|
|
Is Cisco documentation helpful? Click here or go to http://www.cisco.com/warp/public/732/docsurvey/rtg/ to give us your feedback.
The Cisco 7505 has five slots: one slot for the Route Switch Processor (RSP) and slots 0, 1, 2, and 3 for the interface processors. The Cisco 7505 uses a single power supply, with two models available: DC input or AC input.
Note For detailed hardware installation instructions and safety guidelines, refer to the Cisco 7500 Series Router Installation and Configuration Guide, Site Preparation and Safety Guide, and the Cisco 7500 Regulatory Compliance and Safety Guide.
 | Warning Only trained and qualified personnel should install, replace, or service this equipment. |
Step 2 Ensure the power service at the site is suitable for the router you are installing.
Step 3 Check the packing slip to ensure that all the proper components are present.
Step 4 Confirm that you have the required tools and parts:
For cable-management brackets:
Step 2 Use the four M4 x 10-mm screws provided to attach the ears to the sides of the chassis, as shown in B. (Use two screws per ear.)
| Warning To prevent injury, two people are required to lift the chassis. Grasp the chassis underneath the lower edge, and lift with both hands. To prevent injury, keep your back straight and lift with your legs, not your back. |
Step 3 Use the eight 10-32 x 3/8-inch screws provided to attach the ears to the mounting strips, as shown in C. Use four screws per ear and mounting strip.
Step 4 Level the chassis as required. Provide two inches of clearance on either side of the chassis.
The Route Switch Processor (RSP) comes uninstalled with your Cisco 7505 router, but is a required system component. Install the RSP in the RSP slot, and install any interface processors, fillers, or Versatile Interface Processors (VIPs) in slots 0, 1, 2, and 3.
Step 2 Place the interface processor, filler, VIP, or RSP in the slot and align the guide on the carrier with the groove in the slot, as shown in A.
Step 3 Carefully slide the interface processor, filler, VIP, or RSP into the slot until the faceplate makes contact with the ejector levers.
Step 4 Use the thumb and forefinger of each hand to push the ejector levers flat against the interface processor, filler, VIP, or RSP, as shown in B.
Step 5 Use a screwdriver to tighten the captive installation screws, as shown in C.
Step 6 Repeat Step 1 through Step 5 to install the RSP or any additional interface processors, fillers, or VIPs.
Note Refer to the "Check the RSP Installation" section 19 to check the RSP installation. Refer to the "Check the Interface Processor or VIP Installation" section to check the interface processor or VIP installation.
Step 2 Insert three M3 x 8-mm Phillips screws, and tighten slightly with your finger.
Step 3 Use a Phillips Number 1 screwdriver to tighten all three screws.
Step 4 Repeat Step 1 through Step 3 for the second bracket.
Step 5 Route the interface cables through the brackets.
The Cisco 7505 router supports AC-input and DC-input power supplies. The power supply is already installed in the router when you receive it. You connect the power to it.
Note The AC-input power supply is the shipped as the default if no power supply is specified at the time of purchase.
Step 2 Connect the opposite end of the power cable to an appropriate power source.
Step 2 Loosen the two captive screws that secure the terminal block cover, as shown in A.
Step 3 Pull the terminal block cover away from the terminal block, as shown in B.
Step 4 Feed the return (RTN) and -48V wires through the large hole in the terminal block cover, as shown in C.
Step 5 Attach a nylon cable tie to secure the cables to the terminal block cover.
Step 6 Attach the RTN and -48 leads to the terminal block, as shown in C.
Note Match the color coding at the DC source. Typically, green or green/yellow is used for ground, black is used for RTN, and red or white is used for -48V.
Step 7 Attach the ground cable to the ground terminal.
Step 8 Replace the terminal block cover, as shown in B.
Step 9 Tighten the captive screws on the terminal block cover, as shown in A.
The system console port on the RSP is a DB-25 receptacle DCE port for connecting a data terminal, which allows you to configure and manage the system. The console port is labeled Console.
Step 2 Check your terminal's documentation to determine the baud rate of the terminal you will be using.
Step 3 Set up the terminal as follows: 9600 baud, 8 data bits, no parity, and 2 stop bits (9600, 8N2).
The auxiliary port on the RSP is an ETA/TIA DTE DB-25 plug to which you can attach external equipment in order to access the router from the network. The port is located next to the console port on the RSP and is labeled AUX.
Step 2 Check your terminal's documentation to determine the baud rate of the terminal.
Step 3 Set up the terminal as follows: 9600 baud, 8 data bits, no parity, and 2 stop bits (9600, 8N2).
Step 2 Check the console terminal to make sure it is connected to the console port and turned on.
Step 3 Turn the system power switch to the on (|) position. The green AC (or DC) OK and fan OK LEDs on each power supply should go on. After a few seconds, the red output fail LED will turn off.
Step 4 Listen for the system blower; you should immediately hear it operating.
Step 5 Observe the normal LED indicator on the RSP. If this indicator is not on after system initialization, an error has occurred. If necessary, refer to Appendix A in the Cisco 7500 Series Installation and Configuration Guide.
Step 6 Wait until the system boot is complete before attempting to verify the status of interface processor indicators. During the boot process, the LED indicators on most of the interfaces go on and off in irregular sequence.
Step 7 Observe the LED indicators on the interface processors in your system. When the system boot is complete (a few seconds), the RSP begins to initialize the interface processors. During this initialization, the indicators on each interface processor behave differently (most flash on and off).
The enabled LED on each interface processor goes on when initialization has been completed, and the console screen displays a script and system banner similar to the following:
Step 8 Observe the system startup banner. When you start up the router for the first time, the system automatically enters the setup command facility, which determines which interfaces are installed and prompts you for configuration information for each one. On the console terminal, after the system displays the system banner and hardware configuration, you will see the following System Configuration Dialog prompt:
Many privileged-level EXEC commands are used to set operating parameters. To enter the privileged-level:
Step 2 Enter the configure terminal command to enter configuration mode:
Step 3 Enter the config-register value configuration command, where value is a hexadecimal number preceded by 0x, as in the following example:
Step 4 Press Ctrl-Z to exit configuration mode.
Step 5 Save the new settings to NVRAM. Enter the copy running-config startup-config command.
Note The new settings do not take effect until the system software is reloaded by rebooting the router.
Step 6 Enter the show version command to view the configuration register value currently in effect. The value is displayed on the last line of the screen display:
Step 7 Reboot the router, and then perform a basic configuration using:
Note Configuration register changes take effect only when the system reloads, such as when you issue a reload command from the console.
Step 8 Connect to the network using a serial (WAN) cable to the channel service unit/data service unit (CSU/DSU).
Step 9 Contact your system administrator to verify that the TCP/IP host on your network is preconfigured.
Step 10 Press Ctrl-Z to exit configuration mode.
Step 11 At the # prompt, enter the copy running-config startup-config command to save the configuration to NVRAM as follows:
This completes the procedure for performing a basic configuration using AutoInstall.
Note The router's serial (WAN) cable should not be connected to the CSU/DSU unless you are planning to use AutoInstall. If you are using the console Y-cable that shipped with your router, use either of the two DB-25 male plug ends of the Y-cable.
Step 2 Enter the enable secret password and the enable password when the following is displayed:
Step 3 Enter yes or no to accept or refuse SNMP management:
Step 4 Enter no to refuse to enable CLNS:
Step 5 Enter yes to enable routing on AppleTalk and IPX:
Step 6 Enter no to refuse to enable Vines, XNS, DECnet, or bridging:
Step 7 Enter yes or press Return to configure IP, and then select an interior routing protocol for IP, if you are using IP routing:
Step 8 At the # prompt, enter the copy running-config startup-config command to save the configuration to NVRAM as follows:
Step 2 Enter yes to enable IPX on this interface, using the IPX network number:
Step 3 Enter yes to enable AppleTalk on this interface, to configure for extended AppleTalk networks, and then enter the cable range number. Enter the zone name and any other additional zones that will be associated with your local zone:
Step 4 At the # prompt, enter the copy running-config startup-config command to save the configuration to NVRAM as follows:
Step 2 Determine which protocols you want to allow on the synchronous serial interface and enter the appropriate responses:
Step 3 Press Ctrl-Z to exit configuration mode.
Step 4 At the # prompt, enter the copy running-config startup-config command to save the configuration to NVRAM as follows:
Your Cisco 7505 router is now minimally configured and ready to use. If you want to modify the parameters after the initial configuration, use the setup command. To perform more complex configurations, use the configure command. For more information on additional interface configuration and information on more specific system configurations, refer to the Cisco 7500 Series Installation and Configuration Guide.
At the reboot, the following example appears:
Step 2 Enter the interface type slot/port command at the enable prompt to enter interface configuration mode, as follows:
Step 3 Press Ctrl-Z to exit configuration mode.
Step 4 At the # prompt, enter the copy running-config startup-config command to save the configuration to NVRAM as follows:
Your Cisco 7505 router is now minimally configured and ready to use. If you want to modify the parameters after the initial configuration, use the setup command. To perform more complex configurations, use the configure command. For more information on additional interface configuration and information on more specific system configurations, refer to the Cisco 7500 Series Installation and Configuration Guide.
A Flash memory card that ships with your Cisco 7505 contains the Cisco IOS software image to boot your router. You do not need to format it.
The RSP has two PC Card slots—slot 0 and slot 1—into which you can install a Flash memory card. PC Card slot 0 is on the top and slot 1 is on the bottom.
Note A Flash memory card can be inserted and removed with the system power on. Both PC Card slots can be used at the same time.
Step 2 Remove the card from the slot and place it in an antistatic bag to protect it.
Step 3 Face the front panel of the RSP, and hold the Flash memory card with the connector end of the card toward the slot.
Note The Flash memory card is keyed and cannot be seated the wrong way. The eject button will not pop out if the card is not properly inserted.
Step 4 Insert the card into the appropriate slot until the card completely seats in the connector at the back of the slot and the eject button pops out toward you.
Note The card does not insert all the way inside the RSP; a portion of the card remains outside of the slot. Do not attempt to force the card past this point.
Flash memory cards shipped as spare parts must be formatted. Use only Intel Series 2+ Flash memory cards.
Step 2 At the erase all sectors prompt, press Enter to proceed.
Step 3 At the volume ID prompt, enter the ID name:
To upgrade to a new Cisco IOS image, copy the image file to Flash memory. Upgrade images one at a time; do not delete all known good images at one time. You cannot copy an image while the system is running from Flash memory.
Use the command copy tftp:filename [bootflash | slot0 | slot1]: filename for the copy procedure, where tftp:filename is the source of the file and [bootflash | slot0 | slot1]: filename is the destination in bootflash memory or on either of the Flash memory cards.
An example of the copy tftp:filename command follows for a file in the Flash memory card in PC Card slot 0:
Step 2 Enter the no boot system command, as follows.
Step 3 Enter the boot system flash slot0:new.image command, as follows:
Step 4 Enter the config-register 0x2102 command to enable loading an image from Flash memory:
Step 5 Press Ctrl-Z to exit configuration mode.
Step 6 Enter the copy running-config startup-config command to save the configuration to NVRAM as follows:
Step 7 Enter the reload command. When the system reloads, it will boot the image new.image from the Flash memory card in slot 0.
To enable booting from Flash memory, set configuration register bits 3, 2, 1, and 0 to a value between 2 and 15 in conjunction with the boot system flash device:filename configuration command, where device is bootflash:, slot0:, or slot1:, and filename is the name of the file from which you want to boot the system. In the following example, the Flash memory card is in slot 0.
Step 2 At the prompt, enter configuration commands, one per line.
Step 3 Press Ctrl-Z to exit configuration.
Step 4 Enter the boot system flash bootflash:slot0: filename command, as follows:
Step 5 Enter the config-register command with the value shown in the following example:
Step 6 Press Ctrl-Z to exit enable booting mode.
To remove and install an RSP, you will perform the following steps:
Note Do not shut down the system power when removing an interface processor or VIP. However, if you are removing the RSP, first copy the configuration file to a TFTP server (see the "Copy the Configuration File for an RSP" section), and then return to this section to complete the procedure.
Step 2 Disconnect all cables from the interface processor, VIP, or RSP port adapters. If you are only moving a carrier, skip this step.
Step 3 Use a screwdriver to loosen the captive installation screws, as shown in A.
Step 4 Place your thumbs on both ejector levers and simultaneously pull them both outward, as shown in B.
Step 5 Grasp the interface processor, filler, VIP, or RSP handle with one hand and pull the carrier straight out of the slot, keeping your other hand under the carrier to guide it.
Step 6 Store the interface processor, VIP, or RSP in an antistatic bag.
Step 7 Repeat Step 2 through Step 6 to remove any additional interface processors, fillers, VIPs, or RSPs. Refer to the "Install Interface Processors, Fillers, VIPs, and RSPs" section to install an interface processor, filler, VIP, or RSP.
Step 2 Observe the RSP LEDs. While the system initializes, the CPU halt LED on the RSP stays on. It goes off when the boot process is complete. As the RSP initializes each interface processor, the status LEDs on each interface processor go on and off in irregular sequence.
Step 3 Verify that the console terminal displays the system banner and startup screen as the system restarts.
Step 4 Verify that all the enabled LEDs (on the interface processors) are on.
Step 5 When you have verified all the conditions in Step 1 through Step 4, the installation is complete.
If you replaced the RSP and saved your configuration file to a remote server before doing so, proceed to the "Retrieve the Configuration File for RSPs" section.
An error condition exists if no LEDs go on at power up or after initialization, or if the boot error or CPU halt LEDs go on and remain on. If this happens, see Appendix A in the Cisco 7500 Series Installation and Configuration Guide.
Note When a new VIP is inserted or when a VIP is moved to a new slot, the system recognizes the new interfaces, but leaves them in the shutdown state until you configure them. After the system reinitializes all interfaces, the enabled LED on the port adapters and on all interface processors, VIPs, and RSPs should go on, depending on your connections and configuration.
Step 2 Verify that the enabled LED on each port adapter goes on and remains on.
If the enabled LED on a port adapter fails to go on, the interface processor or VIP may not be fully seated in the backplane. Refer to Appendix A in the Cisco 7500 Series Installation and Configuration Guide.
Step 3 If the VIP is new, configure the new interfaces.
Step 4 If the VIP is a replacement, use the show interfaces type slot/port adapter/port or show controllers cbus command to verify the status of the interfaces.
If you replaced a VIP with a new VIP with a greater number of ports (for example, if you replaced a single-port adapter VIP with a dual-port adapter VIP), the system will recognize the interfaces on the previously configured port adapter, but will not recognize the additional port adapter interfaces. The new interfaces will remain in the shutdown state until you configure them.
Step 5 When the interfaces are up, check the activity of each interface by observing the status LEDs, which are described in the LED section of your port adapter documentation.
Refer to the appropriate Cisco IOS software documentation for the configuration options available, and for specific configuration instructions, as needed.
Before you copy (save) the running configuration to a TFTP file server, ensure the following:
Step 2 Enter the ping command followed by the name or IP address of the remote server, and then press Return to check the connection between the router and the remote host.
Step 3 Enter the show running-config command to display the currently running configuration on the terminal and ensure that the configuration information is complete and correct. If it is not, use the configure command to add or modify the existing configuration.
Step 4 Create a file on the TFTP server.
Note Before you can save a file to a TFTP server, a file must first exist on the TFTP server. Create this file. Ensure that the filename matches the filename you will copy from the router. Also, ensure that the server permissions are set so the router can copy to this file.
Step 5 Issue the copy startup-config tftp command. The EXEC command interpreter prompts you for the name or interface processor address of the remote host that is to receive the configuration file. (The prompt might include the name or address of a default file server.)
Step 6 Enter the name or IP address of the remote host. In the following example, the name of the remote server is servername:
Step 7 Enter the name of the configuration file. The default is to use the name of the router with the suffix -confg. Press Return to accept the default filename, or enter a different name for the file, then press Return. In the following example, the default is accepted:
Step 8 The system displays the instructions you entered for confirmation. If the instructions are not correct, enter n (no), and then press Return to cancel the process. To accept the instructions, press Return, or press y and then press Return. In the following example, the default is accepted:
The system displays a series of exclamation points
(! ! !) or periods (. . .) during the copy process. The !!!! and [ok] indicate that the operation was successful. A series of periods (...) and [timed out] or [failed] indicates a failure of the process. If the display indicates that the process was successful, the copy process is complete. The configuration is stored on the remote file server.
If the display indicates that the process failed, the configuration was not saved (see the following example):
Repeat the preceding steps, or select a different remote file server and repeat the preceding steps.
After you upload the configuration file, continue with the "Remove and Install an Interface Processor, Filler, VIP, or RSP" section to install the RSP. If you are unable to copy the configuration to a remote host successfully, contact your network administrator or contact Cisco technical assistance.
Retrieve the saved configuration and copy it to NVRAM by accessing the router through a console terminal, or from a remote terminal.
Note The router runs from the default configuration in NVRAM until the previous configuration is retrieved. Passwords configured on the previous system are not valid until they are retrieved.
Step 2 Enter the ping command followed by the name or IP address of the remote server, and then press Return to check the connection between the router and the remote host.
Step 3 Enter the copy tftp startup-config command and press Return to enter the configuration mode and specify that you will configure the system from a network device (instead of from the console terminal, which is the default).
Step 4 Enter the IP address or name of the remote host (the remote TFTP server to which you originally saved the configuration file).
Step 5 Enter the name of the configuration file. The default is to use the name of the router with the suffix -confg (Router-confg in the following example). If you specified a different filename when you copied the configuration, enter the filename; otherwise, press Return to accept the default.
Step 6 Before the system reloads the new configuration file in NVRAM, it displays the instructions you entered for confirmation. If the instructions are not correct, enter n (no), and then press Return to cancel the process. To accept the instructions, press Return, or press y and then press Return. Output similar to the following appears:
The console display indicates whether or not the operation was successful. A series of exclamation points (!!!!) and [OK] (as shown in the preceding example) indicates that the operation was successful. A series of periods (. . .) and [timed out] or [failed] indicates a failure due to a network fault or an incorrect server name, address, or filename. The following is an example of a failed attempt to boot from a remote server:
If the display indicates that the process was successful, as shown in Step 6, proceed to the next step.
If the display indicates that the process failed, verify the name or IP address of the remote server and the filename, and repeat the preceding steps. If the process fails again, contact your network administrator.
Step 7 Enter the show startup-config command to confirm that the configuration file was retrieved correctly. Look at the first line for the configuration file size. Compare it with the file you retrieved from the TFTP server to confirm that it is correct. Following is an example:
Step 8 To ensure that the startup configuration file stored in NVRAM is the default running configuration file used by the system, enter the copy system:running-config nvram:startup-config command:
This completes the process for retrieving the configuration file for the RSP.
Note First remove the VIP from the chassis before removing the port adapter from the VIP. See the "Remove and Install an Interface Processor, Filler, VIP, or RSP" section for instructions.
Step 2 Grasp the handle and carefully pull it out of its slot, away from the edge connector at the rear of the slot. (See A.)
Step 3 To insert the port adapter, align the carrier between the upper and the lower edges of the port adapter slot. (See B.)
Step 4 Carefully slide the port adapter into the slot until the connector is completely seated in the connector at the rear of the port adapter slot, as shown in B.
Step 5 Install the screw in the rear of the port adapter slot on the VIP. Do not overtighten the screw. (See A.)
Step 6 Carefully slide the VIP motherboard into the interface processor slot until the connectors at the rear of the VIP are completely seated in the connectors at the rear of the interface processor slot. Use the ejector levers to seat the VIP in the interface processor slot. Tighten the captive installation screws on the VIP.
(See C.)
Note The following procedure assumes you have already removed the chassis cover panel, the fan tray, the power harness cover, and the power harness. If you have not, refer to the appropriate sections in the Cisco 7500 Series Installation and Configuration Guide for instructions.
| Warning Before working on the chassis or near power supplies, disconnect the power cable on AC units or disconnect the power at the circuit breaker on DC units. |
Step 2 Disconnect the power cable from the power supply.
For the AC-input power supply: Move the cable retention clip away from the power cable and disconnect the power cable from the AC receptacle.
For the DC-input power supply: Use a wire cutter to cut the nylon cable tie that provides strain relief for the DC power cable. (You must replace this nylon cable tie with a new one after the new power supply is installed.) Remove the DC-input cable from the terminal block.
Step 3 Attach an ESD-preventive strap between you and any unpainted chassis surface.
Step 4 Disconnect the power harness plug from the backplane receptacle by pulling the polarized plug out of the receptacle; do not pull on the wires.
Step 5 Use a Number 2 Phillips screwdriver to remove the two M4 x 10-mm Phillips panhead screws that secure the power supply ears (one on each side of the power supply) to the chassis frame.
Step 6 Using both hands, grasp both of the power supply handles and pull the power supply about halfway out of the bay. Then grasp the sides of the power supply and pull it out of the chassis.
Step 2 Use a Number 2 Phillips screwdriver to replace the two M4 x 10-mm Phillips panhead screws to secure the two power supply ears to the chassis frame.
Step 3 Reattach the power harness plug to the backplane receptacle. Ensure that the plug is fully seated in the receptacle.
Step 4 Replace the power harness cover.
Step 5 Replace the fan tray.
Step 6 Replace the cover panel.
Step 7 For AC-input power supplies: On the interface processor side of the power supply, replace the cable retention clip on the AC input port by pinching the sides of the retention clip together and letting the ends of the retention clip snap outward into the holes in the jackscrews.
For DC-input power supplies: To provide strain relief for the DC-input cable, replace the nylon cable tie with a new nylon cable tie.
92782 Issy Les Moulineaux Cedex 9
Cisco Systems Australia, Pty., Ltd
AccessPath, AtmDirector, Browse with Me, CCDA, CCDE, CCDP, CCIE, CCNA, CCNP, CCSI, CD-PAC, CiscoLink, the Cisco NetWorks logo, the Cisco Powered Network logo, Cisco Systems Networking Academy, the Cisco Systems Networking Academy logo, Fast Step, Follow Me Browsing, FormShare, FrameShare, GigaStack, IGX, Internet Quotient, IP/VC, iQ Breakthrough, iQ Expertise, iQ FastTrack, the iQ Logo, iQ Net Readiness Scorecard, MGX, the Networkers logo, Packet, RateMUX, ScriptBuilder, ScriptShare, SlideCast, SMARTnet, TransPath, Unity, Voice LAN, Wavelength Router, and WebViewer are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, Discover All That's Possible, and Empowering the Internet Generation, are service marks of Cisco Systems, Inc.; and Aironet, ASIST, BPX, Catalyst, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, the Cisco IOS logo, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Enterprise/Solver, EtherChannel, EtherSwitch, FastHub, FastSwitch, IOS, IP/TV, LightStream, MICA, Network Registrar, PIX, Post-Routing, Pre-Routing, Registrar, StrataView Plus, Stratm, SwitchProbe, TeleRouter, and VCO are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries.
All other brands, names, or trademarks mentioned in this document or Web site are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0104R)
Cisco Systems has more than 200 offices in the following countries. Addresses, phone numbers, and fax numbers are listed on the
Cisco Connection Online Web site at http://www.cisco.com/go/offices.
Posted: Thu Mar 27 14:05:06 PST 2003
All contents are Copyright © 1992--2002 Cisco Systems, Inc. All rights reserved.
Important Notices and Privacy Statement.
