Regulatory Compliance and Safety Information for the Catalyst 3560 Switch, January 2007

Regulatory Compliance and Safety Information for the Catalyst 3560 Switch

December 2006

Read this document before installing or servicing the Catalyst 3560 switch.

Warning IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device. Statement 1071

SAVE THESE INSTRUCTIONS

This document includes the following sections:

• Translated Safety Warnings

• European Directives

• Regulatory Standards Compliance

• EMC Environmental Conditions for Products Installed in the European Union

• EMC Class A Notices and Warnings

• Related Documentation

• Obtaining Documentation

• Documentation Feedback

• Cisco Product Security Overview

• Product Alerts and Field Notices

• Obtaining Technical Assistance

• Obtaining Additional Publications and Information

Translated Safety Warnings

This section includes translations in multiple languages of the warnings that may appear in your product documents.

Statement 17B—Overtemperature Warning


Warning	To prevent the switch from overheating, do not operate it in an area that exceeds the maximum recommended ambient temperature of 113°F (45°C). To prevent airflow restriction, allow at least 3 inches (7.6 cm) of clearance around the ventilation openings.
Waarschuwing	Om oververhitting van de schakelaar te voorkomen, mag u die niet bedienen in een ruimte die de maximale aanbevolen omgevingstemperatuur van 113°F (45°C) overschrijdt. Om beperking van de luchtstroom te voorkomen, dient u ten minste 3 inch (7,6 cm) speling te laten rondom de ventilatie-openingen.
Varoitus	Est��ksesi kytkimen ylikuumenemisen �l� k�yt� sit� sellaisissa paikoissa, joiden l�mp�tila ylitt�� ymp�rist�n enimm�isl�mp�tilaksi suositellun 45�C. J�t� v�hint��n 7,6 cm:n vapaa tila tuuletusaukkojen ymp�rille, jotta ilma p��see vapaasti virtaamaan.
Attention	Pour �viter une surchauffe du commutateur, ne pas le faire fonctionner dans un local dont la temp�rature ambiante d�passe le maximum recommand� de 45�C (113°F). Pour faciliter la circulation d'air, am�nager un d�gagement d'au moins 7,6 cm (3 pouces) autour des bouches d'a�ration.
Warnung	Um eine �berhitzung des Schalters zu vermeiden, ist das System nicht in einem Bereich zu betreiben, in dem die empfohlene H�chsttemperatur von 45�C �berschritten wird. Damit der Luftflu� nicht behindert wird, ist ein Freiraum von mindestens 7,6 cm um die Bel�ftungs�ffnungen herum einzuhalten.
Avvertenza	Per evitare il surriscaldamento dell'interruttore, non usare l'apparecchiatura in un'area che supera la temperatura ambientale minima consigliata di 45�C. Per evitare una limitazione del flusso dell'aria, lasciare come minimo uno spazio libero di 7,6 cm intorno alle aperture di ventilazione.
Advarsel	For � unng� at bryteren overopphetes skal utstyret ikke brukes p� steder hvor anbefalt maks omgivelsestemperatur overstiger 113 grader Farenheit (45�C). La det v�re minst 3 tommer (7,6 cm) klaring rundt ventilasjons�pningene for at luftsirkulasjonen skal v�re uhindret.
Aviso	Para evitar sobreaquecimento do interruptor, n�o utilize o equipamento numa �rea que exceda uma temperatura m�xima de 45�C. Para evitar o bloqueamento da circula��o de ar, deixe pelo menos um espa�o de 7.6 cm em volta das aberturas de ventila��o.
�Advertencia!	Para evitar que el interruptor se recaliente, no se debe usar en �reas cuya temperatura ambiente exceda la m�xima recomendada, esto es, 45�C (113�F). Para no entorpecer la corriente de aire, dejar por lo menos 7,6 cm (3 pulgadas) de espacio muerto alrededor de la rejilla de ventilaci�n.
Varning!	I syfte att undvika �verhettning av switchen skall den inte anv�ndas i utrymmen vars temperatur �verskrider den maximalt rekommenderade omgivningstemperaturen som �r 45�C. Kontrollera att det finns minst 7,6 cm fritt utrymme runt ventilations�ppningarna s� att luftfl�det inte begr�nsas.

Statement 43—Jewelry Removal Warning


Warning	Before working on equipment that is connected to power lines, remove jewelry (including rings, necklaces, and watches). Metal objects will heat up when connected to power and ground and can cause serious burns or weld the metal object to the terminals.
Waarschuwing	Alvorens aan apparatuur te werken die met elektrische leidingen is verbonden, sieraden (inclusief ringen, kettingen en horloges) verwijderen. Metalen voorwerpen worden warm wanneer ze met stroom en aarde zijn verbonden, en kunnen ernstige brandwonden veroorzaken of het metalen voorwerp aan de aansluitklemmen lassen.
Varoitus	Ennen kuin ty�skentelet voimavirtajohtoihin kytkettyjen laitteiden parissa, ota pois kaikki korut (sormukset, kaulakorut ja kellot mukaan lukien). Metalliesineet kuumenevat, kun ne ovat yhteydess� s�hk�virran ja maan kanssa, ja ne voivat aiheuttaa vakavia palovammoja tai hitsata metalliesineet kiinni liit�nt�napoihin.
Attention	Avant d'acc�der � cet �quipement connect� aux lignes �lectriques, �ter tout bijou (anneaux, colliers et montres compris). Lorsqu'ils sont branch�s � l'alimentation et reli�s � la terre, les objets m�talliques chauffent, ce qui peut provoquer des blessures graves ou souder l'objet m�tallique aux bornes.
Warnung	Vor der Arbeit an Ger�ten, die an das Netz angeschlossen sind, jeglichen Schmuck (einschlie�lich Ringe, Ketten und Uhren) abnehmen. Metallgegenst�nde erhitzen sich, wenn sie an das Netz und die Erde angeschlossen werden, und k�nnen schwere Verbrennungen verursachen oder an die Anschlu�klemmen angeschwei�t werden.
Avvertenza	Prima di intervenire su apparecchiature collegate alle linee di alimentazione, togliersi qualsiasi monile (inclusi anelli, collane, braccialetti ed orologi). Gli oggetti metallici si riscaldano quando sono collegati tra punti di alimentazione e massa: possono causare ustioni gravi oppure il metallo pu� saldarsi ai terminali.
Advarsel	Fjern alle smykker (inkludert ringer, halskjeder og klokker) f�r du skal arbeide p� utstyr som er koblet til kraftledninger. Metallgjenstander som er koblet til kraftledninger og jord blir sv�rt varme og kan for�rsake alvorlige brannskader eller smelte fast til polene.
Aviso	Antes de trabalhar em equipamento que esteja ligado a linhas de corrente, retire todas as j�ias que estiver a usar (incluindo an�is, fios e rel�gios). Os objectos met�licos aquecer�o em contacto com a corrente e em contacto com a liga��o � terra, podendo causar queimaduras graves ou ficarem soldados aos terminais.
�Advertencia!	Antes de operar sobre equipos conectados a l�neas de alimentaci�n, quitarse las joyas (incluidos anillos, collares y relojes). Los objetos de metal se calientan cuando se conectan a la alimentaci�n y a tierra, lo que puede ocasionar quemaduras graves o que los objetos met�licos queden soldados a los bornes.
Varning!	Tag av alla smycken (inklusive ringar, halsband och armbandsur) innan du arbetar p� utrustning som �r kopplad till kraftledningar. Metallobjekt hettas upp n�r de kopplas ihop med str�m och jord och kan f�rorsaka allvarliga br�nnskador; metallobjekt kan ocks� sammansvetsas med kontakterna.

Statement 48—Stacking the Chassis Warning


Warning	Do not stack the chassis on any other equipment. If the chassis falls, it can cause severe bodily injury and equipment damage.
Waarschuwing	Het chassis mag niet op andere apparatuur gestapeld te worden. Als het chassis mocht vallen, kan dit ernstig lichamelijk letsel en beschadiging van de apparatuur veroorzaken.
Varoitus	�l� aseta asennuspohjaa mink��n muun laitteen p��lle. Asennuspohja voi pudotessaan aiheuttaa vaikean ruumiinvamman tai laitevaurion.
Avertissement	Ne placez pas ce ch�ssis sur un autre appareil. En cas de chute, il pourrait provoquer de graves blessures corporelles et d'importants dommages.
Achtung	Das Geh�use nicht auf andere Ger�te stellen. Wenn das Geh�use herunterf�llt, besteht Gefahr schwerer Personenverletzungen und Ger�tesch�den.
Avvertenza	Non collocare lo chassis su nessun altro apparecchio. Se lo chassis cade, pu� causare lesioni gravi e danni alle apparecchiature.
Advarsel	Stable ikke kabinettet opp� annet utstyr. Hvis kabinettet faller, kan det for�rsake alvorlig skade p� mennesker og utstyr.
Aviso	N�o coloque o chassis em cima de qualquer outro equipamento. Se o chassis cair, poder� causar ferimentos graves e danos no equipamento.
�Atenci�n!	No apilar los chasis sobre ning�n otro equipo. Si el chasis se cae al suelo puede causar graves lesiones f�sicas y da�os al equipo.
Varning	Placera inte chassit ovanp� annan utrustning. Om chassit faller kan allvarlig kroppsskada s�v�l som skada p� utrustningen uppst�.

Statement 100C—Attaching the Cisco RPS (model PWR675-AC-RPS-N1)


Warning	Attach only the Cisco RPS (model PWR675-AC-RPS-N1) to the RPS receptacle.
Waarschuwing	Slechts de Cisco RPS (model PWR675-AC-RPS-N1) aan de RPS contactdoos verbinden.
Varoitus	Kiinnit� RPS-vastakappaleeseen vain Cisco RPS (malli PWR675-AC-RPS-N1).
Avertissement	Raccordez le bloc d'alimentation Cisco RPS (mod�le PWR675-AC-RPS-N1) uniquement au connecteur RPS.
Warnung	An die RPS-Steckh�lse darf nur das Cisco RPS (Modell PWR675-AC-RPS-N1) angeschlossen werden.
Avvertenza	Collegare soltanto il Cisco RPS (modello PWR675-AC-RPS-N1) alla presa RPS.
Advarsel!	Koble bare Cisco RPS (modell PWR675-AC-RPS-N1) til RPS-stikkontakten.
Aviso	Anexe o RPS Cisco (modelo PWR675-AC-RPS-N1) apenas ao recept�culo RPS.
�Advertencia!	S�lo conecte el Cisco RPS (modelo PWR675-AC-RPS-N1) al recept�culo RPS.
Varning!	Koppla endast Ciscos RPS (modell PWR675-AC-RPS-N1) till RPS-uttaget.

Statement 171—Ethernet Cable Shielding in Offices


Warning	Ethernet cables must be shielded when used in a central office environment.
Waarschuwing	Ethernetkabels dienen beveiligd te worden als ze in een centrale kantooromgeving worden gebruikt.
Varoitus	Ethernet-kaapelit t�ytyy suojata, kun niit� k�ytet��n yleisess� toimistoymp�rist�ss�.
Attention	Pour une utilisation en site central, les c�bles Ethernet doivent �tre imp�rativement blind�s.
Warnung	Ethernet-Kabel m�ssen abgeschirmt werden, wenn sie in einer Zentrale eingesetzt werden.
Avvertenza	I cavi Ethernet devono essere schermati se utilizzati in un ambiente di ufficio centrale.
Advarsel	Ethernet-kabler skal v�re skjermet n�r de brukes i et sentralt kontormilj�.
Aviso	Os cabos "Ethernet" dever�o estar armados quando usados em ambiente de escrit�rio central.
�Advertencia!	Los cables Ethernet deben estar protegidos cuando se usen dentro de una oficina central.
Varning!	Ethernetkablar m�ste vara avsk�rmade vid anv�ndning i central kontorsmilj�.

Statement 265—RPS Connection Warning


Warning	If a redundant power system (RPS) is not connected to the switch, install an RPS connector cover on the back of the switch.
Waarschuwing	Als er geen redundant voedingssysteem (RPS) aan de schakelaar is gekoppeld, dient u een RPS-connectorkapje op de achterkant van de schakelaar te installeren.
Varoitus	Jos korvautuvaa tehoj�rjestelm�� (redundant power system, RPS) ei ole liitetty kytkimeen, kiinnit� RPS-liittimen suojus kytkimen takapuolelle.
Attention	Si un syst�me d'alimentation �lectrique redondant (RPS) n'est pas connect� au commutateur, installez un cache de connecteur RPS � l'arri�re du commutateur.
Warnung	Wenn keine redundante Stromversorgung (RSV) an den Schalter angeschlossen ist, eine RSV-Steckerabdeckung an der R�ckseite des Schalters anbringen.
Avvertenza	Se un sistema RPS (Redundant Power System ) di alimentazione ridondante non � collegato al dispositivo switch, installare un copri-connettore RPS sul retro del switch.
Advarsel	Dersom et redundant str�msystem ( Redundant Power System -RPS) ikke er koblet til bryteren, skal det installeres et RPS-koblingsdeksel p� baksiden av bryteren.
Aviso	Se um sistema de alimenta��o redundante (RPS) n�o estiver conectado a um switch, instale uma capa de conector RPS na parte de tr�s do switch.
�Advertencia!	Si no se conecta un sistema de potencia redundante (RPS) al interruptor, instale una cubierta de conector RPS en la parte posterior del interruptor.
Varning!	Om ett redundant str�mf�rs�rjningssystem (redundant power system, RPS) inte finns anslutet till switchen skall ett RPS-kontaktskydd installeras p� switchens baksida.

Statement 266—Switch Installation Warning


Warning	To comply with safety regulations, mount switches on a wall with the front panel facing up.
Waarschuwing	Om te voldoen aan de veiligheidsvoorschriften dient u de schakelaars op een muur te monteren met het voorpaneel omhoog.
Varoitus	Turvallisuusm��r�ykset edellytt�v�t, ett� kytkimet kiinnitet��n sein��n etupaneeli yl�sp�in.
Attention	Pour satisfaire aux dispositions de s�curit�, installez les commutateurs muraux avec le panneau frontal vers le haut.
Warnung	Zur Einhaltung der Sicherheitsvorschriften die Schalter so an einer Wand montieren, dass die Frontplatte nach oben zeigt.
Avvertenza	In conformit� ai regolamenti di sicurezza, installare i dispositivi switch a muro con il pannello frontale rivolto in su.
Advarsel	For � etterkomme sikkerhetsreglene skal brytere monteres p� en vegg med frontpanelet vendt opp.
Aviso	Para cumprir com os regulamentos de seguran�a, fa�a a montagem de switches em uma parede com o painel frontal virado para cima.
�Advertencia!	Para cumplir con las reglas de seguridad, instale los interruptores en una pared con el panel del frente hacia arriba.
Varning!	F�r att uppfylla s�kerhetsf�reskrifter skall switcharna monteras p� en v�gg med frampanelen riktad upp�t.

Statement 1001—Work During Lightning Activity


Warning	Do not work on the system or connect or disconnect cables during periods of lightning activity.
Waarschuwing	Tijdens onweer dat gepaard gaat met bliksem, dient u niet aan het systeem te werken of kabels aan te sluiten of te ontkoppelen.
Varoitus	�l� ty�skentele j�rjestelm�n parissa �l�k� yhdist� tai irrota kaapeleita ukkosilmalla.
Attention	Ne pas travailler sur le syst�me ni brancher ou d�brancher les c�bles pendant un orage.
Warnung	Arbeiten Sie nicht am System und schlie�en Sie keine Kabel an bzw. trennen Sie keine ab, wenn es gewittert.
Avvertenza	Non lavorare sul sistema o collegare oppure scollegare i cavi durante un temporale con fulmini.
Advarsel	Utf�r aldri arbeid p� systemet, eller koble kabler til eller fra systemet n�r det tordner eller lyner.
Aviso	N�o trabalhe no sistema ou ligue e desligue cabos durante per�odos de mau tempo (trovoada).
�Advertencia!	No operar el sistema ni conectar o desconectar cables durante el transcurso de descargas el�ctricas en la atm�sfera.
Varning!	Vid �ska skall du aldrig utf�ra arbete p� systemet eller ansluta eller koppla loss kablar.

Statement 1004—Installation Instructions


Warning	Read the installation instructions before connecting the system to the power source.
Waarschuwing	Raadpleeg de installatie-instructies voordat u het systeem op de voedingsbron aansluit.
Varoitus	Lue asennusohjeet ennen j�rjestelm�n yhdist�mist� virtal�hteeseen.
Attention	Avant de brancher le syst�me sur la source d'alimentation, consulter les directives d'installation.
Warnung	Vor dem Anschlie�en des Systems an die Stromquelle die Installationsanweisungen lesen.
Avvertenza	Consultare le istruzioni di installazione prima di collegare il sistema all'alimentatore.
Advarsel	Les installasjonsinstruksjonene f�r systemet kobles til str�mkilden.
Aviso	Leia as instru��es de instala��o antes de ligar o sistema � fonte de energia.
�Advertencia!	Lea las instrucciones de instalaci�n antes de conectar el sistema a la red de alimentaci�n.
Varning!	L�s installationsanvisningarna innan du kopplar systemet till str�mf�rs�rjningsenheten.

Statement 1006—Chassis Warning for Rack-Mounting and Servicing


Warning	To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to ensure that the system remains stable. The following guidelines are provided to ensure your safety: •This unit should be mounted at the bottom of the rack if it is the only unit in the rack. •When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the heaviest component at the bottom of the rack. •If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in the rack.
Waarschuwing	Om lichamelijk letsel te voorkomen wanneer u dit toestel in een rek monteert of het daar een servicebeurt geeft, moet u speciale voorzorgsmaatregelen nemen om ervoor te zorgen dat het toestel stabiel blijft. De onderstaande richtlijnen worden verstrekt om uw veiligheid te verzekeren: •Dit toestel dient onderaan in het rek gemonteerd te worden als het toestel het enige in het rek is. •Wanneer u dit toestel in een gedeeltelijk gevuld rek monteert, dient u het rek van onderen naar boven te laden met het zwaarste onderdeel onderaan in het rek. •Als het rek voorzien is van stabiliseringshulpmiddelen, dient u de stabilisatoren te monteren voordat u het toestel in het rek monteert of het daar een servicebeurt geeft.
Varoitus	Kun laite asetetaan telineeseen tai huolletaan sen ollessa telineess�, on noudatettava erityisi� varotoimia j�rjestelm�n vakavuuden s�ilytt�miseksi, jotta v�ltyt��n loukkaantumiselta. Noudata seuraavia turvallisuusohjeita: •Jos telineess� ei ole muita laitteita, aseta laite telineen alaosaan. •Jos laite asetetaan osaksi t�ytettyyn telineeseen, aloita kuormittaminen sen alaosasta kaikkein raskaimmalla esineell� ja siirry sitten sen yl�osaan. •Jos telinett� varten on vakaimet, asenna ne ennen laitteen asettamista telineeseen tai sen huoltamista siin�.
Attention	Pour �viter toute blessure corporelle pendant les op�rations de montage ou de r�paration de cette unit� en casier, il convient de prendre des pr�cautions sp�ciales afin de maintenir la stabilit� du syst�me. Les directives ci-dessous sont destin�es � assurer la protection du personnel�: •Si cette unit� constitue la seule unit� mont�e en casier, elle doit �tre plac�e dans le bas. •Si cette unit� est mont�e dans un casier partiellement rempli, charger le casier de bas en haut en pla�ant l'�l�ment le plus lourd dans le bas. •Si le casier est �quip� de dispositifs stabilisateurs, installer les stabilisateurs avant de monter ou de r�parer l'unit� en casier.
Warnung	Zur Vermeidung von K�rperverletzung beim Anbringen oder Warten dieser Einheit in einem Gestell m�ssen Sie besondere Vorkehrungen treffen, um sicherzustellen, da� das System stabil bleibt. Die folgenden Richtlinien sollen zur Gew�hrleistung Ihrer Sicherheit dienen: •Wenn diese Einheit die einzige im Gestell ist, sollte sie unten im Gestell angebracht werden. •Bei Anbringung dieser Einheit in einem zum Teil gef�llten Gestell ist das Gestell von unten nach oben zu laden, wobei das schwerste Bauteil unten im Gestell anzubringen ist. •Wird das Gestell mit Stabilisierungszubeh�r geliefert, sind zuerst die Stabilisatoren zu installieren, bevor Sie die Einheit im Gestell anbringen oder sie warten.
Avvertenza	Per evitare infortuni fisici durante il montaggio o la manutenzione di questa unit� in un supporto, occorre osservare speciali precauzioni per garantire che il sistema rimanga stabile. Le seguenti direttive vengono fornite per garantire la sicurezza personale: •Questa unit� deve venire montata sul fondo del supporto, se si tratta dell'unica unit� da montare nel supporto. •Quando questa unit� viene montata in un supporto parzialmente pieno, caricare il supporto dal basso all'alto, con il componente pi� pesante sistemato sul fondo del supporto. •Se il supporto � dotato di dispositivi stabilizzanti, installare tali dispositivi prima di montare o di procedere alla manutenzione dell'unit� nel supporto.
Advarsel	Unng� fysiske skader under montering eller reparasjonsarbeid p� denne enheten n�r den befinner seg i et kabinett. V�r n�ye med at systemet er stabilt. F�lgende retningslinjer er gitt for � verne om sikkerheten: •Denne enheten b�r monteres nederst i kabinettet hvis dette er den eneste enheten i kabinettet. •Ved montering av denne enheten i et kabinett som er delvis fylt, skal kabinettet lastes fra bunnen og opp med den tyngste komponenten nederst i kabinettet. •Hvis kabinettet er utstyrt med stabiliseringsutstyr, skal stabilisatorene installeres f�r montering eller utf�ring av reparasjonsarbeid p� enheten i kabinettet.
Aviso	Para se prevenir contra danos corporais ao montar ou reparar esta unidade numa estante, dever� tomar precau��es especiais para se certificar de que o sistema possui um suporte est�vel. As seguintes directrizes ajud�-lo-�o a efectuar o seu trabalho com seguran�a: •Esta unidade dever� ser montada na parte inferior da estante, caso seja esta a �nica unidade a ser montada. •Ao montar esta unidade numa estante parcialmente ocupada, coloque os itens mais pesados na parte inferior da estante, arrumando-os de baixo para cima. •Se a estante possuir um dispositivo de estabiliza��o, instale-o antes de montar ou reparar a unidade.
�Advertencia!	Para evitar lesiones durante el montaje de este equipo sobre un bastidor, o posteriormente durante su mantenimiento, se debe poner mucho cuidado en que el sistema quede bien estable. Para garantizar su seguridad, proceda seg�n las siguientes instrucciones: •Colocar el equipo en la parte inferior del bastidor, cuando sea la �nica unidad en el mismo. •Cuando este equipo se vaya a instalar en un bastidor parcialmente ocupado, comenzar la instalaci�n desde la parte inferior hacia la superior colocando el equipo m�s pesado en la parte inferior. •Si el bastidor dispone de dispositivos estabilizadores, instalar �stos antes de montar o proceder al mantenimiento del equipo instalado en el bastidor.
Varning!	F�r att undvika kroppsskada n�r du installerar eller utf�r underh�llsarbete p� denna enhet p� en st�llning m�ste du vidta s�rskilda f�rsiktighets�tg�rder f�r att f�rs�kra dig om att systemet st�r stadigt. F�ljande riktlinjer ges f�r att trygga din s�kerhet: •Om denna enhet �r den enda enheten p� st�llningen skall den installeras l�ngst ned p� st�llningen. •Om denna enhet installeras p� en delvis fylld st�llning skall st�llningen fyllas nedifr�n och upp, med de tyngsta enheterna l�ngst ned p� st�llningen. •Om st�llningen �r f�rsedd med stabiliseringsdon skall dessa monteras fast innan enheten installeras eller underh�lls p� st�llningen.





Aviso	Para evitar les�es corporais ao montar ou dar manuten��o a esta unidade em um rack, � necess�rio tomar todas as precau��es para garantir a estabilidade do sistema. As seguintes orienta��es s�o fornecidas para garantir a sua seguran�a: •Se esta for a �nica unidade, ela dever� ser montada na parte inferior do rack. •Ao montar esta unidade em um rack parcialmente preenchido, carregue-o de baixo para cima com o componente mais pesado em sua parte inferior. •Se o rack contiver dispositivos estabilizadores, instale-os antes de montar ou dar manuten��o � unidade existente.
Advarsel	For at forhindre legemesbeskadigelse ved montering eller service af denne enhed i et rack, skal du sikre at systemet st�r stabilt. F�lgende retningslinjer er ogs� for din sikkerheds skyld: •Enheden skal monteres i bunden af dit rack, hvis det er den eneste enhed i racket. •Ved montering af denne enhed i et delvist fyldt rack, skal enhederne installeres fra bunden og opad med den tungeste enhed nederst. •Hvis racket leveres med stabiliseringsenheder, skal disse installeres for enheden monteres eller serviceres i racket.

Statement 1008—Class 1 Laser Product


Warning	Class 1 laser product.
Waarschuwing	Klasse-1 laser produkt.
Varoitus	Luokan 1 lasertuote.
Attention	Produit laser de classe 1.
Warnung	Laserprodukt der Klasse 1.
Avvertenza	Prodotto laser di Classe 1.
Advarsel	Laserprodukt av klasse 1.
Aviso	Produto laser de classe 1.
�Advertencia!	Producto l�ser Clase I.
Varning!	Laserprodukt av klass 1.





Aviso	Produto a laser de classe 1.
Advarsel	Klasse 1 laserprodukt.

Statement 1017—Restricted Area


Warning	This unit is intended for installation in restricted access areas. A restricted access area can be accessed only through the use of a special tool, lock and key, or other means of security.
Waarschuwing	Deze eenheid is bestemd voor installatie in plaatsen met beperkte toegang. Toegang tot een dergelijke plaats kan alleen verkregen worden door middel van een speciaal instrument, een slot en sleutel of een ander veiligheidsmiddel.
Varoitus	T�m� laite on tarkoitettu asennettavaksi paikkaan, johon p��sy on rajoitettua. T�llaiseen paikkaan p��see vain erikoisty�kalua, lukkoon sopivaa avainta tai jotakin muuta turvalaitetta k�ytt�m�ll�.
Attention	Cet appareil est � installer dans des zones d'acc�s r�serv�. L'acc�s � une zone d'acc�s r�serv� n'est possible qu'en utilisant un outil sp�cial, un m�canisme de verrouillage et une cl�, ou tout autre moyen de s�curit�.
Warnung	Diese Einheit ist zur Installation in Bereichen mit beschr�nktem Zutritt vorgesehen. Der Zutritt zu derartigen Bereichen ist nur mit einem Spezialwerkzeug, Schloss und Schl�ssel oder einer sonstigen Sicherheitsvorkehrung m�glich.
Avvertenza	Questa unit� � prevista per essere installata in un'area ad accesso limitato, vale a dire un'area accessibile solo mediante l'uso di un attrezzo speciale, come lucchetto e chiave, o altri dispositivi di sicurezza.
Advarsel	Denne enheten er beregnet p� installasjon i omr�der med begrenset tilgang. Et begrenset tilgangsomr�de kan bare n�s ved hjelp av et spesielt verkt�y, l�s og n�kkel, eller andre sikkerhetsanordninger.
Aviso	Esta unidade foi concebida para instala��o em �reas de acesso restrito. Uma �rea de acesso restrito � uma �rea � qual apenas tem acesso o pessoal de servi�o autorizado, que possua uma ferramenta, chave e fechadura especial, ou qualquer outra forma de seguran�a.
�Advertencia!	Esta unidad ha sido dise�ada para instalaci�n en �reas de acceso restringido. S�lo puede obtenerse acceso a una de estas �reas mediante la utilizaci�n de una herramienta especial, cerradura con llave u otro medio de seguridad.
Varning!	Denna enhet �r avsedd f�r installation i omr�den med begr�nsat tilltr�de. Ett omr�de med begr�nsat tilltr�de kan endast tilltr�das med hj�lp av specialverktyg, l�s och nyckel eller annan s�kerhetsanordning.





Aviso	Esta unidade deve ser instalada em �reas de acesso restrito. Uma �rea de acesso restrito s� pode ser acessada com o uso de uma ferramenta especial, cadeado e chave ou outros meios de seguran�a.
Advarsel	Denne enhed er beregnet til installation i omr�der med begr�nset adgang. Der kan kun opn�s adgang til et begr�nset omr�de ved at bruge et s�rligt stykke v�rkt�j, l�s og n�gle, eller en anden form for sikkerhed.

Statement 1019—Main Disconnecting Device


Warning	The plug-socket combination must be accessible at all times, because it serves as the main disconnecting device.
Waarschuwing	De combinatie van de stekker en het elektrisch contactpunt moet te allen tijde toegankelijk zijn omdat deze het hoofdmechanisme vormt voor verbreking van de aansluiting.
Varoitus	Pistoke/liitinkohta toimii p��katkaisumekanismina. P��sy siihen on pidett�v� aina esteett�m�n�.
Attention	La combinaison de prise de courant doit �tre accessible � tout moment parce qu'elle fait office de syst�me principal de d�connexion.
Warnung	Der Netzkabelanschlu� am Ger�t mu� jederzeit zug�nglich sein, weil er als prim�re Ausschaltvorrichtung dient.
Avvertenza	Il gruppo spina-presa deve essere sempre accessibile, poich� viene utilizzato come dispositivo di scollegamento principale.
Advarsel	Kombinasjonen st�psel/uttak m� alltid v�re tilgjengelig ettersom den fungerer som hovedfrakoplingsenhet.
Aviso	A combina��o ficha-tomada dever� ser sempre acess�vel, porque funciona como interruptor principal.
�Advertencia!	El conjunto de clavija y toma ha de encontrarse siempre accesible ya que hace las veces de dispositivo de desconexi�n principal.
Varning!	Man m�ste alltid kunna komma �t stickproppen i uttaget, eftersom denna koppling utg�r den huvudsakliga fr�nkopplingsanordningen.

Statement 1024—Ground Conductor


Warning	This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available. Statement 1024
Waarschuwing	Deze apparatuur dient geaard te zijn. De aardingsleiding mag nooit buiten werking worden gesteld en de apparatuur mag nooit bediend worden zonder dat er een op de juiste wijze ge�nstalleerde aardingsleiding aanwezig is. Neem contact op met de bevoegde instantie voor elektrische inspecties of met een elektricien als u er niet zeker van bent dat er voor passende aarding gezorgd is.
Varoitus	Laitteiden on oltava maadoitettuja. �l� koskaan ohita maajohdinta tai k�yt� laitteita ilman oikein asennettua maajohdinta. Ota yhteys s�hk�tarkastusviranomaiseen tai s�hk�asentajaan, jos olet ep�varma maadoituksen sopivuudesta.
Attention	Cet �quipement doit �tre mis � la masse. Ne jamais rendre inop�rant le conducteur de masse ni utiliser l'�quipement sans un conducteur de masse ad�quatement install�. En cas de doute sur la mise � la masse appropri�e disponible, s'adresser � l'organisme responsable de la s�curit� �lectrique ou � un �lectricien.
Warnung	Dieses Ger�t muss geerdet sein. Auf keinen Fall den Erdungsleiter unwirksam machen oder das Ger�t ohne einen sachgerecht installierten Erdungsleiter verwenden. Wenn Sie sich nicht sicher sind, ob eine sachgerechte Erdung vorhanden ist, wenden Sie sich an die zust�ndige Inspektionsbeh�rde oder einen Elektriker.
Avvertenza	Questa apparecchiatura deve essere dotata di messa a terra. Non escludere mai il conduttore di protezione n� usare l'apparecchiatura in assenza di un conduttore di protezione installato in modo corretto. Se non si � certi della disponibilit� di un adeguato collegamento di messa a terra, richiedere un controllo elettrico presso le autorit� competenti o rivolgersi a un elettricista.
Advarsel	Dette utstyret m� jordes. Omg� aldri jordingslederen og bruk aldri utstyret uten riktig montert jordingsleder. Ta kontakt med fagfolk innen elektrisk inspeksjon eller med en elektriker hvis du er usikker p� om det finnes velegnet jordning.
Aviso	Este equipamento deve ser aterrado. Nunca anule o fio terra nem opere o equipamento sem um aterramento adequadamente instalado. Em caso de d�vida com rela��o ao sistema de aterramento dispon�vel, entre em contato com os servi�os locais de inspe��o el�trica ou um eletricista qualificado.
�Advertencia!	Este equipo debe estar conectado a tierra. No inhabilite el conductor de tierra ni haga funcionar el equipo si no hay un conductor de tierra instalado correctamente. P�ngase en contacto con la autoridad correspondiente de inspecci�n el�ctrica o con un electricista si no est� seguro de que haya una conexi�n a tierra adecuada.
Varning!	Denna utrustning m�ste jordas. Koppla aldrig fr�n jordledningen och anv�nd aldrig utrustningen utan en p� l�mpligt s�tt installerad jordledning. Om det f�religger os�kerhet huruvida l�mplig jordning finns skall elektrisk besiktningsauktoritet eller elektriker kontaktas.

Statement 1028—More Than One Power Supply


Warning	This unit might have more than one power supply connection. All connections must be removed to de-energize the unit. Statement 1028
Waarschuwing	Deze eenheid kan meer dan ��n stroomtoevoeraansluiting bevatten. Alle aansluitingen dienen ontkoppeld te worden om de eenheid te ontkrachten.
Varoitus	T�ss� laitteessa voi olla useampia kuin yksi virtakytkent�. Kaikki liit�nn�t on irrotettava, jotta j�nnite poistetaan laitteesta.
Attention	Cette unit� peut avoir plus d'une connexion d'alimentation. Pour supprimer toute tension et tout courant �lectrique de l'unit�, toutes les connexions d'alimentation doivent �tre d�branch�es.
Warnung	Dieses Ger�t kann mehr als eine Stromzufuhr haben. Um sicherzustellen, dass der Einheit kein Strom zugef�hrt wird, m�ssen alle Verbindungen entfernt werden.
Avvertenza	Questa unit� pu� avere pi� di una connessione all'alimentazione elettrica. Tutte le connessioni devono essere staccate per togliere la corrente dall'unit�.
Advarsel	Denne enheten kan ha mer enn �n str�mtilf�rselskobling. Alle koblinger m� fjernes fra enheten for � utkoble all str�m.
Aviso	Esta unidade poder� ter mais de uma conex�o de fonte de energia. Todas as conex�es devem ser removidas para desligar a unidade.
�Advertencia!	Puede que esta unidad tenga m�s de una conexi�n para fuentes de alimentaci�n. Para cortar por completo el suministro de energ�a, deben desconectarse todas las conexiones.
Varning!	Denna enhet har eventuellt mer �n en str�mf�rs�rjningsanslutning. Alla anslutningar m�ste tas bort f�r att g�ra enheten str�ml�s.





Aviso	Esta unidade pode ter mais de uma conex�o de fonte de alimenta��o. Todas as conex�es devem ser removidas para interromper a alimenta��o da unidade.
Advarsel	Denne enhed har muligvis mere end en str�mforsyningstilslutning. Alle tilslutninger skal fjernes for at aflade str�mmen fra enheden.

Statement 1030—Equipment Installation


Warning	Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Waarschuwing	Deze apparatuur mag alleen worden ge�nstalleerd, vervangen of hersteld door bevoegd geschoold personeel.
Varoitus	T�m�n laitteen saa asentaa, vaihtaa tai huoltaa ainoastaan koulutettu ja laitteen tunteva henkil�kunta.
Attention	Il est vivement recommand� de confier l'installation, le remplacement et la maintenance de ces �quipements � des personnels qualifi�s et exp�riment�s.
Warnung	Das Installieren, Ersetzen oder Bedienen dieser Ausr�stung sollte nur geschultem, qualifiziertem Personal gestattet werden.
Avvertenza	Questo apparato pu� essere installato, sostituito o mantenuto unicamente da un personale competente.
Advarsel	Bare oppl�rt og kvalifisert personell skal foreta installasjoner, utskiftninger eller service p� dette utstyret.
Aviso	Apenas pessoal treinado e qualificado deve ser autorizado a instalar, substituir ou fazer a revis�o deste equipamento.
�Advertencia!	Solamente el personal calificado debe instalar, reemplazar o utilizar este equipo.
Varning!	Endast utbildad och kvalificerad personal b�r f� till�telse att installera, byta ut eller reparera denna utrustning.





Aviso	Somente uma equipe treinada e qualificada tem permiss�o para instalar, substituir ou dar manuten��o a este equipamento.
Advarsel	Kun uddannede personer m� installere, udskifte komponenter i eller servicere dette udstyr.

Statement 1040—Product Disposal


Warning	Ultimate disposal of this product should be handled according to all national laws and regulations.
Waarschuwing	Het uiteindelijke wegruimen van dit product dient te geschieden in overeenstemming met alle nationale wetten en reglementen.
Varoitus	T�m� tuote on h�vitett�v� kansallisten lakien ja m��r�ysten mukaisesti.
Attention	La mise au rebut ou le recyclage de ce produit sont g�n�ralement soumis � des lois et/ou directives de respect de l'environnement. Renseignez-vous aupr�s de l'organisme comp�tent.
Warnung	Die Entsorgung dieses Produkts sollte gem�� allen Bestimmungen und Gesetzen des Landes erfolgen.
Avvertenza	Lo smaltimento di questo prodotto deve essere eseguito secondo le leggi e regolazioni locali.
Advarsel	Endelig kassering av dette produktet skal v�re i henhold til alle relevante nasjonale lover og bestemmelser.
Aviso	Deitar fora este produto em conformidade com todas as leis e regulamentos nacionais.
�Advertencia!	Al deshacerse por completo de este producto debe seguir todas las leyes y reglamentos nacionales.
Varning!	Vid deponering hanteras produkten enligt g�llande lagar och best�mmelser.





Aviso	O descarte definitivo deste produto deve estar de acordo com todas as leis e regulamenta��es nacionais.
Advarsel	Endelig bortskaffelse af dette produkt skal ske i henhold til g�ldende love og regler.

Statement 1044—Port Connections


Warning	For connections outside the building where the equipment is installed, the following ports must be connected through an approved network termination unit with integral circuit protection: 10/100/1000 Ethernet.
Waarschuwing	Voor aansluitingen buiten het gebouw waar de apparatuur wordt ge�nstalleerd, dienen de volgende poorten aangesloten te worden via een goedgekeurde netwerkafsluiteenheid met integrale circuitbescherming. 10/100/1000 Ethernet
Varoitus	Asennuksen sis�lt�v�n rakennuksen ulkopuolisia liit�nt�j� varten seuraavat portit on kytkett�v� hyv�ksytyn verkon p��telaitteen kautta ja virtapiirin on oltava kiinte�sti suojattu. 10/100/1000 Ethernet
Attention	Pour les connexions ext�rieures au b�timent �quip�, les ports suivants doivent �tre connect�s � un point approuv� de terminaison de r�seau, avec protection compl�te du circuit. 10/100/1000 Ethernet
Warnung	F�r Verbindungen au�erhalb des Geb�udes, in dem das Ger�t installiert ist, m�ssen die folgenden Anschl�sse �ber eine zul�ssige Netzabschlusseinheit mit integralem Leitungsschutz verbunden werden. 10/100/1000 Ethernet
Avvertenza	Per le connessioni esterne all'edificio in cui � installato l'apparecchio, le seguenti porte devono essere connesse a un'unit� di terminazione di rete approvata, con protezione completa del circuito. 10/100/1000 Ethernet
Advarsel	For tilkoblinger utenfor bygningen der utstyret er montert, m� f�lgende �pninger tilkobles gjennom en godkjent nettverksterminal med integrert kretsbeskyttelse. 10/100/1000 Ethernet
Aviso	Para liga��es fora do edif�cio onde o equipamento est� instalado, � necess�rio ligar as seguintes portas atrav�s de uma unidade de terminal de rede aprovada com protec��o de circuito integral. 10/100/1000 Ethernet
�Advertencia!	Para realizar conexiones en el exterior del edificio en el que est� instalado el equipo, deber� conectar los puertos especificados a continuaci�n a una unidad terminal de red aprobada que cuente con protecci�n de circuitos integrales. 10/100/1000 Ethernet
Varning!	F�r alla anslutningar utanf�r byggnaden d�r utrustningen har installerats g�ller att f�ljande portar m�ste anslutas genom en godk�nd n�tverksavslutningsenhet med integrerat kretsskydd. 10/100/1000 Ethernet
	10/100/1000 Ethernet
	10/100/1000 Ethernet
	10/100/1000 Ethernet
	10/100/1000 Ethernet

Statement 1046—Installing or Replacing the Unit


Warning	When installing or replacing the unit, the ground connection must always be made first and disconnected last.
Waarschuwing	Bij installatie of vervanging van het toestel moet de aardverbinding altijd het eerste worden gemaakt en het laatste worden losgemaakt.
Varoitus	Laitetta asennettaessa tai korvattaessa on maahan yhdist�minen aina teht�v� ensiksi ja maadoituksen irti kytkeminen viimeiseksi.
Attention	Lors de l'installation ou du remplacement de l'appareil, la mise � la terre doit toujours �tre connect�e en premier et d�connect�e en dernier.
Warnung	Der Erdanschlu� mu� bei der Installation oder beim Austauschen der Einheit immer zuerst hergestellt und zuletzt abgetrennt werden.
Avvertenza	In fase di installazione o sostituzione dell'unit�, eseguire sempre per primo il collegamento a massa e disconnetterlo per ultimo.
Advarsel	N�r enheten installeres eller byttes, m� jordledningen alltid tilkobles f�rst og frakobles sist.
Aviso	Ao instalar ou substituir a unidade, a liga��o � terra dever� ser sempre a primeira a ser ligada, e a �ltima a ser desligada.
�Advertencia!	Al instalar o sustituir el equipo, conecte siempre la toma de tierra al principio y descon�ctela al final.
Varning!	Vid installation eller utbyte av enheten m�ste jordledningen alltid anslutas f�rst och kopplas bort sist.





Aviso	Ao instalar ou substituir a unidade, a conex�o terra sempre deve ser executada primeiro e desconectada em seguida.
Advarsel	Ved installation og genmontering af enheden, skal jordforbindelsen altid installeres f�rst og afinstalleres sidst.

Statement 1072—Shock Hazard from Interconnections


Warning	Voltages that present a shock hazard may exist on Power over Ethernet (PoE) circuits if interconnections are made using uninsulated exposed metal contacts, conductors, or terminals. Avoid using such interconnection methods, unless the exposed metal parts are located within a restricted access location and users and service people who are authorized within the restricted access location are made aware of the hazard. A restricted access area can be accessed only through the use of a special tool, lock and key or other means of security.
Waarschuwing	Voltages kunnen elektrische schokken veroorzaken in PoE (Power over Ethernet)-circuits als er verbindingen worden gemaakt met blootliggende metalen contactpunten, geleiders of aansluitingspunten die niet zijn ge�soleerd. Gebruik dit type verbinding niet tenzij de blootliggende metalen onderdelen zich bevinden op een locatie met beperkte toegang en de gebruikers en onderhoudstechnici die toegang tot deze locatie hebben, op het gevaar worden gewezen. De locatie met beperkte toegang kan alleen worden geopend met speciaal gereedschap, slot en sleutel of een andere beveiligingsmethode.
Varoitus	Sis�isiss� Ethernet (PoE) -virtapiireiss� voi olla s�hk�iskun vaaran aiheuttavia j�nnitteit�, jos kytkent�ihin k�ytet��n erist�m�tt�mi� paljaita metalliliittimi� tai -johtimia. V�lt� t�llaisia kytkent�j�, elleiv�t paljaat metalliosat ole rajatussa paikassa. Ilmoita valtuutetuille k�ytt�jille ja huoltohenkil�ille vaarasta. Rajattuun alueeseen p��see k�siksi ainoastaan erityisty�kalua, lukkoa ja avainta tai muuta turvallista menetelm�� k�ytt�m�ll�.
Attention	Les tensions existant sur les alimentations utilisant la technologie PoE (Power over Ethernet) peuvent constituer un risque d'�lectrocution si les interconnexions sont effectu�es en utilisant des terminaux, conducteurs ou contacts m�talliques expos�s non isol�s. �vitez d'utiliser de telles m�thodes d'interconnexion � moins que les pi�ces m�talliques expos�es ne se trouvent dans un emplacement d'acc�s restreint et que les utilisateurs et les responsables du service autoris�s dans cet emplacement d'acc�s restreint ne soient conscients du danger. Une zone d'acc�s restreint peut �tre acc�d�e uniquement � l'aide d'une cl�, d'un outil et d'un verrou sp�cial, ou d'autres moyens de s�curit�.
Warnung	Bei Power-over-Ethernet-(PoE-)Schaltkreisen besteht u.U. Stromschlaggefahr, wenn Verbindungen unter Verwendung nicht isolierter, freiliegender Metallkontakte, Leiter oder Anschlussklemmen hergestellt werden. Vermeiden Sie das Herstellen solcher Verbindungen, es sei denn, die freiliegenden Metallteile befinden sich an Orten mit beschr�nktem Zugang, und Personen, die Zugang dazu haben, sind ausdr�cklich �ber diese Gefahr informiert worden. Ein Ort mit beschr�nktem Zugang ist nur mit Hilfe eines speziellen Werkzeugs, Schloss und Schl�ssels oder anderen Sicherheitseinrichtungen zug�nglich.
Avvertenza	Nei circuiti con alimentazione via Ethernet (PoE) possono verificarsi pericoli di scosse elettriche se si creano connessioni con contatti metallici, conduttori o terminali scoperti. Evitare di utilizzare i metodi di connessione sopraelencati a meno che le parti metalliche esposte non si trovino in una zona riservata e gli utenti e il personale di assistenza, che sono autorizzati ad accedere nella suddetta zona, siano stati messi al corrente del pericolo. � possibile accedere alla zona riservata solamente utilizzando gli appositi elementi di sicurezza.
Advarsel	I str�mkretser med PoE (Power over Ethernet) kan det v�re spenninger som kan utgj�re st�tfare hvis det blir foretatt sammenkoblinger med uisolerte, eksponerte kontakter, ledere eller terminaler av metall. Unng� � bruke slike sammenkoblingsmetoder med mindre de eksponerte metalldelene er i et omr�de med begrenset tilgang, og brukere og servicepersonell som har tilgang til det begrensede omr�det, blir gjort oppmerksom p� faren. Et omr�de med begrenset tilgang kan bare �pnes ved hjelp av spesialverkt�y, n�kkel eller andre sikkerhetstiltak.
Aviso	Pode haver voltagens que representam perigo de choque em circuitos PoE (Power over Ethernet) se as interconex�es forem feitas utilizando-se terminais, condutores ou contatos de metal exposto e sem isolamento. Evite utilizar tais m�todos de interconex�o a n�o ser que as partes de metal expostas estejam em um local de acesso restrito e os usu�rios e o pessoal de servi�o com acesso autorizado a este local restrito estejam cientes do perigo. Uma �rea de acesso restrito s� pode ser acessada com o uso de uma ferramenta, fechadura e chave especial ou de outros meios de seguran�a.
�Advertencia!	Puede haber voltajes con riesgo de shock en circuitos de alimentaci�n sobre el cableado Ethernet (PoE), si para las interconexiones se utilizan contactos, conductores o terminales met�licos descubiertos. Evite tales m�todos de interconexi�n, a menos que las partes met�licas descubiertas se encuentren en un lugar de acceso restringido y tanto los usuarios como el personal de servicios en dicho lugar sean conscientes de la existencia de tal riesgo. S�lo se puede tener acceso a una zona de acceso restringido mediante el uso de una herramienta especial, un candado y una llave u otros medios de seguridad.
Varning!	Det kan finnas sp�nningar p� PoE-kretsarna (Power over Ethernet) som utg�r risk f�r st�tar om sammankopplingarna g�rs med ej isolerade, exponerade kontakter, ledare och/eller terminaler av metall. Undvik att anv�nda s�dana sammankopplingsmetoder, s�vida inte de exponerade metalldelarna finns i en plats med begr�nsad �tkomst. Anv�ndare och servicepersonal som till�ts inom platsen med begr�nsad �tkomst m�ste vara medvetna om risken. Ett begr�nsat omr�de kan bara n�s med ett speciellt verktyg eller l�s, en speciell nyckel eller n�gon annan s�kerhetsmetod.

Statement 1073—No User-Serviceable Parts


Warning	No user-serviceable parts inside. Do not open. Statement 1073
Waarschuwing	Er zijn geen door de gebruiker te vervangen onderdelen. Niet openen.
Varoitus	Ei sis�ll� k�ytt�j�n huollettavissa olevia osia. �l� avaa.
Attention	Aucune pi�ce se trouvant � l'int�rieur ne peut �tre r�par�e ou remplac�e par l'utilisateur. Ne pas ouvrir.
Warnung	Enth�lt keine Teile, die vom Benutzer gewartet werden m�ssen. Bitte nicht �ffnen.
Avvertenza	Non contiene parti riparabili dall'utente. Non aprire.
Advarsel	Inneholder ingen deler som kan repareres av brukeren. M� ikke �pnes.
Aviso	Sem pe�as sujeitas a manuten��o pelo utilizador. N�o abrir.
�Advertencia!	No contiene partes que puedan ser arregladas por el usuario. No abrir.
Varning!	Det finns inga delar som anv�ndare kan utf�ra service p�. �ppna inte.





Aviso	Manuten��o somente por t�cnico especializado. N�o abra.
Advarsel	Ingen dele indeni som brugere kan reparere. �bn ej.

Statement 1074—Comply with Local and National Electrical Codes


Warning	Installation of the equipment must comply with local and national electrical codes.
Waarschuwing	Bij installatie van de apparatuur moet worden voldaan aan de lokale en nationale elektriciteitsvoorschriften.
Varoitus	Laitteisto tulee asentaa paikallisten ja kansallisten s�hk�m��r�ysten mukaisesti.
Attention	L'�quipement doit �tre install� conform�ment aux normes �lectriques nationales et locales.
Warnung	Die Installation der Ger�te muss den Sicherheitsstandards entsprechen.
Avvertenza	L'installazione dell'impianto deve essere conforme ai codici elettrici locali e nazionali.
Advarsel	Installasjon av utstyret m� samsvare med lokale og nasjonale elektrisitetsforskrifter.
Aviso	A instala��o do equipamento tem de estar em conformidade com os c�digos el�ctricos locais e nacionais.
�Advertencia!	La instalaci�n del equipo debe cumplir con las normativas de electricidad locales y nacionales.
Varning!	Installation av utrustningen m�ste ske i enlighet med g�llande elinstallationsf�reskrifter.

Statement 1079—Hot Surface


Warning	Hot surface. Statement 1079
Waarschuwing	Heet oppervlak.
Varoitus	Kuuma pinta.
Attention	Surface chaude.
Warnung	Hei�e Oberfl�che.
Avvertenza	Superficie molto calda.
Advarsel	Varm overflate.
Aviso	Superf�cie quente.
�Advertencia!	Superficie caliente.
Varning!	Het yta.


Warning	Hot surface. Statement 1079
Waarschuwing	Heet oppervlak.
Varoitus	Kuuma pinta.
Attention	Surface chaude.
Warnung	Hei�e Oberfl�che.
Avvertenza	Superficie molto calda.
Advarsel	Varm overflate.
Aviso	Superf�cie quente.
�Advertencia!	Superficie caliente.
Varning!	Het yta.

European Directives

Statement 275—Declaration of Conformity with Regard to the Directives 73/23/EEC and 89/336/EEC as amended by Directive 93/68/EEC


English:	This equipment is in compliance with the essential requirements and other provisions of Directives 73/23/EEC and 89/336/EEC as amended by Directive 93/68/EEC.
Dansk:	Dette udstyr er i overensstemmelse med de ufravigelige hensyn og andre bestemmelser i direktiv 73/23/EEC og 89/336/EEC som �ndred i direktiv 93/68/EEC.
Deutsch:	Dieses Ger�t entspricht den wesentlichen Anforderungen und weiteren Bestimmungen der Richtlinien 73/23/EWG und 89/336/EWG mit der Erg�nzung durch Richtlinie 93/68/EWG.
Espa�ol:	Este equipo cumple con los requisitos esenciales y otras disposiciones de las Directrices 73/23/EEC y 89/336/EEC de acuerdo a las modificaciones de la Directriz 93/68/EEC.

Fran�ais:	Cet appareil remplit les principales conditions requises et autres dispositions des Directives 73/23/EEC et 89/336/EEC, modifi�es par la Directive 93/68/EEC.
�slenska:	�essir b�na�ur samr�mist l�gbo�num kr�fum og ��rum �kv��um tilskipana 73/23/EBE og 89/336/EBE, me� breytingum skv. tilskipun 93/68/EBE.
Italiano:	Questa apparecchiatura � conforme ai requisiti essenziali e altre disposizioni delle Direttive 73/23/EEC e 89/336/EEC modificate con la Direttiva 93/68/EEC.
Nederlands:	Deze apparatuur voldoet aan de belangrijkste eisen en andere voorzieningen van richtlijnen 73/23/EEC en 89/336/EEC zoals gewijzigd door richtlijn 93/68/EEC.
Norsk:	Dette utstyret samsvarer med de vesentligste kravene og andre regler i direktivene 73/23/EEC og 89/336/EEC samt i tilleggsdirektiv 93/68/EEC.
Portugu�s:	Este equipamento satisfaz os requisitos essenciais e outras provis�es das Directivas 73/23/EEC e 89/336/EEC, conforme amendados pela Directiva 93/68/EEC.
	Catalyst 3560 switch
Suomalainen:	T�m� laite on direktiivien 73/23/ETY ja 89/336/ETY (kuten muutettu direktiiviss� 93/68/ETY) keskeisten vaatimusten ja m��r�ysten mukainen.
Svenska:	Denna utrustning uppfyller de v�sentliga kraven och andra villkor i direktiven 73/23/EEC och 89/336/EEC enligt �ndringarna i direktiv 93/68/EEC.

Regulatory Standards Compliance

This section includes all regulatory, safety, EMC, telecom, and NEBS standards. The Catalyst 3560 switch is in compliance with national and international standards as described in Table 1.

Table 1 Regulatory Standards Compliance for the Catalyst 3560 Switch
Specification	Description
Regulatory Compliance	Products with the CE Marking are compliant with the 89/336/EEC and 73/23/EEC directives, which include the safety and EMC standards listed.
Safety	UL/CSA 60950-1 EN 60950-1 IEC 60950-1 with all country deviations AS/NZ 60950-1
EMC	FCC Part 15 Class A EN55022 Class A (CISPR22) EN55024 (CISPR24) CE CNS13438 Class A AS/NZS CISPR22 Class A MIC China EMC requirements GOST

For specific details about the years, revisions and relevant amendments please refer to the applicable declaration of conformity available at http://tools.cisco.com/cse/prdapp/jsp/externalsearch.do?action=externalsearch&page=EXTERNAL_SEARCH&module=EXTERNAL_SEARCH.

EMC Environmental Conditions for Products Installed in the European Union

This section applies to products to be installed in the European Union.

The equipment is intended to operate under the following environmental conditions with respect to EMC:

•A separate defined location under user's control.

•Earthing and bonding shall meet the requirements of ETS 300 253 or CCITT K27.

•AC power distribution shall be one of the following types, where applicable: TN-S and TN-C as defined in IEC 364-3.

In addition, if equipment is operated in a domestic environment, interference may occur.

EMC Class A Notices and Warnings

This section includes the EMC Class A warnings for the Catalyst 3560 switch.

Class A Notice for FCC

Modifying the equipment without Cisco's authorization may result in the equipment no longer complying with FCC requirements for Class A digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television communications at your own expense.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case users will be required to correct the interference at their own expense.

Class A Notice for Canada

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil num�rique de la classe A est conforme � la norme NMB-003 du Canada.

Statement 340—Class A Warning for CISPR22


Warning	This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
Waarschuwing	Dit is een product van klasse A. In een woonomgeving kan dit product radiostoring veroorzaken. In dat geval moet de gebruiker de juiste maatregelen nemen.
Varoitus	T�m� on A-luokan tuote. Kotona k�ytettyn� t�m� tuote voi aiheuttaa radiotaajuush�iri�it�, jolloin k�ytt�j�n tulisi ryhty� vaadittaviin toimenpiteisiin h�iri�iden ehk�isemiseksi.
Attention	Il s'agit d'un produit de classe A. Dans un environnement local, ce produit peut entra�ner des perturbations radio�lectriques, auquel cas l'utilisateur devra �ventuellement prendre des mesures ad�quates.
Warnung	Dies ist ein Produkt der Klasse A. Bei der Verwendung dieses Produkts im Haus- oder Wohnungsbereich kann es zu Funkst�rungen kommen. In diesem Fall muss der Benutzer u. U. angemessene Ma�nahmen ergreifen.
Avvertenza	Prodotto di classe A. � possibile che il prodotto generi interferenze radio in un ambienti chiusi. In questo caso l'utente deve intraprendere le misure adeguate per risolvere il problema.
Advarsel	Dette er et produkt i klasse A. I et hjemmemilj� kan dette produktet for�rsake radioforstyrrelser, og brukeren kan da v�re n�dt til � ta de n�dvendige forholdsregler.
Aviso	Este � um produto de classe A. Em um ambiente dom�stico, este produto pode causar interfer�ncia de r�dio. Nesse caso, talvez o usu�rio precise tomar as medidas adequadas.
�Advertencia!	Este es un producto de clase A. En el �mbito dom�stico, este producto puede causar radiointerferencias, lo que puede hacer necesaria la puesta en marcha de medidas adecuadas.
Varning!	Detta �r en klass A-produkt. Denna produkt kan orsaka radiost�rningar inomhus. Det kan d� vara ett krav att anv�ndaren vidtar l�mpliga �tg�rder.

Statement 191—VCCI Class A Warning for Japan


Warning	This is a Class A product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be required to take corrective actions.

Statement 256—Class A Warning for Hungary


Warning	This equipment is a class A product and should be used and installed properly according to the Hungarian EMC Class A requirements (MSZEN55022). Class A equipment is designed for typical commercial establishments for which special conditions of installation and protection distance are used.

Statement 294—Class A Warning for Korea


Warning	This is a Class A Device and is registered for EMC requirements for industrial use. The seller or buyer should be aware of this. If this type was sold or purchased by mistake, it should be replaced with a residential-use type.

Statement 371—Power Cable and AC Adapter

Obtaining Documentation

Cisco documentation and additional literature are available on Cisco.com. This section explains the product documentation resources that Cisco offers.

Cisco.com

You can access the most current Cisco documentation at this URL:

http://www.cisco.com/techsupport

You can access the Cisco website at this URL:

http://www.cisco.com

You can access international Cisco websites at this URL:

http://www.cisco.com/public/countries_languages.shtml

Product Documentation DVD

The Product Documentation DVD is a library of technical product documentation on a portable medium. The DVD enables you to access installation, configuration, and command guides for Cisco hardware and software products. With the DVD, you have access to the HTML documentation and some of the PDF files found on the Cisco website at this URL:

http://www.cisco.com/univercd/home/home.htm

The Product Documentation DVD is created and released regularly. DVDs are available singly or by subscription. Registered Cisco.com users can order a Product Documentation DVD (product number DOC-DOCDVD= or DOC-DOCDVD=SUB) from Cisco Marketplace at the Product Documentation Store at this URL:

http://www.cisco.com/go/marketplace/docstore

Ordering Documentation

You must be a registered Cisco.com user to access Cisco Marketplace. Registered users may order Cisco documentation at the Product Documentation Store at this URL:

http://www.cisco.com/go/marketplace/docstore

If you do not have a user ID or password, you can register at this URL:

http://tools.cisco.com/RPF/register/register.do

Documentation Feedback

You can provide feedback about Cisco technical documentation on the Cisco Technical Support & Documentation site area by entering your comments in the feedback form available in every online document.

Cisco Product Security Overview

Cisco provides a free online Security Vulnerability Policy portal at this URL:

http://www.cisco.com/en/US/products/products_security_vulnerability_policy.html

From this site, you will find information about how to do the following:

•Report security vulnerabilities in Cisco products

•Obtain assistance with security incidents that involve Cisco products

•Register to receive security information from Cisco

A current list of security advisories, security notices, and security responses for Cisco products is available at this URL:

http://www.cisco.com/go/psirt

To see security advisories, security notices, and security responses as they are updated in real time, you can subscribe to the Product Security Incident Response Team Really Simple Syndication (PSIRT RSS) feed. Information about how to subscribe to the PSIRT RSS feed is found at this URL:

http://www.cisco.com/en/US/products/products_psirt_rss_feed.html

Reporting Security Problems in Cisco Products

Cisco is committed to delivering secure products. We test our products internally before we release them, and we strive to correct all vulnerabilities quickly. If you think that you have identified a vulnerability in a Cisco product, contact PSIRT:

•For emergencies only — security-alert@cisco.com

An emergency is either a condition in which a system is under active attack or a condition for which a severe and urgent security vulnerability should be reported. All other conditions are considered nonemergencies.

•For nonemergencies — psirt@cisco.com

In an emergency, you can also reach PSIRT by telephone:

•1 877 228-7302

•1 408 525-6532

Tip We encourage you to use Pretty Good Privacy (PGP) or a compatible product (for example, GnuPG) to encrypt any sensitive information that you send to Cisco. PSIRT can work with information that has been encrypted with PGP versions 2.x through 9.x.

Never use a revoked encryption key or an expired encryption key. The correct public key to use in your correspondence with PSIRT is the one linked in the Contact Summary section of the Security Vulnerability Policy page at this URL:

http://www.cisco.com/en/US/products/products_security_vulnerability_policy.html

The link on this page has the current PGP key ID in use.

If you do not have or use PGP, contact PSIRT to find other means of encrypting the data before sending any sensitive material.

Product Alerts and Field Notices

Modifications to or updates about Cisco products are announced in Cisco Product Alerts and Cisco Field Notices. You can receive Cisco Product Alerts and Cisco Field Notices by using the Product Alert Tool on Cisco.com. This tool enables you to create a profile and choose those products for which you want to receive information.

To access the Product Alert Tool, you must be a registered Cisco.com user. (To register as a Cisco.com user, go to this URL: http://tools.cisco.com/RPF/register/register.do) Registered users can access the tool at this URL: http://tools.cisco.com/Support/PAT/do/ViewMyProfiles.do?local=en

Obtaining Technical Assistance

Cisco Technical Support provides 24-hour-a-day award-winning technical assistance. The Cisco Technical Support & Documentation website on Cisco.com features extensive online support resources. In addition, if you have a valid Cisco service contract, Cisco Technical Assistance Center (TAC) engineers provide telephone support. If you do not have a valid Cisco service contract, contact your reseller.

Cisco Technical Support & Documentation Website

The Cisco Technical Support & Documentation website provides online documents and tools for troubleshooting and resolving technical issues with Cisco products and technologies. The website is available 24 hours a day at this URL:

http://www.cisco.com/techsupport

Access to all tools on the Cisco Technical Support & Documentation website requires a Cisco.com user ID and password. If you have a valid service contract but do not have a user ID or password, you can register at this URL:

http://tools.cisco.com/RPF/register/register.do

Note Use the Cisco Product Identification Tool to locate your product serial number before submitting a request for service online or by phone. You can access this tool from the Cisco Technical Support & Documentation website by clicking the Tools & Resources link, clicking the All Tools (A-Z) tab, and then choosing Cisco Product Identification Tool from the alphabetical list. This tool offers three search options: by product ID or model name; by tree view; or, for certain products, by copying and pasting show command output. Search results show an illustration of your product with the serial number label location highlighted. Locate the serial number label on your product and record the information before placing a service call.

Tip Displaying and Searching on Cisco.com

If you suspect that the browser is not refreshing a web page, force the browser to update the web page by holding down the Ctrl key while pressing F5.

To find technical information, narrow your search to look in technical documentation, not the entire Cisco.com website. On the Cisco.com home page, click the Advanced Search link under the Search box and then click the Technical Support & Documentation radio button.

To provide feedback about the Cisco.com website or a particular technical document, click Contacts & Feedback at the top of any Cisco.com web page.

Submitting a Service Request

Using the online TAC Service Request Tool is the fastest way to open S3 and S4 service requests. (S3 and S4 service requests are those in which your network is minimally impaired or for which you require product information.) After you describe your situation, the TAC Service Request Tool provides recommended solutions. If your issue is not resolved using the recommended resources, your service request is assigned to a Cisco engineer. The TAC Service Request Tool is located at this URL:

http://www.cisco.com/techsupport/servicerequest

For S1 or S2 service requests, or if you do not have Internet access, contact the Cisco TAC by telephone. (S1 or S2 service requests are those in which your production network is down or severely degraded.) Cisco engineers are assigned immediately to S1 and S2 service requests to help keep your business operations running smoothly.

To open a service request by telephone, use one of the following numbers:

Asia-Pacific: +61 2 8446 7411
Australia: 1 800 805 227
EMEA: +32 2 704 55 55
USA: 1 800 553 2447

For a complete list of Cisco TAC contacts, go to this URL:

http://www.cisco.com/techsupport/contacts

Definitions of Service Request Severity

To ensure that all service requests are reported in a standard format, Cisco has established severity definitions.

Severity 1 (S1)—An existing network is "down" or there is a critical impact to your business operations. You and Cisco will commit all necessary resources around the clock to resolve the situation.

Severity 2 (S2)—Operation of an existing network is severely degraded, or significant aspects of your business operations are negatively affected by inadequate performance of Cisco products. You and Cisco will commit full-time resources during normal business hours to resolve the situation.

Severity 3 (S3)—Operational performance of the network is impaired while most business operations remain functional. You and Cisco will commit resources during normal business hours to restore service to satisfactory levels.

Severity 4 (S4)—You require information or assistance with Cisco product capabilities, installation, or configuration. There is little or no effect on your business operations.

Obtaining Additional Publications and Information

Information about Cisco products, technologies, and network solutions is available from various online and printed sources.

•The Cisco Online Subscription Center is the website where you can sign up for a variety of Cisco e-mail newsletters and other communications. Create a profile and then select the subscriptions that you would like to receive. To visit the Cisco Online Subscription Center, go to this URL:

http://www.cisco.com/offer/subscribe

•The Cisco Product Quick Reference Guide is a handy, compact reference tool that includes brief product overviews, key features, sample part numbers, and abbreviated technical specifications for many Cisco products that are sold through channel partners. It is updated twice a year and includes the latest Cisco channel product offerings. To order and find out more about the Cisco Product Quick Reference Guide, go to this URL:

http://www.cisco.com/go/guide

•Cisco Marketplace provides a variety of Cisco books, reference guides, documentation, and logo merchandise. Visit Cisco Marketplace, the company store, at this URL:

http://www.cisco.com/go/marketplace/

•Cisco Press publishes a wide range of general networking, training, and certification titles. Both new and experienced users will benefit from these publications. For current Cisco Press titles and other information, go to Cisco Press at this URL:

http://www.ciscopress.com

•Internet Protocol Journal is a quarterly journal published by Cisco Systems for engineering professionals involved in designing, developing, and operating public and private internets and intranets. You can access the Internet Protocol Journal at this URL:

http://www.cisco.com/ipj

•Networking products offered by Cisco Systems, as well as customer support services, can be obtained at this URL:

http://www.cisco.com/en/US/products/index.html

•Networking Professionals Connection is an interactive website where networking professionals share questions, suggestions, and information about networking products and technologies with Cisco experts and other networking professionals. Join a discussion at this URL:

http://www.cisco.com/discuss/networking

•"What's New in Cisco Documentation" is an online publication that provides information about the latest documentation releases for Cisco products. Updated monthly, this online publication is organized by product category to direct you quickly to the documentation for your products. You can view the latest release of "What's New in Cisco Documentation" at this URL:

http://www.cisco.com/univercd/cc/td/doc/abtunicd/136957.htm

•World-class networking training is available from Cisco. You can view current offerings at this URL:

http://www.cisco.com/en/US/learning/index.html

This document is to be used in conjunction with the documents listed in the "Related Documentation" section.

CCVP, the Cisco Logo, and the Cisco Square Bridge logo are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn is a service mark of Cisco Systems, Inc.; and Access Registrar, Aironet, BPX, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Enterprise/Solver, EtherChannel, EtherFast, EtherSwitch, Fast Step, Follow Me Browsing, FormShare, GigaDrive, GigaStack, HomeLink, Internet Quotient, IOS, IP/TV, iQ Expertise, the iQ logo, iQ Net Readiness Scorecard, iQuick Study, LightStream, Linksys, MeetingPlace, MGX, Networking Academy, Network Registrar, Packet, PIX, ProConnect, RateMUX, ScriptShare, SlideCast, SMARTnet, StackWise, The Fastest Way to Increase Your Internet Quotient, and TransPath are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.

All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0609R)

Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental.

Printed in China PRC

Table Of Contents