Table 9-1 Command Summary
Command
|
Purpose
|
RP/0/0/CPU0:router(config-sonet)# ais-shut
|
Configures the automatic insertion of a line alarm indication signal (LAIS) in the sent SONET signal whenever the SONET port enters the administrative shutdown state.
|
RP/0/0/CPU0:router(config)# aps group number
|
Adds an APS group with a specified number and enters APS group configuration mode.
|
RP/0/0/CPU0:router(config-aps)# channel {0 | 1}
local {sonet | preconfigure} number
|
Creates a channel for the APS group.
|
RP/0/0/CPU0:router(config-sonet)# clock source
{internal | line}
|
Configures the SONET port TX clock source.
|
RP/0/0/CPU0:router(config-sonet)# commit
|
Saves the configuration changes to the running configuration file and remains within the configuration session.
|
RP/0/0/CPU0:Router# configure
|
Enters global configuration mode.
|
RP/0/0/CPU0:router(config)# controller sonet
number
|
Enters SONET controller configuration submode.
|
RP/0/0/CPU0:router(config-sonet)# delay trigger
line value
|
Configures the SONET port delay trigger line value.
|
RP/0/0/CPU0:router(config-if)# encapsulation [hdlc
| ppp]
|
Configures the interface encapsulation parameters and details such as HDLC or PPP.
|
RP/0/0/CPU0:Router(config-sonet)# end
|
Prompts you to save the configuration changes and exits the configuration session.
|
RP/0/0/CPU0:router(config-sonet)# framing {sdh |
sonet}
|
Configures the controller framing.
|
RP/0/0/CPU0:router(config)# interface loopback
number
|
Configures a loopback interface if a two-router APS is desired and enters interface configuration mode.
|
RP/0/0/CPU0:Router(config)# interface pos number
|
Specifies the POS interface to configure, where number is in the format rack/slot/subslot/port.
|
RP/0/0/CPU0:Router(config-if)# ipv4 address
ip-address mask
or
RP/0/0/CPU0:Router(config-if)# ipv6 address
ipv6-prefix/prefix-length
|
Sets a primary or secondary IP address for an interface.
|
RP/0/0/CPU0:router(config-if)# keepalive [seconds
| disable]
|
Sets the keepalive timer for the channel.
|
RP/0/0/CPU0:router(config-sonet)# loopback
{internal | line}
|
Configures the SONET controller for loopback.
|
RP/0/0/CPU0:Router(config-if)# mtu value
|
Sets the maximum transmission unit (MTU) value for the interface.
|
RP/0/0/CPU0:Router(config-if)# no shutdown
|
Enables an interface.
|
RP/0/0/CPU0:router(config-sonet)# overhead {j0 |
s1s0e} byte-value
|
Configures the controller's overhead.
|
RP/0/0/CPU0:router(config-sonet)# path keyword
values
|
Configures SONET controller path values.
|
RP/0/0/CPU0:router(config-sonet)# path delay
trigger value
|
Configures SONET port delay trigger values in milliseconds.
|
RP/0/0/CPU0:router(config-if)# pos crc {16 | 32}
|
Selects a cyclic redundancy check (CRC) value for the channel.
|
RP/0/0/CPU0:router(config-if)# ppp authentication
protocol list-name
|
Enables Challenge Handshake Authentication Protocol (CHAP), MS-CHAP, or Password Authentication Protocol (PAP) and specifies the order of selection on the interface.
|
RP/0/0/CPU0:router# show controllers sonet number
|
Verifies the SONET controller configuration., where number specifies the interface ID in the format rack/slot/subslot/port.
|
RP/0/0/CPU0:router(config-sonet)# threshold
{b1-tca | b2-tca | sd-ber | sf-ber} bit-error-rate
|
Configures the bit-error rate (BER) threshold values of the specified alarms for a SONET controller.
|
RP/0/0/CPU0:router# show aps
|
Displays operational status for all configured SONET APS groups.
|
RP/0/0/CPU0:router# show aps group [number]
|
Displays operational status for configured SONET APS groups.
|
RP/0/0/CPU0:Router# show interfaces
|
Displays the configured interface and checks the status of each interface port.
|
RP/0/0/CPU0:Router# show running-config
|
Displays the configuration information currently running on the router.
|
