Table of Contents

Performing a Basic Configuration

Using show Commands to Verify the New Interface Status

Using the show version or show hardware Commands
Using the show diag Command
Using the show interfaces Command

Using the ping Command to Verify Network Connectivity

Configuring the GEIP+

To continue your GEIP+ installation, you must configure the Gigabit Ethernet (GE) interface.

This chapter contains the following sections:

Using the EXEC Command Interpreter

You modify the configuration of your router through the software command interpreter called the EXEC (also called enable mode). You must enter the privileged level of the EXEC command interpreter with the enable command before you can use the configure command to configure a new interface or change the existing configuration of an interface. The system prompts you for a password if one has been set.

The system prompt for the privileged level ends with a pound sign (#) instead of an angle bracket (>). At the console terminal, use the following procedure to enter the privileged level:

Step 2   Enter the password (the password is case sensitive). For security purposes, the password is not displayed.

When you enter the correct password, the system displays the privileged-level system prompt (#):

To configure the new interface, proceed to the "Configuring the Interface" section.

Configuring the Interface

After you verify that the new GEIP+ is installed correctly (the enabled LED goes on), use the privileged-level configure command to configure the new interface. Have the following information available:

If you installed a new GEIP+ or if you want to change the configuration of an existing interface, you must enter configuration mode to configure the new interface. If you replaced a GEIP+ that was previously configured, the system recognizes the new interface and brings it up in its existing configuration.

For a summary of the configuration options available and instructions for configuring the interface on a GEIP+, refer to the appropriate configuration publications listed in the "Related Documentation" section.

You execute configuration commands from the privileged level of the EXEC command interpreter, which usually requires password access. Contact your system administrator, if necessary, to obtain password access. (See the "Using the EXEC Command Interpreter" section for an explanation of the privileged level of the EXEC.)

This section contains the following subsection:

Performing a Basic Configuration

Following are instructions for a basic configuration: enabling an interface and specifying IP routing. You might also need to enter other configuration subcommands, depending on the requirements for your system configuration and the protocols you plan to route on the interface. For complete descriptions of configuration subcommands and the configuration options available for Gigabit Ethernet interfaces, refer to the appropriate software documentation.

In the following procedure, press the Return key after each step unless otherwise noted. At any time you can exit the privileged level and return to the user level by entering disable at the prompt as follows:

Step 2   Specify the first interface to configure by entering the interface gigabitethernet subcommand followed by the interface address of the interface you plan to configure. Table 5-1 provides an example.

Step 3   If IP routing is enabled on the system, you can assign an IP address and subnet mask to the interface with the ip address configuration subcommand, as in the following example:

Step 4   Add any additional configuration subcommands required to enable routing protocols and set the interface characteristics for your configuration requirements.

---

Note    Full-duplex operation is the default for the GEIP+. Half-duplex operation is not supported.

---

Step 5   Reenable the interface using the no shutdown command.

Step 6   After including all the configuration subcommands to complete your configuration, press Ctrl-Z—hold down the Control key while you press Z—or enter end or exit to exit configuration mode.

Step 7   Write the new configuration to NVRAM as follows:

This completes the procedure for creating a basic configuration.

Checking the Configuration

After configuring the new interface, use the show commands to display the status of the new interface and use the ping command to check connectivity. This section includes the following subsections:

Using show Commands to Verify the New Interface Status

Table 5-2 demonstrates how you can use the show commands to verify that the new interface is configured and operating correctly and that the GEIP+ appears in it correctly. Sample displays of the output of selected show commands appear in the sections that follow. For complete command descriptions and examples, refer to the publications listed in the "Related Documentation" section.

Note   The sample output that appears in this document might not match the output that you receive when running the same commands. The sample output in this document is intended only as an example.

If an interface is shut down and you configured it as up, or if the displays indicate that the hardware is not functioning properly, ensure that the interface is properly connected and terminated. If you still have problems bringing up the interface, contact a service representative for assistance. This section includes the following subsections:

Proceed to the "Using the ping Command to Verify Network Connectivity" section when you have finished using the show commands.

Using the show version or show hardware Commands

To display the configuration of the system hardware, the number of each interface type installed, the Cisco IOS software version, the names and sources of configuration files, and the boot images, use the show version (or show hardware) command.

Note   The sample output that appears in this document might not match the output that you receive when running these commands. The sample output in this document is intended only as an example.

GEIP+ in Cisco 7500 Series Routers

Following is an example of the show version command from a Cisco 7500 series router with the GEIP+.

Note   The GEIP+ interface processor shares the same hardware identification information as a versatile interface processor (VIP) 4. Therefore, it is important to note that in the output of the show version command, the GEIP+ appears with a "VIP4-80 RM7000 controller" label shown beside the number of GigabitEthernet interfaces.

Using the show diag Command

To display the types of port adapters and interface processors installed in your system (and specific information about each) use the show diag command.

Note   The sample output that appears in this document might not match the output that you receive when running the same commands. The sample output in this document is intended only as an example.

GEIP+ in Cisco 7500 Series Routers

Following is an example of the show diag command with a GEIP+ in interface processor slot 1.

Note   The GEIP+ interface processor shares the same hardware identification information as a versatile interface processor (VIP) 4. Therefore, it is important to note that in the output of the show diag command, the label "VIP4-80 RM7000 controller" appears. However, the PA Bay output field reflects the dual wide GigabitEthernet interface.

Using the show interfaces Command

The show interfaces command displays status information (including the physical slot and interface address) for the interfaces you specify. The example that follows specifies a Gigabit Ethernet interface.

For complete descriptions of interface subcommands and the configuration options available for GEIP+ interface, refer to the publications listed in the "Related Documentation" section.

Note   The sample output that appears in this document might not match the output that you receive when running the same commands. The sample output in this document is intended only as an example.

GEIP+ in Cisco 7500 Series Routers

Following is an example of the show interfaces command that shows status information specific to the gigabit ethernet interface installed in interface processor slot 2 in a Cisco 7500 series router:

Using the ping Command to Verify Network Connectivity

The packet internet groper (ping) command allows you to verify that an interface port is functioning properly. This section provides a brief description of this command. Refer to the publications listed in the "Related Documentation" section for detailed command descriptions and examples.

The ping command sends echo request packets out to a remote device at an IP address that you specify. After sending an echo request, the system waits a specified time for the remote device to reply. Each echo reply is displayed as an exclamation point (!) on the console terminal; each request that is not returned before the specified timeout is displayed as a period (.). A series of exclamation points (!!!!!) indicates a good connection; a series of periods (.....) or the messages [timed out] or [failed] indicate a bad connection.

Following is an example of a successful ping command to a remote server with the address 10.0.0.10:

If the connection fails, verify that you have the correct IP address for the destination and that the device is active (powered on), and repeat the ping command.

Posted: Fri May 2 09:08:22 PDT 2003
All contents are Copyright © 1992--2002 Cisco Systems, Inc. All rights reserved.
Important Notices and Privacy Statement.