![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() |
These release notes are for Cisco IOS Release 12.3(1a)BW running on the Cisco Multiprocessor WAN Application Module (MWAM) in the Cisco 7600 Internet router. These release notes are updated as needed to describe new features, memory requirements, hardware support, software platform deferrals, and changes to the microcode and related documents.
For a list of the software caveats that apply to Cisco IOS Release 12.3(1a)BW, see the "Caveats in Cisco IOS Release 12.3(1a)BW" section.
To see the release notes for Cisco IOS Release 12.3, see http://www.cisco.com/univercd/cc/td/doc/product/software/ios123/123relnt/xprn123/index.htm .
This document contains the following sections:
The Cisco Multiprocessor WAN Application Module (MWAM) is a Cisco IOS software application module that you can install into the Cisco 7600 Series Internet Routers. The MWAM allows you to run multiple instances of Cisco Ethernet Service Aggregation applications, such as L2TP Network Server (LNS) and Service Selection Gateway (SSG) application software.
The MWAM requires the following system configuration:
Refer to the Release Notes for Cisco IOS Release 12.2(14)ZA1 on the Catalyst 6500 Series and Cisco 7600 Series Supervisor Engine and MSFC for specific information about the Supervisor Engine 2.
Refer to the C isco Multiprocessor WAN Application Module Installation and Configuration Notes for the Cisco 7600 Series Internet Router for specific information about configuring the MWAM.
MWAM memory is not configurable.
To use a MWAM module, you need a Cisco Catalyst 6500 Series Supervisor Engine 2 with an MSFC 2 and any interface module with ports to connect server and client networks.
![]() |
Note Release 12.2(14)ZA1 does not support optical service modules (OSMs) or the Catalyst 6500 Series and Cisco 7600 Series Internet Router FlexWAN module because of open caveats CSCdx94072, CSCdx83584, CSCdx57576, CSCdx60406, CSCdx69921, and CSCdx63685. |
This section describes system requirements for MWAM with Cisco IOS Release 12.3(1a)BW.
MWAM with Cisco IOS Release 12.3(1a)BW requires the following hardware components:
A Hardware-Software Compatibility Matrix is available on CCO for users with CCO login accounts. This matrix allows users to search for supported hardware components by entering a Cisco platform and IOS release. The Hardware-Software Compatibility Matrix tool is available at the following URL:
http://www.cisco.com/cgi-bin/front.x/Support/HWSWmatrix/hwswmatrix.cgi
MWAM with Cisco IOS Release 12.3(1a)BW requires the following software components:
Cisco IOS Release 12.3(1a)BW is a special release that supports Cisco IOS Release 12.(3)1and the same features that are in previous Cisco IOS Release 12.2 releases, with the addition of MWAM platform support.
The MWAM provides two processor complexes that are equipped with 1 GB memory shared between two processors (512 MB each). The remaining processor complex is equipped with 512 MB memory shared between two processors (256 MB each). The total memory capacity for the MWAM is 2.5 GB.
The MWAM memory is not configurable.
To determine the version of Cisco IOS software running on your router, log in to the router and enter the show version EXEC command:
For information on upgrading to a new software release, see the product bulletin Cisco IOS Software Upgrade Ordering Instructions located at:
http://www.cisco.com/warp/public/cc/pd/iosw/prodlit/957_pp.htm
For information on upgrading images on the MWAM, refer to the Cisco Multiprocessor WAN Application Module Installation and Configuration Notes for the Cisco 7600 Series Internet Router.
![]() |
Note The image download process automatically loads the Cisco IOS image onto the three processor complexes on the MWAM. |
This section describes the features associated with the MWAM with Cisco IOS Release 12.3(1a)BW.
Each MWAM card's six CPUs share a common Cisco IOS image but each runs independently of the others so that there are six unique IOS instances running simultaneously. These IOS instances use gigabit Ethernet 802.1Q trunk port interfaces to carry VLAN encapsulated traffic to and from the network through the Cisco 7600 switching hardware. Each processor complex (housing two IOS instances) shares one gigabit Ethernet interface.
Each processor complex has a 1 Gigabit Ethernet (GE) interface to the switching bus. This connection appears as a GE interface from the Supervisor module.
The MWAM connects to the Cisco Catalyst 6500 switch/Cisco 7600 router bus for data and control traffic.
The MWAM with Cisco IOS Release 12.3(1a)BW provides the SSG features on the MWAM platform.
The SSG requires that you bind the user access network and services network to specific interfaces. Only one physical interface is available to the SSGs on the MWAM, which connects to the switching bus and Cisco Catalyst 6500 Series Supervisor Engine 2 module. Subinterfaces are defined with 802.1Q encapsulation and contain multiple VLANs, each representing one network interface.
The full description of SSG features is included in the release documentation:
http://www.cisco.com/univercd/cc/td/doc/product/software/ios123/123newft/123limit/1231abw/index. htm.
The MWAM with Cisco IOS Release 12.3(1a)BW also provides L2TP Network Server (LNS) on the MWAM platform.
LNS operates on any platform capable of PPP termination. It handles the server side of the L2TP protocol. Since L2TP relies on the single media over which L2TP tunnels arrive, an LNS may have only a single LAN or WAN interface, yet still be able to terminate calls arriving at any of the LACs' full range of PPP interfaces (async ISDN). LNS is the initiator of outgoing calls and the receiver of incoming calls.
For more information, see http://www.cisco.com/univercd/cc/td/doc/product/software/ios123/123mindx/new123.htm#34929.
External physical interfaces provided by the supported platforms are not visible to the SSG software. This is an important advantage of the MWAM implementation when compared to the 7200/7400 platform. The MWAM implementation protects the SSG from interface and link failures. As long as the platform provides redundant links to other system components (for example, GGSN, AAA servers), the SSG configuration is not affected and its operation is maintained.
The following sections describe the open, resolved, closed, and unreproducible caveats for the MWAM with Cisco IOS Release 12.3(1a)BW.
![]() |
Note If you have an account with Cisco.com, you can use Bug Navigator II to find caveats of any severity for any release. To reach Bug Navigator II, log in to Cisco.com and click Software Center: Cisco IOS Software: Cisco Bugtool Navigator II. Another option is to go directly to http://www.cisco.com/support/bugtools. |
Table 1 Open Caveats
The following sections describe the documentation available related to the Cisco Multiprocessor WAN Application Module. These documents consist of hardware and software installation guides, Cisco IOS configuration guides and command references, system error messages, and other documents.
Documentation is available as printed manuals or electronic documents.
These documents are available for the Catalyst 6500/Cisco 7600 series platforms on Cisco.com and the Documentation CD-ROM:
Catalyst 6500 Series Switch Documentation is available at the following URL:
http://www.cisco.com/univercd/cc/td/doc/product/lan/cat6000/index.htm
Cisco 7600 Series Routers Documentation is available at the following URL:
http://www.cisco.com/en/US/products/hw/routers/ps368/products_installation_guides_books_list.html
These sections explain how to obtain documentation from Cisco Systems.
You can access the most current Cisco documentation on the World Wide Web at this URL:
Translated documentation is available at this URL:
http://www.cisco.com/public/countries_languages.shtml
Cisco documentation and additional literature are available in a Cisco Documentation CD-ROM package, which is shipped with your product. The Documentation CD-ROM is updated monthly and may be more current than printed documentation. The CD-ROM package is available as a single unit or through an annual subscription.
You can order Cisco documentation in these ways:
http://www.cisco.com/cgi-bin/order/order_root.pl
http://www.cisco.com/go/subscription
You can submit comments electronically on Cisco.com. In the Cisco Documentation home page, click the Fax or Email option in the "Leave Feedback" section at the bottom of the page.
You can e-mail your comments to bug-doc@cisco.com.
You can submit your comments by mail by using the response card behind the front cover of your document or by writing to the following address:
Cisco Systems
Attn: Document Resource Connection
170 West Tasman Drive
San Jose, CA 95134-9883
Cisco provides Cisco.com as a starting point for all technical assistance. Customers and partners can obtain online documentation, troubleshooting tips, and sample configurations from online tools by using the Cisco Technical Assistance Center (TAC) Web Site. Cisco.com registered users have complete access to the technical support resources on the Cisco TAC Web Site.
Cisco.com is the foundation of a suite of interactive, networked services that provides immediate, open access to Cisco information, networking solutions, services, programs, and resources at any time, from anywhere in the world.
Cisco.com is a highly integrated Internet application and a powerful, easy-to-use tool that provides a broad range of features and services to help you with these tasks:
If you want to obtain customized information and service, you can self-register on Cisco.com. To access Cisco.com, go to this URL:
The Cisco Technical Assistance Center (TAC) is available to all customers who need technical assistance with a Cisco product, technology, or solution. Two levels of support are available: the Cisco TAC Web Site and the Cisco TAC Escalation Center.
Cisco TAC inquiries are categorized according to the urgency of the issue:
The Cisco TAC resource that you choose is based on the priority of the problem and the conditions of service contracts, when applicable.
You can use the Cisco TAC Web Site to resolve P3 and P4 issues yourself, saving both cost and time. The site provides around-the-clock access to online tools, knowledge bases, and software. To access the Cisco TAC Web Site, go to this URL:
All customers, partners, and resellers who have a valid Cisco service contract have complete access to the technical support resources on the Cisco TAC Web Site. The Cisco TAC Web Site requires a Cisco.com login ID and password. If you have a valid service contract but do not have a login ID or password, go to this URL to register:
http://www.cisco.com/register/
If you are a Cisco.com registered user, and you cannot resolve your technical issues by using the Cisco TAC Web Site, you can open a case online by using the TAC Case Open tool at this URL:
http://www.cisco.com/tac/caseopen
If you have Internet access, we recommend that you open P3 and P4 cases through the Cisco TAC Web Site.
The Cisco TAC Escalation Center addresses priority level 1 or priority level 2 issues. These classifications are assigned when severe network degradation significantly impacts business operations. When you contact the TAC Escalation Center with a P1 or P2 problem, a Cisco TAC engineer automatically opens a case.
To obtain a directory of toll-free Cisco TAC telephone numbers for your country, go to this URL:
http://www.cisco.com/warp/public/687/Directory/DirTAC.shtml
Before you call, check with your network operations center to determine the level of Cisco support services to which your company is entitled: for example, SMARTnet, SMARTnet Onsite, or Network Supported Accounts (NSA). When you call the center, have your service agreement number and your product serial number available.
Posted: Fri Nov 7 06:47:21 PST 2003
All contents are Copyright © 1992--2003 Cisco Systems, Inc. All rights reserved.
Important Notices and Privacy Statement.