|
|
This chapter lists the features supported by the Cisco 6400 carrier-class broadband aggregator in Cisco IOS Release 12.2(13)T and identifies feature documentation that you can find on Cisco.com.
Feature documentation publication names are in italics. When applicable, the path to the most useful section of the publication is provided in a bulleted list after the publication name. The bulleted items can be book part titles, chapter titles, section names, or subsection names.
Table 1-1 Examples of Conventions Used in the "Supported Features" Chapter
|
The Cisco 6400 supports three node route processors, designated as NRP-1, NRP-2, and NRP-2SV:
The Feature column states whether the NRP feature is supported by or applicable to only one or two types of NRP.
Table 1-2 NRP Features—Access Protocols
|
1 IRB = integrated routing and bridging 2 IPCP = IP Control Protocol 3 PPPoA = PPP over ATM 4 PPPoE = PPP over Ethernet 5 SNAP = Subnetwork Access Protocol 6 RBE = Routed Bridge Encapsulation 7 DHCP = Dynamic Host Configuration Protocol |
Table 1-3 NRP Features—Aggregation and VPNs
|
|
1 L2TP = Layer 2 Tunnel Protocol 2 MPLS = Multiprotocol Label Switching 3 VPN = Virtual Private Network 4 LSR = label switch router 5 LDP = label distribution protocol 6 LSC = label switch controller 7 ISL = Inter-Switch Link |
Table 1-4 NRP Features—Configuration and Monitoring
|
|
1 PVC = permanent virtual circuit (or connection) 2 VC = virtual circuit (or connection) |
Table 1-5 NRP Features—Hardware Support
|
|
1 FE = Fast Ethernet 2 NME = Network Management Ethernet |
Table 1-6 NRP Features—IP and Routing
|
|
1 ARP = Address Resolution Protocol 2 BGP4 = Border Gateway Protocol Version 4 3 EIGRP = Enhanced Interior Gateway Routing Protocol 4 GRE = generic routing encapsulation 5 IGMP = Internet Group Management Protocol 6 IS-IS = Intermediate System-to-Intermediate System 7 NAT = Network Address Translation 8 OSPF = Open Shortest Path First 9 PIM = Protocol Independent Multicast 10 RIP = Routing Information Protocol 11 TCP = Transmission Control Protocol 12 UDP = User Datagram Protocol 13 WCCP = Web Cache Communication Protocol |
Table 1-7 NRP Features—Network Management
|
|
1 SNMP = Simple Network Management Protocol 2 OAM = Operation, Administration, and Maintenance |
Table 1-8 NRP Features—QoS
|
Table 1-9 NRP Features—RADIUS/AAA
|
|
1 PAP = Password Authentication Protocol 2 CHAP = Challenge Handshake Authentication Protocol 3 VPI = virtual path identifier 4 VCI = virtual channel identifier |
Table 1-10 NRP Features—Scalability and Performance
|
| 1 CEF = Cisco Express Forwarding |
Table 1-11 NRP Features—SSG
|
|
1 PTA = PPP Termination Aggregation 2 AAA = authentication, authorization, and accounting 3 DNS = Domain Name System |
Table 1-12 NRP Features—Other Features and Feature Enhancements
|
The Node Switch Processor (NSP) contains the ATM switch engine and processor, and most memory components.
Table 1-13 NSP Features—Aggregation and VPNs
|
| 1 LSR = label switch router |
Table 1-14 NSP Features—ATM Connections
|
|
1 OAM = Operation, Administration, and Maintenance 2 VP = virtual path 3 UNI = User-Network Interface 4 PVC = permanent virtual circuit (or connection) 5 PVP = permanent virtual path 6 SVC = switched virtual circuit 7 VCC = virtual channel connection 8 VPC = virtual path connection |
Table 1-15 NSP Features—ATM Internetworking
|
|
1 LES = LAN Emulation Server 2 LECS = LAN Emulation Configuration Server 3 ARP = Address Resolution Protocol |
Table 1-16 NSP Features—ATM Per-Flow Queuing
|
|
1 The NSP uses the FC-PFQ feature card. 2 EPD = early packet discard |
Table 1-17 NSP Features—ATM Traffic Classes
|
|
1 ABR = available bit rate 2 EFCI = Explicit Forward Congestion Indication 3 RR = relative rate 4 MCR = minimum cell rate 5 CBR = constant bit rate 6 The NSP uses the FC-PFQ feature card. 7 UBR = unspecified bit rate 8 VBR-nrt = variable bit rate, non-real time 9 VBR-rt = variable bit rate, real time |
Table 1-18 NSP Features—Configuration and Monitoring
|
|
1 ILMI = Interim Local Management Interface 2 PCMCIA = Personal Computer Memory Card International Association |
Table 1-19 NSP Features—Hardware Support
|
|
1 EHSA = enhanced high system availability 2 NME = Network Management Ethernet 3 APS = automatic protection switching 4 BITS = building integrated timing supply |
Table 1-20 NSP Features—IP and Routing
|
|
1 DHCP = Dynamic Host Configuration Protocol 2 NTP = Network Time Protocol |
Table 1-21 NSP Features—Network Management
|
|
1 RMON = remote monitoring 2 SNMP = Simple Network Management Protocol |
Table 1-22 NSP Features—QoS
|
Table 1-23 NSP Features—RADIUS/AAA
|
Table 1-24 NSP Features—Scalability and Performance
|
| 1 ITT = Input Translation Table |
Table 1-25 NSP Features—Signaling and Routing
|
|
1 NSAP = network service access point 2 CUG = closed user group 3 PNNI = Private Network-Network Interface 4 ILMI = Interim Local Management Interface 5 IISP = Interim-Interswitch Signaling Protocol 6 UNI = User-Network Interface |
Posted: Thu Jan 29 19:53:06 PST 2004
All contents are Copyright © 1992--2004 Cisco Systems, Inc. All rights reserved.
Important Notices and Privacy Statement.