Regulatory Compliance and Safety Information for the Cisco Service Control Engines (SCE)

This is the first version of this document. The document version history is documented in Table 1.

Read this document before installing or servicing the Cisco Service Control Engine (SCE) systems:

Table 1 Document Version History
Document Version	Date	Notes
78-17090-02	June, 2007	Added Statement 371.
78-17090-01	August, 2005	This document contains all the Cisco Service Control Engine platforms regulatory compliance and safety information.

Note Only trained and qualified service personnel (as defined in IEC 60950 and AS/NZS 3260) should install, replace, or service the equipment. Install the system in accordance with the U.S. National Electric Code if you are in the United States.

Warning This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents.

Warning Definition Statement

This section includes translations in multiple languages of the warnings that may appear in your product documents.

Statement 10—Installation Warning


Warning	Read the installation instructions before you connect the system to its power source.
Waarschuwing	Raadpleeg de installatie-aanwijzingen voordat u het systeem met de voeding verbindt.
Varoitus	Lue asennusohjeet ennen j�rjestelm�n yhdist�mist� virtal�hteeseen.
Attention	Avant de brancher le syst�me sur la source d'alimentation, consulter les directives d'installation.
Warnung	Lesen Sie die Installationsanweisungen, bevor Sie das System an die Stromquelle anschlie�en.
Avvertenza	Consultare le istruzioni di installazione prima di collegare il sistema all'alimentatore.
Advarsel	Les installasjonsinstruksjonene f�r systemet kobles til str�mkilden.
Aviso	Leia as instru��es de instala��o antes de ligar o sistema � sua fonte de energia.
�Advertencia!	Ver las instrucciones de instalaci�n antes de conectar el sistema a la red de alimentaci�n.
Varning!	L�s installationsanvisningarna innan du kopplar systemet till dess str�mf�rs�rjningsenhet.

Statement 1040—Product Disposal


Warning	Ultimate disposal of this product should be handled according to all national laws and regulations.
Waarschuwing	Het uiteindelijke wegruimen van dit product dient te geschieden in overeenstemming met alle nationale wetten en reglementen.
Varoitus	T�m� tuote on h�vitett�v� kansallisten lakien ja m��r�ysten mukaisesti.
Attention	La mise au rebut ou le recyclage de ce produit sont g�n�ralement soumis � des lois et/ou directives de respect de l'environnement. Renseignez-vous aupr�s de l'organisme comp�tent.
Warnung	Die Entsorgung dieses Produkts sollte gem�� allen Bestimmungen und Gesetzen des Landes erfolgen.
Avvertenza	Lo smaltimento di questo prodotto deve essere eseguito secondo le leggi e regolazioni locali.
Advarsel	Endelig kassering av dette produktet skal v�re i henhold til alle relevante nasjonale lover og bestemmelser.
Aviso	Deitar fora este produto em conformidade com todas as leis e regulamentos nacionais.
�Advertencia!	Al deshacerse por completo de este producto debe seguir todas las leyes y reglamentos nacionales.
Varning!	Vid deponering hanteras produkten enligt g�llande lagar och best�mmelser.





Aviso	O descarte definitivo deste produto deve estar de acordo com todas as leis e regulamenta��es nacionais.
Advarsel	Endelig bortskaffelse af dette produkt skal ske i henhold til g�ldende love og regler.

Statement 43—Jewelry Removal Warning


Warning Before you work on equipment that is connected to power lines, remove jewelry (including rings, necklaces, and watches). Metal objects will heat up when connected to power and ground and can cause serious burns or weld the metal object to the terminals.
Waarschuwing	Alvorens aan apparatuur te werken die met elektrische leidingen is verbonden, sieraden (inclusief ringen, kettingen en horloges) verwijderen. Metalen voorwerpen worden warm wanneer ze met stroom en aarde zijn verbonden, en kunnen ernstige brandwonden veroorzaken of het metalen voorwerp aan de aansluitklemmen lassen.
Varoitus	Ennen kuin ty�skentelet voimavirtajohtoihin kytkettyjen laitteiden parissa, ota pois kaikki korut (sormukset, kaulakorut ja kellot mukaan lukien). Metalliesineet kuumenevat, kun ne ovat yhteydess� s�hk�virran ja maan kanssa, ja ne voivat aiheuttaa vakavia palovammoja tai hitsata metalliesineet kiinni liit�nt�napoihin.
Attention	Avant d'acc�der � cet �quipement connect� aux lignes �lectriques, �ter tout bijou (anneaux, colliers et montres compris). Lorsqu'ils sont branch�s � l'alimentation et reli�s � la terre, les objets m�talliques chauffent, ce qui peut provoquer des blessures graves ou souder l'objet m�tallique aux bornes.
Warnung	Vor der Arbeit an Ger�ten, die an das Netz angeschlossen sind, jeglichen Schmuck (einschlie�lich Ringe, Ketten und Uhren) abnehmen. Metallgegenst�nde erhitzen sich, wenn sie an das Netz und die Erde angeschlossen werden, und k�nnen schwere Verbrennungen verursachen oder an die Anschlu�klemmen angeschwei�t werden.
Avvertenza	Prima di intervenire su apparecchiature collegate alle linee di alimentazione, togliersi qualsiasi monile (inclusi anelli, collane, braccialetti ed orologi). Gli oggetti metallici si riscaldano quando sono collegati tra punti di alimentazione e massa: possono causare ustioni gravi oppure il metallo pu� saldarsi ai terminali.
Advarsel	Fjern alle smykker (inkludert ringer, halskjeder og klokker) f�r du skal arbeide p� utstyr som er koblet til kraftledninger. Metallgjenstander som er koblet til kraftledninger og jord blir sv�rt varme og kan for�rsake alvorlige brannskader eller smelte fast til polene.
Aviso	Antes de trabalhar em equipamento que esteja ligado a linhas de corrente, retire todas as j�ias que estiver a usar (incluindo an�is, fios e rel�gios). Os objectos met�licos aquecer�o em contacto com a corrente e em contacto com a liga��o � terra, podendo causar queimaduras graves ou ficarem soldados aos terminais.
�Advertencia!	Antes de operar sobre equipos conectados a l�neas de alimentaci�n, quitarse las joyas (incluidos anillos, collares y relojes). Los objetos de metal se calientan cuando se conectan a la alimentaci�n y a tierra, lo que puede ocasionar quemaduras graves o que los objetos met�licos queden soldados a los bornes.
Varning!	Tag av alla smycken (inklusive ringar, halsband och armbandsur) innan du arbetar p� utrustning som �r kopplad till kraftledningar. Metallobjekt hettas upp n�r de kopplas ihop med str�m och jord och kan f�rorsaka allvarliga br�nnskador; metallobjekt kan ocks� sammansvetsas med kontakterna.

Statement 1001—Work During Lightning Activity


Warning	Do not work on the system or connect or disconnect cables during periods of lightning activity.
Waarschuwing	Tijdens onweer dat gepaard gaat met bliksem, dient u niet aan het systeem te werken of kabels aan te sluiten of te ontkoppelen.
Varoitus	�l� ty�skentele j�rjestelm�n parissa �l�k� yhdist� tai irrota kaapeleita ukkosilmalla.
Attention	Ne pas travailler sur le syst�me ni brancher ou d�brancher les c�bles pendant un orage.
Warnung	Arbeiten Sie nicht am System und schlie�en Sie keine Kabel an bzw. trennen Sie keine ab, wenn es gewittert.
Avvertenza	Non lavorare sul sistema o collegare oppure scollegare i cavi durante un temporale con fulmini.
Advarsel	Utf�r aldri arbeid p� systemet, eller koble kabler til eller fra systemet n�r det tordner eller lyner.
Aviso	N�o trabalhe no sistema ou ligue e desligue cabos durante per�odos de mau tempo (trovoada).
�Advertencia!	No operar el sistema ni conectar o desconectar cables durante el transcurso de descargas el�ctricas en la atm�sfera.
Varning!	Vid �ska skall du aldrig utf�ra arbete p� systemet eller ansluta eller koppla loss kablar.

Statement 49—Qualified Personnel Warning

This equipment is to be installed and maintained by service personnel only as defined by AS/NZS 3260 Clause 1.2.14.3 Service Personnel.


Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Waarschuwing	Installatie en reparaties mogen uitsluitend door getraind en bevoegd personeel uitgevoerd worden.
Varoitus	Ainoastaan koulutettu ja p�tev� henkil�kunta saa asentaa tai vaihtaa t�m�n laitteen.
Avertissement	Tout installation ou remplacement de l'appareil doit �tre r�alis� par du personnel qualifi� et comp�tent.
Achtung	Ger�t nur von geschultem, qualifiziertem Personal installieren oder auswechseln lassen.
Avvertenza	Solo personale addestrato e qualificato deve essere autorizzato ad installare o sostituire questo apparecchio.
Advarsel	Kun kvalifisert personell med riktig oppl�ring b�r montere eller bytte ut dette utstyret.
Aviso	Este equipamento dever� ser instalado ou substitu�do apenas por pessoal devidamente treinado e qualificado.
�Atenci�n!	Estos equipos deben ser instalados y reemplazados exclusivamente por personal t�cnico adecuadamente preparado y capacitado.
Varning	Denna utrustning ska endast installeras och bytas ut av utbildad och kvalificerad personal.

Australia SA/NZS 3260 Warning

The colors of the cores in the main leads may not correspond with the colored markings identifying the terminals in the plug if power supply cord rewiring is required. Following are the colors of the main leads of this equipment:

Table 2 Australia SCE Platform Lead Color
Lead Color	Function
Green and Yellow	Earth
Blue	Neutral
Brown	Live

•

The green and yellow colored core must be connected to the terminal in the plug, which is marked with the letter E or by the earth symbol, or colored green and yellow.

•

�The blue core must be connected to the terminal, which is marked with the letter N or colored black.

•

�The brown core must be connected to the terminal, which is marked with the letter L or colored red.

Statement 328—Main Ground Connection Warning

When installing the unit, always make the ground connection first and disconnect it last.


Warning	For Nordic countries (Norway, Finland, Sweden and Denmark) this system must be installed in a Restricted Access Location, where the voltage of the main ground connection of all equipment is the same (equipotential earth) and the system is connected to a grounded electrical outlet.
Waarschuwing	Voor de Noord-Europese landen (Noorwegen, Finland, Zweden en Denemarken) dient dit systeem ge�nstalleerd te worden in een locatie met beperkte toegang, waarbij het voltage van de hoofdaardingsaansluiting van alle apparatuur hetzelfde is (equipotentiale aarding) en het systeem aangesloten is op een geaarde elektrische contactdoos.
Varoitus	Pohjoismaissa (Norja, Ruotsi, Suomi ja Tanska) t�m� j�rjestelm� on asennettava paikkaan, johon on rajoitettu p��sy ja jossa kaikkien laitteiden p��maadoituksen j�nnite on sama (tasapotentiaalinen maa) ja j�rjestelm� on kytketty maadoitettuun pistorasiaan.
Attention	Dans les pays scandinaves (Norv�ge, Finlande, Su�de et Danemark), ce syst�me doit �tre install� dans un local � acc�s restreint, o� le voltage de la prise de terre principale de tous les appareils est le m�me (" terre �quipotentielle ") et o� le syst�me est connect� � une prise �lectrique mise � la terre.
Warnung	In nordischen L�ndern (Norwegen, Finnland, Schweden und D�nemark) muss dieses System an einem Standort mit beschr�nktem Zugang installiert werden, an dem die Spannung der Haupterdungsverbindung aller Ger�te gleich ist (�quipotential-Erdung) und das System an eine geerdete Steckdose angeschlossen ist.
Avvertenza	In Scandinavia (Norvegia, Finlandia, Svezia e Danimarca) questo sistema deve essere installato in un'Area ad Accesso Limitato, in cui il livello di tensione della connessione di terra della rete � lo stesso per tutti gli apparecchi (terra equipotenziale) e il sistema � connesso ad un impianto di messa a terra.
Advarsel	I de nordiske land (Norge, Finland, Sverige og Danmark) m� dette systemet installeres p� et sted merket begrenset adgang, der spenningen i apparatjordforbindelsen for alt utstyr er den samme (ekvipotensial jord) og der systemet er koblet til et jordet elektrisk uttak.
Aviso	Para pa�ses N�rdicos (Noruega, Finl�ndia, Su�cia e Dinamarca) este sistema deve ser instalado em um local de acesso restrito onde a voltagem do aterramento principal de todos os equipamento � o mesmo (equipotential earth) e o sistema est� conectado a uma tomada el�trica aterrada.
�Advertencia!	En los pa�ses n�rdicos (Noruega, Finlandia, Suecia y Dinamarca), este sistema debe ser instalado en una ubicaci�n de acceso restringido donde el voltaje de la conexi�n principal a tierra de todo el equipamiento sea el mismo (tierra equipotencial) y el sistema se conecte a un enchufe con descarga a tierra.
Varning!	I de nordiska l�nderna (Norge, Finland, Sverige och Danmark) m�ste detta system installeras p� en plats med begr�nsad �tkomst, d�r sp�nningen i huvudjordningsanslutningen f�r all utrustning �r densamma (ekvipotentiell jordning) och d�r systemet �r anslutet till ett jordat eluttag.

Statement 39—Grounded Equipment Warning


Warning	This equipment is intended to be grounded. Ensure that the host is connected to earth ground during normal use.
Waarschuwing	Deze apparatuur hoort geaard te worden Zorg dat de host-computer tijdens normaal gebruik met aarde is verbonden.
Varoitus	T�m� laitteisto on tarkoitettu maadoitettavaksi. Varmista, ett� is�nt�laite on yhdistetty maahan normaalik�yt�n aikana.
Attention	Cet �quipement doit �tre reli� � la terre. S'assurer que l'appareil h�te est reli� � la terre lors de l'utilisation normale.
Warnung	Dieses Ger�t mu� geerdet werden. Stellen Sie sicher, da� das Host-Ger�t w�hrend des normalen Betriebs an Erde gelegt ist.
Figyelem!	A k�sz�l�ket v�d�f�ldel�ssel kell ell�tni. Gy�z�dj�n meg r�la, hogy a k�sz�l�k norm�l haszn�lat sor�n csatlakozik a f�ldh�z.
Avvertenza	Questa apparecchiatura deve essere collegata a massa. Accertarsi che il dispositivo host sia collegato alla massa di terra durante il normale utilizzo.
Advarsel	Dette utstyret skal jordes. Forviss deg om vertsterminalen er jordet ved normalt bruk.
Aviso	Este equipamento dever� estar ligado � terra. Certifique-se que o host se encontra ligado � terra durante a sua utiliza��o normal.
�Advertencia!	Este equipo debe conectarse a tierra. Asegurarse de que el equipo principal est� conectado a tierra durante el uso normal.
Varning!	Denna utrustning �r avsedd att jordas. Se till att v�rdenheten �r jordad vid normal anv�ndning.

Statement 190—Grounding Requirement Warning

This equipment is Class 1 type and must be permanently earthed for protection and functional purposes. For safe operation and servicing, install the AC socket outlet near the equipment so that it is readily accessible .Use the appropriate AC power cord and plug, as required by national standards. This equipment must be permanently earthed.


Warning	This equipment needs to be grounded. Use a green and yellow 14 AWG ground wire to connect the host to earth ground during normal use.
Waarschuwing	Deze apparatuur hoort geaard te woden. Gebruik een groen/gele 14 AWG aarddraad om de host tijdens normaal gebruik met de aarde te verbinden.
Varoitus	T�m� laitteisto t�ytyy maadoittaa. Yhdist� is�nt�laite maahan normaalik�yt�n aikana k�ytt�m�ll� vihre�-keltaista 14 AWG -maadoitusjohtoa.
Attention	Cet �quipement doit �tre reli� � la terre. Utilisez un fil vert et jaune de gabarit 14 (AWG) pour connecter l'h�te � la terre lors son utilisation normale.
Warnung	Dieses Ger�t mu� geerdet werden. Verwenden Sie ein gr�n/gelbes 14-AWG-Erdungskabel, um damit das Host-Ger�t w�hrend des normalen Betriebs zu erden.
Figyelem!	A k�sz�l�ket v�d�f�ldel�ssel kell ell�tni. A k�sz�l�ket norm�l haszn�lat eset�n z�ld �s s�rga 14 AWG jel� f�ldel�vezet�kkel k�sse a f�ldponthoz.
Avvertenza	Questa apparecchiatura deve essere collegata a massa. Durante l'uso normale, collegare l'host alla massa di terra usando un filo di massa verde e giallo di diametro pari a 14 AWG.
Advarsel	Dette utstyret m� jordes. Bruk en gr�nn og gul 14 AWG jordledning til � kople vertsterminalen til jording i l�pet av normalt bruk.
Aviso	� necess�rio que este equipamento esteja ligado � terra. Utilize um fio de liga��o � terra de 14 AWG, verde e amarelo, para ligar o host � liga��o � terra durante a sua utiliza��o normal.
Advertencia	Este equipo debe conectarse a tierra. Utilizar un hilo de puesta a tierra 14 AWG verde y amarillo para conectar a tierra el equipo principal durante el uso normal.
Varning!	Denna utrustning �r avsedd att jordas. Anv�nd en gulgr�n jordledning av storlek 14 AWG till att jorda v�rdenheten vid normal anv�ndning.

Protective Earth Warning

Warning Protective earth is referred to as chassis ground in this document. To make protective earth connection, use the two-hole compression lug grounding points on the back panel.

Statement 93—Ground Conductor Warning


Warning Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available.
Waarschuwing	De aardingsleiding mag nooit buiten werking gesteld worden en de apparatuur mag nooit bediend worden zonder dat er een op de juiste wijze ge�nstalleerde aardingsleiding aanwezig is. Neem contact op met de bevoegde instantie voor elektrische inspecties of met een elektricien als u er niet zeker van bent dat er voor passende aarding gezorgd is.
Varoitus	�l� koskaan ohita maajohdinta tai k�yt� laitteita ilman oikein asennettua maajohdinta. Ota yhteytt� asianmukaiseen s�hk�tarkastusviranomaiseen tai s�hk�asentajaan, jos olet ep�varma maadoituksen sopivuudesta.
Attention	Ne jamais rendre inop�rant le conducteur de masse ni utiliser l'�quipement sans un conducteur de masse ad�quatement install�. En cas de doute sur la mise � la masse appropri�e disponible, s'adresser � l'organisme responsable de la s�curit� �lectrique ou � un �lectricien.
Warnung	Auf keinen Fall den Erdungsleiter unwirksam machen oder das Ger�t ohne einen sachgerecht installierten Erdungsleiter verwenden. Wenn Sie sich nicht sicher sind, ob eine sachgerechte Erdung vorhanden ist, wenden Sie sich an den zust�ndigen elektrischen Fachmann oder einen Elektriker.
Avvertenza	Non escludere mai il conduttore di protezione n� usare l'apparecchiatura in assenza di un conduttore di protezione installato in modo corretto. Se non si sa con certezza che � disponibile un collegamento di messa a terra adeguato, esaminare le Norme CEI pertinenti o rivolgersi a un elettricista qualificato.
Advarsel	Omg� aldri jordingslederen og bruk aldri utstyret uten riktig montert jordingsleder. Ta kontakt med det riktige organet for elektrisk inspeksjon eller en elektriker hvis du er usikker p� om det finnes velegnet jording.
Aviso	Nunca anule o condutor � terra nem opere o equipamento sem ter um condutor � terra adequadamente instalado. Em caso de d�vida em rela��o ao sistema de liga��o � terra, contacte os servi�os locais de inspec��o el�ctrica ou um electricista qualificado.
�Advertencia!	No inhabilitar nunca el conductor de tierra ni hacer funcionar el equipo si no existe un conductor de tierra instalado correctamente. P�ngase en contacto con una autoridad apropiada de inspecci�n el�ctrica o con un electricista competente si no est� seguro de que hay una conexi�n a tierra adecuada.
Varning!	Koppla aldrig fr�n jordledningen och anv�nd aldrig utrustningen utan en p� l�mpligt s�tt installerad jordledning. Om det f�religger os�kerhet huruvida l�mplig jordning finns skall elektrisk besiktningsauktoritet eller elektriker kontaktas.

FCC Warning

Warning This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Restricted Area Warning (DC platform only)

Warning This unit is intended for installation in restricted access areas. A restricted access area is where access can only be gained by service personnel through the use of a special tool, lock and key, or other means of security, and is controlled by the authority responsible for the location.

Statement 94—Wrist Strap Warning


Warning	During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself.
Waarschuwing	Draag tijdens deze procedure aardingspolsbanden om te vermijden dat de kaart beschadigd wordt door elektrostatische ontlading. Raak het achterbord niet rechtstreeks aan met uw hand of met een metalen werktuig, omdat u anders een elektrische schok zou kunnen oplopen.
Varoitus	K�yt� t�m�n toimenpiteen aikana maadoitettuja rannesuojia est��ksesi kortin vaurioitumisen s�hk�staattisen purkauksen vuoksi. �l� kosketa taustalevy� suoraan k�dell�si tai metallisella ty�kalulla s�hk�iskuvaaran takia.
Attention	Lors de cette proc�dure, toujours porter des bracelets antistatiques pour �viter que des d�charges �lectriques n'endommagent la carte. Pour �viter l'�lectrocution, ne pas toucher le fond de panier directement avec la main ni avec un outil m�tallique.
Warnung	Zur Vermeidung einer Besch�digung der Karte durch elektrostatische Entladung w�hrend dieses Verfahrens ein Erdungsband am Handgelenk tragen. Bei Ber�hrung der R�ckwand mit der Hand oder einem metallenen Werkzeug besteht Elektroschockgefahr.
Figyelem!	Az elektromos kis�l�s okozta meghib�sod�s elker�l�se �rdek�ben az elj�r�s sor�n viseljen f�ldel� csukl�p�ntot. Se k�zzel, se f�m eszk�zzel ne �rjen hozz� a k�rtya h�tlapj�hoz, mert k�l�nben �ram�t�st szenvedhet.
Avvertenza	Durante questa procedura, indossare bracciali antistatici per evitare danni alla scheda causati da un'eventuale scarica elettrostatica. Non toccare direttamente il pannello delle connessioni, n� con le mani n� con un qualsiasi utensile metallico, perch� esiste il pericolo di folgorazione.
Advarsel	Bruk jordingsarmb�nd under prosedyren for � unng� ESD-skader p� kortet. Unng� direkte ber�ring av bakplanet med h�nden eller metallverkt�y, slik at di ikke f�r elektrisk st�t.
Aviso	Durante este procedimento e para evitar danos ESD causados � placa, use fitas de liga��o � terra para os pulsos. Para evitar o risco de choque el�ctrico, n�o toque directamente na parte posterior com a m�o ou com qualquer ferramenta met�lica.
�Advertencia!	Usartiras conectadas a tierra en las mu�ecas durante este procedimiento para evitar da�os en la tarjeta causados por descargas electrost�ticas. No tocar el plano posterior con las manos ni con ninguna herramienta met�lica, ya que podr�a producir un choque el�ctrico.
Varning!	Anv�nd jordade armbandsremmar under denna procedur f�r att f�rhindra elektrostatisk skada p� kortet. R�r inte vid baksidan med handen eller metallverktyg d� detta kan orsaka elektrisk st�t.

Statement 1—Power Disconnection Warning


Warning	Before working on a system that has an on/off switch, turn OFF the power and unplug the power cord.
Waarschuwing	Voordat u aan een systeem werkt dat een aan/uit schakelaar heeft, dient u de stroomvoorziening UIT te schakelen en de stekker van het netsnoer uit het stopcontact te halen.
Varoitus	Ennen kuin teet mit��n sellaiselle j�rjestelm�lle, jossa on kaksiasentokytkin, katkaise siit� virta ja kytke virtajohto irti.
Attention	Avant de travailler sur un syst�me �quip� d'un commutateur marche-arr�t, mettre l'appareil � l'arr�t (OFF) et d�brancher le cordon d'alimentation.
Warnung	Bevor Sie an einem System mit Ein/Aus-Schalter arbeiten, schalten Sie das System AUS und ziehen das Netzkabel aus der Steckdose.
Figyelem!	Ha olyan k�sz�l�ken dolgozik, amelynek van ki/bekapcsol� gombja, kapcsolja KI a k�sz�l�ket, �s h�zza ki a t�pk�belt.
Avvertenza	Prima di lavorare su un sistema dotato di un interruttore on/off, spegnere (OFF) il sistema e staccare il cavo dell'alimentazione.
Advarsel	Sl� AV str�mmen og trekk ut str�mledningen f�r det utf�res arbeid p� et system som er utstyrt med en av/p�-bryter.
Aviso	Antes de come�ar a trabalhar num sistema que tem um interruptor on/off, DESLIGUE a corrente el�ctrica e retire o cabo de alimenta��o da tomada.
�Advertencia!	Antes de utilizar cualquier sistema equipado con interruptor de Encendido/Apagado (ON/OFF), cortar la alimentaci�n y desenchufar el cable de alimentaci�n.
Varning!	Sl� AV str�mmen och dra ur n�tsladden innan du utf�r arbete p� ett system med str�mbrytare.

Statement 4—Power Supply Warning


Warning	Do not touch the power supply when the power cord is connected. For systems with a power switch, line voltages are present within the power supply even when the power switch is off and the power cord is connected. For systems without a power switch, line voltages are present within the power supply when the power cord is connected.
Waarschuwing	U dient de voeding niet aan te raken zolang het netsnoer aangesloten is. Bij systemen met een stroomschakelaar zijn er lijnspanningen aanwezig in de voeding, zelfs wanneer de stroomschakelaar uitgeschakeld is en het netsnoer aangesloten is. Bij systemen zonder een stroomschakelaar zijn er lijnspanningen aanwezig in de voeding wanneer het netsnoer aangesloten is.
Varoitus	�l� kosketa virtal�hdett� virtajohdon ollessa kytkettyn�. Virrankatkaisimella varustetuissa j�rjestelmiss� on virtal�hteen sis�ll� j�ljell� verkkoj�nnite, vaikka virrankatkaisin on katkaistu-asennossa virtajohdon ollessa kytkettyn�. J�rjestelmiss�, joissa ei ole virrankatkaisinta, on virtal�hteen sis�ll� verkkoj�nnite, kun virtajohto on kytkettyn�.
Attention	Ne pas toucher le bloc d'alimentation quand le cordon d'alimentation est branch�. Avec les syst�mes munis d'un commutateur marche-arr�t, des tensions de ligne sont pr�sentes dans l'alimentation quand le cordon est branch�, m�me si le commutateur est � l'arr�t. Avec les syst�mes sans commutateur marche-arr�t, l'alimentation est sous tension quand le cordon d'alimentation est branch�.
Warnung	Ber�hren Sie das Netzger�t nicht, wenn das Netzkabel angeschlossen ist. Bei Systemen mit Netzschalter liegen Leitungsspannungen im Netzger�t vor, wenn das Netzkabel angeschlossen ist, auch wenn das System ausgeschaltet ist. Bei Systemen ohne Netzschalter liegen Leitungsspannungen im Netzger�t vor, wenn das Netzkabel angeschlossen ist.
Figyelem!	Ha a t�pk�bel csatlakoztatva van, ne �rjen hozz� a t�pegys�ghez. Az olyan k�sz�l�kekn�l, amelyeknek van ki/bekapcsol� gombja, a h�l�zati fesz�lts�g akkor is jelen van a t�pegys�gben, ha a k�sz�l�k ki van kapcsolva, de a t�pk�bel csatlakoztatva van. Az olyan k�sz�l�kekn�l, amelyeknek nincs ki/bekapcsol� gombja, a h�l�zati fesz�lts�g akkor van jelen a t�pegys�gben, ha a t�pk�bel csatlakoztatva van.
Avvertenza	Non toccare l'alimentatore se il cavo dell'alimentazione � collegato. Per i sistemi con un interruttore di alimentazione, tensioni di linea sono presenti all'interno dell'alimentatore anche quando l'interruttore di alimentazione � en posizione di disattivazione (off), se il cavo dell'alimentazione � collegato. Per i sistemi senza un interruttore, tensioni di linea sono presenti all'interno dell'alimentatore quando il cavo di alimentazione � collegato.
Advarsel	Ber�r ikke str�mforsyningsenheten n�r str�mledningen er tilkoblet. I systemer som har en str�mbryter, er det spenning i str�mforsyningsenheten selv om str�mbryteren er sl�tt av og str�mledningen er tilkoblet. N�r det gjelder systemer uten en str�mbryter, er det spenning i str�mforsyningsenheten n�r str�mledingen er tilkoblet.
Aviso	N�o toque na unidade abastecedora de energia quando o cabo de alimenta��o estiver ligado. Em sistemas com interruptor, a corrente el�ctrica estar� presente na unidade abastecedora, sempre que o cabo de alimenta��o de energia estiver ligado, mesmo quando o interruptor se encontrar desligado. Para sistemas sem interruptor, a tens�o el�ctrica dentro da unidade abastecedora s� estar� presente quando o cabo de alimenta��o estiver ligado.
�Advertencia!	No tocar la fuente de alimentaci�n mientras el cable est� enchufado. En sistemas con interruptor de alimentaci�n, hay voltajes de l�nea dentro de la fuente, incluso cuando el interruptor est� en Apagado (OFF) y el cable de alimentaci�n enchufado. En sistemas sin interruptor de alimentaci�n, hay voltajes de l�nea en la fuente cuando el cable est� enchufado.
Varning!	Vidr�r inte str�mf�rs�rjningsenheten n�r n�tsladden �r ansluten. F�r system med str�mbrytare finns det n�tsp�nning i str�mf�rs�rjningsenheten �ven n�r str�mmen har slagits av men n�tsladden �r ansluten. F�r system utan str�mbrytare finns det n�tsp�nning i str�mf�rs�rjningsenheten n�r n�tsladden �r ansluten.

Power Compatibility Warning

Warning Never install an AC power module and a DC power module in the same chassis.

Statement 12—Power Supply Disconnection Warning

Warning This unit may have more than one power supply cord. Disconnect all power supply cords before servicing to avoid electric shock.


Warning	Before working on a chassis or working near power supplies, unplug the power cord on AC units; disconnect the power at the circuit breaker on DC units.
Waarschuwing	Voordat u aan een frame of in de nabijheid van voedingen werkt, dient u bij wisselstroom toestellen de stekker van het netsnoer uit het stopcontact te halen; voor gelijkstroom toestellen dient u de stroom uit te schakelen bij de stroomverbreker.
Varoitus	Kytke irti vaihtovirtalaitteiden virtajohto ja katkaise tasavirtalaitteiden virta suojakytkimell�, ennen kuin teet mit��n asennuspohjalle tai ty�skentelet virtal�hteiden l�heisyydess�.
Attention	Avant de travailler sur un ch�ssis ou � proximit� d'une alimentation �lectrique, d�brancher le cordon d'alimentation des unit�s en courant alternatif ; couper l'alimentation des unit�s en courant continu au niveau du disjoncteur.
Warnung	Bevor Sie an einem Chassis oder in der N�he von Netzger�ten arbeiten, ziehen Sie bei Wechselstromeinheiten das Netzkabel ab bzw. schalten Sie bei Gleichstromeinheiten den Strom am Unterbrecher ab.
Figyelem!	Miel�tt elkezdene dolgozni a h�zon vagy t�pegys�gek k�zel�ben, h�zza ki a v�lt��ram� k�sz�l�kek t�pk�bel�t; egyen�ram� k�sz�l�k eset�n szak�tsa meg az �ramot az �rammegszak�t�n�l
Avvertenza	Prima di lavorare su un telaio o intorno ad alimentatori, scollegare il cavo di alimentazione sulle unit� CA; scollegare l'alimentazione all'interruttore automatico sulle unit� CC.
Advarsel	F�r det utf�res arbeid p� kabinettet eller det arbeides i n�rheten av str�mforsyningsenheter, skal str�mledningen trekkes ut p� vekselstr�msenheter og str�mmen kobles fra ved str�mbryteren p� likestr�msenheter.
Aviso	Antes de trabalhar num chassis, ou antes de trabalhar perto de unidades de fornecimento de energia, desligue o cabo de alimenta��o nas unidades de corrente alternada; desligue a corrente no disjuntor nas unidades de corrente cont�nua.
�Advertencia!	Antes de manipular el chasis de un equipo o trabajar cerca de una fuente de alimentaci�n, desenchufar el cable de alimentaci�n en los equipos de corriente alterna (CA); cortar la alimentaci�n desde el interruptor autom�tico en los equipos de corriente continua (CC).
Varning!	Innan du arbetar med ett chassi eller n�ra str�mf�rs�rjningsenheter skall du f�r v�xelstr�msenheter dra ur n�tsladden och f�r likstr�msenheter bryta str�mmen vid �versp�nningsskyddet.

Statement 264—Power Module Warning


Warning	Never install an AC power module and a DC power module in the same chassis.
Waarschuwing	Een voedingsmodule met wisselstroom mag nooit samen met een gelijkstroomvoedingsmodule in het chassis ge�nstalleerd worden.
Varoitus	�l� koskaan asenna vaihtos�hk�tehomoduulia ja tasas�hk�tehomoduulia samaan asennuspohjaan.
Attention	N'installez jamais un module d'alimentation AC et un module d'alimentation DC dans le m�me ch�ssis.
Warnung	Ein Wechelstromsmodul und ein Gleichstrommodul d�rfen niemals in demselben Chassis installiert werden.
Avvertenza	Non installare un modulo di alimentazione in corrente alternata e un modulo di alimentazione in corrente continua nello stesso chassis.
Advarsel	En vekselstr�mmodul og en likestr�mmodul m� aldri installeres i samme chassis.
Aviso	Nunca instale um modulo de corrente CA (corrente alternada) e um modulo CC (corrente cont�nua) no mesmo chassis.
�Advertencia!	Nunca instale un m�dulo de potencia de corriente alterna (CA) en un m�dulo de potencia de corriente continua (CC) en el mismo chasis.
Varning!	Installera aldrig en v�xelstr�ms- och en likstr�mskraftenhet i samma chassi.

Statement 140—Chassis Power Connection


Warning	Before connecting or disconnecting ground or power wires to the chassis, ensure that power is removed from the DC circuit. To ensure that all power is OFF, locate the circuit breaker on the panel board that services the DC circuit, switch the circuit breaker to the OFF position, and tape the switch handle of the circuit breaker in the OFF position.
Waarschuwing	Voordat u aarddraden of elektriciteitsdraden op het frame aansluit of van het frame neemt, dient u te controleren of de stroom naar het gelijkstroomcircuit uitgeschakeld is. Om u ervan te verzekeren dat alle stroom UIT is geschakeld, kiest u op het schakelbord de stroomverbreker die het gelijkstroomcircuit bedient, draait de stroomverbreker naar de UIT positie en plakt de schakelaarhendel van de stroomverbreker met plakband in de UIT positie vast.
Varoitus	Varmista, ett� tasavirtapiiriss� ei ole virtaa ennen maadoitus- tai virtajohtojen kytkemist� asennuspohjaan tai ennen niiden irrottamista. Varmistaaksesi, ett� virta on KATKAISTU t�ysin, paikanna tasavirrasta huolehtivassa kojetaulussa sijaitseva suojakytkin, k��nn� suojakytkin KATKAISTU-asentoon ja teippaa suojakytkimen varsi niin, ett� se pysyy KATKAISTU-asennossa.
Attention	Avant de connecter ou de d�connecter les c�bles d'alimentation (p�les et terre) du ch�ssis, v�rifiez que le circuit de courant continu est hors tension : localisez le disjoncteur sur le panneau de commande du circuit de courant continu, poussez-le sur la position ferm�e (OFF) et, � l'aide d'un ruban adh�sif, bloquez sa poign�e sur cette position.
Warnung	Gleichstrom-Unterbrechung Bevor Sie Erdungs- oder Stromkabel an das Chassis anschlie�en oder von ihm abtrennen, ist sicherzustellen, da� der Gleichstrom-Stromkreis unterbrochen ist. Um sicherzustellen, da� s�mtlicher Strom AUS ist, machen Sie auf der Schalttafel den Unterbrecher f�r die Gleichstromschaltung ausfindig, stellen Sie den Unterbrecher auf OFF, und kleben Sie den Schaltergriff des Unterbrechers mit Klebeband in der AUS-Stellung fest.
Figyelem!	Miel�tt a f�ld- vagy a f�zisvezet�ket a h�zhoz csatlakoztatja, felt�tlen�l szak�tsa meg az egyen�ram� �ramk�r t�pell�t�s�t. �gy gondoskodhat arr�l, hogy mindenf�le t�pell�t�s meg legyen szak�tva, hogy megkeresi az �rammegszak�t�t az egyen�ram� �ramk�rt kiszolg�l� k�rty�n, az �rammegszak�t�t OFF (KI) helyzetbe �ll�tja, �s �rammegszak�t� kapcsol�j�t az OFF (KI) helyzetben leragasztja.
Avvertenza	Prima di collegare o distaccare i cavi elettrici o di messa a terra dallo chassis, assicuratevi che il circuito DC non sia alimentato. Per verificare che tutta l'alimentazione sia scollegata (OFF), individuare l'interruttore automatico sul quadro strumenti che alimenta il circuito CC, mettere l'interruttore in posizione OFF e fissarlo con nastro adesivo in tale posizione.
Advarsel	F�r til- eller frakobling av jord- og str�mledninger til kabinettet, kontroller at str�mmen er frakoblet likestr�mkretsen. S�rg for at all str�m er sl�tt AV. Dette gj�res ved � lokalisere str�mbryteren p� brytertavlen som betjener likestr�mkretsen, sl� str�mbryteren AV og teipe bryterh�ndtaket p� str�mbryteren i AV-stilling.
Aviso	Antes de conectar ou desconectar a liga��o � terra ou a alimenta��o do chassis, certifique-se de que desligou a fonte de alimenta��o de energia do circuito de corrente cont�nua. Para se assegurar que toda a corrente foi DESLIGADA, localize o disjuntor no painel que serve o circuito de corrente cont�nua e coloque-o na posi��o OFF (Desligado), segurando nessa posi��o a manivela do interruptor do disjuntor com fita isoladora.
�Advertencia!	Antes de conectar o desconectar el circuito de tierra o de alimentaci�n del chasis, aseg�rese que la alimentaci�n del circuito CC est� cortada (OFF). Para asegurarse de que toda la alimentaci�n est� cortada (OFF), localice el interruptor autom�tico en el panel que alimenta el circuito de corriente continua, cambie el interruptor autom�tico a la posici�n de apagado (OFF) y sujete con cinta la palanca del interruptor autom�tico en posici�n de apagado (OFF).
Varning!	Innan du kopplar jord- eller elledningar till eller fr�n chassit m�ste du kontrollera att str�mf�rs�rjningen till likstr�mskretsen �r bruten. Kontrollera att all str�mf�rs�rjning �r BRUTEN genom att sl� AV det �versp�nningsskydd som skyddar likstr�mskretsen och tejpa fast �versp�nningsskyddets omkopplare i FR�N-l�get.

Statement 22—SELV Circuit Warning

Warning To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telephone-network voltage (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain TNV circuits. Some LAN and WAN ports both use RJ-45 connectors. Use caution when connecting cables.


Warning	The ports labeled "Ethernet," "10BaseT," "Token Ring," "Console," and "AUX" are safety extra-low voltage (SELV) circuits. SELV circuits should only be connected to other SELV circuits. Because the BRI circuits are treated like telephone-network voltage, avoid connecting the SELV circuit to the telephone network voltage (TNV) circuits.
Waarschuwing	De poorten die "Ethernet", "10BaseT", "Token Ring", "Console" en "AUX" zijn gelabeld, zijn veiligheidscircuits met extra lage spanning (genaamd SELV = Safety Extra-Low Voltage). SELV-circuits mogen alleen met andere SELV-circuits verbonden worden. Omdat de BRI-circuits op dezelfde manier als telefoonnetwerkspanning behandeld worden, mag u het SELV-circuit niet verbinden met de telefoonnetwerkspanning (TNV) circuits.
Varoitus	Portit, joissa on nimet "Ethernet", "10BaseT", "Token Ring", "Console" ja "AUX", ovat erityisen pienen j�nnityksen omaavia turvallisuuspiirej� (SELV-piirej�). T�llaiset SELV-piirit tulee yhdist�� ainoastaan muihin SELV-piireihin. Koska perusluokan liit�nt�jen (Basic Rate Interface- eli BRI-liit�nn�t) j�nnite vastaa puhelinverkoston j�nnitett�, v�lt� SELV-piirin yhdist�mist� puhelinverkoston j�nnitepiireihin (TNV-piireihin).
Attention	Les ports �tiquet�s � Ethernet �, � 10BaseT �, � Token Ring �, � Console � et � AUX � sont des circuits de s�curit� basse tension (Safety Extra-Low Voltage ou SELV). Les circuits SELV ne doivent �tre interconnect�s qu'avec d'autres circuits SELV. Comme les circuits BRI sont consid�r�s comme des sources de tension de r�seau t�l�phonique, �viter de connecter un circuit SELV � un circuit de tension de r�seau t�l�phonique (telephone network voltage ou TNV).
Warnung	Die mit "Ethernet", "10BaseT", "Token Ring", "Console" und "AUX" beschrifteten Buchsen sind Sicherheitskreise mit Sicherheitskleinspannung (Safety Extra-Low Voltage, SELV). SELV-Kreise sollten ausschlie�lich an andere SELV-Kreise angeschlossen werden. Da die BRI-Kreise wie Telefonnetzspannungen behandelt werden, ist der SELV-Kreis nicht an Telefonnetzspannungskreise (TNV) anzuschlie�en.
Avvertenza	Le porte contrassegnate da "Ethernet", "10BaseT", "TokenRing", "Console" e "AUX" sono circuiti di sicurezza con tensione molto bassa (SELV). I circuiti SELV devono essere collegati solo ad altri circuiti SELV. Dato che i circuiti BRI vengono trattati come tensioni di rete telefonica, evitare di collegare il circuito SELV ai circuiti in cui � presente le tensione di rete telefonica (TNV).
Advarsel	Utgangene merket "Ethernet", "10BaseT", "Token Ring", "Console" og "AUX" er lavspentkretser (SELV) for ekstra sikkerhet. SELV-kretser skal kun kobles til andre SELV-kretser. Fordi BRI-kretsene h�ndteres som telenettspenning, unng� � koble SELV-kretsen til kretser for telenettspenning (TNV).
Aviso	As portas "Ethernet", "10BaseT", "Token Ring", "Console", and "AUX" s�o circuitos de seguran�a de baixa tens�o (SELV). Estes circuitos dever�o ser apenas ligados a outros circuitos SELV. Devido ao facto de os circuitos BRI (Interface de Ritmo B�sico) serem tratados como sendo de tens�o equivalente � da rede telef�nica, evite ligar o circuito SELV aos circuitos TNV (tens�o de rede telef�nica).
�Advertencia!	Los puertos "Ethernet", "10BaseT", "Token Ring", "Console" y "AUX" son circuitos de muy baja se�al que garantizan ausencia de peligro (Safety Extra-Low Voltage = SELV). Estos circuitos SELV deben ser conectados exclusivamente con otros tambi�n de tipo SELV. Puesto que los circuitos tipo BRI se comportan como aqu�llos con voltajes de red telef�nica, debe evitarse conectar circuitos SELV con circuitos de voltaje de red telef�nica (TNV).
Varning!	De portar som �r m�rkta "Ethernet", "10BaseT", "Token Ring", "Console" och "AUX" �r SELV-kretsar, d.v.s. skyddskretsar med extra l�g sp�nning (SELV: Safety Extra-Low Voltage = skyddsklensp�nning). SELV-kretsar f�r endast anslutas till andra SELV-kretsar. Eftersom BRI-kretsar behandlas liksom telefonn�tssp�nning b�r SELV-kretsen inte anslutas till telefonn�tssp�nningskretsar (TNV-kretsar).

Statement 116—WAN Port Static Shock Warning


Warning	Hazardous network voltages are present in WAN ports regardless of whether power to the unit is OFF or ON. To avoid electric shock, use caution when working near WAN ports. When detaching cables, detach the end away from the unit first.
Waarschuwing	Er is gevaarlijke netwerkspanning aanwezig in WAN poorten ongeacht of de stroom naar de router INGESCHAKELD of UITGESCHAKELD is. Om elektrische schokken te vermijden, dient u voorzichtig te werk te gaan wanneer u in de nabijheid van WAN poorten werkt. Wanneer u kabels losmaakt, dient u eerst het uiteinde dat zich het verst van de eenheid vandaan bevindt, te verwijderen.
Varoitus	WAN-porteissa on vaarallisia verkkoj�nnitteit� riippumatta siit�, onko yksik�n virta kytketty vai ei. V�ltty�ksesi s�hk�iskulta ole varovainen ty�skennelless�si WAN-porttien l�hettyvill�. Kun irrotat kaapeleita, irrota yksik�st� kauimpana sijaitseva p�� ensiksi.
Attention	Les ports de r�seau longue distance (WAN) g�rent des tensions de r�seau dangereuses, que l'unit� soit sous tension ou pas. Pour �viter tout risque d'�lectrocution, prenez toutes les pr�cautions n�cessaires avant de travailler � proximit� des ports WAN. Pour d�connecter les c�bles, commencez par d�brancher l'extr�mit� la plus �loign�e du routeur.
Warnung	In WAN-Ports sind gef�hrliche Netzspannungen vorhanden, auch wenn der Strom zur Einheit abgeschaltet wurde. Zur Vermeidung von Elektroschock Vorsicht bei der Arbeit in der N�he von WAN-Ports. Beim Abtrennen von Kabeln zuerst das vom Router entfernte Ende l�sen.
Avvertenza	Nelle porte WAN sono presenti tensioni di rete pericolose, sia che il sistema sia acceso o meno (ON od OFF). Per evitare scosse elettriche, fare attenzione quando si lavora in prossimit� di porte WAN. Quando si scollegano cavi, staccare per primo il connettore collegato al router.
Advarsel!	Det er livsfarlig nettverksspenning i WAN-utganger, uavhengig av om str�mmen til enheten er sl�tt av (OFF) eller p� (ON). V�r forsiktig n�r du jobber n�r WAN-utganger slik at du unng�r elektrisk st�t. Hvis du skal l�sne kabler, m� du f�rst l�sne den enden som er lengst borte fra fordelingsenheten.
Aviso	Existem sempre tens�es de rede perigosas nas portas WAN, independentemente da corrente para a unidade estar desligada (OFF) ou ligada (ON). Para evitar choques el�ctricos, tenha o devido cuidado ao trabalhar junto das portas WAN. Ao desconectar os cabos, separe primeiro a extremidade do cabo que se encontra ligada � unidade.
�Advertencia!	En los puertos de redes de �rea extendida (WAN) existen tensiones de red peligrosas, tanto si la unidad est� conectada como si est� desconectada. Para evitar descargas el�ctricas, proceda con precauci�n cuando trabaje cerca de los puertos WAN. Para desconectar los cables, desconecte primero el extremo que va a la unidad.
Varning!	Farlig n�tverkssp�nning f�religger i WAN-portarna oavsett om str�mf�rs�rjningen till enheten �r bruten eller ej. F�r att undvika elektriska st�tar ska du vara f�rsiktig vid arbete i n�rheten av dessa portar. N�r du kopplar bort en kabel ska du f�rst koppla bort den �nde som inte �r ansluten till enheten.

Statement 29—Class I and Class 1M Laser Warning


Warning	Class I (21 CFR 1040.10 and 1040.11) and Class 1M (IEC 60825-1 2001-01) laser products.
Waarschuwing	Laserproducten van Klasse I (21 CFR 1040.10 en 1040.11) en Klasse 1M (IEC 60825-1 2001-01).
Varoitus	Luokan I (21 CFR 1040.10 ja 1040.11) ja luokan 1M (IEC 60825-1 2001-01) lasertuotteita.
Attention	Produits laser cat�gorie I (21 CFR 1040.10 et 1040.11) et cat�gorie 1M (IEC 60825-1 2001-01).
Warnung	Laserprodukte der Klasse I (21 CFR 1040.10 und 1040.11) und Klasse 1M (IEC 60825-1 2001-01).
Avvertenza	Prodotti laser di Classe I (21 CFR 1040.10 e 1040.11) e Classe 1M (IEC 60825-1 2001-01).
Advarsel	Klasse I (21 CFR 1040.10 og 1040.11) og klasse 1M (IEC 60825-1 2001-01) laserprodukter.
Aviso	Produtos laser Classe I (21 CFR 1040.10 e 1040.11) e Classe 1M (IEC 60825-1 2001-01).
�Advertencia!	Productos l�ser de Clase I (21 CFR 1040.10 y 1040.11) y Clase 1M (IEC 60825-1 2001-01).
Varning!	Laserprodukter av Klass I (21 CFR 1040.10 och 1040.11) och Klass 1M (IEC 60825-1 2001-01).

Statement 33—Battery Handling Warning


Warning	There is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions.
Waarschuwing	Er is ontploffingsgevaar als de batterij verkeerd vervangen wordt. Vervang de batterij slechts met hetzelfde of een equivalent type dat door de fabrikant aanbevolen is. Gebruikte batterijen dienen overeenkomstig fabrieksvoorschriften weggeworpen te worden.
Varoitus	R�j�hdyksen vaara, jos akku on vaihdettu v��r��n akkuun. K�yt� vaihtamiseen ainoastaan saman- tai vastaavantyyppist� akkua, joka on valmistajan suosittelema. H�vit� k�ytetyt akut valmistajan ohjeiden mukaan.
Attention	Danger d'explosion si la pile n'est pas remplac�e correctement. Ne la remplacer que par une pile de type semblable ou �quivalent, recommand�e par le fabricant. Jeter les piles usag�es conform�ment aux instructions du fabricant.
Warnung	Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie die Batterie nur durch den gleichen oder vom Hersteller empfohlenen Batterietyp. Entsorgen Sie die benutzten Batterien nach den Anweisungen des Herstellers.
Avvertenza	Pericolo di esplosione se la batteria non � installata correttamente. Sostituire solo con una di tipo uguale o equivalente, consigliata dal produttore. Eliminare le batterie usate secondo le istruzioni del produttore.
Advarsel	Det kan v�re fare for eksplosjon hvis batteriet skiftes p� feil m�te. Skift kun med samme eller tilsvarende type som er anbefalt av produsenten. Kasser brukte batterier i henhold til produsentens instruksjoner.
Aviso	Existe perigo de explos�o se a bateria for substitu�da incorrectamente. Substitua a bateria por uma bateria igual ou de um tipo equivalente recomendado pelo fabricante. Destrua as baterias usadas conforme as instru��es do fabricante.
�Advertencia!	Existe peligro de explosi�n si la bater�a se reemplaza de manera incorrecta. Reemplazar la bater�a exclusivamente con el mismo tipo o el equivalente recomendado por el fabricante. Desechar las bater�as gastadas seg�n las instrucciones del fabricante.
Varning!	Explosionsfara vid felaktigt batteribyte. Ers�tt endast batteriet med samma batterityp som rekommenderas av tillverkaren eller motsvarande. F�lj tillverkarens anvisningar vid kassering av anv�nda batterier.

Statement 258—Fan Tray Removal Warning


Warning	When removing the fan tray, keep your hands and fingers away from the spinning fan blades. Let the fan blades completely stop before you remove the fan tray.
Waarschuwing	Houd tijdens het verwijderen van de ventilator de handen en vingers uit de buurt van de draaiende ventilatorschoepen. Laat de ventilatorschoepen volledig tot stilstand komen alvorens de ventilator te verwijderen.
Varoitus	Pid� k�det ja sormet pois tuulettimen py�rivist� siivist� tuuletinalustaa poistaessasi. Anna tuulettimen siipien pys�hty� kokonaan ennen kuin irrotat tuuletinalustan.
Attention	Lors du retrait du plateau du ventilateur, veillez � ce que vos mains et doigts restent � l'�cart des pales en rotation du ventilateur. Attendez que les pales du ventilateur soient parvenues � une immobilit� compl�te avant de retirer le plateau du ventilateur.
Warnung	Beim Herausnehmen des L�fterkastens H�nde und Finger von den sich drehenden Gebl�sefl�geln fern halten. Vor Herausnehmen des Gebl�sekastens warten, bis die Gebl�sefl�gel v�llig zum Stillstand gekommen sind.
Figyelem!	Ha elt�vol�tja a ventil�tor bor�t�j�t, �gyeljen r�, hogy ne tegye kez�t vagy ujjait a ventil�tor forg� lap�tjai k�zel�be. A ventil�tor bor�t�j�nak elt�vol�t�sa el�tt v�rja meg, hogy a ventil�tor lap�tjai teljesen meg�lljanak.
Avvertenza	Quando si toglie il vano della ventola, fare attenzione che le mani e le dita non vengano in contatto con la ventola in movimento. Attendere che la ventola si fermi completamente prima di togliere il vano.
Advarsel	N�r du fjerner viftedekselet, hold hender og fingre borte fra de roterende viftebladene. La viftebladene stanse helt f�r du fjerner viftedekselet.
Aviso	Mantenha as suas m�os e dedos afastados das l�minas em movimento da ventoinha, ao retirar a respectiva bandeja. Deixe as l�minas da ventoinha parar completamente antes de retirar a bandeja.
�Advertencia!	Cuando quite la bandeja del abanico, mantenga las manos y los dedos alejados de las aspas en movimiento. Deje que las aspas se detengan completamente antes de quitar la bandeja del abanico.
Varning!	H�ll h�nder och fingrar borta fr�n de roterande fl�ktbladen n�r du tar av fl�ktskyddet. L�t fl�kten stanna helt innan du tar av fl�ktskyddet.

Regulatory Compliance

This section includes all regulatory, safety, EMC (Class A or Class B), telecom, and NEBS standards. The Cisco SCE platform is in compliance with national and international standards as described in Table 3.

Table 3 Regulatory Standards Compliance
Specification	Description
Regulatory Compliance	Products with the CE[1] Marking indicate compliance with the 93/68/EEC directive, which includes the safety and EMC standards listed.
Safety	•UL 1950, •CAN/CSA[2]-C22.2 No. 60950-00 •EN[3] 60950 •IEC[4] 60950 •IEC 60825-1 •EN 60825-1 •UL60950 •73/23/EEC •IEC825-1 •IEC825-2 •EN60825-1 •EN60825-2 •21CFR1040 •NOM-019-SCFI-1998 •Class I laser product
EMC[5]	•FCC[6] Part 15 (CFR 47) Class A •ICES[7]-003 •EN55022 •CISPR22 •EN 55024 •EN50082-1 •EN61000-3-2 •EN61000-3-3 •VCCI Class A •89/336/EEC
[1] CE—Committee European [2] CSA—Canadian Standards Association [3] EN—European Norm [4] IEC—International Electrotechnical Commission [5] EMC—Electromagnetic Compatibility [6] FCC—Federal Communications Commission [7] ICES—Interference-Causing Equipment Standard

The Cisco SCE platform conforms to the following list of industry EMC, safety, and environmental standards.

EMC Environmental Conditions for Products Installed in the European Union

This section applies to products to be installed in the European Union. The equipment is intended to operate under the following environmental conditions with respect to EMC:

Table 4 Industry EMC, Safety, and Environmental Standards
Specification	Description
ETS—European Telecommunications Standards	•ETS 300 019-1-2, Class 2.3 Transportation •ETS 300 019-1-3, Class 3.2 Stationary Use •ETS 300 019-2-1, Class 1.2 Storage •ETS 300 019-2-2, Class 2.3 Public Transportation •ETS 300 019-2-3, Class 3.2 In Use Weather Protected
NEBS—Network Equipment Building Systems	•Fully complies with Level 3 requirements: –GR63-Core, issue 3 –GR1089-Core, issue 4

•

Earthing and bonding shall meet the requirements of ETS 300 253 or CCITT K27.

•

AC power distribution shall be one of the following types, where applicable: TN-S and TN-C as defined in IEC 364-3.

In addition, if equipment is operated in a domestic environment, interference may occur.

FCC Declaration of Conformity Information

This equipment complies with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy. If it is not installed and used in accordance with the instruction manual, it may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to take whatever measures may be necessary to correct the interference at their own expense.

This equipment complies with the UL1950, the system must be connected to secondary circuits that are electrically isolated from accesses and connected to earth.

EMC Class A Compliance

For Class A compliance to the tested standards, the system is required to be cabled with Shielded Twisted Pair (STP) or Foiled Twisted Pair (FTP) cabling.

Canada ICES Class A Statement

Cet appareil num�rique de la classe A est conforme � la norme NMB-003 du Canada.

Statement 340—Class A Warning for CISPR22


Warning	This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
Waarschuwing	Dit is een product van klasse A. In een woonomgeving kan dit product radiostoring veroorzaken. In dat geval moet de gebruiker de juiste maatregelen nemen.
Varoitus	T�m� on A-luokan tuote. Kotona k�ytettyn� t�m� tuote voi aiheuttaa radiotaajuush�iri�it�, jolloin k�ytt�j�n tulisi ryhty� vaadittaviin toimenpiteisiin h�iri�iden ehk�isemiseksi.
Attention	Il s'agit d'un produit de classe A. Dans un environnement local, ce produit peut entra�ner des perturbations radio�lectriques, auquel cas l'utilisateur devra �ventuellement prendre des mesures ad�quates.
Warnung	Dies ist ein Produkt der Klasse A. Bei der Verwendung dieses Produkts im Haus- oder Wohnungsbereich kann es zu Funkst�rungen kommen. In diesem Fall muss der Benutzer u. U. angemessene Ma�nahmen ergreifen.
Avvertenza	Prodotto di classe A. � possibile che il prodotto generi interferenze radio in un ambienti chiusi. In questo caso l'utente deve intraprendere le misure adeguate per risolvere il problema.
Advarsel	Dette er et produkt i klasse A. I et hjemmemilj� kan dette produktet for�rsake radioforstyrrelser, og brukeren kan da v�re n�dt til � ta de n�dvendige forholdsregler.
Aviso	Este � um produto de classe A. Em um ambiente dom�stico, este produto pode causar interfer�ncia de r�dio. Nesse caso, talvez o usu�rio precise tomar as medidas adequadas.
�Advertencia!	Este es un producto de clase A. En el �mbito dom�stico, este producto puede causar radiointerferencias, lo que puede hacer necesaria la puesta en marcha de medidas adecuadas.
Varning!	Detta �r en klass A-produkt. Denna produkt kan orsaka radiost�rningar inomhus. Det kan d� vara ett krav att anv�ndaren vidtar l�mpliga �tg�rder.

Statement 191—VCCI Class A Warning for Japan

Statement 257—Class A Notice for Taiwan and Other Traditional Chinese Markets

Statement 294—Class A Warning for Korea

Statement 256—Class A Warning for Hungary

Statement 371-Power Cable and AC Adapter - Japan

Class A Notice for FCC

Modifying the equipment without Cisco's authorization may result in the equipment no longer complying with FCC requirements for Class A digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television communications at your own expense.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case users will be required to correct the interference at their own expense.

CSA NRTL (Canada)

This equipment is designed to meet the CSA requirements of UL1950, Safety of Information Technology Equipment. CSA is listed by the American Federal OSHA as equivalent to UL and other American safety testing laboratories under the NRTL program.

ULC (Canada)

The Industry Canada (formerly known as the Department of Communications) label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements. Industry Canada does not guarantee that equipment will operate to the user's satisfaction.

Warning	This is a Class A product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be required to take corrective actions.

Warning	This is a Class A Information Product, when used in residential environment, it may cause radio frequency interference, under such circumstances, the user may be requested to take appropriate countermeasures.

Warning	This is a Class A Device and is registered for EMC requirements for industrial use. The seller or buyer should be aware of this. If this type was sold or purchased by mistake, it should be replaced with a residential-use type.

Warning	This equipment is a class A product and should be used and installed properly according to the Hungarian EMC Class A requirements (MSZEN55022). Class A equipment is designed for typical commercial establishments for which special conditions of installation and protection distance are used.

Site Preparation and Safety Information

Preparing Your Site for Installation

To ensure normal system operation, plan your site configuration and prepare your site before installation.

Choosing a Site for Installation

•

Install the system in a restricted access area, where access can be gained only by service personnel through the use of a special tool, lock and key, or other means of security.

•

Choose a site that maintains an ambient temperature of 23� to 131�F (-5� to 55�C).

Ensuring Overcurrent Protection

The system relies on the protective devices in the building installation for protection against short-circuit, overcurrent, and earth (grounding) fault. Ensure that the protective devices in the building installation are properly rated to protect the system, and that they comply with national and local codes.

Grounding the System

Creating a Safe Environment

•

Clear the area of possible hazards, such as moist floors, ungrounded power extension cables, and missing safety grounds.

•

Keep the area around the chassis free from dust and foreign conductive material (such as metal flakes from nearby construction activity.)

Rack-Mounting the System

A rack-mount kit comes with the system. The kit is not suitable for racks with obstructions (such as a power strip) that could impair access to system components. Allow sufficient clearance around the rack for system maintenance.

Ensuring Proper Airflow

•

Install the system in an open rack whenever possible. If installation in an enclosed rack is unavoidable, ensure that the rack has adequate ventilation.

•

Maintain ambient airflow to ensure normal operation. If the airflow is blocked or restricted, or if the intake air is too warm, an overtemperature condition can occur.

•

Allow at least 2 inches (5 cm) of clearance at each side and at least 5 inches (12.7 cm) of clearance at the rear of the platform.

•

Avoid placing the system in an overly congested rack or directly next to another equipment rack. Heat exhaust from other equipment can enter the inlet air vents and cause an overtemperature condition.

•

Ensure that cables from other equipment do not obstruct the airflow through the chassis or impair access to the power supplies.

Stabilizing the System

•

Install any stabilizers that came with your equipment rack before mounting or servicing the system in the rack.

•

Load the rack from the bottom to the top, with the heaviest system at the bottom.

•

Do not stack the system on top of any other equipment. If the system falls, it can cause severe bodily injury and damage the equipment.

•

If you are using an equipment shelf, ensure that the shelf is constructed to support the weight and dimensions of the chassis.

•

If you are using a two-post rack, ensure that the weight of the chassis does not make the rack unstable. Secure the two-post rack with ceiling brackets if the rack is populated with heavy equipment.

Lifting the System

•

Depending on the weight of the system, more than one person might be required to lift it.

•

Ensure that your footing is solid and the weight of the system is evenly distributed between your feet.

•

Lift the system slowly, keeping your back straight. Lift with your legs, not with your back. Bend at the knees, not at the waist.

•

Do not attempt to lift the system with the handles on the power supplies. These handles are not designed to support the weight of the system.

Power Considerations

Both AC and DC power supplies are available. Under normal operating conditions, the system is intended to operate with either two AC power supplies or two DC power supplies.

Note Refer to your hardware installation guide for AC and DC power specifications.

AC Power

•

The system is designed for connection to TN power systems. A TN power system is a power distribution system with one point connected directly to earth (ground). The exposed conductive parts of the installation are connected to that point by protective earth conductors.

•

Ensure that the plug-socket combination is accessible at all times, because it serves as the main disconnecting device.

DC Power

•

Connect DC-input power supplies only to a DC power source that complies with the safety extra-low voltage (SELV) requirements in the UL1950, UL60950, CSA60950, CSA950, EN60950, and IEC60950 standards.

•

Incorporate a readily accessible two-poled disconnect device in the fixed wiring.

•

Ensure that power is removed from the DC circuit before installing or removing power supplies. Tape the switch handle of the DC circuit breaker in the off position.

•

Use approved wiring terminations; hex or loop connectors. These terminations should be the appropriate size for the wires and should clamp both the insulation and the conductor.

•

Ensure that no exposed portion of the DC-input power source wire extends from the terminal block plug. An exposed wire can conduct a harmful level of electricity.

Redundant Power

Connect each of the two power supplies to different input power sources. Failure to do so makes the system susceptible to total power failure in the event that one of the power supplies fails.

Preventing ESD

Electrostatic discharge (ESD) damage occurs when electronic cards or components are mishandled and can result in complete or intermittent failures. Note the following guidelines before you install or service the system:

•

Always wear an ESD-preventive wrist or ankle strap when handling electronic components. Connect one end of the strap to an ESD jack or an unpainted metal component on the system (such as a captive installation screw).

•

Handle cards by the faceplates and edges only; avoid touching the printed circuit board and connector pins.

•

Place any removed component on an antistatic surface or in a static shielding bag.

•

Avoid contact between the cards and clothing. The wrist strap only protects the card from ESD voltages on the body; ESD voltages on clothing can still cause damage.

Note For safety, periodically check the resistance value of the antistatic strap. The measurement should be between 1 and 10 megohms (Mohms).

Installing and Servicing the System

•

Install the system in compliance with your local and national electrical codes:

–

United States: National Fire Protection Association (NFPA) 70; United States National Electrical Code.

–

Other countries: If local and national electrical codes are not available, refer to IEC 364, Part 1 through Part 7.

•

Do not perform any action that creates a potential hazard to people or makes the equipment unsafe.

•

Remove all jewelry (including rings and chains) or other items that could get caught in the system or heat up and cause serious burns

Disconnecting Power

•

Locate the emergency power-off switch for the room before working with the system.

•

Turn off the power and disconnect the power from the circuit when working with components that are not hot-swappable. If the system does not have an on/off switch, unplug the power cord.

•

To completely de-energize the system, disconnect the power connection to all power supplies.

•

For DC power supplies, locate the circuit breaker on the panel board that services the DC circuit, switch the circuit breaker to the off position, and tape the switch handle of the circuit breaker in the off position.

•

Do not touch the power supply when the power cord is connected. Line voltages are present within the power supply even when the power switch is off and the power cord is connected.

Preventing EMI

When you run wires for any significant distance in an electromagnetic field, electromagnetic interference (EMI) can occur between the field and the signals on the wires.

Note Strong EMI, especially when it is caused by lightning or radio transmitters, can destroy the signal drivers and receivers in the system, and can even create an electrical hazard by conducting power surges through lines and into the system.

Disposing of the System

Dispose of the system and its components (including batteries) as specified by all national laws and regulations.

Related Publications

Your SCE Platform and the software running on it contain extensive features and functionality, which are documented in the following resources:

Note

You can access Cisco software configuration and hardware installation and maintenance documentation on the World Wide Web at Cisco Website URL http://www.cisco.com. Translated documentation is available at the following URL: International Cisco Website http://www.cisco.com/public/countries_languages.shtml

•

For initial installation and startup information, refer to the relevant Cisco SCE Platform Quick Start Guide.

•

For complete installation and initial configuration instructions, refer to the relevant Cisco SCE Platform Installation and Configuration Guide.

•

For installation and configuration of the other components of the Service Control Management Suite refer to:

•

To view Cisco documentation or obtain general information about the documentation, refer to the following sources:

Cisco Service Control Engine 2000 GBE-FE RCS Differences

Table 5 lists the differences between the Cisco SCE 2000 FE and the SCE 2000 GBE.

Obtaining Documentation

Cisco documentation and additional literature are available on Cisco.com. Cisco also provides several ways to obtain technical assistance and other technical resources. These sections explain how to obtain technical information from Cisco Systems.

Cisco.com

Documentation Feedback

You can submit comments by using the response card (if present) behind the front cover of your document or by writing to the following address:

Table 5 RCS Differences Between the Cisco Service Engines, SCE2000 GBE and SCE2000 FE
RCS Topic	SCE2000 GBE	SCE2000 FE
Warning Definition Statement	Class 1/I laser product warning	No laser warning
Regulatory Standards Compliance Regulatory Compliance table In Safety row—	Class I laser product	No laser
Working with Lasers	Topic present	Topic not present

Cisco Systems
Attn: Customer Document Ordering
170 West Tasman Drive
San Jose, CA 95134-9883

Obtaining Technical Assistance

For all customers, partners, resellers, and distributors who hold valid Cisco service contracts, Cisco Technical Support provides 24-hour-a-day, award-winning technical assistance. The Cisco Technical Support Website on Cisco.com features extensive online support resources. In addition, Cisco Technical Assistance Center (TAC) engineers provide telephone support. If you do not hold a valid Cisco service contract, contact your reseller.

Cisco Technical Support Website

The Cisco Technical Support Website provides online documents and tools for troubleshooting and resolving technical issues with Cisco products and technologies. The website is available 24 hours a day, 365 days a year, at this URL:

Access to all tools on the Cisco Technical Support Website requires a Cisco.com user ID and password. If you have a valid service contract but do not have a user ID or password, you can register at this URL:

Note Use the Cisco Product Identification (CPI) tool to locate your product serial number before submitting a web or phone request for service. You can access the CPI tool from the Cisco Technical Support Website by clicking the Tools & Resources link under Documentation & Tools. Choose Cisco Product Identification Tool from the Alphabetical Index drop-down list, or click the Cisco Product Identification Tool link under Alerts & RMAs. The CPI tool offers three search options: by product ID or model name; by tree view; or for certain products, by copying and pasting show command output. Search results show an illustration of your product with the serial number label location highlighted. Locate the serial number label on your product and record the information before placing a service call.

Submitting a Service Request

Using the online TAC Service Request Tool is the fastest way to open S3 and S4 service requests. (S3 and S4 service requests are those in which your network is minimally impaired or for which you require product information.) After you describe your situation, the TAC Service Request Tool provides recommended solutions. If your issue is not resolved using the recommended resources, your service request is assigned to a Cisco TAC engineer. The TAC Service Request Tool is located at this URL:

For S1 or S2 service requests or if you do not have Internet access, contact the Cisco TAC by telephone. (S1 or S2 service requests are those in which your production network is down or severely degraded.) Cisco TAC engineers are assigned immediately to S1 and S2 service requests to help keep your business operations running smoothly.

Asia-Pacific: +61 2 8446 7411 (Australia: 1 800 805 227)
EMEA: +32 2 704 55 55
USA: 1 800 553-2447

Definitions of Service Request Severity

To ensure that all service requests are reported in a standard format, Cisco has established severity definitions.

Severity 1 (S1)—Your network is "down," or there is a critical impact to your business operations. You and Cisco will commit all necessary resources around the clock to resolve the situation.

Severity 2 (S2)—Operation of an existing network is severely degraded, or significant aspects of your business operation are negatively affected by inadequate performance of Cisco products. You and Cisco will commit full-time resources during normal business hours to resolve the situation.

Severity 3 (S3)—Operational performance of your network is impaired, but most business operations remain functional. You and Cisco will commit resources during normal business hours to restore service to satisfactory levels.

Severity 4 (S4)—You require information or assistance with Cisco product capabilities, installation, or configuration. There is little or no effect on your business operations.

Obtaining Additional Publications and Information

Information about Cisco products, technologies, and network solutions is available from various online and printed sources.

•

Cisco Marketplace provides a variety of Cisco books, reference guides, and logo merchandise. Visit Cisco Marketplace, the company store, at this URL:

•

The Cisco Product Catalog describes the networking products offered by Cisco Systems, as well as ordering and customer support services. Access the Cisco Product Catalog at this URL:

•

Cisco Press publishes a wide range of general networking, training and certification titles. Both new and experienced users will benefit from these publications. For current Cisco Press titles and other information, go to Cisco Press at this URL:

•

Packet magazine is the Cisco Systems technical user magazine for maximizing Internet and networking investments. Each quarter, Packet delivers coverage of the latest industry trends, technology breakthroughs, and Cisco products and solutions, as well as network deployment and troubleshooting tips, configuration examples, customer case studies, certification and training information, and links to scores of in-depth online resources. You can access Packet magazine at this URL:

•

iQ Magazine is the quarterly publication from Cisco Systems designed to help growing companies learn how they can use technology to increase revenue, streamline their business, and expand services. The publication identifies the challenges facing these companies and the technologies to help solve them, using real-world case studies and business strategies to help readers make sound technology investment decisions. You can access iQ Magazine at this URL:

•

Internet Protocol Journal is a quarterly journal published by Cisco Systems for engineering professionals involved in designing, developing, and operating public and private internets and intranets. You can access the Internet Protocol Journal at this URL:

•

World-class networking training is available from Cisco. You can view current offerings at this URL:

Table Of Contents