|
|
Table Of Contents
Catalyst 5000 Family Network Analysis Module 128-MB SIMM Upgrade Installation and Configuration Note
Removing the Network Analysis Module
Installing the Network Analysis Module
Standards Compliance Specifications
Catalyst 5000 Family Network Analysis Module 128-MB SIMM Upgrade Installation and Configuration Note
Product Numbers:
MEM-C5K-NAM-UPGD(=) Network Analysis Module 128-MB Upgrade KitThis configuration note contains procedures for installing the 128-MB single inline memory module (SIMM) upgrade kit for the Catalyst 5000 family network analysis module.
Contents
This document contains the following sections:
•
Removing the Network Analysis Module
•
•
Required Tools
Note
The following tools are required to remove and replace the SIMM:
•
•
•
Note
Removing the Network Analysis Module
To install the SIMM, you must first remove the network analysis module from the switch.
CautionAlways use an ESD wrist strap when handling modules or coming into contact with internal components.
Figure 1 Ejector Levers and Captive Installation Screws
Note
To remove a network analysis module, perform these steps:
Warning
During this procedure, wear grounding wrist straps to avoid ESD damage to the module. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself.
Step 1
Step 2
Step 3
Step 4
the floor).Step 5
Installing the SIMMs
The SIMM slots are located on the motherboard of the network analysis module (see ). Once you remove the network analysis module from the Catalyst 5000 family switch, you can install the SIMMs.
CautionAlways use an ESD wrist strap when handling modules or coming into contact with internal components.
Figure 2 Supervisor Engine SIMM Slot Location
CautionHandle SIMMs by their edges only; avoid touching the memory module, pins, or traces (the metal fingers along the connector edge of a SIMM). SIMMs are sensitive components that are susceptible to ESD damage and can be damaged by mishandling.
To remove and replace the SIMMs, refer to and perform the following steps for each of the two SIMMs:
Step 1
Step 2
Step 3
Figure 3 Installing the 128-MB SIMM Set
Installing the Network Analysis Module
When installing the network analysis module, it can be installed in slots 2 through 5 in the Catalyst 5000 and Catalyst 5505 switches, slots 2 through 9 of the Catalyst 5509 switch, and slots 2 through 12 of the Catalyst 5500 switch. There is a limit of one Network Analysis Module per chassis.
CautionTo prevent ESD damage, handle switching modules by the carrier edges only.
Warning
During this procedure, wear grounding wrist straps to avoid ESD damage to the module. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself.
To install the network analysis module, follow these steps:
Step 1
Step 2
Figure 4 Installing the Network Analysis Module
Step 3
Step 4
Figure 5 Module Ejector Lever Operation
Step 5
Step 6
Step 7
Standards Compliance Specifications
Catalyst 5000 family modules, when intalled in a system, comply with the standards listed in :
Table 1 Standards Compliance Specifications
Compliance
CE1 Marking
Safety
UL2 1950, CSA3 -C22.2 No. 950, EN4 60950, IEC5 950, TS6 001, AS/NZS7 3260
EMI8
FCC9 Class A (47 CFR10 , Part 15), ICES11 -003 Class A, EN55022 Class A, CISPR22 Class A, AS/NZS 3548 Class A, and VCCI12 Class A with UTP13
EN55022 Class B, CISPR22 Class B, AS/NZS 3548 Class B, and VCCI Class B (Japan) with FTP14 cables
1 CE = European Compliance
2 UL = Underwriters Laboratory
3 CSA = Canadian Standards Association
4 EN = European Norm
5 IEC = International Electrotechnical Commission
6 TS = Technical Specification
7 AS/NZS = Standards Australia/Standards New Zealand
8 EMI = electromagnetic interference
9 FCC = Federal Communications Commission
10 CFR = Code of Federal Regulations
11 ICES = Interference-Causing Equipment Standard
12 VCCI = Voluntary Control Council for Information Technology Equipment
13 unshielded twisted-pair
14 foil twisted-pair
FCC Class A Compliance
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense.
You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures:
•
•
•
•
Modifications to this product not authorized by Cisco Systems could void the FCC approval and negate your authority to operate this product.
Related Documentation
For more detailed installation and configuration information, refer to the following publications:
•
•
•
•
If you are reading Cisco product documentation on the World Wide Web, you can submit comments electronically. Click Feedback in the toolbar and select Documentation. After you complete the form, click Submit to send it to Cisco. We appreciate your comments.
Cisco Connection Online
Cisco Connection Online (CCO) is Cisco Systems' primary, real-time support channel. Maintenance customers and partners can self-register on CCO to obtain additional information and services.
Available 24 hours a day, 7 days a week, CCO provides a wealth of standard and value-added services to Cisco's customers and business partners. CCO services include product information, product documentation, software updates, release notes, technical tips, the Bug Navigator, configuration notes, brochures, descriptions of service offerings, and download access to public and authorized files.
CCO serves a wide variety of users through two interfaces that are updated and enhanced simultaneously: a character-based version and a multimedia version that resides on the World Wide Web (WWW). The character-based CCO supports Zmodem, Kermit, Xmodem, FTP, and Internet e-mail, and it is excellent for quick access to information over lower bandwidths. The WWW version of CCO provides richly formatted documents with photographs, figures, graphics, and video, as well as hyperlinks to related information.
You can access CCO in the following ways:
•
•
•
•
•
For a copy of CCO's Frequently Asked Questions (FAQ), contact cco-help@cisco.com. For additional information, contact cco-team@cisco.com.
Note
Documentation CD-ROM
Cisco documentation and additional literature are available in a CD-ROM package, which ships with your product. The Documentation CD-ROM, a member of the Cisco Connection Family, is updated monthly. Therefore, it might be more current than printed documentation. To order additional copies of the Documentation CD-ROM, contact your local sales representative or call customer service. The CD-ROM package is available as a single package or as an annual subscription. You can also access Cisco documentation on the World Wide Web at http://www.cisco.com, http://www-china.cisco.com, or http://www-europe.cisco.com.
If you are reading Cisco product documentation on the World Wide Web, you can submit comments electronically. Click Feedback in the toolbar and select Documentation. After you complete the form, click Submit to send it to Cisco. We appreciate your comments.
78-10149-01 Rev. A0
Posted: Thu May 10 19:04:15 PDT 2007
All contents are Copyright © 1992--2007 Cisco Systems, Inc. All rights reserved.
Important Notices and Privacy Statement.
