASH shell uses the host name.

9.3.2 Command Code Modifier (ccm)

The command code modifier (ccm) identifies the object of the action being applied by the verb of the TL1 command. Some command code modifiers for the ONS 15216 EDFA2 are described in Table 9-1.

Table 9-1 Command Code Modifiers

ccm	Description
DWDM	Optical parameters.
ENV	Environmental (power bus) parameters.
EQPT	General parameters of the ONS 15216 EDFA2.
INV	Inventory parameters.
NE-GEN	IP communications parameters.

9.3.3 Access Identifier (aid)

The access identifier (aid) parameter uniquely identifies an object within the ONS 15216 EDFA2. For the ONS 15216 EDFA2, there are four specific aids (1, PWR-A, PWR-B, EQPT) and the ALL aid, as described in Table 9-2. All autonomous messages identify their specific aid in the message. For all command inputs that require an aid as a mandatory parameter, the ALL aid is accepted as well as any relevant specific aids. If the ALL aid is used in a command, the response contains the appropriate specific aid. For the commands RTRV-ALM-ENV and RTRV-COND-ENV, inputting a specific aid filters the response to information relevant to that aid.

Table 9-2 Access Identifiers

aid	Description
1	Directly affecting the optical signal.
PWR-A	Affecting Power Bus A (or both A and B).
PWR-B	Affecting Power Bus B.
EQPT	General parameters of the ONS 15216 EDFA2 (not directly affecting optical signal or power bus).
ALL	Any or all of the preceding (command input only).

9.3.4 Correlation Tag (ctag)

The correlation tag (ctag) is a unique tag associated with a command. If the user specifies a ctag while entering a command, the response of that command from the ONS 15216 EDFA2 TL1 agent carries the same ctag value. The ctag consists of no more than six alphanumeric characters.

9.4 Notation

The commands described in this document use the symbols shown in Table 9-3 to describe the command format. These symbols are derived from the Telcordia Network Maintenance: Network Element and Transport Surveillance Messages Manual (Generic Requirements, GR-833-CORE).

Table 9-3 TL1 Notation Symbols

Symbol	Meaning	Description
[ ]	Optional expression	Square brackets indicate the parameters are optional. An optional parameter means that if a user inputs an empty field for an optional parameter, then a default value (or a default action) will be substituted automatically in the transmitted input field. The default value, or null value, is defined in the parameter descriptions of the messages.
< >	Variable expression	Angle brackets enclose one or more variable items in the command line, e.g., <date>, <time>, <aid>, etc. Italics are used to note variables in paragraph text, e.g., date, time, aid, etc.
+	More than one time	Plus signs indicate that preceding symbol or group of symbols (enclosed in parentheses) may occur one or more times.
text	Indent of three spaces	An indented line indicates an entry of three spaces in the command line.

9.5 Summary of Autonomous Alarms and Messages

Table 9-4 summarizes the ONS 15216 EDFA2 autonomous alarms. Table 9-5 summarizes the ONS 15216 EDFA2 autonomous events. Table 9-6 summarizes the ONS 15216 EDFA2 file transfer events. Table 9-7 summarizes the ONS 15216 EDFA2 clear alarms.

Table 9-4 TL1 Autonomous Alarms 

TL1 Autonomous Message	Condition Type (condtype)	Condition Descriptor (conddescr)	Access Identifier (aid)	Notification Code (ntfcncde)	Service Effect (srveff)
REPT ALM DWDM	LOS	Loss Of Signal (input power)	1	MJ	SA
REPT ALM DWDM	GAIN	Gain Out Of Range	1	MJ	SA
REPT ALM DWDM	LPOUT	Loss Of Output Power	1	MJ	SA
REPT ALM ENV	PWRBUSA	Power Bus A (voltage) Alarm	PWR-A	MJ	-
REPT ALM ENV	PWRBUSB	Power Bus B (voltage) Alarm	PWR-B	MJ	-
REPT ALM EQPT	CTMP	Case Temperature Out Of Range	EQPT	MN	NSA
REPT ALM EQPT	LCRNT1	Excessive Pump1 Current	EQPT	MN	NSA
REPT ALM EQPT	LCRNT2	Excessive Pump2 Current	EQPT	MN	NSA
REPT ALM EQPT	LTMP1	Excessive Pump1 Temperature	EQPT	MN	NSA
REPT ALM EQPT	LTMP2	Excessive Pump2 Temperature	EQPT	MN	NSA

---

Note The messages for Loss of Signal (LOS), Gain Out of Range (GAIN), and Loss of Output Power (LPOUT) are prioritized (in the order just listed) so that only one message can be delivered at one time. For example, if the ONS 15216 EDFA2 detects both a loss of input signal and a loss of output power at the same time, it will deliver only the Loss of Signal (LOS) message to the user. This prioritized filtering of alarms does not occur with the SNMP delivery of alarms of the ONS 15216 EDFA2.

---

Table 9-5 TL1 Autonomous Events 

TL1 Autonomous Message	Condition Type (condtype)	Condition Descriptor (conddescr)	Access Identifier (aid)	Condition Effect (condeff)
REPT EVT DWDM	CTRLMODE1	Pump1 Control Mode Changed	1	TC
REPT EVT DWDM	CTRLMODE2	Pump2 Control Mode Changed	1	TC
REPT EVT DWDM	GAINCHGD	Overall Gain Changed	1	TC
REPT EVT DWDM	LOSHYSTCHGD	LOS (loss of signal) Hysteresis Changed	1	TC
REPT EVT DWDM	LOSTHCHGD	LOS (loss of signal) Threshold Changed	1	TC
REPT EVT DWDM	LPOUTCHGD	Loss Of Output Power Setpoint Changed	1	TC
REPT EVT DWDM	LPOUTDEVCHGD	Lpout (loss of output power) Deviation Changed	1	TC
REPT EVT DWDM	LPOUTHYSTCHGD	Lpout (loss of output power) Hysteresis Changed	1	TC
REPT EVT DWDM	PREATTCHGD	Pre-attenuation Changed	1	TC
REPT EVT ENV	PWRBUSMAXCHGD	Power Bus Max (voltage) Changed	PWR-A	TC
REPT EVT ENV	PWRBUSMINCHGD	Power Bus Min (voltage) Changed	PWR-A	TC
REPT EVT ENV	PWRBUSMODE	Power Bus Mode Changed	PWR-B	TC
REPT EVT EQPT	MAXCTMPCHGD	Max Case Temperature Changed	EQPT	TC
REPT EVT EQPT	MAXCTMPHYSTCHGD	Max Ctmp (case temperature) Hysteresis Changed	EQPT	TC
REPT EVT EQPT	MINCTMPCHGD	Min Case Temperature Changed	EQPT	TC
REPT EVT EQPT	MINCTMPHYSTCHGD	Min Ctmp (case temperature) Hysteresis Changed	EQPT	TC
REPT EVT EQPT	CUTOVERRESET	(Software) Reset After Cutover	EQPT	TC
REPT EVT EQPT	SOFTWARELOAD	(New) Software Load	EQPT	TC
REPT EVT EQPT	SOFTWARERESET	Software Reset	EQPT	TC

Table 9-6 TL1 Autonomous File Transfer Events 

Autonomous TL1 Message	File Transfer Status (fxfr_status)	File Transfer Result (fxfr_rslt)	Access Identifier (aid)
REPT EVT FXFR	START		EQPT
REPT EVT FXFR	COMPLD	SUCCESS	EQPT
		FAILURE	EQPT

Table 9-7 TL1 Autonomous Clear Alarms 

TL1 Autonomous Message	Condition Type (condtype)	Condition Descriptor (conddescr)	Access Identifier (aid)	Notification Code (ntfcncde)	Service Effect (srveff)
REPT ALM DWDM	LOS	Loss Of Signal (input power)	1	CL	SA
REPT ALM DWDM	GAIN	Gain Out Of Range	1	CL	SA
REPT ALM DWDM	LPOUT	Loss Of Output Power	1	CL	SA
REPT ALM ENV	PWRBUSA	Power Bus A (voltage) Alarm	PWR-A	CL	-
REPT ALM ENV	PWRBUSB	Power Bus B (voltage) Alarm	PWR-B	CL	-
REPT ALM EQPT	CTMP	Case Temperature Out Of Range	EQPT	CL	NSA
REPT ALM EQPT	LCRNT1	Excessive Pump1 Current	EQPT	CL	NSA
REPT ALM EQPT	LCRNT2	Excessive Pump2 Current	EQPT	CL	NSA
REPT ALM EQPT	LTMP1	Excessive Pump1 Temperature	EQPT	CL	NSA
REPT ALM EQPT	LTMP2	Excessive Pump2 Temperature	EQPT	CL	NSA

9.6 Summary of Security Permissions for TL1 Commands

Table 9-8 summarizes the security permissions (access levels) for each available TL1 command and autonomous message.

Table 9-8 TL1 Commands and Messages Security Permissions (Access Levels) 

Command or Message	Description	User Access Levels
		R	RW	RWA
ACT-USER	Activates user session (login). See ACT-USER.	Yes	Yes	Yes
ALW-MSG-ALL	Allows automatic (REPT) messages. See ALW-MSG-ALL.	Yes	Yes	Yes
APPLY	Applies software cutover. See APPLY.	No	No	Yes
CANC-USER	Cancels user session (logoff). See CANC-USER.	Yes	Yes	Yes
COPY-RFILE	Copies remote or local file to FFS. See COPY-RFILE.	No	Yes	Yes
CPY-MEM	Copies log file from RAM to FFS. See CPY-MEM.	No	Yes	Yes
DLT-RFILE	Deletes file from FFS. See DLT-RFILE.	No	Yes	Yes
DLT-USER-SECU	Deletes a user. See DLT-USER-SECU.	No	No	Yes
ED-DAT	Edits date and time. See ED-DAT.	No	Yes	Yes
ED-DWDM	Edits optical parameters. See ED-DWDM.	No	Yes	Yes
ED-ENV	Edits power bus mode. See ED-ENV.	No	Yes	Yes
ED-NE-GEN	Edits general IP-related parameters. See ED-NE-GEN.	No	Yes	Yes
ED-PID	Edits user password. See ED-PID.	Yes (own UID)	Yes (own UID)	Yes (all UIDs)
ED-USER-SECU	Edits a user's name and parameters. See ED-USER-SECU.	No	No	Yes
ENT-USER-SECU	Enters new user. See ENT-USER-SECU.	No	No	Yes
INH-MSG-ALL	Inhibits some automatic messages. See INH-MSG-ALL.	Yes	Yes	Yes
INIT-SYS	Initializes (reboots) system. See INIT-SYS.	No	Yes	Yes
REPT ALM DWDM	Message that reports optical alarm activation/clearing. See REPT ALM DWDM.	Yes	Yes	Yes
REPT ALM ENV	Message that reports power-bus alarm activation/clearing. See REPT ALM ENV.	Yes	Yes	Yes
REPT ALM EQPT	Message that reports general alarm activation/clearing. See REPT ALM EQPT.	Yes	Yes	Yes
REPT EVT DWDM REPT EVT ENV REPT EVT EQPT	Message that reports event logging. See REPT EVT DWDM / REPT EVT ENV / REPT EVT EQPT.	Yes	Yes	Yes
REPT EVT FXFR	Message that reports FTP file transfer. See REPT EVT FXFR.	Yes	Yes	Yes
RTRV-ALM-ALL	Retrieves all current alarms. See RTRV-ALM-ALL.	Yes	Yes	Yes
RTRV-ALM-DWDM	Retrieves current optical alarms. See RTRV-ALM-DWDM.	Yes	Yes	Yes
RTRV-ALM-ENV	Retrieves current power-bus alarms. See RTRV-ALM-ENV.	Yes	Yes	Yes
RTRV-ALM-EQPT	Retrieves current general alarms. See RTRV-ALM-EQPT.	Yes	Yes	Yes
RTRV-AO	Retrieves most-recent autonomous output (REPT) messages. See RTRV-AO.	Yes	Yes	Yes
RTRV-COND-ALL	Retrieves condition (state) of all current alarms. See RTRV-COND-ALL.	Yes	Yes	Yes
RTRV-COND-DWDM	Retrieves condition (state) of current optical alarms. See RTRV-COND-DWDM.	Yes	Yes	Yes
RTRV-COND-ENV	Retrieves condition (state) of current power-bus alarms. See RTRV-COND-ENV.	Yes	Yes	Yes
RTRV-COND-EQPT	Retrieves condition (state) of current general alarms. See RTRV-COND-EQPT.	Yes	Yes	Yes
RTRV-DFLT-SECU	Retrieves timeouts for access levels. See RTRV-DFLT-SECU.	No	No	Yes
RTRV-DWDM	Retrieves optical parameters. See RTRV-DWDM.	Yes	Yes	Yes
RTRV-ENV	Retrieves power bus mode. See RTRV-ENV.	Yes	Yes	Yes
RTRV-HDR	Retrieves header (pings NE). See RTRV-HDR.	Yes	Yes	Yes
RTRV-INV	Retrieves inventory parameters. See RTRV-INV.	Yes	Yes	Yes
RTRV-NE-GEN	Retrieves general IP-related parameters. See RTRV-NE-GEN.	Yes	Yes	Yes
RTRV-RFILE	Retrieves files on FFS. See RTRV-RFILE.	Yes	Yes	Yes
RTRV-TH-DWDM	Retrieves optical thresholds. See RTRV-TH-DWDM.	Yes	Yes	Yes
RTRV-TH-ENV	Retrieves power-bus thresholds. See RTRV-TH-ENV.	Yes	Yes	Yes
RTRV-TH-EQPT	Retrieves general thresholds. See RTRV-TH-EQPT.	Yes	Yes	Yes
RTRV-TOD	Retrieves date and time. See RTRV-TOD.	Yes	Yes	Yes
RTRV-USER-SECU	Retrieves access level of user(s). See RTRV-USER-SECU.	Yes (own UID)	Yes (own UID)	Yes (all UIDs)
SET-ATTR-SECUDFLT	Sets timeout values for access levels. See SET-ATTR-SECUDFLT.	No	No	Yes
SET-TH-DWDM	Sets optical thresholds. See SET-TH-DWDM.	No	Yes	Yes
SET-TH-ENV	Sets power-bus thresholds. See SET-TH-ENV.	No	Yes	Yes
SET-TH-EQPT	Sets general thresholds. See SET-TH-EQPT.	No	Yes	Yes
STA-LOCL-RST	Resets all parameters to manufacturer's default values. See STA-LOCL-RST.	No	No	Yes

9.7 TL1 Commands and Autonomous Messages

9.7.1 ACT-USER

Command: ACT-USER

Description: Activates user session (login).

Syntax:

ACT-USER:[<tid>]:<uid>:<ctag>::<pid>;

Example 9-1 ACT-USER Command

Amp01:ONS15216 EDFA2> ACT-USER:Amp01:JOE:123::***;




Table 9-9 ACT-USER Syntax Description 

Parameter	Syntax	Description
uid	string	The user's identifier (user name). Can be any combination of up to 10 alphanumeric characters.
pid	string	The user's private identifier (password). The password must be a string of up to 10 characters, where at least 2 are non-alphabetic characters and at least 1 is a special character. Special characters are +, #, %, etc. (defined in Telcordia GR-831-CORE).

9.7.2 ALW-MSG-ALL

Command: ALW-MSG-ALL

Description: Permits or resumes the dispatch of automatic messages from the ONS 15216 EDFA2 that were inhibited by an INH-MSG call. All alarms in existence at the time that this command restores them are transmitted via REPT ALM and REPT EVT messages.

Syntax:

ALW-MSG-ALL:[<tid>]::<ctag>::[<ntfcncde>],[<condtype>][,];

Example 9-2 ALW-MSG-ALL Command

Amp01:ONS15216 EDFA2> ALW-MSG-ALL:Amp01::123::MJ,LOS;




Table 9-10 ALW-MSG-ALL Syntax Description 

Parameter	Syntax	Description
ntfncde		Notification code of the alarm or event that is to be allowed (maps to cerent15216EdfaAlarmPriority for active alarms). A null maps to none of the codes, i.e., with a null, all existing ntfncde inhibitions are kept unchanged. Possible values are:
	MJ	Major alarm.
	MN	Minor alarm.
	NA	No alarm.
	CL	Cleared alarm.
condtype		Condition type of the alarm or event that is to be allowed. (Maps to cerent15216EdfaLogEventID.) ALL maps to all types. A null maps to none of the types, i.e., with a null, all existing condtype inhibitions are kept unchanged. Possible condtype and corresponding conddescr (in quotes) are:
	LOS	"Loss of Signal" (input power) alarm (cerent15216EdfaAlarmLpin).
	GAIN	"Gain Out of Range" alarm (cerent15216EdfaAlarmGain).
	LPOUT	"Loss of Output Power" alarm (cerent15216EdfaAlarmLpout).
	CTMP	"Case Temperature Out of Range" alarm (cerent15216EdfaAlarmCtmp).
	LCRNT1	"Excessive Pump1 Current" alarm (cerent15216EdfaAlarmLcrnt1).
	LCRNT2	"Excessive Pump2 Current" alarm (cerent15216EdfaAlarmLcrnt2).
	LTMP1	"Excessive Pump1 Temperature" alarm (cerent15216EdfaAlarmLtmp1).
	LTMP2	"Excessive Pump2 Temperature" alarm (cerent15216EdfaAlarmLtmp2).
	POWERBUSA	"Power Bus A (voltage) Alarm" (cerent15216EdfaAlarmPowerBusA).
	POWERBUSB	"Power Bus B (voltage) Alarm" (cerent15216EdfaAlarmPowerBusB).
	CTRLMODE1	"Pump1 Control Mode Changed" (cerent15216EdfaControlMode for cerent15216EdfaPumpCfgPumpNumber=1).
	CTRLMODE2	"Pump2 Control Mode Changed" (cerent15216EdfaControlMode for cerent15216EdfaPumpCfgPumpNumber=2).
	GAINCHGD	"Overall Gain Changed" (cerent15216EdfaConstGainOverallGain).
	LOSHYSTCHGD	"LOS (loss of signal) Hysteresis Changed" (cerent15216EdfaLOSHysteresis).
	LOSTHCHGD	"LOS (loss of signal) Threshold Changed" (cerent15216EdfaLOSThreshold).
	LPOUTCHGD	"Loss of Output Power Setpoint Changed" (cerent15216EdfaLpoutSetpoint).
	LPOUTDEVCHGD	"Lpout (loss of output power) Deviation Changed" (cerent15216EdfaLpoutDeviation).
	LPOUTHYSTCHGD	"Lpout (loss of output power) Hysteresis Changed" (cerent15216EdfaLpoutHysteresis).
	PREATTCHGD	"Pre-attenuation Changed" (cerent15216EdfaVariableGainPreAttenuation).
	PWRBUSMAXCHGD	"Power Bus Max (voltage) Changed" (cerent15216EdfaPowerBusDCVoltageMax).
	PWRBUSMINCHGD	"Power Bus Min (voltage) Changed" (cerent15216EdfaPowerBusDCVoltageMin).
	PWRBUSMODE	"Power Bus Mode Changed" (cerent15216EdfaPowerBusMode).
	MAXCTMPCHGD	"Max Case Temperature Changed" (cerent15216EdfaCtmpMax).
	MAXCTMPHYSTCHGD	"Max Ctmp (case temperature) Hysteresis Changed" (cerent15216EdfaCtmpMaxHysteresis).
	MINCTMPCHGD	"Min Case Temperature Changed" (cerent15216EdfaCtmpMin).
	MINCTMPHYSTCHGD	"Min Ctmp (case temperature) Hysteresis Changed" (cerent15216EdfaCtmpMinHysteresis).
	CUTOVERRESET	(Software) "Reset after Cutover" (cerent15216EdfaOpCutover).
	SOFTWARELOAD	(New) "Software Load" (cerent15216EdfaOpLoad).
	SOFTWARERESET	"Software Reset" (cerent15216EdfaOpReset).
	ALL	All condtype preceding.

9.7.3 APPLY

Command: APPLY

Description: Applies a software cutover in the memory. There are two boot file entries. This command exchanges boot file entries 1 and 2 so that when the system is restarted (by the INIT-SYS command), it boots with the image that was (before the execution of this command) at the second entry.

Syntax:

APPLY:[<tid>]::<ctag>;

Example 9-3 APPLY Command

Amp01:ONS15216 EDFA2> APPLY:Amp01::1234;

9.7.4 CANC-USER

Command: CANC-USER

Description: Cancels user session (logoff).

Syntax:

CANC-USER:[<tid>]:<uid>:<ctag>;

Example 9-4 CANC-USER Command

Amp01:ONS15216 EDFA2> CANC-USER:Amp01:JOE:100;




Table 9-11 CANC-USER Syntax Description 

Parameter	Syntax	Description
uid	string	The user's identifier (user name).

9.7.5 COPY-RFILE

Command: COPY-RFILE

Description: Copies a local or remote file to the persistent memory (flash file system) on the ONS 15216 EDFA2. Depending on the value specified for the TYPE parameter, this command can be used to download a remote software image file to the ONS 15216 EDFA2 as its second boot entry (to cutover-upgrade later using the APPLY command), to copy a remote or local file to the ONS 15216 EDFA2 flash file system, or to copy a file on the ONS 15216 EDFA2 flash file system to a remote or local file. There may be a delay while this command executes. See REPT EVT FXFR for information on the autonomous response messages.

Syntax:

COPY-RFILE:[<tid>]::<ctag>::TYPE=<type>,SRC=<src>,[DEST=<dest>],[OVERWRITE=<overwrite>];

Example 9-5 COPY-RFILE Command and Response

Amp01:ONS15216 EDFA2> COPY-RFILE:Amp01::1234::TYPE=SWDL,SRC="ftp://user1:passwd@192.168.85 .10:21/bin/15216EdfaSw_2.1.0",DEST="file://localhost/15216EdfaSw_2.1.0",OVERWRITE=YES;

   Amp01 2002-04-30 11:34:05

M 100 COMPLD

/* COPY-RFILE */

;

   Amp01 2002-04-30 11:34:05

A 7 REPT EVT FXFR

EQPT:15216EdfaSw_2.1.0,START,,

;

   Amp01 2002-04-30 11:35:24

A 8 REPT EVT FXFR

EQPT:15216EdfaSw_2.1.0,COMPLD,SUCCESS,2013987

;




Table 9-12 COPY-RFILE Syntax Description 

Parameter	Syntax	Description
type		Specifies the type and direction of transfer. Possible values are:
	RFR	Restore a file from remote server to the ONS 15216 EDFA2's flash file system.
	RFBU	Backup a file from the ONS 15216 EDFA2's flash file system to the remote server (overwrite is always YES for this type).
	SWDL	Download a software image file to the ONS 15216 EDFA2's flash file system and update the second boot entry to point to this file.
src, dest	string	src and dest must both be URLs. Both FTP and file URLs are supported. An FTP URL has the following format: ftp:[//[<userid>[:<password>]@]<ftphost>[:<port>]]/<urlpath> A file URL (referring to the local system) has the following format: file://localhost/<urlpath> where <userid> is the FTP user identifier <password> is the FTP password for the user <ftphost> is the IP address of the FTP server <port> is the port number to connect to <urlpath> is the path in the following format: <cwd1>/<cwd2>/.../<cwdn>/<filename> where <cwd1>...<cwdn> are directory levels and <filename> is the file name
overwrite		Possible values are:
	YES	Overwrite existing file of the same name at the destination.
	NO	Do not overwrite if file with same name exists at the destination. This is the default if overwrite is null.

9.7.6 CPY-MEM

Command: CPY-MEM

Description: Copies the log file in the non-persistent memory (RAM) or a specified file on the persistent memory (flash file system) to a file with a specified name on the persistent memory.

Syntax:

CPY-MEM:[<tid>]::<ctag>::[<fromfile>],[<fromdev>],[<tofile>];

Example 9-6 CPY-MEM Command and Response (Copy LOG File from RAM as aolog.txt on FFS)

Amp01:ONS15216 EDFA2> CPY-MEM:Amp01::123::LOG,MEM,;

   Amp01 2002-07-16 09:49:01

M 123 COMPLD

   /* CPY-MEM */

;

Example 9-7 CPY-MEM Command and Response (Copy LOG File from RAM as aolog.txt on FFS using Null)

Amp01:ONS15216 EDFA2> CPY-MEM:Amp01::123::,,;

   Amp01 2002-07-16 09:46:01

M 123 COMPLD

   /* CPY-MEM */

;

Example 9-8 CPY-MEM Command and Response (Copy aolog.txt on FFS as logfile20020716.txt on FFS)

Amp01:ONS15216 EDFA2> CPY-MEM:Amp01::123::aolog.txt,FFS,logfile20020716;

   Amp01 2002-07-16 09:50:38

M 123 COMPLD

   /* CPY-MEM */

;




 

Table 9-13 CPY-MEM Syntax Description 

Parameter	Syntax	Description
fromfile		Name of the source file. A null means LOG. Can be null only when fromdev is also null.
	LOG	ONS 15216 EDFA2 system log file, only when fromdev is specified to be MEM or null.
	any other string	The name of the source file when fromdev is specified to be FFS. If fromdev is specified to be MEM or null, any string other than LOG is invalid. File names are case sensitive.
fromdev		Device on which the source file exists. A null means MEM. Possible values are:
	MEM	ONS 15216 EDFA2 non-persistent memory (RAM).
	FFS	ONS 15216 EDFA2 persistent memory (flash file system).
tofile	string	The name string of the destination file. A null value is valid only when fromfile is LOG or null and fromdev is MEM or null. When null is valid, the system log file (LOG) is saved as aolog.txt. File names are case sensitive. If copying from RAM (MEM) and the destination file name already exists, the destination file is overwritten. If copying from FFS and the destination file name already exists, the execution fails.

9.7.7 DLT-RFILE

Command: DLT-RFILE

Description: Deletes a file from the flash file system (FFS) of the ONS 15216 EDFA2.

Syntax:

DLT-RFILE:[<tid>]::<ctag>::FILE=<localfilename>;

Example 9-9 DLT-RFILE Command

Amp01:ONS15216 EDFA2> DLT-RFILE:Amp01::1234::FILE=snmp.cfg;




Table 9-14 DLT-RFILE Syntax Description 

Parameter	Syntax	Description
localfilename	string	Name of the file on the flash file system of the ONS 15216 EDFA2 that is to be deleted. File names are case sensitive.

9.7.8 DLT-USER-SECU

Command: DLT-USER-SECU

Description: Deletes (removes) an existing user from the system.

Syntax:

DLT-USER-SECU:[<tid>]:<uid>:<ctag>;

Example 9-10 DLT-USER-SECU Command

Amp01:ONS15216 EDFA2> DLT-USER-SECU:Amp01:jsmith:123;




Table 9-15 DLT-USER-SECU Syntax Description 

Parameter	Syntax	Description
uid	string	The user identifier (user name) of the existing user to be removed.

9.7.9 ED-DAT

Command: ED-DAT

Description: Edits the date and/or time of the ONS 15216 EDFA2.

Syntax:

ED-DAT:[<tid>]::<ctag>::<utcdate>,<utctime>;

Example 9-11 ED-DAT Command

Amp01:ONS15216 EDFA2> ED-DAT:Amp01::123::2001-12-18,02-24-55;




Table 9-16 ED-DAT Syntax Description 

Parameter	Syntax	Description
utcdate	yyyy-mm-dd	Change date to this value in universal coordinated time (UTC), which is the same as Greenwich Mean Time (GMT) Modifies cerent15216EdfaRtcDateAndTimeGMTString. Can not be null if utctime is also null.
utctime	hh-mm-ss	Change time to this value in universal coordinated time (UTC), which is the same as Greenwich Mean Time (GMT). (A time zone can not be set using TL1.) Modifies cerent15216EdfaRtcDateAndTimeGMTString. Can not be null if utcdate is also null.

9.7.10 ED-DWDM

Command: ED-DWDM

Description: Configures the ONS 15216 EDFA2 optical control parameters.

Syntax:

ED-DWDM:[<tid>]:<aid>:<ctag>:::[PUMP1CTRLMODE=<pump1ctrlmode>],[PUMP1CTRLVALUE=<pump1ctrlv alue>],[PUMP2CTRLMODE=<pump2ctrlmode>],[PUMP2CTRLVALUE=<pump2ctrlvalue>],[OVERALLGAIN=<gai n>],[PREATT=<preatt>];

Example 9-12 ED-DWDM Command

Amp01:ONS15216 EDFA2> ED-DWDM:Amp01:ALL:123:::PUMP1CTRLMODE=GAINTEMP;




Table 9-17 ED-DWDM Syntax Description 

Parameter	Syntax	Description
aid	1 ALL	1 and ALL have same input effect.
pump1ctrlmode, pump2ctrlmode		Pump 1 or pump 2 control mode (maps to cerent15216EdfaPumpCfgControlMode for the corresponding pump). Generally, pump1ctrlmode and pump2ctrlmode must be the same value. One exception is OPWR which is not valid for pump 1 and can only be set for pump 2. Possible values are:
	CRNT	Constant Pump Current mode (cerent15216EdfaPumpCfgControlMode set to constCurrent). Must set pump 1 and pump 2 to this mode at the same time.
	PWR	Constant Pump Power mode (cerent15216EdfaPumpCfgControlMode set to constPower). Must set Pump 1 and Pump 2 to this mode at the same time.
	OPWR	Constant Output Power mode (cerent15216EdfaPumpCfgControlMode set to constOutputPower). This is not a valid mode for pump 1. If pump 2 is set to OPWR, pump 1 gets automatically set to PWR with a value of 75 mW.
	GAINTEMP	Constant Gain Temperature Compensated mode (manufacturer default) (cerent15216EdfaPumpCfgControlMode set to constGainTempComp). If one pump is set to GAINTEMP, the other pump automatically gets set to GAINTEMP also.
pump1ctrlvalue, pump2ctrlvalue		Pump 1 or pump 2 control value. This value's interpretation depends on the control mode of the corresponding pump. Command fails if control mode is GAINTEMP. Possible values are:
	0 - 300	Current value in mA when mode is CRNT (sets cerent15216EdfaPumpCfgConstPumpCurrent). The default value is 0. Must set pump 1 and pump 2 at the same time.
	0 - 100	Pump power in mW when mode is PWR (sets cerent15216EdfaPumpCfgConstPumpPower). The default value is 0. Must set pump 1 and pump 2 at the same time.
	0 - 650	Output power in units of 10 mW when mode is OPWR (sets cerent15216EdfaPumpCfgConstOutPower). The default value is 0.
gain	130 - 220	Value of gain in units of 10 dB when mode is GAINTEMP (sets cerent15216EdfaConstGainOverallGain).
preatt	10 - 100	Gain pre-attenuation value in units of 10 dB when mode is other than GAINTEMP (sets cerent15216EdfaVariableGainPreAttenuation).

9.7.11 ED-ENV

Command: ED-ENV

Description: Configures the ONS 15216 EDFA2 environmental (power bus) parameters.

Syntax:

ED-ENV:[<tid>]:<aid>:<ctag>:::PWRBUSMODE=<pwrbusmode>;

Example 9-13 ED-ENV Command

Amp01:ONS15216 EDFA2> ED-ENV:Amp01:ALL:123:::PWRBUSMODE=SIMPLEX;




Table 9-18 ED-ENV Syntax Description 

Parameter	Syntax	Description
aid	PWR-A PWR-B ALL	PWR-A, PWR-B, and ALL have same input effect.
pwrbusmode		Power bus mode. Possible values are:
	SIMPLEX	Simplex mode. Requires power only to bus A. Sets cerent15216EdfaPowerBusMode to simplex.
	DUPLEX	Duplex mode (default). Requires power to both bus A and bus B. Sets cerent15216EdfaPowerBusMode to duplex.

9.7.12 ED-NE-GEN

Command: ED-NE-GEN

Description: Edit general parameters of the ONS 15216 EDFA2. Edits ONS 15216 EDFA2's sid (source identifier)/tid (target identifier), IP address, IP mask, and IP address of the default router. The ONS 15216 EDFA2 needs to be manually rebooted for the changes to take effect. (Use the INI-SYS command to manually reboot after changing parameters.) Also edits the boot table content: to return to the TL1 shell from the ASH shell, use the ASH command shell type modify tl1 (step 3. in "Log In via EIA/TIA-232 Port Using HyperTerminal" section on page 8-1).

Syntax:

ED-NE-GEN:[<tid>]::<ctag>:::[NAME=<name>],[IPADDR=<ipaddr>],[IPMASK=<ipmask>],[DEFRTR=<def rtr>],[BOOTRECORDTYPE1=<bootrectype1>],[BOOTFILENAME1=<bootfilename1>],[BOOTIPADDR1=<booti paddr1>],[BOOTRECORDTYPE2=<bootrectype2>],[BOOTFILENAME2=<bootfilename2>],[BOOTIPADDR2=<bo otipaddr2>],[CLI=<cli>];

Example 9-14 ED-NE-GEN Command

Amp01:ONS15216 EDFA2> ED-NE-GEN:Amp01::123:::NAME=Amp01,IPADDR=192.167.3.4,IPMASK=255.255. 255.0,DEFRTR=192.167.3.20,BOOTRECORDTYPE2=TFTP,BOOTFILENAME2=15216EdfaSw_1.4.0,BOOTIPADDR2 =192.168.3.4,CLI=ASH;




Table 9-19 ED-NE-GEN Syntax Description 

Parameter	Syntax	Description
name	string	System's sid/tid name.
ipaddr	string	IP address of the system (cerent15216EdfaSromIpMgmtEnetAddress).
ipmask	string	Subnet mask of the system (cerent15216EdfaSromIpMgmtEnetSubNetMask).
defrtr	string	IP address of the default router (cerent15216EdfaSromIpMgmtDefaultRouterAddress).
bootrectype1		Boot record type (cerent15216EdfaBootType for first entry). Possible values are:
	FLASH	Boot from flash.
	TFTP	Boot through TFTP.
bootfilename1	string	Boot file name (cerent15216EdfaBootFileName for first entry). File names are case sensitive.
bootipaddr1	string	IP address to boot from if bootrectype1 is set to TFTP (cerent15216EdfaBootIpAddress for first entry).
bootrectype2		Boot record type (cerent15216EdfaBootType for second entry). Possible values are:
	FLASH	Boot from flash.
	TFTP	Boot through TFTP.
bootfilename2	string	Boot file name (cerent15216EdfaBootFileName for second entry). File names are case sensitive.
bootipaddr2	string	IP address to boot from if bootrectype2 is set to TFTP (cerent15216EdfaBootIpAddress for second entry).
cli		Default type of command line interface for all EIA/TIA-232 and default telnet port user sessions with the ONS 15216 EDFA2. Possible values are:
	TL1	TL1shell interface (manufacturer default).
	ASH	ASH shell interface - ONS 15216 EDFA2's native interface.

9.7.13 ED-PID

Command: ED-PID

Description: Edits password.

Syntax:

ED-PID:[<tid>]:<uid>:<ctag>::<oldpid>,<newpid>;

Example 9-15 ED-PID Command

Amp01:ONS15216 EDFA2> ED-PID:Amp01:JOE:123::OLDPW,NEWPW;




Table 9-20 ED-PID Syntax Description 

Parameter	Syntax	Description
uid	string	The user's identifier (user name).
oldpid	string	The user's old password.
newpid	string	The user's new private identifier (password). Must be a string of up to 10 characters, where at least 2 are non-alphabetic characters and at least 1 is a special character. Special characters are +, #, %, etc. (defined in Telcordia GR-831-CORE).

9.7.14 ED-USER-SECU

Command: ED-USER-SECU

Description: Edits the user identifier, password and access level of an existing user. Per TR-835, only those data parameters that are to be edited are entered while those that are unaffected are omitted. If any position-defined parameter is omitted, a comma is to be used as the delimiter.

Syntax:

ED-USER-SECU:[<tid>]:<uid>:<ctag>::<newuid>,<pid>,,<al>[:];

Example 9-16 ED-USER-SECU Command

Amp01:ONS15216 EDFA2> ED-USER-SECU:Amp01:jsmith:123::johnsmith,****,,RW;




Table 9-21 ED-USER-SECU Syntax Description 

Parameter	Syntax	Description
uid	string	The user identifier (user name) of the existing user whose parameters are being modified.
newuid	string	New user identifier (user name) for the existing user. Can be any combination of up to 10 alphanumeric characters.
pid	string	The user's new private identifier (password). Must be a string of up to 10 characters, where at least 2 are non-alphabetic characters and at least 1 is a special character. Special characters are +, #, %, etc. (defined in Telcordia GR-831-CORE).
al		New access level of the user. See "Summary of Security Permissions for TL1 Commands" section for access level permissions.
	R	Read only privileges.
	RW	Read and write privileges.
	RWA	Read, write, and administrative privileges.

9.7.15 ENT-USER-SECU

Command: ENT-USER-SECU

Description: Creates a new user in the system; specifies the user identifier, password and access level of the new user.

Syntax:

ENT-USER-SECU:[<tid>]:<uid>:<ctag>::<pid>,,<al>[:];

Example 9-17 ENT-USER-SECU Command

Amp01:ONS15216 EDFA2> ENT-USER-SECU:Amp01:jsmith:123::****,,RW;




Table 9-22 ENT-USER-SECU Syntax Description 

Parameter	Syntax	Description
uid	string	The user identifier (user name) of the new user being created. Can be any combination of up to 10 alphanumeric characters.
pid	string	The user's private identifier (password). Must be a string of up to 10 characters, where at least 2 are non-alphabetic characters and at least 1 is a special character. Special characters are +, #, %, etc. (defined in Telcordia GR-831-CORE).
al		Access level of the user. See "Summary of Security Permissions for TL1 Commands" section for access level permissions.
	R	Read only privileges.
	RW	Read and write privileges.
	RWA	Read, write, and administrative privileges.

9.7.16 INH-MSG-ALL

Command: INH-MSG-ALL

Description: Prohibits the dispatch of some automatic messages from the ONS 15216 EDFA2 as specified in the parameters. Does not affect response from RTRV commands.

Syntax:

INH-MSG-ALL:[<tid>]::<ctag>::[<ntfcncde>],[<condtype>][,];

Example 9-18 INH-MSG-ALL Command

Amp01:ONS15216 EDFA2> INH-MSG-ALL:Amp01::123::MJ,LOS;




Table 9-23 INH-MSG-ALL Syntax Description 

Parameter	Syntax	Description
ntfncde		Notification code of the alarm or event that is to be inhibited (maps to cerent15216EdfaAlarmPriority for active alarms). A null maps to none of the codes, i.e., with a null, all existing ntfncde allowances are kept unchanged. Possible values are:
	MJ	Major alarm.
	MN	Minor alarm.
	NA	No alarm.
	CL	Cleared alarm.
condtype		Condition type of the alarm or event that is to be inhibited (maps to cerent15216EdfaLogEventID). ALL maps to all types. A null maps to none of the types, i.e., with a null, all existing condtype allowances are kept unchanged. Possible condtype and corresponding conddescr (in quotes) are:
	LOS	"Loss of Signal" (input power) alarm (cerent15216EdfaAlarmLpin).
	GAIN	"Gain Out of Range" alarm (cerent15216EdfaAlarmGain).
	LPOUT	"Loss of Output Power" alarm (cerent15216EdfaAlarmLpout).
	CTMP	"Case Temperature Out of Range" alarm (cerent15216EdfaAlarmCtmp).
	LCRNT1	"Excessive Pump1 Current" alarm (cerent15216EdfaAlarmLcrnt1).
	LCRNT2	"Excessive Pump2 Current" alarm (cerent15216EdfaAlarmLcrnt2).
	LTMP1	"Excessive Pump1 Temperature" alarm (cerent15216EdfaAlarmLtmp1).
	LTMP2	"Excessive Pump2 Temperature" alarm (cerent15216EdfaAlarmLtmp2).
	POWERBUSA	"Power Bus A (voltage) Alarm" (cerent15216EdfaAlarmPowerBusA).
	POWERBUSB	"Power Bus B (voltage) Alarm" (cerent15216EdfaAlarmPowerBusB).
	CTRLMODE1	"Pump1 Control Mode Changed" (cerent15216EdfaControlMode for cerent15216EdfaPumpCfgPumpNumber=1).
	CTRLMODE2	"Pump2 Control Mode Changed" (cerent15216EdfaControlMode for cerent15216EdfaPumpCfgPumpNumber=2).
	GAINCHGD	"Overall Gain Changed" (cerent15216EdfaConstGainOverallGain).
	LOSHYSTCHGD	"LOS (loss of signal) Hysteresis Changed" (cerent15216EdfaLOSHysteresis).
	LOSTHCHGD	"LOS (loss of signal) Threshold Changed" (cerent15216EdfaLOSThreshold).
	LPOUTCHGD	"Loss of Output Power Setpoint Changed" (cerent15216EdfaLpoutSetpoint).
	LPOUTDEVCHGD	"Lpout (loss of output power) Deviation Changed" (cerent15216EdfaLpoutDeviation).
	LPOUTHYSTCHGD	"Lpout (loss of output power) Hysteresis Changed" (cerent15216EdfaLpoutHysteresis).
	PREATTCHGD	"Pre-attenuation Changed" (cerent15216EdfaVariableGainPreAttenuation).
	PWRBUSMAXCHGD	"Power Bus Max (voltage) Changed" (cerent15216EdfaPowerBusDCVoltageMax).
	PWRBUSMINCHGD	"Power Bus Min (voltage) Changed" (cerent15216EdfaPowerBusDCVoltageMin).
	PWRBUSMODE	"Power Bus Mode Changed" (cerent15216EdfaPowerBusMode).
	MAXCTMPCHGD	"Max Case Temperature Changed" (cerent15216EdfaCtmpMax).
	MAXCTMPHYSTCHGD	"Max Ctmp (case temperature) Hysteresis Changed" (cerent15216EdfaCtmpMaxHysteresis).
	MINCTMPCHGD	"Min Case Temperature Changed" (cerent15216EdfaCtmpMin).
	MINCTMPHYSTCHGD	"Min Ctmp (case temperature) Hysteresis Changed" (cerent15216EdfaCtmpMinHysteresis).
	CUTOVERRESET	(Software) "Reset after Cutover" (cerent15216EdfaOpCutover).
	SOFTWARELOAD	(New) "Software Load" (cerent15216EdfaOpLoad).
	SOFTWARERESET	"Software Reset" (cerent15216EdfaOpReset).
	ALL	All condtype preceding.

9.7.17 INIT-SYS

Command: INIT-SYS

Description: Reboots the system.

Syntax:

INIT-SYS:[<tid>]:<aid>:<ctag>::<ph>;

Example 9-19 INIT-SYS Command

Amp01:ONS15216 EDFA2> INIT-SYS:Amp01:ALL:1234::1;




Table 9-24 INIT-SYS Syntax Description 

Parameter	Syntax	Description
aid	string EQPT ALL	EQPT and ALL have same input effect.
ph	integer 1	Level of initialization. Always 1.

9.7.18 REPT ALM DWDM

Command: REPT ALM DWDM

Description: Reports when a DWDM alarm is logged or cleared (derived from cerent15216EdfaAlarmState).

---

Note The REPT ALM DWDM messages for Loss of Signal, Gain Out of Range, and Loss of Output Power are prioritized (in the order just listed) so that only one message can be delivered at one time. For example, if the ONS 15216 EDFA2 detects both a loss of input signal and a loss of output power at the same time, it will deliver only the Loss of Signal message to the user. This prioritized filtering of alarms does not occur with the SNMP delivery of alarms of the ONS 15216 EDFA2.

---

Syntax:

   <sid> <date> <time>

<almcde> <atag> REPT ALM DWDM

   "<aid>:<ntfcncde>,<condtype>,<srveff>,<ocrdat>,<ocrtm>,,:<conddescr>"

;

Example 9-20 REPT ALM DWDM Message

   Amp01 2001-06-18 14:50:44

** 142 REPT ALM DWDM

   "1:MJ,LOS,SA,6-18,14-50-44,,:\"Loss Of Signal\""

;




Table 9-25 REPT ALM DWDM Syntax Description 

Parameter	Syntax	Description
time	hh:mm:ss	Time of origination of TL1 message.
almcde		The alarm severity code for the TL1 message. Possible values are:
	**	Major alarm.
	*	Minor alarm.
	A	No alarm. Occurs only when ntfncde is NA.
atag	0 - 999	An integer between 0 and 999 used as a sequence number in autonomous messages.
aid		Always 1.
	1	Directly affecting the optical signal.
conddescr		Detailed text description of the event. The conddescr is 1 to 64 characters of ASCII text. See condtype below.
condtype		Condition type identifies the type of alarm (maps to cerent15216EdfaLogEventID). Possible condtype and corresponding conddescr (in quotes) are:
	LOS	"Loss of Signal" (input power) alarm (cerent15216EdfaAlarmLpin).
	GAIN	"Gain Out of Range" alarm (cerent15216EdfaAlarmGain).
	LPOUT	"Loss of Output Power" alarm (cerent15216EdfaAlarmLpout).
date	yyyy-mm-dd	Date of origination of TL1 message.
ntfncde		Notification code (maps to cerent15216EdfaAlarmPriority). Possible values are:
	MJ	Major alarm.
	MN	Minor alarm.
	CL	Cleared alarm.
	NA	No alarm.
ocrdat	m-d	Date (month-day) of the event occurrence (derived from cerent15216EdfaDateAndTimeString).
ocrtm	h-m-s	Time (hour-minute-second) of the event occurrence (derived from cerent15216EdfaDateAndTimeString).
sid	string	Source identifier uniquely identifies the source of a TL1 autonomous command.
srveff		Effect on service. Possible values are:
	SA	Service affecting.
	NSA	Non-service affecting.

9.7.19 REPT ALM ENV

Command: REPT ALM ENV

Description: Reports when a power bus alarm is logged or cleared (derived from cerent15216EdfaAlarmState).

Syntax:

   <sid> <date> <time>

<almcde> <atag> REPT ALM ENV

   "<aid>:<ntfcncde>,<condtype>,<ocrdat>,<ocrtm>,<conddescr>"

;

Example 9-21 REPT ALM ENV Message

   Amp01 2001-06-18 14:48:44

** 141 REPT ALM ENV

   "PWR-A:MJ,PWRBUSA,6-18,14-48-44,\"Power Bus A Alarm\""

;




Table 9-26 REPT ALM ENV Syntax Description 

Parameter	Syntax	Description
almcde		The alarm severity code for the TL1 message. Possible values are:
	**	Major alarm.
	*	Minor alarm.
	A	No alarm. Occurs only when ntfncde is NA.
atag	0 - 999	An integer between 0 and 999 used as a sequence number in autonomous messages .
aid		Possible values are:
	PWR-A	Affecting Power Bus A (or both A and B).
	PWR-B	Affecting Power Bus B.
conddescr		Detailed text description of the event. The conddescr is 1 to 64 characters of ASCII text. See condtype below.
condtype		Condition type identifies the type of alarm (maps to cerent15216EdfaLogEventID). Possible condtype and corresponding conddescr (in quotes) are:
	PWRBUSA	"Power Bus A (voltage) Alarm" (cerent15216EdfaAlarmPowerBusA).
	PWRBUSB	"Power Bus B (voltage) Alarm" (cerent15216EdfaAlarmPowerBusB).
date	yyyy-mm-dd	Date of origination of TL1 message.
ntfncde		Notification code (maps to cerent15216EdfaAlarmPriority). Possible values are:
	MJ	Major alarm.
	MN	Minor alarm.
	CL	Cleared alarm.
	NA	No alarm.
ocrdat	m-d	Date (month-day) of the event occurrence (derived from cerent15216EdfaDateAndTimeString).
ocrtm	h-m-s	Time (hour-minute-second) of the event occurrence (derived from cerent15216EdfaDateAndTimeString).
sid	string	Source identifier uniquely identifies the source of a TL1 autonomous command.
time	hh:mm:ss	Time of origination of TL1 message.

9.7.20 REPT ALM EQPT

Command: REPT ALM EQPT

Description: Reports when a general alarm (not directly affecting optical signal or power bus) is logged or cleared (derived from cerent15216EdfaAlarmState).

Syntax:

   <sid> <date> <time>

<almcde> <atag> REPT ALM EQPT

   "<aid>:<ntfcncde>,<condtype>,<srveff>,<ocrdat>,<ocrtm>,,:<conddescr>"

;

Example 9-22 REPT ALM EQPT Message

   Amp01 2001-06-18 14:48:44

* 141 REPT ALM EQPT

   "EQPT:MN,LCRNT1,NSA,6-18,14-48-44,,:\"Excessive Pump1 Current\""

;




Table 9-27 REPT ALM EQPT Syntax Description 

Parameter	Syntax	Description
almcde		The alarm severity code for the TL1 message. Possible values are:
	**	Major alarm.
	*	Minor alarm.
	A	No alarm. Occurs only when ntfncde is NA.
atag	0 - 999	An integer between 0 and 999 used as a sequence number in autonomous messages .
aid		Always EQPT.
	EQPT	General parameters of the ONS 15216 EDFA2 (not directly affecting optical signal or power bus).
conddescr		Detailed text description of the event. The conddescr is 1 to 64 characters of ASCII text. See condtype below.
condtype		Condition type identifies the type of alarm (maps to cerent15216EdfaLogEventID). Possible condtype and corresponding conddescr (in quotes) are:
	CTMP	"Case Temperature Out of Range" alarm (cerent15216EdfaAlarmCtmp).
	LCRNT1	"Excessive Pump1 Current" alarm (cerent15216EdfaAlarmLcrnt1).
	LCRNT2	"Excessive Pump2 Current" alarm (cerent15216EdfaAlarmLcrnt2).
	LTMP1	"Excessive Pump1 Temperature" alarm (cerent15216EdfaAlarmLtmp1).
	LTMP2	"Excessive Pump2 Temperature" alarm (cerent15216EdfaAlarmLtmp2).
date	yyyy-mm-dd	Date of origination of TL1 message.
ntfncde		Notification code (maps to cerent15216EdfaAlarmPriority). Possible values are:
	MJ	Major alarm.
	MN	Minor alarm.
	CL	Cleared alarm.
	NA	No alarm.
ocrdat	m-d	Date (month-day) of the event occurrence (derived from cerent15216EdfaDateAndTimeString).
ocrtm	h-m-s	Time (hour-minute-second) of the event occurrence (derived from cerent15216EdfaDateAndTimeString).
sid	string	Source identifier uniquely identifies the source of a TL1 autonomous command.
srveff		Effect on service. Possible values are:
	SA	Service affecting.
	NSA	Non-service affecting.
time	hh:mm:ss	Time of origination of TL1 message.

9.7.21 REPT EVT DWDM / REPT EVT ENV / REPT EVT EQPT

Command: REPT EVT DWDM or REPT EVT ENV or REPT EVT EQPT

Description: Reports autonomous events. Reports when an event is logged.

Syntax:

   <sid> <date> <time>

A <atag> REPT EVT <ccm>

   "<aid>:<condtype>,<condeff>,<ocrdat>,<ocrtm>,,,,:<conddescr>"

;

Example 9-23 REPT EVT DWDM Message

   Amp01 2001-06-18 14:48:44

A 141 REPT EVT DWDM

   "1:CTRLMODE1,TC,6-18,14-48-44,,,,:\"Pump1 Control Mode Changed\""

;




Table 9-28 REPT EVT DWDM / REPT EVT ENV / REPT EVT EQPT Syntax Description 

Parameter	Syntax	Description
atag	0 - 999	An integer between 0 and 999 used as a sequence number in autonomous messages .
aid		Possible values are:
	1	Directly affecting the optical signal.
	PWR-A	Affecting Power Bus A (or both A and B).
	PWR-B	Affecting Power Bus B.
	EQPT	General parameters of the ONS 15216 EDFA2 (not directly affecting optical signal or power bus).
conddescr		Detailed text description of the event. The conddescr is 1 to 64 characters of ASCII text. See condtype below.
condtype (ccm)		Condition type identifies the type of event (maps to cerent15216EdfaLogEventID). Possible condtype and corresponding conddescr (in quotes) are:
	CTRLMODE1 (DWDM)	"Pump1 Control Mode Changed" (cerent15216EdfaControlMode for cerent15216EdfaPumpCfgPumpNumber=1).
	CTRLMODE2 (DWDM)	"Pump2 Control Mode Changed" (cerent15216EdfaControlMode for cerent15216EdfaPumpCfgPumpNumber=2).
	GAINCHGD (DWDM)	"Overall Gain Changed" (cerent15216EdfaConstGainOverallGain).
	LOSHYSTCHGD (DWDM)	"LOS (loss of signal) Hysteresis Changed" (cerent15216EdfaLOSHysteresis).
	LOSTHCHGD (DWDM)	"LOS (loss of signal) Threshold Changed" (cerent15216EdfaLOSThreshold).
	LPOUTCHGD (DWDM)	"Loss of Output Power Setpoint Changed" (cerent15216EdfaLpoutSetpoint).
	LPOUTDEVCHGD (DWDM)	"Lpout (loss of output power) Deviation Changed" (cerent15216EdfaLpoutDeviation).
	LPOUTHYSTCHGD (DWDM)	"Lpout (loss of output power) Hysteresis Changed" (cerent15216EdfaLpoutHysteresis).
	PREATTCHGD (DWDM)	"Pre-attenuation Changed" (cerent15216EdfaVariableGainPreAttenuation).
	PWRBUSMAXCHGD (EVN)	"Power Bus Max (voltage) Changed" (cerent15216EdfaPowerBusDCVoltageMax).
	PWRBUSMINCHGD (EVN)	"Power Bus Min (voltage) Changed" (cerent15216EdfaPowerBusDCVoltageMin).
	PWRBUSMODE (EVN)	"Power Bus Mode Changed" (cerent15216EdfaPowerBusMode).
	MAXCTMPCHGD (EQPT)	"Max Case Temperature Changed" (cerent15216EdfaCtmpMax).
condtype (ccm)	MAXCTMPHYSTCHGD (EQPT)	"Max Ctmp (case temperature) Hysteresis Changed" (cerent15216EdfaCtmpMaxHysteresis).
	MINCTMPCHGD (EQPT)	"Min Case Temperature Changed" (cerent15216EdfaCtmpMin).
	MINCTMPHYSTCHGD (EQPT)	"Min Ctmp (case temperature) Hysteresis Changed" (cerent15216EdfaCtmpMinHysteresis).
	CUTOVERRESET (EQPT)	(Software) "Reset after Cutover" (cerent15216EdfaOpCutover).
	SOFTWARELOAD (EQPT)	(New) "Software Load" (cerent15216EdfaOpLoad).
	SOFTWARERESET (EQPT)	"Software Reset" (cerent15216EdfaOpReset).
condeff	string TC	Effect of the condition. Always TC (transient condition).
date	yyyy-mm-dd	Date of origination of TL1 message.
ocrdat	m-d	Date (month-day) of the event occurrence (derived from cerent15216EdfaDateAndTimeString).
ocrtm	h-m-s	Time (hour-minute-second) of the event occurrence (derived from cerent15216EdfaDateAndTimeString).
sid	string	Source identifier uniquely identifies the source of a TL1 autonomous command.
srveff		Effect on service. Possible values are:
	SA	Service affecting.
	NSA	Non-service affecting.
time	hh:mm:ss	Time of origination of TL1 message.

9.7.22 REPT EVT FXFR

Command: REPT EVT FXFR

Description: Reports autonomous events related to the FTP file transfer (see "COPY-RFILE" section). Reports when an event related to the file transfer is logged.

Syntax:

   <sid> <date> <time>

A <atag> REPT EVT FXFR

   "<aid>:<filename>,<fxfr_status>[,<fxfr_rslt>][,<bytes_xfrd>]"

;

Example 9-24 REPT EVT FXFR Message

   Amp01 2001-06-18 14:48:44

A 141 REPT EVT FXFR

   "EQPT:VMRLS20.EXE,COMPLD,SUCCESS,8051"

;




Table 9-29 REPT EVT FXFR Syntax Description 

Parameter	Syntax	Description
atag	0 - 999	An integer between 0 and 999 used as a sequence number in autonomous messages.
aid		Always EQPT.
	EQPT	General parameters of the ONS 15216 EDFA2 (not directly affecting optical signal or power bus).
bytes_xfrd		Total number of bytes transferred when fxfr_status is COMPLD. See fxfr_status below.
filename		Identifies the name of the file that is being transferred.
fxfr_rslt		File transfer result indicates success or failure of the file transfer. This is displayed only when the file transfer has completed (i.e., fxfr_status is COMPLD). Possible values are:
	SUCCESS	File transfer was successful.
	FAILURE	File transfer failed.
fxfr_status		File transfer status of ONS 15216 EDFA2's file transfer at the current time. (The option IP (in progress) has not been implemented.) Possible values are:
	START	File transfer has started.
	COMPLD	File transfer has completed.
date	yyyy-mm-dd	Date of origination of TL1 message.
sid	string	Source identifier uniquely identifies the source of a TL1 autonomous command.
time	hh:mm:ss	Time of origination of TL1 message.

9.7.23 RTRV-ALM-ALL

Command: RTRV-ALM-ALL

Description: Generates a report on all active alarms (except environmental (ENV) alarms as per Telcordia GR-833-CORE). Note that the ccm does not appear in the response for EQPT alarms.

---

Note The messages for Loss of Signal (LOS), Gain Out of Range (GAIN), and Loss of Output Power (LPOUT) are prioritized (in the order just listed) so that only one message can be delivered at one time. For example, if the ONS 15216 EDFA2 detects both a loss of input signal and a loss of output power at the same time, it will deliver only the Loss of Signal (LOS) message to the user. This prioritized filtering of alarms does not occur with the SNMP delivery of alarms of the ONS 15216 EDFA2.

---

Syntax:

RTRV-ALM-ALL:[<tid>]::<ctag>::[<ntfcncde>],[<condtype>],[<srveff>][,,];

   <sid> <date> <time>

M <ctag> COMPLD

   "<aid>,<ccm>:<ntfcncde>,<condtype>,<srveff>,<ocrdat>,<ocrtm>,,:<conddescr>"

;

Example 9-25 RTRV-ALM-ALL Command and Response

Amp01:ONS15216 EDFA2> RTRV-ALM-ALL:Amp01::229::MN,LCRNT1,NSA,,;

   Amp01 2002-06-20 14:30:00

M 229 COMPLD

   "1,DWDM:MJ,LOS,SA,6-20,14-25-30,,:\"Loss Of Signal\""

   "EQPT,EQPT:MN,LCRNT1,NSA,6-20,14-25-30,,:\"Excessive Pump1 Current\""

;




Table 9-30 RTRV-ALM-ALL Syntax Description 

Parameter	Syntax	Description
aid		Possible values are:
	1	Directly affecting the optical signal
	EQPT	General parameters of the ONS 15216 EDFA2 (not directly affecting optical signal or power bus)
conddescr		Detailed text description of the event. The conddescr is 1 to 64 characters of ASCII text. See condtype below
condtype (ccm)		Condition type identifies the type of alarm (maps to cerent15216EdfaLogEventID). Possible condtype and corresponding conddescr (in quotes) are:
	LOS (DWDM)	"Loss of Signal" (input power) alarm (cerent15216EdfaAlarmLpin).
	GAIN (DWDM)	"Gain Out of Range" alarm (cerent15216EdfaAlarmGain).
	LPOUT (DWDM)	"Loss of Output Power" alarm (cerent15216EdfaAlarmLpout).
	CTMP (EQPT)	"Case Temperature Out of Range" alarm (cerent15216EdfaAlarmCtmp).
	LCRNT1 (EQPT)	"Excessive Pump1 Current" alarm (cerent15216EdfaAlarmLcrnt1).
	LCRNT2 (EQPT)	"Excessive Pump2 Current" alarm (cerent15216EdfaAlarmLcrnt2).
	LTMP1 (EQPT)	"Excessive Pump1 Temperature" alarm (cerent15216EdfaAlarmLtmp1).
	LTMP2 (EQPT)	"Excessive Pump2 Temperature" alarm (cerent15216EdfaAlarmLtmp2).
date	yyyy-mm-dd	Date of origination of TL1 message.
ntfncde		Notification code (maps to cerent15216EdfaAlarmPriority). Possible values are:
	MJ	Major alarm.
	MN	Minor alarm.
	CL	Cleared alarm.
	NA	No alarm.
ocrdat	m-d	Date (month-day) of the event occurrence (derived from cerent15216EdfaDateAndTimeString).
ocrtm	h-m-s	Time (hour-minute-second) of the event occurrence (derived from cerent15216EdfaDateAndTimeString).
sid	string	Source identifier uniquely identifies the source of a TL1 autonomous command.
srveff		Effect on service. Possible values are:
	SA	Service affecting.
	NSA	Non-service affecting.
time	hh:mm:ss	Time of origination of TL1 message.

9.7.24 RTRV-ALM-DWDM

Command: RTRV-ALM-DWDM

Description: Generates a report on active DWDM alarms.

---

Note The messages for Loss of Signal (LOS), Gain Out of Range (GAIN), and Loss of Output Power (LPOUT) are prioritized (in the order just listed) so that only one message can be delivered at one time. For example, if the ONS 15216 EDFA2 detects both a loss of input signal and a loss of output power at the same time, it will deliver only the Loss of Signal (LOS) message to the user. This prioritized filtering of alarms does not occur with the SNMP delivery of alarms of the ONS 15216 EDFA2.

---

Syntax:

RTRV-ALM-DWDM:[<tid>]:<aid>:<ctag>::[<ntfcncde>],[<condtype>],[<srveff>][,,];

   <sid> <date> <time>

M <ctag> COMPLD

   "<aid>,<ccm>:<ntfcncde>,<condtype>,<srveff>,<ocrdat>,<ocrtm>,,:<conddescr>"

;

Example 9-26 RTRV-ALM-DWDM Command and Response

Amp01:ONS15216 EDFA2> RTRV-ALM-DWDM:Amp01:ALL:229::,,;

   Amp01 2002-06-20 14:30:00

M 229 COMPLD

   "1,DWDM:MJ,LOS,SA,6-20,14-25-30,,:\"Loss Of Signal\""

;




Table 9-31 RTRV-ALM-DWDM Syntax Description 

Parameter	Syntax	Description
aid		1 and ALL have same input effect.
	1	Directly affecting the optical signal.
	ALL	Any or all of the preceding (command input only).
conddescr		Detailed text description of the event. The conddescr is 1 to 64 characters of ASCII text. See condtype below.
condtype		Condition type identifies the type of alarm (maps to cerent15216EdfaLogEventID). Possible condtype and corresponding conddescr (in quotes) are:
	LOS	"Loss of Signal" (input power) alarm (cerent15216EdfaAlarmLpin).
	GAIN	"Gain Out of Range" alarm (cerent15216EdfaAlarmGain).
	LPOUT	"Loss of Output Power" alarm (cerent15216EdfaAlarmLpout).
date	yyyy-mm-dd	Date of origination of TL1 message.
ntfncde		Notification code (maps to cerent15216EdfaAlarmPriority). Possible values are:
	MJ	Major alarm.
	MN	Minor alarm.
	CL	Cleared alarm.
	NA	No alarm.
ocrdat	m-d	Date (month-day) of the event occurrence (derived from cerent15216EdfaDateAndTimeString).
ocrtm	h-m-s	Time (hour-minute-second) of the event occurrence (derived from cerent15216EdfaDateAndTimeString).
sid	string	Source identifier uniquely identifies the source of a TL1 autonomous command.
srveff		Effect on service. Possible values are:
	SA	Service affecting.
	NSA	Non-service affecting.
time	hh:mm:ss	Time of origination of TL1 message.

9.7.25 RTRV-ALM-ENV

Command: RTRV-ALM-ENV

Description: Generates a report on specific or all active environmental (power bus) alarms.

Syntax:

RTRV-ALM-ENV:[<tid>]:<aid>:<ctag>::[<ntfcncde>],[<condtype>];

   <sid> <date> <time>

M <ctag> COMPLD

   "<aid>,<ccm>:<ntfcncde>,<condtype>,<ocrdat>,<ocrtm>,<conddescr>"

;

Example 9-27 RTRV-ALM-ENV Command and Response

Amp01:ONS15216 EDFA2> RTRV-ALM-ENV:Amp01:ALL:229::MJ,PWRBUSA;

   Amp01 2002-06-20 14:30:00

M 229 COMPLD

   "PWR-A,ENV:MJ,PWRBUSA,6-20,14-25-30,\"Power Bus A Alarm\""

;




Table 9-32 RTRV-ALM-ENV Syntax Description 

Parameter	Syntax	Description
aid		Specifying PWR-A or PWR-B in input has a filter effect on the response.
	PWR-A	Affecting Power Bus A (or both A and B).
	PWR-B	Affecting Power Bus B.
	ALL	Any or all of the preceding (command input only).
conddescr		Detailed text description of the event. The conddescr is 1 to 64 characters of ASCII text. See condtype below.
condtype		Condition type identifies the type of alarm (maps to cerent15216EdfaLogEventID). Possible condtype and corresponding conddescr (in quotes) are:
	PWRBUSA	"Power Bus A (voltage) Alarm" (cerent15216EdfaAlarmPowerBusA).
	PWRBUSB	"Power Bus B (voltage) Alarm" (cerent15216EdfaAlarmPowerBusB).
date	yyyy-mm-dd	Date of origination of TL1 message.
ntfncde		Notification code (maps to cerent15216EdfaAlarmPriority). Possible values are:
	MJ	Major alarm.
	MN	Minor alarm.
	CL	Cleared alarm.
	NA	No alarm.
ocrdat	m-d	Date (month-day) of the event occurrence (derived from cerent15216EdfaDateAndTimeString).
ocrtm	h-m-s	Time (hour-minute-second) of the event occurrence (derived from cerent15216EdfaDateAndTimeString).
sid	string	Source identifier uniquely identifies the source of a TL1 autonomous command.
time	hh:mm:ss	Time of origination of TL1 message.

9.7.26 RTRV-ALM-EQPT

Command: RTRV-ALM-EQPT

Description: Generates a report on all active alarms (except environmental alarms as per Telcordia GR-833-CORE).

Syntax:

RTRV-ALM-EQPT:[<tid>]:<aid>:<ctag>::[<ntfcncde>],[<condtype>],[<srveff>][,,];

   <sid> <date> <time>

M <ctag> COMPLD

   "<aid>:<ntfcncde>,<condtype>,<srveff>,<ocrdat>,<ocrtm>,,:<conddescr>"

;

Example 9-28 RTRV-ALM-EQPT Command and Response

Amp01:ONS15216 EDFA2> RTRV-ALM-EQPT:Amp01:ALL:229::MN,LCRNT1,NSA,,;

   Amp01 2002-06-20 14:30:00

M 229 COMPLD

   "EQPT:MN,LCRNT1,NSA,6-20,14-25-30,,:\"Excessive Pump1 Current\""

;




Table 9-33 RTRV-ALM-EQPT Syntax Description 

Parameter	Syntax	Description
aid		EQPT and ALL have same input effect.
	EQPT	General parameters of the ONS 15216 EDFA2 (not directly affecting optical signal or power bus).
	ALL	Any or all of the preceding (command input only).
conddescr		Detailed text description of the event. The conddescr is 1 to 64 characters of ASCII text. See condtype below.
condtype		Condition type identifies the type of alarm (maps to cerent15216EdfaLogEventID). Possible condtype and corresponding conddescr (in quotes) are:
	CTMP	"Case Temperature Out of Range" alarm (cerent15216EdfaAlarmCtmp).
	LCRNT1	"Excessive Pump1 Current" alarm (cerent15216EdfaAlarmLcrnt1).
	LCRNT2	"Excessive Pump2 Current" alarm (cerent15216EdfaAlarmLcrnt2).
	LTMP1	"Excessive Pump1 Temperature" alarm (cerent15216EdfaAlarmLtmp1).
	LTMP2	"Excessive Pump2 Temperature" alarm (cerent15216EdfaAlarmLtmp2).
date	yyyy-mm-dd	Date of origination of TL1 message.
ntfncde		Notification code (maps to cerent15216EdfaAlarmPriority). Possible values are:
	MJ	Major alarm.
	MN	Minor alarm.
	CL	Cleared alarm.
	NA	No alarm.
ocrdat	m-d	Date (month-day) of the event occurrence (derived from cerent15216EdfaDateAndTimeString).
ocrtm	h-m-s	Time (hour-minute-second) of the event occurrence (derived from cerent15216EdfaDateAndTimeString).
sid	string	Source identifier uniquely identifies the source of a TL1 autonomous command.
srveff		Effect on service. Possible values are:
	SA	Service affecting.
	NSA	Non-service affecting.
time	hh:mm:ss	Time of origination of TL1 message.

9.7.27 RTRV-AO

Command: RTRV-AO

Description: Retrieves autonomous output.

Allows the operating system to retrieve a copy of queued autonomous messages or missing autonomous messages. Examples of autonomous messages are REPT ALM and REPT EVT.

Users can retrieve up to the latest 1000 autonomous messages (alarms and events). Normally, users should limit the retrieval to less than 200 messages to prevent alarm reporting and other active users from being impacted. To retrieve more than 200 messages, it is recommended that the user saves the autonomous message log to a file using the CPY-MEM command and then get the file through FTP using the COPY-RFILE command.

If none of the stored automatic messages satisfy the selection criteria, then a complete normal response is sent. If one or more stored autonomous messages satisfy the criteria, then the messages should be reported in the normal response in ATAG order.

Syntax:

RTRV-AO:[<tid>]::<ctag>:::[ATAGSEQ=<atagseq>][,MSGTYPE=<msgtype>];

Example 9-29 RTRV-AO Command

Amp01:ONS15216 EDFA2> RTRV-AO:Amp01::123:::ATAGSEQ=20&&30,MSGTYPE=EVT;




Table 9-34 RTRV-AO Syntax Description 

Parameter	Syntax	Description
atagseq		atag is an integer between 0 and 999 used by the ONS 15216 EDFA2 to sequentially number in autonomous messages. atagseq can be a single atag number or a range of numbers in the form AA&&BB, where AA and BB are integers. If null, the 20 latest messages will be retrieved.
msgtype		Type of message. A null value means both ALM and EVT.
	ALM	Alarm message.
	EVT	Event message.

9.7.28 RTRV-COND-ALL

Command: RTRV-COND-ALL

Description: Generates a report on the condition (state) of all alarms (except environmental alarms). Note that the ccm does not appear in the response for EQPT alarms.

---

Note The messages for Loss of Signal (LOS), Gain Out of Range (GAIN), and Loss of Output Power (LPOUT) are prioritized (in the order just listed) so that only one message can be delivered at one time. For example, if the ONS 15216 EDFA2 detects both a loss of input signal and a loss of output power at the same time, it will deliver only the Loss of Signal (LOS) message to the user. This prioritized filtering of alarms does not occur with the SNMP delivery of alarms of the ONS 15216 EDFA2.

---

Syntax:

RTRV-COND-ALL:[<tid>]::<ctag>::[<condtype>][,,];

   <sid> <date> <time>

M <ctag> COMPLD

   "<aid>,<ccm>:<ntfcncde>,<condtype>,<srveff>,<ocrdat>,<ocrtm>,,,<conddescr>"

;

Example 9-30 RTRV-COND-ALL Command and Response

Amp01:ONS15216 EDFA2> RTRV-COND-ALL:Amp01::229::LCRNT1;

   Amp01 2002-06-20 14:30:00

M 229 COMPLD

   "1,DWDM:MJ,LOS,SA,6-20,14-25-30,,,\"Loss Of Signal\""

   "EQPT,EQPT:MN,LCRNT1,NSA,6-20,14-25-30,,,\"Excessive Pump1 Current\""

;




Table 9-35 RTRV-COND-ALL Syntax Description 

Parameter	Syntax	Description
aid		Possible values are:
	1	Directly affecting the optical signal.
	EQPT	General parameters of the ONS 15216 EDFA2 (not directly affecting optical signal or power bus).
conddescr		Detailed text description of the event. The conddescr is 1 to 64 characters of ASCII text. See condtype below.
condtype (ccm)		Condition type identifies the type of alarm (maps to cerent15216EdfaLogEventID). Possible condtype and corresponding conddescr (in quotes) are:
	LOS (DWDM)	"Loss of Signal" (input power) alarm (cerent15216EdfaAlarmLpin).
	GAIN (DWDM)	"Gain Out of Range" alarm (cerent15216EdfaAlarmGain).
	LPOUT (DWDM)	"Loss of Output Power" alarm (cerent15216EdfaAlarmLpout).
	CTMP (EQPT)	"Case Temperature Out of Range" alarm (cerent15216EdfaAlarmCtmp).
	LCRNT1 (EQPT)	"Excessive Pump1 Current" alarm (cerent15216EdfaAlarmLcrnt1).
	LCRNT2 (EQPT)	"Excessive Pump2 Current" alarm (cerent15216EdfaAlarmLcrnt2).
	LTMP1 (EQPT)	"Excessive Pump1 Temperature" alarm (cerent15216EdfaAlarmLtmp1).
	LTMP2 (EQPT)	"Excessive Pump2 Temperature" alarm (cerent15216EdfaAlarmLtmp2).
date	yyyy-mm-dd	Date of origination of TL1 message.
ntfncde		Notification code (maps to cerent15216EdfaAlarmPriority). Possible values are:
	MJ	Major alarm.
	MN	Minor alarm.
	NA	No alarm.
ocrdat	m-d	Date (month-day) of the event occurrence (derived from cerent15216EdfaDateAndTimeString).
ocrtm	h-m-s	Time (hour-minute-second) of the event occurrence (derived from cerent15216EdfaDateAndTimeString).
sid	string	Source identifier uniquely identifies the source of a TL1 autonomous command.
srveff		Effect on service. Possible values are:
	SA	Service affecting.
	NSA	Non-service affecting.
time	hh:mm:ss	Time of origination of TL1 message.

9.7.29 RTRV-COND-DWDM

Command: RTRV-COND-DWDM

Description: Generates a report on the condition (state) of DWDM alarms.

---

Note The messages for Loss of Signal (LOS), Gain Out of Range (GAIN), and Loss of Output Power (LPOUT) are prioritized (in the order just listed) so that only one message can be delivered at one time. For example, if the ONS 15216 EDFA2 detects both a loss of input signal and a loss of output power at the same time, it will deliver only the Loss of Signal (LOS) message to the user. This prioritized filtering of alarms does not occur with the SNMP delivery of alarms of the ONS 15216 EDFA2.

---

Syntax:

RTRV-COND-DWDM:[<tid>]:<aid>:<ctag>::[<condtype>][,,];

   <sid> <date> <time>

M <ctag> COMPLD

   "<aid>,<ccm>:<ntfcncde>,<condtype>,<srveff>,<ocrdat>,<ocrtm>,,,<conddescr>"

;

Example 9-31 RTRV-COND-DWDM Command and Response

Amp01:ONS15216 EDFA2> RTRV-COND-DWDM:Amp01:ALL:229::LOS;

   Amp01 2002-06-20 14:30:00

M 229 COMPLD

   "1,DWDM:MJ,LOS,SA,6-20,14-25-30,,,\"Loss Of Signal\""

;




Table 9-36 RTRV-COND-DWDM Syntax Description 

Parameter	Syntax	Description
aid		1 and ALL have same input effect.
	1	Directly affecting the optical signal.
	ALL	Any or all of the preceding (command input only).
conddescr		Detailed text description of the event. The conddescr is 1 to 64 characters of ASCII text. See condtype below.
condtype		Condition type identifies the type of alarm (maps to cerent15216EdfaLogEventID). Possible condtype and corresponding conddescr (in quotes) are:
	LOS	"Loss of Signal" (input power) alarm (cerent15216EdfaAlarmLpin).
	GAIN	"Gain Out of Range" alarm (cerent15216EdfaAlarmGain).
	LPOUT	"Loss of Output Power" alarm (cerent15216EdfaAlarmLpout).
date	yyyy-mm-dd	Date of origination of TL1 message.
ntfncde		Notification code (maps to cerent15216EdfaAlarmPriority). Possible values are:
	MJ	Major alarm.
	MN	Minor alarm.
	NA	No alarm.
ocrdat	m-d	Date (month-day) of the event occurrence (derived from cerent15216EdfaDateAndTimeString).
ocrtm	h-m-s	Time (hour-minute-second) of the event occurrence (derived from cerent15216EdfaDateAndTimeString).
sid	string	Source identifier uniquely identifies the source of a TL1 autonomous command.
srveff		Effect on service. Possible values are:
	SA	Service affecting.
	NSA	Non-service affecting.
time	hh:mm:ss	Time of origination of TL1 message.

9.7.30 RTRV-COND-ENV

Command: RTRV-COND-ENV

Description: Generates a report on the condition (state) of environmental (power bus) alarms.

Syntax:

RTRV-COND-ENV:[<tid>]:<aid>:<ctag>::[<condtype>][,,];

   <sid> <date> <time>

M <ctag> COMPLD

   "<aid>,<ccm>:<ntfcncde>,<condtype>,<srveff>,<ocrdat>,<ocrtm>,,,<conddescr>"

;

Example 9-32 RTRV-COND-ENV Command and Response

Amp01:ONS15216 EDFA2> RTRV-COND-ENV:Amp01:ALL:229::PWRBUSA;

   Amp01 2002-06-20 14:30:00

M 229 COMPLD

   "PWR-A,ENV:MJ,PWRBUSA,NSA,6-20,14-25-30,,,\"Power Bus A Alarm\""

;




Table 9-37 RTRV-COND-ENV Syntax Description 

Parameter	Syntax	Description
aid		Specifying PWR-A or PWR-B in input has a filter effect on the response.
	PWR-A	Affecting Power Bus A (or both A and B).
	PWR-B	Affecting Power Bus B.
	ALL	Any or all of the preceding (command input only).
conddescr		Detailed text description of the event. The conddescr is 1 to 64 characters of ASCII text. See condtype below.
condtype		Condition type identifies the type of alarm (maps to cerent15216EdfaLogEventID). Possible condtype and corresponding conddescr (in quotes) are:
	PWRBUSA	"Power Bus A (voltage) Alarm" (cerent15216EdfaAlarmPowerBusA).
	PWRBUSB	"Power Bus B (voltage) Alarm" (cerent15216EdfaAlarmPowerBusB).
date	yyyy-mm-dd	Date of origination of TL1 message.
ntfncde		Notification code (maps to cerent15216EdfaAlarmPriority). Possible values are:
	MJ	Major alarm.
	MN	Minor alarm.
	NA	No alarm.
ocrdat	m-d	Date (month-day) of the event occurrence (derived from cerent15216EdfaDateAndTimeString).
ocrtm	h-m-s	Time (hour-minute-second) of the event occurrence (derived from cerent15216EdfaDateAndTimeString).
sid	string	Source identifier uniquely identifies the source of a TL1 autonomous command.
srveff		Effect on service. Possible values are:
	SA	Service affecting.
	NSA	Non-service affecting.
time	hh:mm:ss	Time of origination of TL1 message.

9.7.31 RTRV-COND-EQPT

Command: RTRV-COND-EQPT

Description: Generates a report on the condition (state) of general alarms.

Syntax:

RTRV-COND-EQPT:[<tid>]:<aid>:<ctag>::[<condtype>][,,];

   <sid> <date> <time>

M <ctag> COMPLD

   "<aid>:<ntfcncde>,<condtype>,<srveff>,<ocrdat>,<ocrtm>,,,<conddescr>"

;

Example 9-33 RTRV-COND-EQPT Command and Response

Amp01:ONS15216 EDFA2> RTRV-COND-EQPT:Amp01:ALL:229::LCRNT1;

   Amp01 2002-06-20 14:30:00

M 229 COMPLD

   "EQPT:MN,LCRNT1,NSA,6-20,14-25-30,,,\"Excessive Pump1 Current\""

;




Table 9-38 RTRV-COND-EQPT Syntax Description 

Parameter	Syntax	Description
aid		EQPT and ALL have same input effect.
	EQPT	General parameters of the ONS 15216 EDFA2 (not directly affecting optical signal or power bus).
	ALL	Any or all of the preceding (command input only).
conddescr		Detailed text description of the event. The conddescr is 1 to 64 characters of ASCII text. See condtype below.
condtype		Condition type identifies the type of alarm (maps to cerent15216EdfaLogEventID). Possible condtype and corresponding conddescr (in quotes) are:
	CTMP	"Case Temperature Out of Range" alarm (cerent15216EdfaAlarmCtmp).
	LCRNT1	"Excessive Pump1 Current" alarm (cerent15216EdfaAlarmLcrnt1).
	LCRNT2	"Excessive Pump2 Current" alarm (cerent15216EdfaAlarmLcrnt2).
	LTMP1	"Excessive Pump1 Temperature" alarm (cerent15216EdfaAlarmLtmp1).
	LTMP2	"Excessive Pump2 Temperature" alarm (cerent15216EdfaAlarmLtmp2).
date	yyyy-mm-dd	Date of origination of TL1 message.
ntfncde		Notification code (maps to cerent15216EdfaAlarmPriority). Possible values are:
	MJ	Major alarm.
	MN	Minor alarm.
	NA	No alarm.
ocrdat	m-d	Date (month-day) of the event occurrence (derived from cerent15216EdfaDateAndTimeString).
ocrtm	h-m-s	Time (hour-minute-second) of the event occurrence (derived from cerent15216EdfaDateAndTimeString).
sid	string	Source identifier uniquely identifies the source of a TL1 autonomous command.
srveff		Effect on service. Possible values are:
	SA	Service affecting.
	NSA	Non-service affecting.
time	hh:mm:ss	Time of origination of TL1 message.

9.7.32 RTRV-DFLT-SECU

Command: RTRV-DFLT-SECU

Description: Retrieves the timeout value(s) for user access level(s).

Syntax:

RTRV-DFLT-SECU:[<tid>]:<aid>:<ctag>;

   <sid> <date> <time>

M <ctag> COMPLD

   "<aid>:AL=<al>,TMOUT=<timeout>"

;

Example 9-34 RTRV-DFLT-SECU Command and Response

Amp01:ONS15216 EDFA2> RTRV-DFLT-SECU:Amp01:ALL:123;

   Amp01 2002-01-12 08:01:05

M 123 COMPLD

   "EQPT:AL=R,TMOUT=60"

   "EQPT:AL=RW,TMOUT=30"

   "EQPT:AL=RWA,TMOUT=15"

;




Table 9-39 RTRV-DFLT-SECU Syntax Description 

Parameter	Syntax	Description
date	yyyy-mm-dd	Date of origination of TL1 message.
time	hh:mm:ss	Time of origination of TL1 message.
aid		EQPT and ALL have same input effect.
	EQPT	General parameters of the ONS 15216 EDFA2 (not directly affecting optical signal or power bus).
	ALL	Any or all of the preceding (command input only).
al		Access level of the user. See "Summary of Security Permissions for TL1 Commands" section for access level permissions.
	R	Read only privileges.
	RW	Read and write privileges.
	RWA	Read, write, and administrative privileges.
timeout	integer	Timeout in minutes.

9.7.33 RTRV-DWDM

Command: RTRV-DWDM

Description: Retrieves the ONS 15216 EDFA2 optical control configuration.

Syntax:

RTRV-DWDM:[<tid>]:<aid>:<ctag>;

   <sid> <date> <time>

M <ctag> COMPLD

   "<aid>:INPWRMICROW=<inputpoweruw>,INPWRDBM=<inputpowerdbm>,OUTPWRMILLIW=<outputpowermw> ,OUTPWRDBM=<outputpowerdbm>,PUMP1CTRLMODE=<pump1ctrlmode>,PUMP1CTRLVALUE=<pump1ctrlvalue>, PUMP2CTRLMODE=<pump2ctrlmode>,PUMP2CTRLVALUE=<pump2ctrlvalue>,OVERALLGAINMEASURED=<gainmea sured>,PREATTMEASURED=<preattmeasured>"

;

Example 9-35 RTRV-DWDM Command and Response

Amp01:ONS15216 EDFA2> RTRV-DWDM:Amp01:ALL:123;

   Amp01 2002-06-20 14:30:00

M 124 COMPLD

   "1:INPWRMICROW=264,INPWRDBM=-1578,OUTPWRMILLIW=172,OUTPWRDBM=237,PUMP1CTRLMODE=GAINTEMP ,PUMP1CTRLVALUE=169,PUMP2CTRLMODE=GAINTEMP,PUMP2CTRLVALUE=169,OVERALLGAINMEASURED=169,PREA TTMEASURED=60"

;




Table 9-40 RTRV-DWDM Syntax Description 

Parameter	Syntax	Description
date	yyyy-mm-dd	Date of origination of TL1 message.
time	hh:mm:ss	Time of origination of TL1 message.
aid		1 and ALL have same input effect.
	1	Directly affecting the optical signal.
	ALL	Any or all of the preceding (command input only).
inputpoweruw	0 - 99999	Input power (signal) in units of 10 microW (cerent15216EdfaInPoweruW).
inputpowerdbm	-999999 - 999999	Input power (signal) in units of 100 dBm (cerent15216EdfaInPowerdBm).
outputpowermw	0 - 999999	Output power in units of 100 mW (cerent15216EdfaOutPowermW).
outputpowerdbm	-99999 - 99999	Output power in units of 100 dBm (cerent15216EdfaOutPowerdBm).
pump1ctrlmode, pump2ctrlmode		Pump 1 or pump 2 control mode (maps to cerent15216EdfaPumpCfgControlMode for the corresponding pump). Possible values are:
	CRNT	Constant Pump Current mode (cerent15216EdfaPumpCfgControlMode set to constCurrent).
	PWR	Constant Pump Power mode (cerent15216EdfaPumpCfgControlMode set to constPower).
	OPWR	Constant Output Power mode (cerent15216EdfaPumpCfgControlMode set to constOutputPower). A valid mode only for pump 2.
	GAINTEMP	Constant Gain Temperature Compensated mode (manufacturer default) (cerent15216EdfaPumpCfgControlMode set to constGainTempComp).
	IDLE	Pump is shut down (cerent15216EdfaPumpCfgControlMode set to idle).
pump1ctrlvalue, pump2ctrlvalue		Pump 1 or pump 2 control value. This value's interpretation depends on the control mode of the corresponding pump. Possible values are:
	0 - 300	Current value in mA when mode is CRNT (gets cerent15216EdfaPumpCfgConstPumpCurrent).
	0 - 100	Pump power in mW when mode is PWR (gets cerent15216EdfaPumpCfgConstPumpPower).
	0 - 650	Output power in units of 10 mW when mode is OPWR (gets cerent15216EdfaPumpCfgConstOutPower).
gainmeasured	0 - 230	Value of gain in units of 10 dB when mode is GAINTEMP (gets cerent15216EdfaConstGainOverallGainMeasured).
preattmeasured	0 - 110	Gain pre-attenuation value in units of 10 dB (gets cerent15216EdfaVariableGainPreAttenuationMeasured).

9.7.34 RTRV-ENV

Command: RTRV-ENV

Description: Retrieves the ONS 15216 EDFA2 environmental parameter configuration.

Syntax:

RTRV-ENV:[<tid>]:<aid>:<ctag>;

   <sid> <date> <time>

M <ctag> COMPLD

   "<aid>:PWRBUSMODE=<pwrbusmode>"

;

Example 9-36 RTRV-ENV Command and Response

Amp01:ONS15216 EDFA2> RTRV-ENV:Amp01:ALL:123;

   Amp01 2002-06-20 14:30:00

M 123 COMPLD

   "PWR-B:PWRBUSMODE=DUPLEX"

;




Table 9-41 RTRV-ENV Syntax Description 

Parameter	Syntax	Description
date	yyyy-mm-dd	Date of origination of TL1 message.
time	hh:mm:ss	Time of origination of TL1 message.
aid		PWR-A, PWR-B, and ALL have same input effect.
	PWR-A	Affecting Power Bus A (or both A and B).
	PWR-B	Affecting Power Bus B.
	ALL	Any or all of the preceding (command input only).
pwrbusmode		Power bus mode setting (cerent15216EdfaPowerBusMode). Possible values are:
	SIMPLEX	Simplex mode. Requires power only to bus A (cerent15216EdfaPowerBusMode set to simplex).
	DUPLEX	Duplex mode (manufacturer default). Requires power to both bus A and B. (cerent15216EdfaPowerBusMode set to duplex).

9.7.35 RTRV-HDR

Command: RTRV-HDR

Description: Retrieves header. Sends standard keep-alive message used to ping the ONS 15216 EDFA2. It also returns the current date, time, and sid/tid name of the ONS 15216 EDFA2 in the reply.

Syntax:

RTRV-HDR:[<tid>]::<ctag>;

   <sid> <date> <time>

M <ctag> COMPLD

;

Example 9-37 RTRV-HDR Command and Response

Amp01:ONS15216 EDFA2> RTRV-HDR:Amp01::100;

   Amp01 2001-06-08 08:10:50

M 100 COMPLD

;




Table 9-42 RTRV-HDR Syntax Description 

Parameter	Syntax	Description
date	yyyy-mm-dd	Date of origination of TL1 message.
time	hh:mm:ss	Time of origination of TL1 message.

9.7.36 RTRV-INV

Command: RTRV-INV

Description: Retrieves the inventory information of the ONS 15216 EDFA2.

Syntax:

RTRV-INV:[<tid>]:<aid>:<ctag>;

   <sid> <date> <time>

M <ctag> COMPLD

   "<aid>:CLEI=<cleicode>,DESCR=<descr>,NAME=<name>,HARDWAREREV=<hwrev>, FIRMWAREREV=<fwrev>,SOFTWAREREV=<swrev>,SERIALNUM=<serialnum>,MFGNAME=<mfg>,MODELNAME=<mod el>"

;

Example 9-38 RTRV-INV Command and Response

Amp01:ONS15216 EDFA2> RTRV-INV:Amp01:ALL:123;

   Amp01 2002-01-12 08:01:05

M 123 COMPLD

   "EQPT:CLEI=IPI01AA0AAA,DESCR=ONS15216EDFA2,NAME=Amp01,HARDWAREREV=v3.0.0, FIRMWAREREV=v1.3.1,SOFTWAREREV=v2.1.7,SERIALNUM=DIT0533000P,MFGNAME=Cisco Systems,MODELNAME=511112"

;




Table 9-43 RTRV-INV Syntax Description 

Parameter	Syntax	Description
date	yyyy-mm-dd	Date of origination of TL1 message.
time	hh:mm:ss	Time of origination of TL1 message.
aid		EQPT and ALL have same input effect.
	EQPT	General parameters of the ONS 15216 EDFA2 (not directly affecting optical signal or power bus).
	ALL	Any or all of the preceding (command input only).
cleicode	string	CLEI code (cerent15216EdfaCLEI).
descr	string	System description (cerent15216EdfaPhysicalDescr).
fwrev	string	Firmware revision number (cerent15216EdfaPhysicalFirmwareRev).
hwrev	string	Hardware revision number (cerent15216EdfaPhysicalHardwareRev).
mfg	string	Manufacturer name (cerent15216EdfaPhysicalMfgName).
model	string	Model name (cerent15216EdfaPhysicalModelName).
name	string	System's sid/tid name (does not map to an SNMP attribute).
serialnum	string	System serial number (cerent15216EdfaPhysicalSerialNum).
swrev	string	Software revision number (cerent15216EdfaPhysicalSoftwareRev).

9.7.37 RTRV-NE-GEN

Command: RTRV-NE-GEN

Description: Retrieves general parameters of the ONS 15216 EDFA2. Retrieves sid/tid name, IP address and mask, and default router information. Also retrieves the boot table content.

Syntax:

RTRV-NE-GEN:[<tid>]::<ctag>;

   <sid> <date> <time>

M <ctag> COMPLD

   "<aid>:NAME=<name>,IPADDR=<ipaddr>,IPMASK=<ipmask>,DEFRTR=<defrtr>, BOOTRECORDTYPE1=<bootrectype1>, BOOTFILENAME1=<bootfilename1>,BOOTIPADDR1=<bootipaddr1>, BOOTRECORDTYPE2=<bootrectype2>,BOOTFILENAME2=<bootfilename2>, BOOTIPADDR2=<bootipaddr2>,CLI=<cli>"

;

Example 9-39 RTRV-NE-GEN Command and Response

Amp01:ONS15216 EDFA2> RTRV-NE-GEN:Amp01::123;

   Amp01 2002-01-12 08:01:05

M 123 COMPLD

   "EQPT:NAME=Amp01,IPADDR=172.22.87.100,IPMASK=255.255.255.0,DEFRTR=172.22

.87.2,BOOTRECORDTYPE1=FLASH,BOOTFILENAME1=15216EdfaSw_2.1.0,BOOTIPADDR1=0.0.0.0,

BOOTRECORDTYPE2=TFTP,BOOTFILENAME2=bin/15216EdfaSw_2.0.1,BOOTIPADDR2=1

72.22.128.249,CLI=TL1"

;




Table 9-44 RTRV-NE-GEN Syntax Description 

Parameter	Syntax	Description
aid		Always EQPT.
	EQPT	General parameters of the ONS 15216 EDFA2 (not directly affecting optical signal or power bus).
name	string	System's sid/tid name.
ipaddr	string	IP address of the system (cerent15216EdfaSromIpMgmtEnetAddress).
ipmask	string	Subnet mask of the system (cerent15216EdfaSromIpMgmtEnetSubNetMask).
defrtr	string	IP address of the default router (cerent15216EdfaSromIpMgmtDefaultRouterAddress).
bootrectype1		Boot record type (cerent15216EdfaBootType for first entry). Possible values are:
	FLASH	Boot from flash.
	TFTP	Boot through TFTP.
bootfilename1	string	Boot file name (cerent15216EdfaBootFileName for first entry). File names are case sensitive.
bootipaddr1	string	IP address to boot from if bootrectype1 is set to TFTP (cerent15216EdfaBootIpAddress for first entry).
bootrectype2		Boot record type (cerent15216EdfaBootType for second entry). Possible values are:
	FLASH	Boot from flash.
	TFTP	Boot through TFTP.
bootfilename2	string	Boot file name (cerent15216EdfaBootFileName for second entry). File names are case sensitive.
bootipaddr2	string	IP address to boot from if bootrectype2 is set to TFTP (cerent15216EdfaBootIpAddress for second entry).
cli		Default type of command line interface for all EIA/TIA-232 and default telnet port user sessions with the ONS 15216 EDFA2. Possible values are:
	TL1	TL1shell interface (manufacturer default).
	ASH	ASH shell interface - ONS 15216 EDFA2's native interface.

9.7.38 RTRV-RFILE

Command: RTRV-RFILE

Description: Lists a specific file or all files on the flash file system of the ONS 15216 EDFA2.

Syntax:

RTRV-RFILE:[<tid>]::<ctag>::[<localfilename>+];

   <sid> <date> <time>

M <ctag> COMPLD

   "<aid>:<localfilename>"

;

Example 9-40 RTRV-RFILE Command and Response (List all Files)

Amp01:ONS15216 EDFA2> RTRV-RFILE:Amp01::123::;

   Amp01 2002-01-12 08:01:05

M 123 COMPLD

   "EQPT:snmp.cfg,15216EdfaSw_2.1.0,passwd"

;

Example 9-41 RTRV-RFILE Command and Response (List a Specific File)

Amp01:ONS15216 EDFA2> RTRV-RFILE:Amp01::123::snmp.cfg;

   Amp01 2002-01-12 08:01:05

M 123 COMPLD

   "EQPT:snmp.cfg"

;




Table 9-45 RTRV-RFILE Syntax Description 

Parameter	Syntax	Description
aid		Always EQPT.
	EQPT	General parameters of the ONS 15216 EDFA2 (not directly affecting optical signal or power bus).
localfilename	string	Name of the file on the flash file system of the ONS 15216 EDFA2 that is to be listed. A null value in the request means all files are to be listed. A null value in the response means the file specified does not exist. File names are case sensitive.

9.7.39 RTRV-TH-DWDM

Command: RTRV-TH-DWDM

Description: Retrieves optical threshold and set point values for the ONS 15216 EDFA2.

Syntax:

RTRV-TH->][,][,];

   <sid> <date> <time>

M <ctag> COMPLD

   "<aid>,DWDM:<thresholdtype>,,,<thresholdvalue>"

;

Example 9-42 RTRV-TH-DWDM Command and Response

Amp01:ONS15216 EDFA2> RTRV-TH-DWDM:Amp01:ALL:123::LPOUTDEV;

   Amp01 2001-06-08 09:00:05

M 123 COMPLD

   "1,DWDM:LPOUTDEV,,,1000"

;




Table 9-46 RTRV-TH-DWDM Syntax Description 

Parameter	Syntax	Description
date	yyyy-mm-dd	Date of origination of TL1 message.
time	hh:mm:ss	Time of origination of TL1 message.
aid		1 and ALL have same input effect.
	1	Directly affecting the optical signal.
	ALL	Any or all of the preceding (command input only).
threshholdtype and thresholdvalue pairs		Type of threshold or set point that is to be retrieved. A null value is equivalent to ALL. Possible to specify values for one or more of the following:
	LOSHYST	Loss of signal (input power) hysteresis (cerent15216EdfaLOSHysteresis). thresholdvalue can be between 0 and 1000, with default of 100, in units of 100 dBm.
	LOSTH	Loss of signal (input power) threshold (cerent15216EdfaLOSThreshold). thresholdvalue can be between -3100 and -1500, with default of -3000, in units of 100 dBm.
	LPOUTDEV	Loss of output power deviation (cerent15216EdfaLpoutDeviation). thresholdvalue can be between 0 and 1000, with default of 200, in units of 100 dBm.
	LPOUTHYST	Loss of output power hysteresis (cerent15216EdfaLpoutHysteresis). thresholdvalue can be between 0 and 1000, with default of 100, in units of 100 dBm.
	LPOUTSETPT	Loss of output power set point (cerent15216EdfaLpoutSetpoint). This read-only value is only valid when amplifier is in Constant Output Power (OPWR) and Constant Pump Power (PWR) modes. Can be disregarded when in Constant Gain Temperature Compensated (GAINTEMP) or Constant Pump Current (CRNT) mode. thresholdvalue is read-only and automatically determined by the pump control mode with a possible value between 0 and 1000 in units of 10 mW.

9.7.40 RTRV-TH-ENV

Command: RTRV-TH-ENV

Description: Retrieves threshold values of the environmental (power bus) parameters of the ONS 15216 EDFA2.

Syntax:

RTRV-TH-ENV:[<tid>]:<aid>:<ctag>::[<thresholdtype>][,];

   <sid> <date> <time>

M <ctag> COMPLD

   "<aid>,ENV:<thresholdtype>,,,<thresholdvalue>"

;

Example 9-43 RTRV-TH-ENV Command and Response

Amp01:ONS15216 EDFA2> RTRV-TH-ENV:Amp01:ALL:123::PWRBUSMIN;

   Amp01 2002-07-16 14:24:29

M 123 COMPLD

   "PWR-A,ENV:PWRBUSMIN,,,420"

;




Table 9-47 RTRV-TH-ENV Syntax Description 

Parameter	Syntax	Description
date	yyyy-mm-dd	Date of origination of TL1 message.
time	hh:mm:ss	Time of origination of TL1 message.
aid		PWR-A, PWR-B, and ALL have same input effect.
	PWR-A	Affecting Power Bus A (or both A and B).
	PWR-B	Affecting Power Bus B.
	ALL	Any or all of the preceding (command input only).
threshholdtype and thresholdvalue pairs		Type of threshold that is to be retrieved. A null value is equivalent to ALL. Possible to specify values for one or more of the following:
	PWRBUSMIN	Power bus minimum voltage (cerent15216EdfaPowerBusDCVoltageMin). thresholdvalue can be between 350 and 700, with default of 400, in units of -10 VDC.
	PWRBUSMAX	Power bus maximum voltage (cerent15216EdfaPowerBusDCVoltageMax). thresholdvalue can be between 350 and 700, with default of 570, in units of -10 VDC.

9.7.41 RTRV-TH-EQPT

Command: RTRV-TH-EQPT

Description: Retrieves general threshold values for the ONS 15216 EDFA2.

Syntax:

RTRV-TH-EQPT:[<tid>]:<aid>:<ctag>::[<thresholdtype>][,][,];

   <sid> <date> <time>

M <ctag> COMPLD

   "<aid>:<thresholdtype>,,,<thresholdvalue>"

;

Example 9-44 RTRV-TH-EQPT Command and Response

Amp01:ONS15216 EDFA2> RTRV-TH-EQPT:Amp01:ALL:123::MAXCTMP;

   Amp01 2001-06-08 09:00:05

M 123 COMPLD

   "EQPT:MAXCTMP,,,60"

;




Table 9-48 RTRV-TH-EQPT Syntax Description 

Parameter	Syntax	Description
date	yyyy-mm-dd	Date of origination of TL1 message.
time	hh:mm:ss	Time of origination of TL1 message.
aid		EQPT and ALL have same input effect.
	EQPT	General parameters of the ONS 15216 EDFA2 (not directly affecting optical signal or power bus).
	ALL	Any or all of the preceding (command input only).
threshholdtype and thresholdvalue pairs		Type of threshold or set point that is to be retrieved. A null value is equivalent to ALL. Possible to specify values for one or more of the following:
	MAXCTMP	Maximum case temperature (cerent15216EdfaCtmpMax). thresholdvalue can be between 20 and 70, with default of 65 in units of °C.
	MAXCTMPHYST	Maximum case temperature hysteresis (cerent15216EdfaCtmpMaxHysteresis). thresholdvalue can be between 0 and 10, with default of 1, in units of °C.
	MINCTMP	Minimum case temperature (cerent15216EdfaCtmpMin). thresholdvalue can be between -10 and 10, with default of -5, in units of °C.
	MINCTMPHYST	Minimum case temperature hysteresis (cerent15216EdfaCtmpMinHysteresis). thresholdvalue can be between 0 and 10, with default of 1, in units of °C.

9.7.42 RTRV-TOD

Command: RTRV-TOD

Description: Retrieves the date and time of the ONS 15216 EDFA2.

Syntax:

RTRV-TOD:[<tid>]::<ctag>[::];

   <sid> <date> <time>

M <ctag> COMPLD

   "<tmody>,<tmtype>,<tmsrcdv>,<tmsrcst>"

;

Example 9-45 RTRV-TOD Command and Response

Amp01:ONS15216 EDFA2> RTRV-TOD:Amp01::123;

   Amp01 2002-06-20 14:30:00

M 123 COMPLD

   "2002,06,20,14,30,00,000,UTC,GPS,IS-ACT"

;




Table 9-49 RTRV-TOD Syntax Description 

Parameter	Syntax	Description
date	yyyy-mm-dd	Date of origination of TL1 message.
time	hh:mm:ss	Time of origination of TL1 message.
tmody format: YYYY MM DD HH MM SS sss	01 - 12 01 - 31 00 - 23 00 - 59 00 - 59 000	Time of day of the format: YYYY,MM,DD,HH,MM,SS,sss Current calendar year Month Day Hour Minutes Seconds Sub-seconds, currently fixed at 000.
tmtype	UTC	Type of time, currently fixed at universal coordinated time (UTC), which is the same as Greenwich Mean Time (GMT).
tmsrcdv	GPS	Time source deviation, currently fixed at GPS.
tmsrcst	IS-ACT	State of the time source, of the format <primaryState>-<secondaryState> (per Telcordia GR-1093-CORE), currently fixed at IS-ACT (In_Service, Active).

9.7.43 RTRV-USER-SECU

Command: RTRV-USER-SECU

Description: Retrieves the access level of an existing user from the system. Does not return the password.

Syntax:

RTRV-USER-SECU:[<tid>]:<uid>:<ctag>;

   <sid> <date> <time>

M <ctag> COMPLD

   "<uid>,<al>"

;

Example 9-46 RTRV-USER-SECU Command and Response

Amp01:ONS15216 EDFA2> RTRV-USER-SECU:Amp01:jsmith:123;

   Amp01 2002-05-13 17:23:16

M 123 COMPLD

   "jsmith,RW"

;




Table 9-50 RTRV-USER-SECU Syntax Description 

Parameter	Syntax	Description
sid	string	Source identifier uniquely identifies the source of a TL1 autonomous command.
al		Access level of the user. See "Summary of Security Permissions for TL1 Commands" section for access level permissions.
	R	Read only privileges.
	RW	Read and write privileges.
	RWA	Read, write, and administrative privileges.
uid	string	User identifier (user name) of the existing user. If no user identifier is specified and the current user has RWA access level, it will list all existing users and their security levels.

9.7.44 SET-ATTR-SECUDFLT

Command: SET-ATTR-SECUDFLT

Description: Sets the timeout value of user sessions for users with a specific access level. If no communication occurs for this time, the user session is closed by the ONS 15216 EDFA2 TL1 agent. Users affected by changes to the timeout must log out and log in again for the change to take effect.

Syntax:

SET-ATTR-SECUDFLT:[<tid>]::<ctag>::AL=<al>,TMOUT=<timeout>[,][,][,][,][,];

Example 9-47 SET-ATTR-SECUDFLT Command

Amp01:ONS15216 EDFA2> SET-ATTR-SECUDFLT:Amp01::123::AL=RW,TMOUT=45;




Table 9-51 SET-ATTR-SECUDFLT Syntax Description 

Parameter	Syntax	Description
al		Access level for which the timeout is being set. See "Summary of Security Permissions for TL1 Commands" section for access level permissions.
	R	Read only privileges.
	RW	Read and write privileges.
	RWA	Read, write, and administrative privileges.
timeout	0 - 99	Value of the timeout in minutes for the corresponding access level. Defaults are: R = 60 min. RW = 30 min. RWA = 15 min. 0 means no timeout.

9.7.45 SET-TH-DWDM

Command: SET-TH-DWDM

Description: Sets optical threshold values for the ONS 15216 EDFA2.

Syntax:

SET-TH-DWDM:[<tid>]:<aid>:<ctag>::<thresholdtype>,<thresholdvalue>[,,];

Example 9-48 SET-TH-DWDM Command

Amp01:ONS15216 EDFA2> SET-TH-DWDM:Amp01:ALL:123::LOSTH,-1500;




Table 9-52 SET-TH-DWDM Syntax Description 

Parameter	Syntax	Description
aid		1 and ALL have same input effect.
	1	Directly affecting the optical signal.
	ALL	Any or all of the preceding (command input only).
threshholdtype and thresholdvalue pairs	string	Type of threshold that is to be set. The threshold is set to the thresholdvalue that follows the comma. Possible to specify values for one or more of the following:
	LOSHYST	Loss of signal (input power) hysteresis (cerent15216EdfaLOSHysteresis). thresholdvalue can be between 0 and 1000, with default of 100, in units of 100 dBm.
	LOSTH	Loss of signal (input power) threshold (cerent15216EdfaLOSThreshold). thresholdvalue can be between -3100 and -1500, with default of -3000, in units of 100 dBm.
	LPOUTDEV	Loss of output power deviation (cerent15216EdfaLpoutDeviation). thresholdvalue can be between 0 and 1000, with default of 200, in units of 100 dBm.
	LPOUTHYST	Loss of output power hysteresis (cerent15216EdfaLpoutHysteresis). thresholdvalue can be between 0 and 1000, with default of 100, in units of 100 dBm.

9.7.46 SET-TH-ENV

Command: SET-TH-ENV

Description: Sets threshold values of the environmental (power bus) parameters of the ONS 15216 EDFA2.

Syntax:

SET-TH-ENV:[<tid>]:<aid>:<ctag>::<thresholdtype>,<thresholdvalue>[,,];

Example 9-49 SET-TH-ENV Command

Amp01:ONS15216 EDFA2> SET-TH-ENV:Amp01:PWR-A:100::PWRBUSMIN,450;




Table 9-53 SET-TH-ENV Syntax Description 

Parameter	Syntax	Description
aid		PWR-A, PWR-B, and ALL have same input effect.
	PWR-A	Affecting Power Bus A (or both A and B).
	PWR-B	Affecting Power Bus B.
	ALL	Any or all of the preceding (command input only).
threshholdtype and thresholdvalue pairs		Type of threshold that is to be set. The threshold is set to the thresholdvalue that follows the comma. Possible to specify values for one or more of the following:
	PWRBUSMIN	Power bus minimum voltage (cerent15216EdfaPowerBusDCVoltageMin). thresholdvalue can be between 350 and 700, with default of 400, in units of -10 VDC.
	PWRBUSMAX	Power bus maximum voltage (cerent15216EdfaPowerBusDCVoltageMax). thresholdvalue can be between 350 and 700, with default of 570, in units of -10 VDC.

9.7.47 SET-TH-EQPT

Command: SET-TH-EQPT

Description: Sets general threshold values for the ONS 15216 EDFA2.

Syntax:

SET-TH-EQPT:[<tid>]:<aid>:<ctag>::<thresholdtype>,<thresholdvalue>[,,];

Example 9-50 SET-TH-EQPT Command

Amp01:ONS15216 EDFA2> SET-TH-EQPT:Amp01:ALL:123::MAXCTMP,60;




Table 9-54 SET-TH-EQPT Syntax Description 

Parameter	Syntax	Description
aid		EQPT and ALL have same input effect.
	EQPT	General parameters of the ONS 15216 EDFA2 (not directly affecting optical signal or power bus).
	ALL	Any or all of the preceding (command input only).
threshholdtype and thresholdvalue pairs	string	Type of threshold that is to be set. The threshold is set to the thresholdvalue that follows the comma. Possible to specify values for one or more of the following:
	MAXCTMP	Maximum case temperature (cerent15216EdfaCtmpMax). thresholdvalue can be between 20 and 70, with default of 65 in units of °C.
	MAXCTMPHYST	Maximum case temperature hysteresis (cerent15216EdfaCtmpMaxHysteresis). thresholdvalue can be between 0 and 10, with default of 1, in units of °C.
	MINCTMP	Minimum case temperature (cerent15216EdfaCtmpMin). thresholdvalue can be between -10 and 10, with default of -5, in units of °C.
	MINCTMPHYST	Minimum case temperature hysteresis (cerent15216EdfaCtmpMinHysteresis). thresholdvalue can be between 0 and 10, with default of 1, in units of °C.

9.7.48 STA-LOCL-RST

Command: STA-LOCL-RST

Description: Instructs the ONS 15216 EDFA2 to restore all the manufacturing default settings. The files on the flash file system (FFS), the date and time, the sid/tid name (name), and the values of manufacturing calibration are not affected. This command must be followed by the INIT-SYS command to take effect.

---

Warning This command resets the IP address, deletes the user directory, reverts CISCO15 to the default password, and resets other parameters to restore the unit to its state as shipped from manufacturing.

---

Syntax:

STA-LOCL-RST:[<tid>]::<ctag>;

Example 9-51 STA-LOCL-RST Command

Amp01:ONS15216 EDFA2> STA-LOCL-RST:Amp01::10;