cc/td/doc/product/lan/cat2950/12122ea2
hometocprevnextglossaryfeedbacksearchhelp
PDF

Table Of Contents

Overview

Features

Front-Panel Description

Warning Labels

10/100 Ports

10/100/1000 Ports

100BASE-FX Ports

100BASE-LX Ports

Power and Relay Connector

Console Port

LEDs

Rear-Panel Description

Catalyst 2955 Switch Power Converter

Management Options


Overview


This chapter provides these topics that describe the Catalyst 2955 switch, hereafter referred to as the switch.

Features

Front-Panel Description

Rear-Panel Description

Catalyst 2955 Switch Power Converter

Features

The Catalyst 2955 switch is a member of the Catalyst 2950 switch family. Catalyst switches are a series of Ethernet switches that you can use to connect any Ethernet-enabled devices.

The Catalyst 2955 switch is an Ethernet switch that mounts on a DIN rail in an industrial enclosure as well as in a standard 19-inch rack. Its components are designed to withstand extremes in temperature, vibration, and shock so that the switch can be deployed in an industrial environment.


Note The Catalyst 2955 switch does not have cooling fans


See the switch software configuration guide for examples that show how you might deploy the switches in your network.

Figure 2-1 through Figure 2-3 show the Catalyst 2955 switches.

These are the switch features:

Hardware

Catalyst 2955T-12 switch—12 10/100 ports and 2 10/100/1000BASE-T ports

Catalyst 2955C-12 switch—12 10/100 ports and 2 multimode (MM) 100BASE-FX ports

Catalyst 2955S-12 switch—12 10/100 ports and 2 single-mode (SM) 100BASE-LX ports

Configuration

For 10/100BASE-TX ports, autonegotiates the speed and duplex settings

For 10/100/1000 BASE-T uplink ports, autonegotiates the speed and supports half- and full-duplex operation at 10/100 Mbps and full-duplex operation at 1000 Mbps

For 100BASE-FX multimode fiber-optic MM uplink ports, supports only 100-Mbps and full-duplex settings

For 100BASE-LX single-mode fiber-optic SM uplink ports, supports only100-Mbps and full-duplex settings

Front-Panel Description

The switch front panel contains the ports, the LEDs, and the power and relay cable connector.

Figure 2-1 to Figure 2-3 show the switch front panels.

Figure 2-1 Catalyst 2955T-12 Switch

1

10/100/1000 uplink ports

4

10/100 ports

2

Functional ground screw

5

LEDs

3

Power and relay connector

   

Figure 2-2 Catalyst 2955C-12 Switch

1

100BASE-FX uplink ports

4

10/100 ports

2

Functional ground screw

5

LEDs

3

Power and relay connector

   

Figure 2-3 Catalyst 2955S-12 Switch

1

100BASE-LX uplink ports

4

10/100 ports

2

Functional ground lug

5

LEDs

3

Power and relay connector

   

Warning Labels

The laser safety warning label (as shown in Figure 2-4) is on the Catalyst 2955C-12 and 2955S-12 switch front panels. The MM fiber-optic ports on the Catalyst 2955C-12 are Class 1 LEDs. The SM fiber-optic uplink ports on the Catalyst 2955S-12 are Class 1 laser products.

The laser safety warning label means that you should be careful when working with fiber-optic ports and cabling. See Appendix C, "Translated Safety Warnings" for more information about laser safety guidelines.

Figure 2-4 Laser Safety Warning Label

The hot surface warning label (shown in Figure 2-5) is on the Catalyst 2955C-12, 2955S-12, and 2955T-12 switch front panels. This label means that the surface of the switch is hot. See Appendix C, "Translated Safety Warnings," for more information about proper handling guidelines for hot surfaces.

Figure 2-5 Hot Surface Warning Label

10/100 Ports

The 10/100 ports use RJ-45 connectors and twisted-pair cabling. The ports can connect to these devices:

10BASE-T devices, such as workstations and hubs, through standard RJ-45 connectors and two twisted-pair cabling. You can use Category 3, 4, or 5 cabling.

100BASE-TX devices, such as high-speed workstations, servers, hubs, routers, and other switches, through standard RJ-45 connectors and two or four twisted-pair, Category 5 cabling.


Note When connecting the switch to workstations, servers, and routers, be sure that the cable is a twisted-pair straight-through cable. When connecting the switch to hubs or other switches, use a twisted-pair crossover cable. Pinouts for the cables are described in Appendix B, "Connectors and Cables."


The 10/100 ports can be set to operate in any combination of half duplex, full duplex, 10 Mbps, or 100 Mbps. They can also be set for speed and duplex autonegotiation, compliant with IEEE 802.3U. In all cases, the cable length from a switch to an attached device cannot exceed 328 feet (100 meters).

When set for autonegotiation, a port senses the speed and duplex settings of the attached device and advertises its own capabilities. If the attached device supports autonegotiation, the port negotiates the best connection (that is, the fastest line speed that both devices support and full-duplex transmission, if the attached device supports it) and configures itself accordingly.

10/100/1000 Ports

The 10/100/1000 uplink ports on the Catalyst 2955T-12 switch use RJ-45 connectors and twisted-pair cabling. The ports can connect to these devices:

10BASE-T devices, such as workstations and hubs, through standard RJ-45 connectors and two or four twisted-pair, Category 3, 4, or 5 cabling.

100BASE-TX devices, such as high-speed workstations, servers, hubs, routers, and other switches, through standard RJ-45 connectors and two or four twisted-pair, Category 5 cabling.

1000BASE-T devices, such as high-speed workstations, servers, hubs, routers, and other switches, through standard RJ-45 connectors and four twisted-pair, Category 5 cabling.


Note When connecting the switch to a 1000BASE-T device, be sure to use a four twisted-pair, Category 5 cable.



Note When connecting the switch to workstations, servers, and routers, be sure to use a twisted-pair straight-through cable. When connecting the switch to hubs or other switches, use a twisted-pair crossover cable. Pinouts for the cables are described in Appendix B, "Connectors and Cables."


The 10/100/1000 ports on the Catalyst 2955T-12 switch can be set to operate at 10 or 100 Mbps at half- or full-duplex mode or 1000 Mbps in full-duplex mode. They can also be set for speed autonegotiation, compliant with IEEE 802.3ab. In all cases, the cable length from a switch to an attached device cannot exceed 328 feet (100 meters).

100BASE-FX Ports

The 100BASE-FX ports on the Catalyst 2955C-12 use 50/125- or 62.5/125-micron MM fiber-optic cabling. In full-duplex mode, the MM fiber-optic cable length from a switch to an attached device cannot exceed 6562 feet (2 kilometers).

For MM connections, you can connect a 100BASE-FX port to a port on a target device by using one of the MT-RJ fiber-optic patch cables listed in Table B-1 on page B-3. Use the Cisco part numbers in Table B-1 to order the patch cables that you need.

100BASE-LX Ports

The 100BASE-LX ports on the Catalyst 2955S-12 use 9/125-micron SM fiber-optic cabling. The cable length from a switch to an attached device cannot exceed 9.375 miles (15 kilometers).

For SM connections, use one of the connectors listed in Table B-2 on page B-4. Use the Cisco part numbers in Table B-2 to order the connectors that you need.

Power and Relay Connector

The power and relay connector provides wire connections to the switch for DC power and configurable alarms (see Figure 2-6). The power and relay connector is to the right of the uplink ports on the faceplate.

Figure 2-6 Power and Relay Connector

The connector is a pluggable-screw terminal block connector that provides power and return connections for both the primary and secondary power supplies. The positive DC power connection for power supply A is labeled VA, and the return for power supply A is the adjacent connection labeled RT. For power supply B (the redundant power supply), the positive DC power connection is labeled VB, and the return is the adjacent connection labeled RT.

The Catalyst 2955 switch can operate with a single power supply or with dual power supplies. In dual-power mode, the switch draws power from the power supply with higher voltage. If the primary power supply fails in dual-power mode, the alternate power supply gives power to the switch.


Warning When you connect or disconnect the power and relay connector with power applied, an electrical arc can occur. This could cause an explosion in hazardous area installations. Be sure that power is removed from the switch and alarm circuit. Be sure that power cannot be accidentally turned on or verify that the area is nonhazardous before proceeding.

Failure to securely tighten the power and relay connector captive screws can result in an electrical arc if the connector is accidentally removed. Statement 1058


The power and relay connector provides an interface for two independent, normally open (NO) alarm relays. The relays can be triggered by alarms for environmental, power supply, and port status conditions. The relays can be configured to send a fault signal to an external alarm device, such as a bell or a light indicator. You can use the CLI to associate any alarm condition with a single alarm relay or with both relays.

To connect an external alarm device to the relay, you must connect two relay contact wires to complete an electrical circuit. Because each external alarm device requires two connections to a relay, the Catalyst 2955 switch supports a maximum of two external alarm devices.


Note See the switch configuration guide for instructions on how to configure the alarm relays.


For more information about the power and relay connector, see Appendix B, "Connectors and Cables."


Note You can get replacement power and relay connectors (PWR-2955-CONNECT=) by calling Cisco Technical Support. See the "Obtaining Technical Assistance" section on page xxviii.


Console Port

You can connect a switch to a PC through the console port and the supplied RJ-45-to-DB-9 adapter cable. If you want to connect a switch to a terminal, you need to provide an RJ-45-to-DB-25 female DTE adapter. You can order a kit (part number ACS-DSBUASYN=) with that adapter from Cisco Systems. For console-port and adapter-pinout information, see the "Cable and Adapter Specifications" section on page B-5.


Warning If you connect or disconnect the console cable with power applied to the switch or any device on the network, an electrical arc can occur. This could cause an explosion in hazardous location installations. Be sure that power is removed or the area is nonhazardous before proceeding.

To verify switch operation, perform POST on the switch in a nonhazardous location before installation.Statement 1065


LEDs

You can use the LEDs to monitor switch activity and performance. The LEDs on all Catalyst 2955 switches are on the bottom edge of the front panel. The LEDs are visible in both face-up and parallel mounting configurations, as shown in Figure 2-7 and Figure 2-8.


Note The 10/100 port status LEDs show port status only.


All LEDs are visible through the GUI management applications—the Network Assistant application for multiple switches and the device manager GUI for a single switch. The switch software configuration guide describes how to use the CLI to configure and to monitor individual switches and switch clusters.

Figure 2-7 LEDs on the Catalyst 2955T-12 Switch

1

10/100 port status LEDs

3

Alarm relay LEDs

2

Uplink port status LEDs

4

Power supply LEDs


Figure 2-8 LEDs on Catalyst 2955C-12 and Catalyst 2955S-12 Switches

1

10/100 port status LEDs

3

Alarm relay LEDs

2

Uplink port status LEDs

4

Power supply LEDs


Power Status LEDs

The Catalyst 2955 switch can operate with one or two power supplies. Each power supply input has an associated LED that shows the power supply status.

If the switch is in single-power mode and only power supply A is present and functioning, the LED for power supply B is green, and the LED for power supply A shows its status.

If the switch is in single-power mode and only power supply B is present and functioning, the LED for power supply A is green, and the LED for power supply B shows its status.

In dual-power mode, the switch draws power from the power supply with the higher voltage. If the primary power supply fails in dual-power mode, the alternate power supply gives power to the switch.

The power status LEDs show whether the individual power supplies are receiving power and functioning properly.

Table 2-1 lists the LED colors and meanings.


Note The power status LEDs show that power is not present on the switch if the power input drops below 17 V. The power status LEDs only show that power is present if the voltage at the switch input exceeds 18.5 V. The 1.5 V difference, or hysteresis, ensures that the power status LEDs do not oscillate at values near 18 V.

In dual-power mode, the power status LEDs show status for both power inputs, VA and VB.


Table 2-1 Power Status LEDs 

Color
System Status

Off

System is not powered up.

Green

Power present on associated contact.

Red

Power not present on associated contact.


For information about the power LED colors during the power-on self-test (POST), see the "Powering On the Switch and Running POST" section on page 3-13.

10/100 Port Status LEDs

Each 10/100 port has a port status LED, also called a port LED, shown in Figure 2-7 and Figure 2-8. These LEDs display information about the switch and the individual ports, shown in Table 2-2.

Table 2-2 10/100 Port Status LEDs 

Color
System Status

Off

No link.

Solid green

Link present.

Flashing green

Activity. Port is transmitting or receiving data.

Alternating green-amber

Link fault. Error frames can affect connectivity, and errors such as excessive collisions, CRC errors, and alignment and jabber errors are monitored for a link-fault indication.

Solid amber

Port is not forwarding. Port was disabled by management, an address violation, or Spanning Tree Protocol (STP).

Note After a port is reconfigured, the port LED can remain amber for up to 30 seconds while STP checks the switch for possible loops.


Uplink Port Status LEDs

The Catalyst 2955 switch has two uplink port status LEDs to the right of the port status LEDs. On the Catalyst 2955C-12 and 2955S-12 switches, the fiber-optic uplink port status LEDs are labeled 13 and 14 (see Figure 2-8). On the Catalyst 2955T-12, the 10/100/1000BASE-T uplink ports are labeled 1 and 2 (see Figure 2-7).

These LEDs display information about the switch and the individual uplink ports, as shown in Table 2-3, Table 2-4, and Table 2-5.


Note The uplink port status LEDs provide system and status information during POST. See the "Powering On the Switch and Running POST" section on page 3-13 for more information about uplink port LED colors during POST.


Table 2-3 10/100/1000BASE-T Uplink Port Status LEDs 

Color
System Status

Off

No link.

Solid green

Link is present.

Flashing green

Activity. Port is transmitting or receiving data.

Alternating green-amber

Link is faulty.

Solid amber

Link is disabled.


Table 2-4 100BASE-FX MM Uplink Port Status LEDs 

Color
System Status

Off

No link.

Solid green

Link is present.

Flashing green

Activity. Port is transmitting or receiving data.

Alternating green-amber

Link is faulty.

Solid amber

Link is disabled.


Table 2-5 100BASE-LX SM Uplink Port Status LEDs 

Color
System Status

Off

No link.

Solid green

Link is present.

Flashing green

Activity. Port is transmitting or receiving data.

Alternating green-amber

Link is faulty.

Solid amber

Link is disabled.


Alarm Relay LEDs

Two alarm relay LEDs labeled MAJ and MIN are to the right of the uplink port status LEDs, as shown in Figure 2-7 and Figure 2-8. These LEDs reflect the state of the major and minor system alarms.

You can use the Cisco IOS command-line interface (CLI) to configure the major and minor LEDs to drive the relay contacts so that the connected external alarm device state mirrors the alarm state of the major (MAJ) or minor (MIN) LED. You can also use the CLI to associate port and global status alarms to one or both relays. See the switch software configuration guide for details.


Warning The switch relays are rated at 1 Amp and have a voltage limit of 30 VDC and 0.3 Amp at a voltage limit of 125 VAC. It is dangerous to exceed these limitations in a hazardous environment.

An electrical arc can occur when you connect or disconnect the relay wires with field side power applied. This could cause an explosion in switch installations in a hazardous location. Before proceeding, be sure that power is removed or the area is not hazardous. Statement 1061.


Table 2-6 lists the LED colors and meanings.

Table 2-6 Alarm and Relay LEDs 

LED
Color
Meaning

Major relay (MAJ)

Off

Environmental temperature is within normal range, or connected alarm is not in a state of fault.

Red

Environmental temperature exceeds maximum threshold, or connected alarm is in a state of fault.

Minor relay (MIN)

Off

Connected alarm is not in a state of fault.

Red

Connected alarm is in a state of fault.



Note The minor LED is disabled by default.


Rear-Panel Description

The rear panel of the Catalyst 2955 switch has a DIN rail mounting clip assembly, as shown in Figure 2-9.

The switch ships with the clip assembly installed on the rear panel, for a parallel mounting configuration.

Figure 2-9 Catalyst 2955 Switch Rear Panel

1

Catalyst 2955 switch rear panel

3

DIN rail clip mounting screws

2

DIN rail clip assembly

   

Catalyst 2955 Switch Power Converter

The Catalyst 2955 switch can be used with an optional AC/DC power converter in a nonhazardous environment. The power converter (PWR-2955-AC=) can supply 24 VDC power in three modes—110 V nominal AC, 220 V nominal AC, and up to 375 VDC (see Table 3-2)—to one or two Catalyst 2955 switches. The power converter is mounted on a DIN rail.

For installation and connection procedures for the power converter, see the "Connecting the Switch to the Power Converter" section on page 3-29.


Caution The power converter should only be used in a nonhazardous location installation.


Note The power converter (PWR-2955-AC=) is sold separately.


Figure 10 shows the power converter.

Figure 10 The Catalyst 2955 Switch AC/DC Power Converter

1

DC positive connections

4

AC line connection

2

DC return connections

5

AC neutral connection

3

Earth ground connection

   

Management Options

Catalyst 2955 switches offer these management options:

Network Assistant

Cisco Network Assistant is a PC-based network management GUI application optimized for LANs of small and medium-sized businesses. Cisco Network Assistant offers centralized management of Cisco switches ranging from the Catalyst 2950 switch to the Catalyst 4506 switch. Through a user-friendly GUI, users can configure and manage switch clusters or standalone switches. Cisco Network Assistant is available at no cost and can be downloaded from this URL:

http://www.cisco.com/go/networkassistant

For information on starting the Network Assistant application, see the Getting Started with Cisco Network Assistant guide on Cisco.com.

Device manager

You can use the device manager, which is in the switch memory, to manage individual and standalone switches. Device manager is an easy-to-use web interface that offers quick configuration and monitoring. You can access the device manager from anywhere in your network through a web browser. For more information, see the device manager online help.

Cisco IOS command-line interface (CLI)

You can manage switches by using command-line entries. To access the CLI, connect a PC or terminal directly to the console port on the switch. If the switch is attached to your network, you can use a Telnet connection to manage the switch from a remote location. For more information, see the switch command reference.

CiscoView application

You can use the CiscoView device-management application to set configuration parameters and to view switch status and performance information. This application, which you purchase separately, can be a standalone application or part of an Simple Network Management Protocol (SNMP) network-management platform. For more information, see the documentation that came with your CiscoView application.

SNMP network management

You can manage switches by using an SNMP-compatible management station running platforms such as HP OpenView and SunNet Manager. The switch supports a comprehensive set of MIB extensions and MIB II, the IEEE 802.1D bridge MIB, and four Remote Monitoring (RMON) groups. For more information, see the documentation that came with your SNMP application.

Cisco Intelligence Engine 2100 (IE2100)

The Cisco IE200 Series Configuration Registrar is a network management device that works with embedded Cisco Networking Services (CNS) agents in the switch software. You can automate initial configurations and configuration updates by generating switch-specific configuration changes, sending them to the switch, executing the configuration change, and logging the results. For more information, see the switch software configuration guide and the documentation that came with your application.


hometocprevnextglossaryfeedbacksearchhelp

Posted: Mon Nov 15 05:37:20 PST 2004
All contents are Copyright © 1992--2004 Cisco Systems, Inc. All rights reserved.
Important Notices and Privacy Statement.