Configuring Trunk and Uplink Card Interfaces

Table Of Contents

Configuring Trunk and Uplink Card Interfaces

Configuring 2.5-Gbps ITU Trunk Card Interfaces

Displaying the 2.5-Gbps ITU Trunk Card Interface Configuration

Configuring 10-Gbps ITU Trunk Card Interfaces

Displaying the 10-Gbps ITU Trunk Card Interface Configuration

Configuring 10-Gbps Uplink Card Interfaces

Displaying the 10-Gbps Uplink Card Interface Configuration

About Cross Connections

Configuring Cross Connections

Displaying the Cross Connection Configuration

About Alarm Thresholds

Configuring Alarm Thresholds

Displaying the Alarm Threshold Configuration

About Patch Connections

Configuring Patch Connections

Configuring Trunk and Uplink Card Interfaces

This chapter describes how to configure 2.5-Gbps ITU trunk cards, 10-Gbps ITU trunk cards, and 10-Gbps uplink cards on the Cisco ONS 15530. This chapter includes the following sections:

• Configuring 2.5-Gbps ITU Trunk Card Interfaces

• Configuring 10-Gbps ITU Trunk Card Interfaces

• Configuring 10-Gbps Uplink Card Interfaces

• About Cross Connections

• Configuring Cross Connections

• About Alarm Thresholds

• Configuring Alarm Thresholds

• About Patch Connections

• Configuring Patch Connections

Note To ensure the installed Cisco IOS software supports your hardware and provides the software features you wish to use, see the "New and Changed Information" section on page xiii. Also refer to the "Hardware Supported" section and "Feature Set" section of the latest release notes for the Cisco ONS 15530.

Configuring 2.5-Gbps ITU Trunk Card Interfaces

To configure the 2.5-Gbps ITU trunk card interface, perform the following tasks, beginning in global configuration mode:

Command

Purpose

Step 1

Switch(config)# interface waveethernetphy slot/0

Switch(config-if)#

Selects the interface to configure and enters interface configuration mode.

Step 2

Switch(config-if)# laser frequency number

Selects one of the two frequencies in GHz supported by the laser. The default is the lower frequency for the 2.5-Gbps ITU trunk card. (Optional)

Step 3

Switch(config-if)# [no] loopback [facility | terminal]

Enables or disables internal loopback for testing and defect isolation. (Optional)

Step 4

Switch(config-if)# [no] laser control safety enable

Enables or disables laser safety control.

Step 5

Switch(config-if)# [no] laser shutdown

Turns the laser on and off. (Optional)

Note The laser must warm up for 2 minutes before carrying traffic.

Step 6

Switch(config-if)# [no] cdl defect-indication force hop-endpoint

Enables or disables hop endpoint for in-band message channel defect indications when APS is not configured (Optional).

Step 7

Switch(config-if)# no shutdown

Enables the interface.

Step 8

Switch(config-if)# exit

Switch(config)

Returns to global configuration mode.

Step 9

Switch(config)# interface wavepatch slot/0/0

Switch(config-if)#

Selects the interface to configure and enters interface configuration mode.

Step 10

Switch(config-if)# optical threshold power receive {low | high} {alarm | warning} value [severity {critical | major | minor | not alarmed | not reported}]

Specifies the optical power receive threshold value in units of 0.1 dBm. The default values are as follows:

Low alarm: -28 dBm

Low warning: -26 dBm

High warning: -10 dBm

High alarm: -8 dBm

Alarm severity: major

Warning severity: not alarmed

Step 11

Switch(config-if)# [no] shutdown

Enables or disables the interface.

Repeat Step 9and Step 11 on wavepatch slot/0/1 for splitter 2.5-Gbps ITU trunk cards.

Caution Loopbacks on waveethernetphy interfaces disrupt service. Use this feature with care.

Note For configuration information for the ethernetdcc interface, see the "Configuring IP on Ethernetdcc Interfaces for the In-Band Message Channel" section on page 12-12.

Example

The following example shows how to configure 2.5-Gbps ITU trunk card waveethernetphy interfaces:
Switch(config)# interface waveethernetphy 10/0Switch(config-if)# cdl defect-indication force hop-endpointSwitch(config-if)# no shutdown
Displaying the 2.5-Gbps ITU Trunk Card Interface Configuration

To display the configuration of 2.5-Gbps ITU trunk card interfaces, use the following EXEC command:

Command

Purpose

show interfaces {waveethernetphy slot/0 | wavepatch slot/0/port}

Displays the interface configuration.

Examples

The following example shows how to display the configuration of a waveethernetphy interface:
Switch# show interfaces waveethernetphy 1/0WaveEthernetPhy1/0 is up, line protocol is upChannel: 1 Frequency: 192.1 Thz Wavelength: 1560.61 nmActive Wavepatch : Wavepatch1/0/0Splitter Protected : NoSignal quality : GoodReceive power level : -6.45 dBmLaser shut down : NoOsc physical port : NoWavelength used for inband management: NoLoopback not set
Configured threshold Group: NoneCDL HEC error count: 0CRC error count: 0Code violation and running disparity error count( 64b66b cvrd): 0
Defect Indication Status : upConfigured Node Behavior : Hop TerminatingCurrent Node Behavior : Hop TerminatingDefect Indication Receive : FDI-H FDI-EDefect Indication Transmit : BDI-H
Tx Frames sent to N/W : 218707020912
Tx Frames rcvd from Client : 0Tx CRC Errors : 0Tx HEC Errors : 0Tx QuadPHY sybl Errs : 4257380395Tx Dropped Frames : 0Tx Oversize Frames : 0Tx Undersize Frames : 0Tx Idle Frames from Fabric : 0Tx Generated CDL Idle Frames : 218720041509(having an SII of 255)
Rx Frames rcvd from N/W : 218719304600
Rx Frames sent to Client : 647Rx CRC Errors : 0Rx HEC Errors : 0Rx MII (Decoder) Errors : 0Rx Dropped Frames : 0Rx Oversize Frames : 0Rx Undersize Frames : 0Rx Total Drpd Idle Frames : 218719303953Rx Dropped CDL Idle Frames : 218719301229(having an SII of 255)
Last clearing of "show interface" counters neverHardware is data_enabled_portSwitch#sh int wavepatch 1/0/0Wavepatch1/0/0 is up, line protocol is upReceiver power level: -6.46 dBm
Optical threshold monitored for : Receive Power (in dBm)Threshold exceeded for : High Warning and High AlarmLow alarm value = -28.0 (default)Low Alarm Severity = majorLow warning value = -26.0 (default)Low Warning Severity = not alarmedHigh alarm value = -8.0 (default)High Alarm Severity = majorHigh warning value = -10.0 (default)High Warning Severity = not alarmedHardware is passive_port

The following example shows how to display the configuration of a wavepatch interface:
Switch# show interfaces wavepatch 1/0/0Wavepatch1/0/0 is up, line protocol is upReceiver power level: -6.46 dBm
Optical threshold monitored for : Receive Power (in dBm)Threshold exceeded for : High Warning and High AlarmLow alarm value = -28.0 (default)Low Alarm Severity = majorLow warning value = -26.0 (default)Low Warning Severity = not alarmedHigh alarm value = -8.0 (default)High Alarm Severity = majorHigh warning value = -10.0 (default)High Warning Severity = not alarmedHardware is passive_port
Configuring 10-Gbps ITU Trunk Card Interfaces

To configure the 10-Gbps ITU trunk card interface, perform the following tasks, beginning in global configuration mode:

Command

Purpose

Step 1

Switch(config)# interface waveethernetphy slot/0

Switch(config-if)#

Selects the interface to configure and enters interface configuration mode.

Step 2

Switch(config-if)# [no] loopback [facility | terminal]

Enables or disables internal loopback for testing and defect isolation. (Optional)

Step 3

Switch(config-if)# [no] laser shutdown

Turns the laser on and off. (Optional)

Note The laser must warm up for 2 minutes before carrying traffic.

Step 4

Switch(config-if)# [no] cdl defect-indication force hop-endpoint

Enables or disables hop endpoint for in-band message channel defect indications when APS is not configured. (Optional)

Step 5

Switch(config-if)# no shutdown

Enables the interface.

Step 6

Switch(config-if)# exit

Switch(config)

Returns to global configuration mode.

Step 7

Switch(config)# interface wavepatch slot/0/0

Switch(config-if)#

Selects the interface to configure and enters interface configuration mode.

Step 8

Switch(config-if)# optical threshold power receive {low | high} {alarm | warning} value [severity {critical | major | minor | not alarmed | not reported}]

Specifies the optical power receive threshold value in units of 0.1 dBm. The default values are as follows:

Low alarm: -22 dBm

Low warning: -20 dBm

High warning: -10 dBm

High alarm: -8 dBm

Alarm severity: major

Warning severity: not alarmed

Step 9

Switch(config-if)# [no] shutdown

Enables or disables the interface.

Repeat Step 7 and Step 9 on wavepatch slot/0/1 for splitter 10-Gbps ITU trunk cards.

Caution Loopbacks on waveethernetphy interfaces disrupt service. Use this feature with care.

Note For configuration information for the ethernetdcc interface, see the "Configuring IP on Ethernetdcc Interfaces for the In-Band Message Channel" section on page 12-12.

Example

The following example shows how to configure 10-Gbps ITU trunk card waveethernetphy interfaces:
Switch(config)# interface waveethernetphy 10/0Switch(config-if)# cdl defect-indication force hop-endpointSwitch(config-if)# no shutdown
Displaying the 10-Gbps ITU Trunk Card Interface Configuration

To display the configuration of 10-Gbps ITU trunk card interfaces, use the following EXEC command:

Command

Purpose

show interfaces {waveethernetphy slot/0[.subinterface] | wavepatch slot/0/port}

Displays the interface configuration.

Examples

The following example shows how to display the configuration of a waveethernetphy interface:
Switch# show interfaces waveethernetphy 10/0WaveEthernetPhy10/0 is down, line protocol is downChannel:30 Frequency:195.7 Thz Wavelength:1531.90 nmActive Wavepatch :Wavepatch10/0/1Splitter Protected :NoSignal quality :Loss of lockReceive power level :-35.0 dBmLaser Bias Current :91 mALaser Temperature :31.0 degree CLaser shut down :NoOsc physical port :NoWavelength used for inband management:NoLoopback not set
Configured threshold Group:NoneCDL HEC error count:0Number of times SF threshold exceeded:0Number of times SD threshold exceeded:0CRC error count:0Number of times SF threshold exceeded:0Number of times SD threshold exceeded:0Code violation and running disparity error count( 64b66b cvrd):0Number of times SF threshold exceeded:0Number of times SD threshold exceeded:0
Defect Indication Status :upConfigured Node Behavior :NoneCurrent Node Behavior :Path TerminatingDefect Indication Receive : NoneDefect Indication Transmit :BDI-H
Total Tx Frames Sent to N/W: 0Tx Gen CDL Idle Frame: 1843017892
Rx Frames rcvd from N/W: 0Rx CRC Errors: 0Rx HEC Errors: 0Rx XGMII Errors: 0Rx IPG drpd pkts: 0Rx Idle Packets : 0Rx Oversize Frames : 0Rx Undersize Frames : 0
Rx SII mismatch drpd data Frames : 0Rx SII mismatch drpd idle Frames : 0
Last clearing of "show interface" counters neverHardware is data_enabled_port

The following example shows how to display the configuration of a waveethernetphy subinterface:
Switch# show interfaces waveethernetphy 10/0.1WaveEthernetPhy10/0.1 is down, line protocol is down
Tx Frames Sent to N/W: 0Tx HEC Errors: 0Tx CRC Errors: 0Tx QuadPHY sybl Errs: 55688870321Tx Dropped Frames: 0Tx Oversize Frames: 0Tx Undersize Frames: 0Tx Rcvd Idle Packets: 0
Rx Frames Sent to Clnt: 0Rx FIFO full drpd pkts: 0Rx Gen Idle pkt cnt: 0
Last clearing of "show interface" counters neverHardware is data_enabled_port

The following example shows how to display the configuration of a wavepatch interface:
Switch# show interfaces wavepatch 3/0/0Wavepatch3/0/0 is up, line protocol is upReceiver power level:-9.86 dBmOptical threshold monitored for :Receive Power (in dBm)Threshold exceeded for :High WarningLow alarm value = -22.0 (default)Low Alarm Severity = majorLow warning value = -20.0 (default)Low Warning Severity = not alarmedHigh alarm value = -8.0 (default)High Alarm Severity = majorHigh warning value = -10.0 (default)High Warning Severity = not alarmedHardware is passive_port

Configuring 10-Gbps Uplink Card Interfaces

To configure the 10-Gbps uplink card interface, perform the following tasks, beginning in global configuration mode:

Command

Purpose

Step 1

Switch(config)# interface tengigethernetphy slot/0

Switch(config-if)#

Selects the interface to configure and enters interface configuration mode.

Step 2

Switch(config-if)# [no] loopback [facility | terminal]

Enables or disables internal loopback for testing and defect isolation. (Optional)

Step 3

Switch(config-if)# [no] laser shutdown

Turns the laser on and off. (Optional)

Step 4

Switch(config-if)# [no] cdl defect-indication force hop-endpoint

Enables or disables hop endpoint for in-band message channel defect indications when APS is not configured. (Optional)

Step 5

Switch(config-if)# [no] shutdown

Enables or disables the interface.

Caution Loopbacks on tengigethernetphy interfaces disrupt service. Use this feature with care.

Note For configuration information for the ethernetdcc interface, see the "Configuring IP on Ethernetdcc Interfaces for the In-Band Message Channel" section on page 12-12.

Example

The following example shows how to configure 10-Gbps uplink card interfaces:
Switch(config)# interface tengigethernetphy 10/0Switch(config-if)# cdl defect-indication force hop-endpointSwitch(config-if)# no shutdown
Displaying the 10-Gbps Uplink Card Interface Configuration

To display the configuration of 10-Gbps uplink card interfaces, use the following EXEC command:

Command

Purpose

show interfaces tengigethernetphy slot/0[.subinterface]

Displays the interface configuration.

Example

The following example shows how to display the configuration of an tengigethernetphy interface:
Switch# show interfaces tengigethernetphy 3/0TenGigEthernetPhy3/0 is up, line protocol is upSignal quality :Goodlaser shut down :OffOsc physical port :NoLoopback not setWavelength used for inband management:No
Configured threshold Group:NoneCDL HEC error count:0Number of times SF threshold exceeded:0Number of times SD threshold exceeded:0CRC error count:0Number of times SF threshold exceeded:0Number of times SD threshold exceeded:0Code violation and running disparity error count( 64b66b cvrd):0Number of times SF threshold exceeded:0Number of times SD threshold exceeded:0
Defect Indication Status :upConfigured Node Behavior :NoneCurrent Node Behavior :Path TerminatingDefect Indication Receive : NoneDefect Indication Transmit : None
Total Tx Frames Sent to N/W: 48297Tx Gen CDL Idle Frame: 2173636535
Rx Frames rcvd from N/W: 0Rx CRC Errors: 0Rx HEC Errors: 0Rx XGMII Errors: 0Rx IPG drpd pkts: 0Rx Idle Packets : 1836560218Rx Oversize Frames : 0Rx Undersize Frames : 0
Rx SII mismatch drpd data Frames : 0Rx SII mismatch drpd idle Frames : 1842816773
Last clearing of "show interface" counters neverHardware is data_enabled_port

The following example shows how to display the configuration of a tengigethernetphy subinterface:
Switch# show interfaces tengigethernetphy 3/0.4TenGigEthernetPhy3/0.4 is up, line protocol is up
Tx Frames Sent to N/W: 0Tx HEC Errors: 0Tx CRC Errors: 0Tx QuadPHY sybl Errs: 37831687439Tx Dropped Frames: 0Tx Oversize Frames: 0Tx Undersize Frames: 0Tx Rcvd Idle Packets: 0
Rx Frames Sent to Clnt: 0Rx FIFO full drpd pkts: 0Rx Gen Idle pkt cnt: 0
Last clearing of "show interface" counters neverHardware is data_enabled_port
About Cross Connections

The client signal follows a path of interface optical cross connections through the Cisco ONS 15530. Figure 7-1 shows an example of cross connections. Knowing the path of a signal through the shelf helps with system management and troubleshooting.

Figure 7-1 Optical Cross Connection Example

Configuring Cross Connections

The aggregated signal from the ESCON aggregation cards and the 8-port FC/GE aggregation cards passes through the switch fabric to the 2.5-Gbps ITU trunk card, 10-Gbps ITU trunk card, or the 10-Gbps uplink card. To establish a cross connection through the switch fabric, perform the following steps, beginning in global configuration mode:

Command

Purpose

Step 1

Switch(config)# connect interface1 interface2

Creates a cross connection between two interfaces through the switch fabric.

Example

The following example shows how to configure a cross connection between an ESCON aggregation card and a 2.5-Gbps ITU trunk card:
Switch(config)# connect portgroup 2/0/0 waveethernetphy 3/0

The following example shows how to configure a cross connection between an ESCON aggregation card and a 10-Gbps ITU trunk card:
Switch(config)# connect portgroup 2/0/0 waveethernetphy 3/0.1

The following example shows how to configure a cross connection between an ESCON aggregation card and a 10-Gbps uplink card:
Switch(config)# connect portgroup 2/0/0 tengigethernetphy 3/0.1
Displaying the Cross Connection Configuration

To display the cross connection configuration, use the following privileged EXEC command:

Command

Purpose

show connect [edge | intermediate [sort-channel | interface interface]]

Displays the signal cross connection configuration through the system.

Examples

The following example shows the cross connections within a system for an ESCON signal:
Switch# show connectIndex Client Intf Trunk Intf Kind C2TStatus T2CliStatus----- --------------- --------------- ----------- ---------- ---------15 Port3/0/0 WaveE8/0.1 Provisioned Up Up

The following example shows the cross connections within a system for a transponder signal:
Switch# show connect intermediateclient/ wave wave wdmwave client patch filter trk channel------------ ------------ ------- ------ ----- -------Trans7/0/0 Wave7/0 7/0/0* 0/0/0 0/0 257/0/1
About Alarm Thresholds

You can configure thresholds on the 2.5-Gbps ITU trunk card, 10-Gbps ITU trunk card, and 10-Gbps uplink interfaces that issue alarm messages to the system if the thresholds are exceeded.

Every second, the monitoring facility updates the counters that correspond to the alarm thresholds. When the signal degrades, or fails entirely, the system issues alarms to the console. These alarms can help isolate failures in the system and in the network.

You can configure more than one threshold list on an interface. The threshold lists cannot have overlapping counters so that only one counter is set for the interface. Also, the threshold list name cannot begin with the text string "default" because the it is reserved for use by the system.

Configuring Alarm Thresholds

To configure alarm thresholds on the 2.5-Gbps ITU trunk card, 10-Gbps ITU trunk card, and 10-Gbps uplink card interfaces, perform the following steps, beginning in global configuration mode:

Command

Purpose

Step 1

Switch(config)# threshold-list name

Switch(config-t-list)#

Creates or selects the threshold list to configure and enters threshold list configuration mode.

Note You cannot modify an existing threshold list if it is associated with an interface.

Step 2

Switch(config-t-list)# notification-throttle timer seconds

Configures the SNMP notification timer. The default value is 5 seconds. (Optional)

Step 3

Switch(config-t-list)# threshold name {cvrd | cdl hec | crc | sonet-sdh section cv | tx-crc} {failure | degrade} [index value]

Switch(config-threshold)#

Specifies a threshold type to modify and enters threshold configuration mode.

Step 4

Switch(config-threshold)# value rate value

Specifies the threshold rate value. This value is the negative power of 10 (10^-n).

Step 5

Switch(config-threshold)# description text

Specifies a description of the threshold. The default value is the null string. (Optional)

Step 6

Switch(config-threshold)# exit

Switch(config-t-list)#

Returns to threshold list configuration mode.

Repeat Step 3 through Step 6 to configure more thresholds in the threshold list.

Step 7

Switch(config-t-list)# exit

Switch(config)#

Returns to global configuration mode.

Step 8

Switch(config)# interface interface

Switch(config-if)#

Selects the interface to configure and enters interface configuration mode.

Step 9

Switch(config-if)# threshold-group name

Configures the threshold list on the interface.

Table 7-1 lists the threshold error rates in errors per second.

Table 7-1 Threshold Values for Monitored Rates in Errors Per Second

Rate

10-Gbps CVRD

10-Gbps CDL HEC

2.5-Gbps CVRD

2.5-Gbps CDL HEC

3

12,443,900

457901

19,968,416

1628

4

1,249,438

46765

2,055,776

166

5

124,944

4686

206,176

17

6

10,312

468

20,624

17

7

1031

47

2,064

17

8

103

4.7

208

17

9

10

0.47

24

17

Example

The following example shows how to create an alarm threshold list and configure that list for 10-Gbps ITU trunk card interfaces:
Switch# configure terminalSwitch(config)# threshold-list cvrd-countersSwitch(config-t-list)# threshold name cvrd degradeSwitch(config-threshold)# value rate 9Switch(config-threshold)# exitSwitch(config-t-list)# threshold name cvrd failureSwitch(config-threshold)# value rate 7Switch(config-threshold)# exitSwitch(config-t-list)# exitSwitch(config)# interface waveethernetphy 10/0Switch(config-if)# threshold-group cvrd-counters
Displaying the Alarm Threshold Configuration

To display the configuration of a threshold list and the threshold group for an interface, use the following EXEC commands:

Command

Purpose

show threshold-list [name]

Displays the threshold group configuration.

show interfaces {waveethernetphy slot/subcard | tengigethernetphy slot/subcard}

Displays the interface configuration.

Examples

The following example shows how to display the configuration of a threshold group:
Switch# show threshold-list cvrd-counters
Threshold List Name: cvrd-countersNotification throttle timer : 5 (in secs)Threshold name : CVRD Severity : DegradeValue : 10e-9APS Trigger : Not setThreshold name : CVRD Severity : FailureValue : 10e-7APS Trigger : Not set

The following example shows how to display the threshold group information for an interface:
Switch# show interfaces waveethernetphy 10/0WaveEthernetPhy10/0 is administratively down, line protocol is downChannel: 3 Frequency: 192.3 Thz Wavelength: 1558.98 nmActive Wavepatch : Wavepatch10/0/0Splitter Protected : NoReceive power level : -8.38 dBmLaser shut down : NoOsc physical port : NoWavelength used for inband management: NoLoopback not set
Configured threshold Group(s): cvrd-countersThreshold monitored for: 64b66b cvrdSF set value: 10e-7 (1031 in 1 secs)SD set value: 10e-9 (10 in 1 secs)CDL HEC error count: 0CRC error count: 0Code violation and running disparity error count( 64b66b cvrd): 0Number of times SF threshold exceeded: 0Number of times SD threshold exceeded: 0
Defect Indication Status : downConfigured Node Behavior : NoneCurrent Node Behavior : Path TerminatingDefect Indication Receive : FDI-H FDI-EDefect Indication Transmit : FDI-H FDI-E
MTU Size: 10232 bytes
Total Tx Frames Sent to N/W: 0Tx Gen CDL Idle Frame: 540367537118
Rx Frames rcvd from N/W: 0Rx IPG drpd pkts: 0Rx Idle Packets : 0Rx Oversize Frames : 0Rx Undersize Frames : 0
Rx SII mismatch drpd data Frames : 0Rx SII mismatch drpd idle Frames : 0
Last clearing of "show interface" counters neverHardware is data_enabled_port
About Patch Connections

Because the mux/demux modules are passive devices, the Cisco ONS 15530 does not detect its optical patch connection configuration. For system management purposes, you must also configure the patch connection configuration using the CLI.

Configuring Patch Connections

To configure patch connections between link cards within the same shelf, use the following global configuration commands:

Command

Purpose

patch wavepatch slot1/subcard1/port1 filter slot2/subcard2/port2

or

patch filter slot1/subcard1/port1 wavepatch slot2/subcard2/port2

Configures the patch connection between a 2.5-Gbps ITU trunk card or 10-Gbps ITU trunk card and an OADM module.

patch thru slot/subcard1 thru slot/subcard2

Configures the patch connection between two OADM modules.

patch wave slot/subcard oscfilter slot/subcard

or

patch oscfilter slot/subcard wave slot/subcard

Configures the patch connection between the wave interface on the OSC module and the oscfilter interface on the OADM module. This is only required if an OSC module is present.

Note If you correctly patch your cards, patch command configuration is not necessary for the signal to pass from the client to the trunk fiber.

Example

The following example shows how to configure the patch connections between line cards in a shelf with two OSC cards in slot 4, two OADM modules with OSC in slot 0, and a splitter 2.5-Gbps ITU trunk card or 10-Gbps ITU trunk card in slot 3:
Switch# configure terminalSwitch(config)# patch thru 0/0 thru 0/1Switch(config)# patch wave 4/0 oscfilter 0/0Switch(config)# patch wave 4/1 oscfilter 0/1Switch(config)# patch wavepatch 3/0/0 filter 0/0/1Switch(config)# patch wavepatch 3/0/1 filter 0/1/1

	Command	Purpose
Step 1	Switch(config)# interface waveethernetphy slot/0 Switch(config-if)#	Selects the interface to configure and enters interface configuration mode.
Step 2	Switch(config-if)# laser frequency number	Selects one of the two frequencies in GHz supported by the laser. The default is the lower frequency for the 2.5-Gbps ITU trunk card. (Optional)
Step 3	Switch(config-if)# [no] loopback [facility \| terminal]	Enables or disables internal loopback for testing and defect isolation. (Optional)
Step 4	Switch(config-if)# [no] laser control safety enable	Enables or disables laser safety control.
Step 5	Switch(config-if)# [no] laser shutdown	Turns the laser on and off. (Optional) Note The laser must warm up for 2 minutes before carrying traffic.
Step 6	Switch(config-if)# [no] cdl defect-indication force hop-endpoint	Enables or disables hop endpoint for in-band message channel defect indications when APS is not configured (Optional).
Step 7	Switch(config-if)# no shutdown	Enables the interface.
Step 8	Switch(config-if)# exit Switch(config)	Returns to global configuration mode.
Step 9	Switch(config)# interface wavepatch slot/0/0 Switch(config-if)#	Selects the interface to configure and enters interface configuration mode.
Step 10	Switch(config-if)# optical threshold power receive {low \| high} {alarm \| warning} value [severity {critical \| major \| minor \| not alarmed \| not reported}]	Specifies the optical power receive threshold value in units of 0.1 dBm. The default values are as follows: Low alarm: -28 dBm Low warning: -26 dBm High warning: -10 dBm High alarm: -8 dBm Alarm severity: major Warning severity: not alarmed
Step 11	Switch(config-if)# [no] shutdown	Enables or disables the interface. Repeat Step 9and Step 11 on wavepatch slot/0/1 for splitter 2.5-Gbps ITU trunk cards.

	Command	Purpose
Step 1	Switch(config)# interface tengigethernetphy slot/0 Switch(config-if)#	Selects the interface to configure and enters interface configuration mode.
Step 2	Switch(config-if)# [no] loopback [facility \| terminal]	Enables or disables internal loopback for testing and defect isolation. (Optional)
Step 3	Switch(config-if)# [no] laser shutdown	Turns the laser on and off. (Optional)
Step 4	Switch(config-if)# [no] cdl defect-indication force hop-endpoint	Enables or disables hop endpoint for in-band message channel defect indications when APS is not configured. (Optional)
Step 5	Switch(config-if)# [no] shutdown	Enables or disables the interface.

	Command	Purpose
Step 1	Switch(config)# threshold-list name Switch(config-t-list)#	Creates or selects the threshold list to configure and enters threshold list configuration mode. Note You cannot modify an existing threshold list if it is associated with an interface.
Step 2	Switch(config-t-list)# notification-throttle timer seconds	Configures the SNMP notification timer. The default value is 5 seconds. (Optional)
Step 3	Switch(config-t-list)# threshold name {cvrd \| cdl hec \| crc \| sonet-sdh section cv \| tx-crc} {failure \| degrade} [index value] Switch(config-threshold)#	Specifies a threshold type to modify and enters threshold configuration mode.
Step 4	Switch(config-threshold)# value rate value	Specifies the threshold rate value. This value is the negative power of 10 (10^-n).
Step 5	Switch(config-threshold)# description text	Specifies a description of the threshold. The default value is the null string. (Optional)
Step 6	Switch(config-threshold)# exit Switch(config-t-list)#	Returns to threshold list configuration mode. Repeat Step 3 through Step 6 to configure more thresholds in the threshold list.
Step 7	Switch(config-t-list)# exit Switch(config)#	Returns to global configuration mode.
Step 8	Switch(config)# interface interface Switch(config-if)#	Selects the interface to configure and enters interface configuration mode.
Step 9	Switch(config-if)# threshold-group name	Configures the threshold list on the interface.

Rate	10-Gbps CVRD	10-Gbps CDL HEC	2.5-Gbps CVRD	2.5-Gbps CDL HEC
3	12,443,900	457901	19,968,416	1628
4	1,249,438	46765	2,055,776	166
5	124,944	4686	206,176	17
6	10,312	468	20,624	17
7	1031	47	2,064	17
8	103	4.7	208	17
9	10	0.47	24	17

Command	Purpose
show threshold-list [name]	Displays the threshold group configuration.
show interfaces {waveethernetphy slot/subcard \| tengigethernetphy slot/subcard}	Displays the interface configuration.

Command	Purpose
patch wavepatch slot1/subcard1/port1 filter slot2/subcard2/port2 or patch filter slot1/subcard1/port1 wavepatch slot2/subcard2/port2	Configures the patch connection between a 2.5-Gbps ITU trunk card or 10-Gbps ITU trunk card and an OADM module.
patch thru slot/subcard1 thru slot/subcard2	Configures the patch connection between two OADM modules.
patch wave slot/subcard oscfilter slot/subcard or patch oscfilter slot/subcard wave slot/subcard	Configures the patch connection between the wave interface on the OSC module and the oscfilter interface on the OADM module. This is only required if an OSC module is present.