|
These release notes describe new features and resolved and open issues for the Cisco Broadband Operating System (CBOS) Release 2.4.3b. Please refer to previous release notes for specific information concerning past releases.
For more detailed information about the information in these release notes, refer to the "Obtaining Documentation" section. Information about electronic documentation can be found in the "Cisco.com" section.
These release notes provide the following information:
Cisco Broadband Operating System Release 2.4.3.b
Resolved Issues in CBOS Release 2.4.3.b
Known Issues in CBOS Release 2.4.3.b
Obtaining Technical Assistance
Use these release notes in conjunction with these documents:
Note There is important information in the Cisco Broadband Operating System 2.4.3 Release Notes that also applies to this release. |
This release of CBOS 2.4.3.b contains a fix for DSL modems which connect to a digital off-hook (DOH) DSLAM and do not have DOH enabled.
The Cisco Commander software must not be running when you install CBOS 2.4.3.b.
This software starts out with the web server disabled (IP Socket 80 is closed). If you need the CPE web server enabled, you must change this setting in the configuration after the upgrade is completed.
TFTP server functionality is disabled by default on the CPE. If you have not manually enabled it, you must know your enable and exec passwords to install this software.
Caution Do not change anything else while making these changes; doing so can cause loss of connectivity or data. |
The following is the list of images that can be downloaded to the CPE.
Note You must use the image specific to your CPE device. If you try to use an image for a different device, you will be unable to connect to your service provider. |
To find the image that a 677 or 678 CPE is running, from the CBOS command line, enter:
show versionFor more information on upgrading please see the Release Notes for the previous releases of CBOS, and the following URL:
http://www.cisco.com/cgi-bin/tablebuild.pl/600-v242?param=case3
With CBOS 2.4.3.b, the VIP network has its own Outside Global IP address. Traffic sourced from the VIP Outside network to the Inside network requires a static NAT entry specifying the VIP Outside Global IP address.
Note The VIP configuration of public or private addresses behind a 600 series CPE still limits the user to the one outside NAT address for WAN access. |
To set a VIP network to Outside, add the following command:
set int vipx outsidewhere x is a value ranging from 0 to 2.
To set the VIP Outside Global IP address add the following command:
set interface vipx ip addressTo allow traffic from the VIP Outside network to access the Inside network, add the following command:
set nat entry add inside_IP_address inside_port VIP_Outside_IP Outside_port protocolThe following is an example configuration for a CPE 675:
675-rc4#show config
[[ CBOS = Section Start ]]
NSOS Prompt = 675-rc4
NSOS 1483 Routing = enabled
NSOS MD5 Enable Password =
C64100007F160000812700006C44000046D96F11BD49778827656
8D7C2CDE806
NSOS MD5 Root Password =
8D030000215900000028000073320000F0247C9D8312335A0F18738
AB2509E97
NSOS MD5 Commander Password = E7061E2A3FC26E5E101400453E424DFC
NSOS Virtual IP Address = 00, 33.1.1.1
NSOS Virtual IP Address = 01, 44.1.1.1
[[ IP Routing = Section Start ]]
IP Port Address = 00, 11.1.1.1
IP NAT Outside IP = 22.1.1.1
IP NAT = enabled
IP NAT VIP Port Side = 01, inside
IP NAT Entry = 44.1.1.2, 69, 31.1.1.1, 69, udp;11.1.1.2, 23, 21.1.1.1, 23,
tcp;
[[ DHCP = Section Start ]]
DHCP Server Pool IP = 00, 11.1.1.2
DHCP Server Pool Gateway = 00, 11.1.1.1
DHCP Server Pool DNS = 00, 171.71.193.20
[[ TFTP = Section Start ]]
TFTP = enabled
675-rc4#show nat
NAT is currently enabled
Port Network Global
eth0 Inside
wan0-0 Outside 22.1.1.1
vip0 Outside 33.1.1.1
vip1 Inside
vip2 Outside
Local IP : Port Global IP : Port Timer Flags Proto
Interface
11.1.1.2:23 21.1.1.1:23 0 0x00041 tcp eth0
44.1.1.2:69 31.1.1.1:69 0 0x00041 udp vip1
675-rc4#show int
IP Address Mask
eth0 11.1.1.1 255.255.255.0
vip0 33.1.1.1 255.255.255.0
vip1 44.1.1.1 255.255.255.0
vip2 0.0.0.0 255.255.255.0
wan0 Physical Port: Trained
Dest IP Address Mask
wan0-0 0.0.0.0 255.255.255.255
The following issues can be resolved by installing Release 2.4.3.b of CBOS.
This section lists open issues for CBOS 2.4.3.b
Note The following known issues also existed in CBOS 2.4.2, CBOS 2.4.2.b, and CBOS 2.4.3. They are listed here for your convenience. |
Caution Before you upgrade to CBOS release 2.4.2 or higher, make sure your running configuration and NVRAM configuration match. Otherwise, any running config commands that have not been saved to NVRAM are lost. |
Features/CPE Setup | Initiated inside with NAT | Initiated outside with NAT | Initiated inside without NAT | Initiated outside without NAT |
---|---|---|---|---|
video | yes | yes | yes | yes |
voice | yes | yes | yes | yes |
chat | yes | no | yes | yes |
whiteboard | yes | no | yes | yes |
file transfer | yes | no | yes | yes |
desktop sharing | yes | no | yes | yes |
desktop remote control | yes | no | yes | yes |
The following sections provide sources for obtaining documentation from Cisco Systems.
You can access the most current Cisco documentation on the World Wide Web at the following sites:
Cisco documentation and additional literature are available in a CD-ROM package, which ships with your product. The Documentation CD-ROM is updated monthly and may be more current than printed documentation. The CD-ROM package is available as a single unit or as an annual subscription.
Cisco documentation is available in the following ways:
If you are reading Cisco product documentation on the World Wide Web, you can submit technical comments electronically. Click Feedback in the toolbar and select Documentation. After you complete the form, click Submit to send it to Cisco.
You can e-mail your comments to bug-doc@cisco.com .
To submit your comments by mail, use the response card behind the front cover of your document, or write to the following address:
Attn Document Resource Connection
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-9883
We appreciate your comments.
Cisco provides Cisco.com as a starting point for all technical assistance. Customers and partners can obtain documentation, troubleshooting tips, and sample configurations from online tools. For Cisco.com registered users, additional troubleshooting tools are available from the TAC website.
Cisco.com is the foundation of a suite of interactive, networked services that provides immediate, open access to Cisco information and resources at anytime, from anywhere in the world. This highly integrated Internet application is a powerful, easy-to-use tool for doing business with Cisco.
Cisco.com provides a broad range of features and services to help customers and partners streamline business processes and improve productivity. Through Cisco.com, you can find information about Cisco and our networking solutions, services, and programs. In addition, you can resolve technical issues with online technical support, download and test software packages, and order Cisco learning materials and merchandise. Valuable online skill assessment, training, and certification programs are also available.
Customers and partners can self-register on Cisco.com to obtain additional personalized information and services. Registered users can order products, check on the status of an order, access technical support, and view benefits specific to their relationships with Cisco.
To access Cisco.com, go to the following website:
The Cisco TAC website is available to all customers who need technical assistance with a Cisco product or technology that is under warranty or covered by a maintenance contract.
If you have a priority level 3 (P3) or priority level 4 (P4) problem, contact TAC by going to the TAC website:
P3 and P4 level problems are defined as follows:
In each of the above cases, use the Cisco TAC website to quickly find answers to your questions.
To register for Cisco.com, go to the following website:
http://www.cisco.com/register/
If you cannot resolve your technical issue by using the TAC online resources, Cisco.com registered users can open a case online by using the TAC Case Open tool at the following website:
http://www.cisco.com/tac/caseopen
If you have a priority level 1 (P1) or priority level 2 (P2) problem, contact TAC by telephone and immediately open a case. To obtain a directory of toll-free numbers for your country, go to the following website:
http://www.cisco.com/warp/public/687/Directory/DirTAC.shtm l
P1 and P2 level problems are defined as follows:
This document is to be used in conjunction with the documents listed in the "Obtaining Documentation" section.
Copyright © 2002, Cisco Systems, Inc.
All rights reserved.
Posted: Sat Sep 28 01:13:59 PDT 2002
All contents are Copyright © 1992--2002 Cisco Systems, Inc. All rights reserved.
Important Notices and Privacy Statement.