These release notes describe resolved and open issues for the Cisco Broadband Operating System (CBOS) Release 2.4. Please refer to previous release notes for specific information concerning past releases.
For more detailed information about the information in these release notes, refer to the "Related Documentation" section. Information about electronic documentation can be found in the "Cisco.com" section.
CBOS is the common operating system for Cisco customer premises equipment (CPE). The CBOS is modeled after Cisco IOS software and features a similar command syntax and format. This operating system is bundled with the CPE products listed below and can also be downloaded from Cisco Connection Online.
The CBOS Release 2.4 supports the following Cisco CPE products:
Follow these steps from the Entity Level. This is the preferred method.
Step 1 Right-click the cdcmCPE-? object.
Step 2 From the drop-down menu, select Configure.
Step 3 Select IP Static Route.
Step 4 In the Routing Policy field, enter the precedence bit value as follows.
precedence bit
Corresponding value in Routing Policy field
0
0
1
32
2
64
3
96
4
128
5
160
6
192
7
224
Step 5 In the object cdcpIpStaticRoutePolicy (Routing Policy), the precedence value and the policy code are contained in the least significant byte as follows:
Precedence: highest 3 bits
Policy code: the rest of 5 bits. (not used by CBOS)
Raw: in the Interface field, enter the PropVirtualInterface Index number of the interface whose precedence bit will be effective.
A Cisco 677 CPE device will not train up when using g.lite or g.dmt.
Condition:
When using g.lite or G.dmt on a 627 or 677, a Cisco 677 CPE device will not train up to a Cisco 6260 configured the same way.
Workaround:
Upgrade the ADI firmware to version 3.0. The name of the code required is RTBLD.BNM, available in a special file access area of CCO. You must be a registered CCO user. To download the RTBLD.BNM code, follow these steps:
Step 1 From any browser, log in to www.cisco.com.
Step 2 In Service and Support, select Software Center.
When attempting to use two or more PCs behind a CPE to do a file transfer with Microsoft networking to a Windows 2000 server, only one PC will be able to copy a file at a time.
Condition:
This occurs only under the following conditions:
Microsoft networking is the file transfer mechanism
more than one PC is attempting to do a file transfer at the same time
the CPE is running NAT
the file transfer is attempted from a Windows 2000 server on the far end of the connection.
Workaround:
Allow one PC at a time to do a file transfer using Microsoft networking, or use another file transfer method, such as FTP.
CSCds60974
Symptom:
When the CPE is set up as a DHCP client and is receiving its IP address from a DHCP server behind the terminating router (NRP on a 6400 or a 7200), the CPE may not receive an IP address from the DHCP server.
Condition:
This occurs with RFC1483 routing configured on a CPE which is configured to be a DHCP client and is trying to get DHCP information from a DHCP server over the wan interface. This problem does not apply to PPP routing, as there is no reason to use DHCP client functionality on the CPE in this situation; instead, IPCP should be used to obtain the IP address. It also does not apply if the DHCP server service is running on the 6400/7200; in this case, the CPE can receive an IP address from the DHCP server on the terminating router.
The problem that occurs is that the far-end DHCP server returns the IP address forwarded as a broadcast. The terminating router (6400/7200) receives this broadcast on its ethernet address, then, as it should, does not forward it over the ATM interfaces.
Workarounds:
There are two possible workarounds:
Put an IP helper address on the Ethernet interface of the 6400/7200 that points to the original IP address of the CPE.
Do not to attempt to have the CPE receive an IP address from a DHCP server over the WAN interface. The CPE, which is functioning as a router, should have a static IP address. If necessary, this address can be excluded from the DHCP server.
CSCds62558
Symptom:
When using auto-provisioning to configure DHCP pools for a CPE, if the first pool is not configured, it will still be enabled and given default values of IP 10.0.0.2, netmask 255.255.255.0, and size 252. This will cause this pool to be used first.
Condition:
This occurs when auto-provisioning is used to pass DHCP pool information to a CPE and the first pool on the CPE is not configured.
Workaround:
Always configure the first pool on the CPE when using auto-provisioning.
CSCds82039
Symptom:
When you attempt to set the DHCP relay command to an interface, only the wan0-0 interface is accepted as valid.
Condition:
This condition occurs when you attempt to use the eth0 interface for the DHCP relay command; for example, when SDSL modems are being used in a back-to-back environment.
Workaround:
No action is necessary. When the CPE is in the back-to-back configuration or the CPE mode is set to CO, the DHCP relay requests automatically go out the eth0 interface, even though the sho dhcp relay command shows the relay interface as wan0-0.
CSCds83490
Symptom:
Routing table updates are not received when RIPv2 is used.
Condition:
When the CPE device is configured with RIPv2 on a network with other RIPv2 routers, it does not receive routing table updates.
Workaround:
In addition to RIPv2 configuration, you must enable multicast forwarding on the CPE device. The CPE device cannot recognize multicast addresses if multicast forwarding is not enabled.
CSCds87618
Symptom:
When using multiple VCCs and VIP interfaces with PPP and NAT enabled, the VIP interfaces default to NAT outside interfaces.
Condition:
To use NAT across the VIP interfaces you have to change them to NAT inside interfaces.
Workaround:
Enter the following command:
set interface vip0 inside
or
Do not use NAT when using the VIP interfaces. If you must use NAT, direct all traffic to the wan0-0 interface. The wan0-0 interface remains as a NAT outside interface.
CSCds87680
Symptom:
The show NVRAM command sporadically produces unintelligible results.
Condition:
This occurs occasionally when the command is abbreviated to sh nv.
Workaround:
Issue the complete command show nvram.
CSCds49083
Symptom:
The mask for ethernet 0 (eth0) can be set to all 255s.
Condition:
When the mask of eth0 is set to 255.255.255.255, the interface will not appear in the routing table and is unusable.
Workaround:
Manually set the mask of eth0 to a number other than all 255s.
CSCds86083
Symptom:
When stats web command is entered on a CPE, the value of the field # of current connections may be artificially high, up to a value of over 4 billion.
Condition:
This problem can occur when a web connection is established to the CPE and left up for a prolonged period of time, such as overnight.
Workaround:
There is no workaround.
CSCds87384
Symptom:
When using multiple PVCs, for example, wan0-1 through wan0-7, and using the stats ip wan0-x command, only wan0-0 will display anything other than 0s for the statistics
Condition:
This occurs when using multiple PVCs and the stats ip command.
Workaround:
Obtain statistics on the amount of traffic by using other commands such as show ppp, show rfc1483, or show int wan0-x.
CSCds87418
Symptom:
When NAT is enabled on a CPE and a global outside IP address has been assigned via the command line interface (CLI) or auto-provisioning, but an IP address is also being received via IPCP, the global outside IP address will be that received via IPCP.
Condition:
This occurs under the following circumstances:
PPP routing is used on the CPE
NAT is enabled on the CPE
A global outside IP address is configured on the CPE from either the CLI or via auto-provisioning for the wan0-0 interface; the wan0-1 through wan0-7 interfaces do not have this issue
The terminating route (6400 NRP or 7200) has been configured to pass an IP address via IPCP to the CPE
Workaround:
There are two possible workarounds:
Configure the global outside IP address on the CPE or have the terminating router pass an IP address via IPCP. This avoids any potential conflicts between the global outside IP address on the wan0-0 interface and the IP address to be received via IPCP.
Use the command line interface to set the following parameter:
set ppp wan0-x ipcpIP address
where x is the applicable interface and IP address is the desired global outside IP address.
CSCds89064
Symptom:
When you try to set a password, any uppercase characters are converted to lowercase. Additionally, note that passwords set in a previous version of CBOS do retain their case after the CPE software is upgraded to Release 2.4.1.
Condition:
This occurs when using uppercase characters for both the exec or enable passwords.
Workaround:
The workaround is to use only lowercase characters.
Cisco documentation and additional literature are available in a CD-ROM package, which ships with your product. The Documentation CD-ROM is updated monthly and may be more current than printed documentation. The CD-ROM package is available as a single unit or as an annual subscription.
Nonregistered CCO users can order documentation through a local account representative by calling Cisco corporate headquarters (California, USA) at 408 526-7208 or, in North America, by calling 800 553-NETS(6387).
If you are reading Cisco product documentation on the World Wide Web, you can submit technical comments electronically. Click Feedback in the toolbar and select Documentation. After you complete the form, click Submit to send it to Cisco.
You can e-mail your comments to bug-doc@cisco.com.
To submit your comments by mail, for your convenience many documents contain a response card behind the front cover. Otherwise, you can mail your comments to the following address:
Cisco Systems, Inc. Document Resource Connection 170 West Tasman Drive San Jose, CA 95134-9883
Cisco provides Cisco.com as a starting point for all technical assistance. Customers and partners can obtain documentation, troubleshooting tips, and sample configurations from online tools. For Cisco.com registered users, additional troubleshooting tools are available from the TAC website.
If you are reading Cisco product documentation on the World Wide Web, you can submit comments electronically. Click Feedback in the toolbar and select Documentation. After you complete the form, click Submit to send it to Cisco. We appreciate your comments.
Cisco.com is the foundation of a suite of interactive, networked services that provides immediate, open access to Cisco information and resources at anytime, from anywhere in the world. This highly integrated Internet application is a powerful, easy-to-use tool for doing business with Cisco.
Cisco.com provides a broad range of features and services to help customers and partners streamline business processes and improve productivity. Through Cisco.com, you can find information about Cisco and our networking solutions, services, and programs. In addition, you can resolve technical issues with online technical support, download and test software packages, and order Cisco learning materials and merchandise. Valuable online skill assessment, training, and certification programs are also available.
Customers and partners can self-register on Cisco.com to obtain additional personalized information and services. Registered users can order products, check on the status of an order, access technical support, and view benefits specific to their relationships with Cisco.
The Cisco TAC website is available to all customers who need technical assistance with a Cisco product or technology that is under warranty or covered by a maintenance contract.
If you cannot resolve your technical issue by using the TAC online resources, Cisco.com registered users can open a case online by using the TAC Case Open tool at the following website:
If you have a priority level 1(P1) or priority level 2 (P2) problem, contact TAC by telephone and immediately open a case. To obtain a directory of toll-free numbers for your country, go to the following website:
P1—Your production network is down, causing a critical impact to business operations if service is not restored quickly. No workaround is available.
P2—Your production network is severely degraded, affecting significant aspects of your business operations. No workaround is available.
This document is to be used in conjunction with the Cisco Broadband Operating System 2.4 User Guide publication.
Access Registrar, AccessPath, Are You Ready, ATM Director, Browse with Me, CCDA, CCDE, CCDP, CCIE, CCNA, CCNP, CCSI, CD-PAC, CiscoLink, the Cisco NetWorks logo, Cisco Powered Network logo, Cisco Systems Networking Academy, Fast Step, FireRunner, Follow Me Browsing, FormShare, GigaStack, IGX, Intelligence in the Optical Core, Internet Quotient, IP/VC, iQ Breakthrough, iQ Expertise, iQ FastTrack, iQ Logo, iQ Readiness Scorecard, Kernel Proxy, MGX, Natural Network Viewer, Network Registrar, the Networkers logo, Packet, PIX, Point and Click Internetworking, Policy Builder, RateMUX, ReyMaster, ReyView, ScriptShare, Secure Script, Shop with Me, SlideCast, SMARTnet, SVX, TrafficDirector, TransPath, VlanDirector, Voice LAN, Wavelength Router, WebViewer, Workgroup Director, and Workgroup Stack are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, Empowering the Internet Generation, are service marks of Cisco Systems, Inc.; and Aironet, ASIST, BPX, Catalyst, Cisco, the Cisco Certified Internetwork Expert Logo, Cisco IOS, the Cisco IOS logo, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Collision Free, Enterprise/Solver, EtherChannel, EtherSwitch, FastHub, FastLink, FastPAD, IOS, IP/TV, IPX, LightStream, LightSwitch, MICA, NetRanger, Post-Routing, Pre-Routing, Registrar, StrataView Plus, Stratm, SwitchProbe, TeleRouter, and VCO are registered trademarks of Cisco Systems, Inc. or its affiliates in the U.S. and certain other countries.
All other brands, names, or trademarks mentioned in this document or Web site are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0010R)
