|
|
1. Check the packing slip to ensure that all the proper components are present.
2. Ensure that the site is set up properly:
3. Obtain the following equipment:
4. Ensure your safety when installing the Catalyst 5002 switch:
5. Take steps to prevent ESD damage to electronic components:
To rack-mount the Catalyst 5002 switch:
Attach the L brackets to the chassis using the four Phillips-head screws provided in the rack-mount kit.
1. With a person on each side of the chassis, lift and position the switch in the equipment rack.
2. Align the holes in the L brackets with the mounting holes in the equipment rack.
3. Insert the mounting screws through the holes in the L brackets and into the threaded holes in the mounting post.
4. Use a tape measure and level to ensure that the chassis is installed straight and level.
To connect the Catalyst 5002 switch to the network:
| Caution To prevent ESD damage to electronic components, always use an ESD wrist strap when handling modules or coming into contact with internal components. |
Use the procedure appropriate for the model of supervisor engine installed in your Catalyst 5002 switch:
To connect a terminal to the Supervisor Engine I or II console port, plug an EIA/TIA-232 (RS-232) DCE DB-25-to-DTE DB-25 straight-through cable into the console port.
To connect a terminal to the Supervisor Engine II G or III G console port, plug an RJ-45-to-RJ-45 straight-through cable into the console port jack. Use an RJ-45-to-DB-25 or RJ-45-to-DB-9 adapter to connect to the terminal.
The Catalyst 5000 series modules use the following connection types:
To connect to modules with RJ-45 interfaces, use Category 5 UTP (100BaseTX, 10/100BaseTX, CDDI, Token Ring, ATM), Category 3 UTP (10BaseT), or Type 1 FTP (Token Ring) cables with male RJ-45 interfaces.
Supervisor Engine I and II modules with 100BaseTX uplinks have MII ports in addition to RJ-45 ports. To connect to the MII interfaces, use Category 5 UTP cables with male MII connectors.
To connect to modules with RJ-21 Telco interfaces, use Category 3 UTP cable with male RJ-21 Telco connectors.
To connect to modules with SC-type fiber-optic interfaces, use single-mode or multimode fiber-optic cable with male SC-type connectors.
To connect to modules with ST-type fiber-optic interfaces, use single-mode (FDDI) or multimode (10BaseFL) fiber-optic cable with male ST-type connectors.
To connect to modules with MT-RJ interfaces, use multimode fiber-optic cables with MT-RJ connectors.
To connect to the FDDI module MMF (WS-X5101), use multimode fiber-optic cable with a male MIC-type connector.
To connect to the ATM dual PHY DS3 module (WS-X5166), use 75-ohm RG-59 coaxial cable with male BNC connectors.
| Caution To prevent ESD damage to electronic components, always use an ESD wrist strap when handling modules or coming into contact with internal components. |
A GBIC is a hot-swappable input/output device that plugs into the uplink ports of the Supervisor Engine II G and III G, and the Gigabit Ethernet ports of the Gigabit Ethernet switching modules.
1. Remove the GBIC from its protective packaging.
2. Grip the sides of the GBIC with your thumb and forefinger. Insert the GBIC into the slot on the front of the supervisor engine or switching module (see figure).
3. Slide the GBIC through the flap covering the slot opening until you hear a click.
4. Remove the plug from the GBIC and save it for future use.
5. Attach the fiber-optic cable with male SC-type connectors to the GBIC.
| Warning Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. |
| Caution To prevent ESD damage to electronic components, always use an ESD wrist strap when handling modules or coming into contact with internal components. |
Use the procedure appropriate for the type of power supplies used in your Catalyst 5002 switch:
1. Attach each power cable to a grounded outlet. If possible, connect each cable to an outlet on a separate circuit. Make sure that the source power is within range.
2. Do not connect the power cables to the power supplies until you are ready to boot the switch.
| Warning Before performing the following procedure, ensure that power is removed from the DC circuit. |
1. Verify that power is off to the DC-input circuit.
2. Wire the DC-input power supply to the terminal block (see figure), ensuring that all wire connections are secure (suggested DC-input wires are 14-AWG copper conductors):
3. On a new installation, remove the adhesive strip covering the CO ground connector.
4. Connect a 10- to 12-AWG copper conductor ground wire to the CO ground connector on the switch. Use a ground wire lug that is 0.320 inch (7.8 mm) or less.
5. Restore power to the DC circuit by turning the circuit breaker on (|).
1. Before you start the system, verify the following:
2. To power up the switch, plug the power cables into the power supplies. The switch begins the boot process.
3. Verify that the following occurs during the boot process:
4. Press Return at the Enter Password prompt to access the console command line.
| Caution To prevent ESD damage to electronic components, always use an ESD wrist strap when handling modules or coming into contact with internal components. |
Use the following procedures when inserting or removing Catalyst 5000 series modules:
1. Align the edges of the module with the slot guides on the sides of the chassis (see figure).
2. Ensure that the ejector levers are in the out position. Keeping the module horizontal, slide the module into the slot until the ejector levers contact the chassis.
3. Push both ejector levers in simultaneously to seat the module in the backplane connector.
4. Tighten the captive screws with a flat-blade screwdriver.
1. Loosen the captive screws on the module using a flat-blade screwdriver.
2. Pull the ejector levers outward simultaneously to release the module from the backplane connector.
3. Pull the module straight out of the slot and place it on an antistatic mat or in an antistatic bag.
Posted: Thu Jun 17 09:53:33 PDT 1999
Copyright 1989-1999©Cisco Systems Inc.
