|
Table A-1 lists the system specifications for the Cisco 6400 carrier-class broadband aggregator.
Description | Specifications |
---|---|
5 Gbps1 shared memory, nonblocking switch fabric | |
Software images | Default image |
21.75 in. x 17.5 in. x 12.0 in. (55.2 cm x 44.4 cm x 30.4 cm) standard 19-in. rack mount | |
Chassis minimum configuration (1 NSP, 1 PEM): 80 lb (37 kg) | |
Input power requirement | 1200W maximum (PEM-PWR-DC) (DC version) |
1200W maximum, 900W typical with maximum configuration | |
1200W (3768 Btu2/hr) (DC version) | |
DC input voltage range | -40.5 to -72 VDC (rated -48/-60 VDC) |
Maximum power budget: 20A @ -48 VDC | |
AC input voltage range | 90 to 255 VAC (rated 100 to 240 VAC using AC PEM) (See Cisco 6400 Hardware Installation and Maintenance Guide, Appendix D for AC power shelf ratings) |
15A @ 100 VAC, 7A @ 240 VAC, using AC PEM (See Cisco 6400 Hardware Installation and Maintenance Guide, Appendix D for AC power shelf ratings) | |
140 cfm3 through the system blower module 200 cfm through the system blower module when the exhaust temperature exceeds 40ºC | |
25 to 104ºF (-4 to 40ºC) Short-term operating temperature is limited to 131ºF (55ºC) in compliance with | |
Nonoperating temperature range | -40 to 167ºF (-40 to 75ºC) |
5 to 95%, noncondensing | |
-200 to 10,000 ft (-61 to 3048 m) | |
Loop timing, network timing derived from any NLC interface, Stratum 4 accuracy when internally timed. NSP-S3B also allows network timing from CO BITS, Stratum 3 accuracy when internally timed. | |
Node switch processor (NSP) | 64 MB DRAM, 8 MB Flash memory, 20 MB FlashDisk card (C6400-NSP-1) |
Node route processor (NRP) | 64 MB DRAM, 8 MB Flash memory (C6400-NRP-1) |
Full-height node line card (NLC) carrier module | Carrier module for 2 half-height NLCs with covers for empty slots installed (C6400-CARRIER) |
OC-3/STM-1 NLC | NLC with 2 SONET STS-3c/SDH STM-1 single-mode intermediate reach fiber ports, |
Fiber-optic power levels: OC-3 single-mode intermediate reach Output center wavelength |
|
DS3 NLC | NLC with 2 coaxial cable connections with BNC connectors (NLC-2DS3-BNC) Maximum station-to-station cabling distance is 450 ft (137 m) |
OC-12/STM-4 NLC | NLC with 1 SONET STS-12c/SDH STM-4 single-mode intermediate reach fiber ports, SC connector (NLC-1OC12-SM) |
Fiber-optic power levels: OC-12 single-mode intermediate reach Output center wavelength |
|
NSP interface ports | RJ-45 IEEE 802.3 Ethernet 10BaseT |
ATM connections | 32,000 point-to-point, 2048 point-to-multipoint (maximum) |
Network management | Port TX and RX LEDs, switch and common equipment status LEDs |
Mean time between failures | 17 years per RIN |
10BaseT EthernetCategory 3-5 UTP: 328 ft (100 m) | |
Safety: Emission: Immunity: |
1Gbps = gigabits per second 2Btu = British thermal units 3cfm = cubic feet per minute 4nm = nanometers |
Note If the Cisco 6400 is used in an environment where lightning-induced transients are likely to couple to the signal lines, use of shielded interconnection cables for the 100BaseT ports is highly recommended. In addition, use of shielded interconnection cables for the 100BaseT ports is required to meet Bellcore GR1089 CORE Section 4.5.9 and ETSI section 5.2.2.2 (intrabuilding lightning surge). |
Posted: Fri Jul 5 11:02:52 PDT 2002
All contents are Copyright © 1992--2002 Cisco Systems, Inc. All rights reserved.
Important Notices and Privacy Statement.