|
This guide provides cable assemblies and pinouts for the cables that shipped with the Cisco AccessPath-VS3 Packet Telephony Concentrator.
The guide includes the following cable assembly and pinout information:
The Cisco AccessPath-VS3 system shelves connect to each other through the signal harness. Throughout this guide, cable connections to the signal harness are described using the signal harness connector numbers, J1 through J58. These connector numbers are stencilled on the signal harness. (See Figure 1.)
The patch panels route T1/E1 PRI connections into the Cisco AccessPath-VS3 system.
The patch panel-to-signal harness cable (72-1466-xx) delivers T1/E1 PRI signals from the patch panels to the Cisco AS5300 Access VoIP Shelves through connections to J1-J4 and J9-J12 on the signal harness. (See Figure 2 and Table 1.)
Cable Leg | 25 Pin | Signal | Description | 64 Pin | Twisted Pair |
---|---|---|---|---|---|
P1 | 1 | Rx Tip + | Receive Tip + | 1 | 1 |
2 | Tx Tip + | Transmit Tip + | 2 | 2 | |
3 | Rx Tip + | Receive Tip + | 3 | 3 | |
4 | Tx Tip + | Transmit Tip + | 4 | 4 | |
5 | Rx Tip + | Receive Tip + | 5 | 5 | |
6 | Tx Tip + | Transmit Tip + | 6 | 6 | |
7 | Rx Tip + | Receive Tip + | 7 | 7 | |
8 | Tx Tip + | Transmit Tip + | 8 | 8 | |
14 | Rx Ring - | Receive Ring - | 33 | 1 | |
15 | Tx Ring - | Transmit Ring - | 34 | 2 | |
16 | Rx Ring - | Receive Ring - | 35 | 3 | |
17 | Tx Ring - | Transmit Ring - | 36 | 4 | |
18 | Rx Ring - | Receive Ring - | 37 | 5 | |
19 | Tx Ring - | Transmit Ring - | 38 | 6 | |
20 | Rx Ring - | Receive Ring - | 39 | 7 | |
21 | Tx Ring - | Transmit Ring - | 40 | 8 | |
P2 | 1 | Rx Tip + | Receive Tip + | 9 | 1 |
2 | Tx Tip + | Transmit Tip + | 10 | 2 | |
3 | Rx Tip + | Receive Tip + | 11 | 3 | |
4 | Tx Tip + | Transmit Tip + | 12 | 4 | |
5 | Rx Tip + | Receive Tip + | 13 | 5 | |
6 | Tx Tip + | Transmit Tip + | 14 | 6 | |
7 | Rx Tip + | Receive Tip + | 15 | 7 | |
8 | Tx Tip + | Transmit Tip + | 16 | 8 | |
14 | Rx Ring - | Receive Ring - | 41 | 1 | |
15 | Tx Ring - | Transmit Ring - | 42 | 2 | |
16 | Rx Ring - | Receive Ring - | 43 | 3 | |
17 | Tx Ring - | Transmit Ring - | 44 | 4 | |
18 | Rx Ring - | Receive Ring - | 45 | 5 | |
19 | Tx Ring - | Transmit Ring - | 46 | 6 | |
20 | Rx Ring - | Receive Ring - | 47 | 7 | |
21 | Tx Ring - | Transmit Ring - | 48 | 8 | |
P3 | 1 | Rx Tip + | Receive Tip + | 17 | 1 |
2 | Tx Tip + | Transmit Tip + | 18 | 2 | |
3 | Rx Tip + | Receive Tip + | 19 | 3 | |
4 | Tx Tip + | Transmit Tip + | 20 | 4 | |
5 | Rx Tip + | Receive Tip + | 21 | 5 | |
6 | Tx Tip + | Transmit Tip + | 22 | 6 | |
7 | Rx Tip + | Receive Tip + | 23 | 7 | |
8 | Tx Tip + | Transmit Tip + | 24 | 8 | |
14 | Rx Ring - | Receive Ring - | 49 | 1 | |
15 | Tx Ring - | Transmit Ring - | 50 | 2 | |
16 | Rx Ring - | Receive Ring - | 51 | 3 | |
17 | Tx Ring - | Transmit Ring - | 52 | 4 | |
18 | Rx Ring - | Receive Ring - | 53 | 5 | |
19 | Tx Ring - | Transmit Ring - | 54 | 6 | |
20 | Rx Ring - | Receive Ring - | 55 | 7 | |
21 | Tx Ring - | Transmit Ring - | 56 | 8 | |
P4 | 1 | Rx Tip + | Receive Tip + | 25 | 1 |
2 | Tx Tip + | Transmit Tip + | 26 | 2 | |
3 | Rx Tip + | Receive Tip + | 27 | 3 | |
4 | Tx Tip + | Transmit Tip + | 28 | 4 | |
5 | Rx Tip + | Receive Tip + | 29 | 5 | |
6 | Tx Tip + | Transmit Tip + | 30 | 6 | |
7 | Rx Tip + | Receive Tip + | 31 | 7 | |
8 | Tx Tip + | Transmit Tip + | 32 | 8 | |
14 | Rx Ring - | Receive Ring - | 57 | 1 | |
15 | Tx Ring - | Transmit Ring - | 58 | 2 | |
16 | Rx Ring - | Receive Ring - | 59 | 3 | |
17 | Tx Ring - | Transmit Ring - | 60 | 4 | |
18 | Rx Ring - | Receive Ring - | 61 | 5 | |
19 | Tx Ring - | Transmit Ring - | 62 | 6 | |
20 | Rx Ring - | Receive Ring - | 63 | 7 | |
21 | Tx Ring - | Transmit Ring - | 64 | 8 |
Table 2 shows the channel mapping in the connection between Cisco AS5300 VoIP Access Shelves 1 through 7 and patch panel 1. Note that port numbers 2 and 3 are not available on the Cisco AS5300 with the Voice/Fax Feature Card.
Patch Panel 1 Circuit Number | Connects to Port Number | On Cisco AS5300 VoIP Access Shelf |
---|---|---|
1 | PRI 0 | FS01 |
2 | PRI 1 | |
3 | PRI 2 - | |
4 | PRI 3 - | |
5 | PRI 0 | FS02 |
6 | PRI 1 | |
7 | PRI 2 - | |
8 | PRI 3 - | |
9 | PRI 0 | FS03 |
10 | PRI 1 | |
11 | PRI 2 - | |
12 | PRI 3 - | |
13 | PRI 0 | FS04 |
14 | PRI 1 | |
15 | PRI 2 - | |
16 | PRI 3 - | |
17 | PRI 0 | FS05 |
18 | PRI 1 | |
19 | PRI 2 - | |
20 | PRI 3 - | |
21 | PRI 0 | FS06 |
22 | PRI 1 | |
23 | PRI 2 - | |
24 | PRI 3 - | |
25 | PRI 0 | FS07 |
26 | PRI 1 | |
27 | PRI 2 - | |
28 | PRI 3 - |
Table 3 shows the channel mapping in the connection between Access VoIP Shelves 8 through 14 and patch panel 2. Again, note that ports numbers 2 and 3 are not available on the Cisco AS5300 with the Voice/Fax Feature Card.
Patch Panel 2 Circuit Number | Connects to Port Number | On Cisco AS5300 VoIP Access Shelf |
---|---|---|
1 | PRI 0 | FS08
|
2 | PRI 1 | |
3 | PRI 2 - | |
4 | PRI 3 - | |
5 | PRI 0 | FS09 |
6 | PRI 1 | |
7 | PRI 2 - | |
8 | PRI 3 - | |
9 | PRI 0 | FS10 |
10 | PRI 1 | |
11 | PRI 2 - | |
12 | PRI 3 - | |
13 | PRI 0 | FS11 |
14 | PRI 1 | |
15 | PRI 2 - | |
16 | PRI 3 - | |
17 | PRI 0 | FS12 |
18 | PRI 1 | |
19 | PRI 2 - | |
20 | PRI 3 - | |
21 | PRI 0 | FS13 |
22 | PRI 1 | |
23 | PRI 2 - | |
24 | PRI 3 - | |
25 | PRI 0 | FS14 |
26 | PRI 1 | |
27 | PRI 2 - | |
28 | PRI 3 - |
Table 4 shows the channel mapping in the connection between Access VoIP Shelves 15 through 21 and patch panel 1 in the secondary cabinet for High-End Extended configurations only.
Patch Panel 1 Circuit Number | Connects to Port Number | On Cisco AS5300 Access VoIP Shelf |
1 | PRI 0 | FS15 |
2 | PRI 1 | |
3 | PRI 2 - | |
4 | PRI 3 - | |
5 | PRI 0 | FS16 |
6 | PRI 1 | |
7 | PRI 2 - | |
8 | PRI 3 - | |
9 | PRI 0 | FS17 |
10 | PRI 1 | |
11 | PRI 2 - | |
12 | PRI 3 - | |
13 | PRI 0 | FS18 |
14 | PRI 1 | |
15 | PRI 2 - | |
16 | PRI 3 - | |
17 | PRI 0 | FS19 |
18 | PRI 1 | |
19 | PRI 2 - | |
20 | PRI 3 - | |
21 | PRI 0 | FS20 |
22 | PRI 1 | |
23 | PRI 2 - | |
24 | PRI 3 - | |
25 | PRI 0 | FS21 |
26 | PRI 1 | |
27 | PRI 2 - | |
28 | PRI 3 - |
Each Cisco AS5300 Access VoIP Shelf comes from the factory with the following:
The Cisco AS5300 Access VoIP Shelf cable assemblies and pinouts include the following:
The Access VoIP Shelf's Console/Ethernet cable (Figure 3) connects from the Console port, the Fast Ethernet (10 BaseT/100 BaseT), and Ethernet (10 BaseT) ports on the Cisco AS5300 Access VoIP Shelves to the even numbered connectors, from J14 through J40, on the signal harness.
The Access VoIP Shelf Console/Ethernet Cable allows the Cisco 3640 System Controller to make a console connection to the Access VoIP Shelf for management and provides redundant data paths to the Cisco Catalyst 5002 Switch Shelf and the Cisco Ethernet switching port adapter on the Cisco 7206 Router Shelf. (See Figure 3 and Table 5.)
RJ-45 Plug | Shelf Connection | RJ-45 Pin | Twisted Pair | Signal | Description | 25-Pin |
---|---|---|---|---|---|---|
1 (Light blue) | Console | 1 | 4 | - | - | - |
2 | CON DSR | Console Data Set Ready | 8 | |||
3 | 3 | CON Rx | Console Receive | 6 | ||
4 | CON Rx_GND | Console Receive Ground | 19 | |||
5 | 2 | CON Tx_GND | Console Transmit Ground | 20 | ||
6 | CON Tx | Console Transmit | 7 | |||
7 | 1 | CON DTR | Console Data Terminal Ready | 21 | ||
8 | - | - | - | |||
2 (Yellow) | 10/100BaseT | 1 | 2 | ETH-1 Tx+ | Ethernet Transmit + | 1 |
2 | ETH-1 Tx- | Ethernet Transmit - | 14 | |||
3 | 1 | ETH-1 Rx+ | Ethernet Receive + | 3 | ||
6 | ETH-1 Rx- | Ethernet Receive - | 16 | |||
3 (Yellow) | 10BaseT | 1 | 2 | ETH-2 Tx+ | Ethernet Transmit + | 25 |
2 | ETH-2 Tx- | Ethernet Transmit - | 13 | |||
3 | 1 | ETH-2 Rx+ | Ethernet Receive + | 23 | ||
6 | ETH-2 Rx- | Ethernet Receive - | 11 |
The Access VoIP Shelf's T1/E1 PRI cable (Figure 3) connects from the T1/E1 PRI ports on the Cisco AS5300 Access VoIP Shelves to the odd numbered connectors, from J13 through J39, on the signal harness. This cable allows the Cisco AS5300 Access VoIP Shelves to receive calls from the patch panels. (See Figure 4 and Table 6.)
RJ-45 Plug | Shelf Connection | RJ-45 Pin | Twisted Pair | Signal | Description | 36 Pin |
---|---|---|---|---|---|---|
1 (Tan) | PRI 0 | 1 | 2 | T1-1 Rx- | T1/E1 PRI Receive - | 20 |
2 | T1-1 Rx+ | T1/E1 PRI Receive + | 2 | |||
4 | 1 | T1-1 Tx- | T1/E1 PRI Transmit - | 21 | ||
5 | T1-1 Tx+ | T1/E1 PRI Transmit + | 3 | |||
2 (Tan) | PRI 1 | 1 | 2 | T1-2 Rx- | T1/E1 PRI Receive - | 22 |
2 | T1-2 Rx+ | T1/E1 PRI Receive + | 4 | |||
4 | 1 | T1-2 Tx- | T1/E1 PRI Transmit - | 23 | ||
5 | T1-2 Tx+ | T1/E1 PRI Transmit + | 5 | |||
3 (Tan) | PRI 2 | 1 | 2 | T1-3 Rx- | T1/E1 PRI Receive - | 24 |
2 | T1-3 Rx+ | T1/E1 PRI Receive + | 6 | |||
4 | 1 | T1-3 Tx- | T1/E1 PRI Transmit - | 25 | ||
5 | T1-3 Tx+ | T1/E1 PRI Transmit + | 7 | |||
4 (Tan) | PRI 3 | 1 | 2 | T1-4 Rx- | T1/E1 PRI Receive - | 26 |
2 | T1-4 Rx+ | T1/E1 PRI Receive + | 8 | |||
4 | 1 | T1-4 Tx- | T1/E1 PRI Transmit - | 27 | ||
5 | T1-4 Tx+ | T1/E1 PRI Transmit + | 9 |
The following sections describe cable assemblies and pinouts for the Cisco 7206 Router Shelf.
Each of the Cisco 7206 Router Shelves in a dual Router Shelf configuration uses a Model BL-6000 MII-to-MII Crossover IEEE 802.3u Adapter to connect from its Fast Ethernet MII port in slot 0 to the corresponding port on the other Router Shelf.
The female MII connector on the Cisco 7206 Router Shelves is in an idle state, compliant to IEEE 802.3u, until cables are attached.
The Router Shelf software configuration must contain the following lines:
interface FastEthernet0/0
!
full-duplex
no keepalive
The inclusion of these lines stops the Router Shelf from sending out packets which it expects to see returned. Otherwise it will shut down the line.
These transceivers should have been installed before the Cisco AccessPath-VS3 system was shipped.
The adapters have 4 diagnostic lights. For information on the diagnostic lights, see Table 7.
Light | Function |
---|---|
Link/Activity (Green) | Indicates that the adapter is connected to the Router Shelf, that the circuit between the 2 Cisco 7206 Router Shelves is complete, and that data is being received. |
Power (Green) | This light will be on continuously while power is being supplied to the transceiver from the MII receptacle on the Router Shelf. |
The adapters use the pinouts required by the Router Shelf MII receptacle. For information on these pinouts, refer to the Cisco 7206 Installation and Configuration Guide.
The Cisco 7206 Router Shelf's Ethernet switching cables (Figure 5) connect from the Ethernet ports on the Cisco Ethernet switching port adapter as follows:
For all configurations72-1462-xx connects from the Cisco Ethernet switching port adapter to J46 (for Cisco 7206 Router Shelf 1) or J42 (for Cisco 7206 Router Shelf 2) on the signal harness. This cable allows the Cisco 7206 Router Shelves to provide failover switching if the Cisco Catalyst 5002 Switch Shelf stops functioning. (See Figure 5 and Table 8.)
RJ-45 Plug | Shelf Connection | RJ-45 Pin | Twisted Pair | Signal | Description | 50 Pin |
---|---|---|---|---|---|---|
1 (Yellow) | Port 1 | 1 | 2 | Tx+ | Transmit + | 1 |
|
| 2 | 2 | Tx- | Transmit - | 26 |
|
| 3 | 1 | Rx+ | Receive + | 2 |
|
| 6 | 1 | Rx- | Receive - | 27 |
2 (Yellow) | Port 2 | 1 | 2 | Tx+ | Transmit + | 3 |
|
| 2 | 2 | Tx- | Transmit - | 28 |
|
| 3 | 1 | Rx+ | Receive + | 4 |
|
| 6 | 1 | Rx- | Receive - | 29 |
3 (Yellow) | Port 3 | 1 | 2 | Tx+ | Transmit + | 5 |
|
| 2 | 2 | Tx- | Transmit - | 30 |
|
| 3 | 1 | Rx+ | Receive + | 6 |
|
| 6 | 1 | Rx- | Receive - | 31 |
4 (Yellow) | Port 4 | 1 | 2 | Tx+ | Transmit + | 7 |
|
| 2 | 2 | Tx- | Transmit - | 32 |
|
| 3 | 1 | Rx+ | Receive + | 8 |
|
| 6 | 1 | Rx- | Receive - | 33 |
5 (Yellow) | Port 5 | 1 | 2 | Tx+ | Transmit + | 9 |
|
| 2 | 2 | Tx- | Transmit - | 34 |
|
| 3 | 1 | Rx+ | Receive + | 10 |
|
| 6 | 1 | Rx- | Receive - | 35 |
6 (Yellow) | Port 6 | 1 | 2 | Tx+ | Transmit + | 11 |
|
| 2 | 2 | Tx- | Transmit - | 36 |
|
| 3 | 1 | Rx+ | Receive + | 12 |
|
| 6 | 1 | Rx- | Receive - | 37 |
7 (Yellow) | Port 7 | 1 | 2 | Tx+ | Transmit + | 13 |
|
| 2 | 2 | Tx- | Transmit - | 38 |
|
| 3 | 1 | Rx+ | Receive + | 14 |
|
| 6 | 1 | Rx- | Receive - | 39 |
8 (Yellow) | Port 8 | 1 | 2 | Tx+ | Transmit + | 15 |
|
| 2 | 2 | Tx- | Transmit - | 40 |
|
| 3 | 1 | Rx+ | Receive + | 16 |
|
| 6 | 1 | Rx- | Receive - | 41 |
9 (Yellow) | Port 9 | 1 | 2 | Tx+ | Transmit + | 17 |
|
| 2 | 2 | Tx- | Transmit - | 42 |
|
| 3 | 1 | Rx+ | Receive + | 18 |
|
| 6 | 1 | Rx- | Receive - | 43 |
10 (Yellow) | Port 10 | 1 | 2 | Tx+ | Transmit + | 19 |
|
| 2 | 2 | Tx- | Transmit - | 44 |
|
| 3 | 1 | Rx+ | Receive + | 20 |
|
| 6 | 1 | Rx- | Receive - | 45 |
11 (Yellow) | Port 11 | 1 | 2 | Tx+ | Transmit + | 21 |
|
| 2 | 2 | Tx- | Transmit - | 46 |
|
| 3 | 1 | Rx+ | Receive + | 22 |
|
| 6 | 1 | Rx- | Receive - | 47 |
12 (Yellow) | Port 12 | 1 | 2 | Tx+ | Transmit + | 23 |
|
| 2 | 2 | Tx- | Transmit - | 48 |
|
| 3 | 1 | Rx+ | Receive + | 24 |
|
| 6 | 1 | Rx- | Receive - | 49 |
The Cisco 7206 Router Shelf's Console/Ethernet cables (Figure 5) connect from console and Ethernet ports on the Cisco 7206 Router Shelf to J41 (for Cisco 7206 Router Shelf 2) and J44 (for Cisco 7206 Router Shelf 1).
This cable connects the Cisco 7206 Router Shelves to the Cisco 3640 System Controller for console management. (See Figure 6 and Table 9.)
RJ-45 Plug | Shelf Connection | RJ-45Pin | Twisted Pair | Signal | Description | 15 Pin |
---|---|---|---|---|---|---|
1 (Light blue) | Console | 1 | 4 | - | - | - |
2 | CON DSR | Console Data Set Ready | 15 | |||
3 | 3 | CON Rx | Console Receive | 13 | ||
4 | CON Rx_GND | Console Receive Ground | 6 | |||
5 | 2 | CON Tx_GND | Console Transmit Ground | 7 | ||
6 | CON Tx | Console Transmit | 14 | |||
7 | 1 | CON DTR | Console Data Terminal Ready | 8 | ||
8 | - | - | - | |||
2 (Yellow) | Ethernet | 1 | 2 | ETH Tx+ | Transmit + | 1 |
2 | ETH Tx- | Transmit - | 9 | |||
3 | 1 | ETH Rx+ | Receive + | 3 | ||
6 | ETH Rx- | Receive - | 11 |
The Cisco 7206 Router Shelf's controller and interconnect cables (Figure 7 and Figure 8) connect the Cisco 7206 Router Shelves in to the other Cisco 7206 Router Shelf in dual Cisco 7206 Router Shelf configurations:
These cables look the same but do not have the same pinouts.
Shelf Connection | RJ-45 Pin | RJ-45 Pin |
---|---|---|
RS 5/0 to RS 0/0 | 1 | 1 |
2 | 2 | |
3 | 3 | |
4 | 4 | |
5 | 5 | |
6 | 6 | |
7 | 7 | |
8 | 8 |
Shelf Connection | RJ-45 Pin | RJ-45 Pin |
---|---|---|
RS 5/1 on Cisco 7206 Router Shelf 1 to RS 5/1 on Cisco 7206 Router Shelf 2 | 1 | 3 |
2 | 6 | |
3 | 1 | |
4 | 4 | |
5 | 5 | |
6 | 2 | |
7 | 7 | |
8 | 8 |
The Cisco 3640 System Controller connects to the signal harness using 2 cable types. These cables are described in the following sections:
The Cisco 3640 System Controller's Fast Ethernet cable connects from the Fast Ethernet ports on the Cisco 3640 System Controller to J48 on the signal harness. (See Figure 9 and Table 12.)
RJ-45 Plug | Shelf Connection | RJ-45 Pin | Twisted Pair | Signal | Description | 9 Pin |
---|---|---|---|---|---|---|
1 (Yellow) | Fast Ethernet 1 | 1 | 2 | ETH-1 Tx+ | Transmit + | 1 |
2 | ETH-1 Tx- | Transmit - | 6 | |||
3 | 1 | ETH-1 Rx+ | Receive + | 2 | ||
6 | ETH-1 Rx- | Receive - | 7 | |||
2 (Yellow) | Fast Ethernet 0 | 1 | 2 | ETH-2 Tx+ | Transmit + | 5 |
2 | ETH-2 Tx- | Transmit - | 9 | |||
3 | 1 | ETH-2 Rx+ | Receive + | 4 | ||
6 | ETH-2 Rx- | Receive - | 8 |
The Cisco 3640 System Controller's asynchronous cable connects from the asynchronous ports on the Cisco 3640 System Controller to ports J49 through J52 on the signal harness.
Connector Number | 68 Pin SCSI | Signal | Description | Connector Number | 68 Pin SCSI | Twisted Pair |
---|---|---|---|---|---|---|
1 | 1 | - | - | 2 | 1 | 1 |
| 2 | RTS | Request To Send |
| 2 | 2 |
| 3 | TxD | Transmit Data |
| 3 | 3 |
| 4 | Rx-GND | Receive Ground |
| 4 | 4 |
| 5 | DSR | Data Set Ready |
| 5 | 5 |
| 6 | RTS | Request To Send |
| 6 | 6 |
| 7 | TxD | Transmit Data |
| 7 | 7 |
| 8 | Rx-GND | Receive Ground |
| 8 | 8 |
| 9 | DSR | Data Set Ready |
| 9 | 9 |
| 10 | RTS | Request To Send |
| 10 | 10 |
| 11 | TxD | Transmit Data |
| 11 | 11 |
| 12 | Rx-GND | Receive Ground |
| 12 | 12 |
| 13 | DSR | Data Set Ready |
| 13 | 13 |
| 14 | RTS | Request To Send |
| 14 | 14 |
| 15 | TxD | Transmit Data |
| 15 | 15 |
| 16 | Rx-GND | Receive Ground |
| 16 | 16 |
| 17 | DSR | Data Set Ready |
| 17 | 17 |
| 18 | RTS | Request To Send |
| 18 | 18 |
| 19 | TxD | Transmit Data |
| 19 | 19 |
| 20 | Rx-GND | Receive Ground |
| 20 | 20 |
| 21 | DSR | Data Set Ready |
| 21 | 21 |
| 22 | RTS | Request To Send |
| 22 | 22 |
1 | 23 | TxD | Transmit Data | 2 | 23 | 23 |
| 24 | Rx-GND | Receive Ground |
| 24 | 24 |
| 25 | DSR | Data Set Ready |
| 25 | 25 |
| 26 | RTS | Request To Send |
| 26 | 26 |
| 27 | TxD | Transmit Data |
| 27 | 27 |
| 28 | Rx-GND | Receive Ground |
| 28 | 28 |
| 29 | DSR | Data Set Ready |
| 29 | 29 |
| 30 | RTS | Request To Send |
| 30 | 30 |
| 31 | TxD | Transmit Data |
| 31 | 31 |
| 32 | Rx-GND | Receive Ground |
| 32 | 32 |
| 33 | DSR | Data Set Ready |
| 33 | 33 |
| 34 | - | - |
| 34 | 34 |
| 35 | - | - |
| 35 | 1 |
| 36 | DTR | Data Terminal Ready |
| 36 | 2 |
| 37 | Tx-GND | Transmit Ground |
| 37 | 3 |
| 38 | RxD | Receive Data |
| 38 | 4 |
| 39 | CTS | Clear To Send |
| 39 | 5 |
| 40 | DTR | Data Terminal Ready |
| 40 | 6 |
| 41 | Tx-GND | Transmit Ground |
| 41 | 7 |
| 42 | RxD | Receive Data |
| 42 | 8 |
| 43 | CTS | Clear To Send |
| 43 | 9 |
| 44 | DTR | Data Terminal Ready |
| 44 | 10 |
| 45 | Tx-GND | Transmit Ground |
| 45 | 11 |
| 46 | RxD | Receive Data |
| 46 | 12 |
| 47 | CTS | Clear To Send |
| 47 | 13 |
| 48 | DTR | Data Terminal Ready |
| 48 | 14 |
| 49 | Tx-GND | Transmit Ground |
| 49 | 15 |
| 50 | RxD | Receive Data |
| 50 | 16 |
| 51 | CTS | Clear To Send |
| 51 | 17 |
| 52 | DTR | Data Terminal Ready |
| 52 | 18 |
| 53 | Tx-GND | Transmit Ground |
| 53 | 19 |
| 54 | RxD | Receive Data |
| 54 | 20 |
| 55 | CTS | Clear To Send |
| 55 | 21 |
| 56 | DTR | Data Terminal Ready |
| 56 | 22 |
| 57 | Tx-GND | Transmit Ground |
| 57 | 23 |
| 58 | RxD | Receive Data |
| 58 | 24 |
| 59 | CTS | Clear To Send |
| 59 | 25 |
1 | 60 | DTR | Data Terminal Ready | 2 | 60 | 26 |
| 61 | Tx-GND | Transmit Ground |
| 61 | 27 |
| 62 | RxD | Receive Data |
| 62 | 28 |
| 63 | CTS | Clear To Send |
| 63 | 29 |
| 64 | DTR | Data Terminal Ready |
| 64 | 30 |
| 65 | Tx-GND | Transmit Ground |
| 65 | 31 |
| 66 | RxD | Receive Data |
| 66 | 32 |
| 67 | CTS | Clear To Send |
| 67 | 33 |
| 68 | - | - |
| 68 | 34 |
The Cisco 3640 Gatekeeper Cable connects to the signal harness with a three-legged cable (72-1646-xx) as shown in Figure 11. This cable connects the gatekeeper shelf connector Console 0 on the panel side and the gatekeeper shelf connectors Ethernet 0 and Ethernet 1 on the signal harness side as shown in Table 14.
Cisco AccessPath-VS3 configuration | Signal Harness Connector for Gatekeeper Shelf 1 | Signal Harness Connector for Gatekeeper Shelf 2 |
---|---|---|
Midrange | J20 | J22 |
High End | J14 | J16 |
High End Extended | J28 | J30 |
RJ-45 Plug | Shelf Connection | RJ-45 Pin | Twisted Pair | Signal | Description | 25-Pin |
---|---|---|---|---|---|---|
1 (Light blue) | Console | 1 | 4 | - | - | - |
|
| 2 |
| CON DSR | Console Data Set Ready | 8 |
|
| 3 | 3 | CON Rx | Console Receive | 6 |
|
| 4 |
| CON Rx_GND | Console Receive Ground | 19 |
|
| 5 | 2 | CON Tx_GND | Console Transmit Ground | 20 |
|
| 6 |
| CON Tx | Console Transmit | 7 |
|
| 7 | 1 | CON DTR | Console Data Terminal Ready | 21 |
|
| 8 |
| - | - | - |
2 (Yellow) | 10/100BaseT | 1 | 2 | ETH-1 Tx+ | Ethernet Transmit + | 1 |
|
| 2 |
| ETH-1 Tx- | Ethernet Transmit - | 14 |
|
| 3 | 1 | ETH-1 Rx+ | Ethernet Receive + | 3 |
|
| 6 |
| ETH-1 Rx- | Ethernet Receive - | 16 |
3 (Yellow) | 10BaseT | 1 | 2 | ETH-2 Tx+ | Ethernet Transmit + | 25 |
|
| 2 |
| ETH-2 Tx- | Ethernet Transmit - | 13 |
|
| 3 | 1 | ETH-2 Rx+ | Ethernet Receive + | 23 |
|
| 6 |
| ETH-2 Rx- | Ethernet Receive - | 11 |
This section lists the pinouts for ports on the supervisor engine module of the Cisco Catalyst 5002 Switch Shelf. All pins not specifically listed are not connected. Following is a list of the signal summaries contained in this section:
The Cisco Catalyst 5002 Switch Shelf's Ethernet switching cables (Figure 12) connect from the Fast Ethernet ports on the Cisco Catalyst 5002 Switch Shelf to J56 and J57 on the signal harness. These cables provide Ethernet switching connections to the Cisco AS5300 Access VoIP Shelves. (See Figure 12 and Table 16.)
RJ-45 Plug | Shelf Connection | RJ-45 Pin | Twisted Pair | Signal | Description | 50 Pin |
---|---|---|---|---|---|---|
1 (Yellow) | Port 1 | 1 | 2 | Tx+ | Transmit + | 1 |
2 | 2 | Tx- | Transmit - | 26 | ||
3 | 1 | Rx+ | Receive + | 2 | ||
6 | 1 | Rx- | Receive - | 27 | ||
2 (Yellow) | Port 2 | 1 | 2 | Tx+ | Transmit + | 3 |
2 | 2 | Tx- | Transmit - | 28 | ||
3 | 1 | Rx+ | Receive + | 4 | ||
6 | 1 | Rx- | Receive - | 29 | ||
3 (Yellow) | Port 3 | 1 | 2 | Tx+ | Transmit + | 5 |
2 | 2 | Tx- | Transmit - | 30 | ||
3 | 1 | Rx+ | Receive + | 6 | ||
6 | 1 | Rx- | Receive - | 31 | ||
4 (Yellow) | Port 4 | 1 | 2 | Tx+ | Transmit + | 7 |
2 | 2 | Tx- | Transmit - | 32 | ||
3 | 1 | Rx+ | Receive + | 8 | ||
6 | 1 | Rx- | Receive - | 33 | ||
5 (Yellow) | Port 5 | 1 | 2 | Tx+ | Transmit + | 9 |
2 | 2 | Tx- | Transmit - | 34 | ||
3 | 1 | Rx+ | Receive + | 10 | ||
6 | 1 | Rx- | Receive - | 35 | ||
6 (Yellow) | Port 6 | 1 | 2 | Tx+ | Transmit + | 11 |
2 | 2 | Tx- | Transmit - | 36 | ||
3 | 1 | Rx+ | Receive + | 12 | ||
6 | 1 | Rx- | Receive - | 37 | ||
7 (Yellow) | Port 7 | 1 | 2 | Tx+ | Transmit + | 13 |
2 | 2 | Tx- | Transmit - | 38 | ||
3 | 1 | Rx+ | Receive + | 14 | ||
6 | 1 | Rx- | Receive - | 39 | ||
8 (Yellow) | Port 8 | 1 | 2 | Tx+ | Transmit + | 15 |
2 | 2 | Tx- | Transmit - | 40 | ||
3 | 1 | Rx+ | Receive + | 16 | ||
6 | 1 | Rx- | Receive - | 41 | ||
9 (Yellow) | Port 9 | 1 | 2 | Tx+ | Transmit + | 17 |
2 | 2 | Tx- | Transmit - | 42 | ||
3 | 1 | Rx+ | Receive + | 18 | ||
6 | 1 | Rx- | Receive - | 43 | ||
10 (Yellow) | Port 10 | 1 | 2 | Tx+ | Transmit + | 19 |
2 | 2 | Tx- | Transmit - | 44 | ||
3 | 1 | Rx+ | Receive + | 20 | ||
6 | 1 | Rx- | Receive - | 45 | ||
11 (Yellow) | Port 11 | 1 | 2 | Tx+ | Transmit + | 21 |
2 | 2 | Tx- | Transmit - | 46 | ||
3 | 1 | Rx+ | Receive + | 22 | ||
6 | 1 | Rx- | Receive - | 47 | ||
12 (Yellow) | Port 12 | 1 | 2 | Tx+ | Transmit + | 23 |
2 | 2 | Tx- | Transmit - | 48 | ||
3 | 1 | Rx+ | Receive + | 24 | ||
6 | 1 | Rx- | Receive - | 49 |
The Cisco Catalyst 5002 Switch Shelf's Console/Ethernet cables (Figure 13) connect from console and Fast Ethernet ports on the Cisco Catalyst 5002 Switch Shelf's Supervisor Module to J55 on the signal harness.
This cable connects the Cisco Catalyst 5002 Switch Shelf to the Cisco 3640 System Controller for console management. (See Figure 13 and Table 17.)
RJ-45 Plug | Shelf Connection | RJ-45 Pin | Twisted Pair | Signal | Description | 25-Pin |
---|---|---|---|---|---|---|
1 (Light blue) | Console | 1 | 4 | Unused | - | - |
2 | CON DSR | Console Data Set Ready | 8 | |||
3 | 3 | CON Rx | Console Receive | 6 | ||
4 | CON Rx_GND | Console Receive Ground | 19 | |||
5 | 2 | CON Tx_GND | Console Transmit Ground | 20 | ||
6 | CON Tx | Console Transmit | 7 | |||
7 | 1 | CON DTR | Console Data Terminal Ready | 21 | ||
8 | Unused | - | - | |||
2 (Yellow) | Fast Ethernet 1 | 1 | 2 | ETH-1 Tx+ | Ethernet Transmit + | 1 |
2 | ETH-1 Tx- | Ethernet Transmit - | 14 | |||
3 | 1 | ETH-1 Rx+ | Ethernet Receive + | 3 | ||
6 | ETH-1 Rx- | Ethernet Receive - | 16 | |||
3 (Yellow) | Fast Ethernet 2 | 1 | 2 | ETH-1 Tx+ | Ethernet Transmit + | 25 |
2 | ETH-1 Tx- | Ethernet Transmit - | 13 | |||
3 | 1 | ETH-1 Rx+ | Ethernet Receive + | 23 | ||
6 | ETH-1 Rx- | Ethernet Receive - | 11 |
The cabinet interconnect cables are used to scale beyond 14 Cisco AS5300 Access VoIP Shelves. The primary cabinet contains the first 14 Cisco AS5300 Access VoIP Shelves, the 2 Cisco 7206 Router Shelves, the Cisco Catalyst 5002 Switch Shelf, and the Cisco 3640 System Controller. The secondary cabinet contains Cisco AS5300 Access VoIP Shelves 15 through 21.
These cables all connect from 1 signal harness to another to allow data communications between the cabinets.
There are 3 types of expansion cables, which are described in the following sections:
2 cabinet interconnect asynchronous cables (72-1460-xx) are used to connect the following:
Jack Number | 68 Pin SCSI | Signal | Description | Jack Number | 68 Pin SCSI | Twisted Pair |
---|---|---|---|---|---|---|
1 | 1 | - | - | 2 | 1 | 1 |
| 2 | RTS | Request To Send |
| 2 | 2 |
| 3 | TxD | Transmit Data |
| 3 | 3 |
| 4 | Rx-GND | Receive Ground |
| 4 | 4 |
| 5 | DSR | Data Set Ready |
| 5 | 5 |
| 6 | RTS | Request To Send |
| 6 | 6 |
| 7 | TxD | Transmit Data |
| 7 | 7 |
| 8 | Rx-GND | Receive Ground |
| 8 | 8 |
| 9 | DSR | Data Set Ready |
| 9 | 9 |
| 10 | RTS | Request To Send |
| 10 | 10 |
1 | 11 | TxD | Transmit Data | 2 | 11 | 11 |
| 12 | Rx-GND | Receive Ground |
| 12 | 12 |
| 13 | DSR | Data Set Ready |
| 13 | 13 |
| 14 | RTS | Request To Send |
| 14 | 14 |
| 15 | TxD | Transmit Data |
| 15 | 15 |
| 16 | Rx-GND | Receive Ground |
| 16 | 16 |
| 17 | DSR | Data Set Ready |
| 17 | 17 |
| 18 | RTS | Request To Send |
| 18 | 18 |
| 19 | TxD | Transmit Data |
| 19 | 19 |
| 20 | Rx-GND | Receive Ground |
| 20 | 20 |
| 21 | DSR | Data Set Ready |
| 21 | 21 |
| 22 | RTS | Request To Send |
| 22 | 22 |
| 23 | TxD | Transmit Data |
| 23 | 23 |
| 24 | Rx-GND | Receive Ground |
| 24 | 24 |
| 25 | DSR | Data Set Ready |
| 25 | 25 |
| 26 | RTS | Request To Send |
| 26 | 26 |
| 27 | TxD | Transmit Data |
| 27 | 27 |
| 28 | Rx-GND | Receive Ground |
| 28 | 28 |
| 29 | DSR | Data Set Ready |
| 29 | 29 |
| 30 | RTS | Request To Send |
| 30 | 30 |
| 31 | TxD | Transmit Data |
| 31 | 31 |
| 32 | Rx-GND | Receive Ground |
| 32 | 32 |
| 33 | DSR | Data Set Ready |
| 33 | 33 |
| 34 | - | - |
| 34 | 34 |
| 35 | - | - |
| 35 | 1 |
| 36 | DTR | Data Terminal Ready |
| 36 | 2 |
| 37 | Tx-GND | Transmit Ground |
| 37 | 3 |
| 38 | RxD | Receive Data |
| 38 | 4 |
| 39 | CTS | Clear To Send |
| 39 | 5 |
| 40 | DTR | Data Terminal Ready |
| 40 | 6 |
| 41 | Tx-GND | Transmit Ground |
| 41 | 7 |
| 42 | RxD | Receive Data |
| 42 | 8 |
| 43 | CTS | Clear To Send |
| 43 | 9 |
| 44 | DTR | Data Terminal Ready |
| 44 | 10 |
| 45 | Tx-GND | Transmit Ground |
| 45 | 11 |
| 46 | RxD | Receive Data |
| 46 | 12 |
| 47 | CTS | Clear To Send |
| 47 | 13 |
1 | 48 | DTR | Data Terminal Ready | 2 | 48 | 14 |
| 49 | Tx-GND | Transmit Ground |
| 49 | 15 |
| 50 | RxD | Receive Data |
| 50 | 16 |
| 51 | CTS | Clear To Send |
| 51 | 17 |
| 52 | DTR | Data Terminal Ready |
| 52 | 18 |
| 53 | Tx-GND | Transmit Ground |
| 53 | 19 |
| 54 | RxD | Receive Data |
| 54 | 20 |
| 55 | CTS | Clear To Send |
| 55 | 21 |
| 56 | DTR | Data Terminal Ready |
| 56 | 22 |
| 57 | Tx-GND | Transmit Ground |
| 57 | 23 |
| 58 | RxD | Receive Data |
| 58 | 24 |
| 59 | CTS | Clear To Send |
| 59 | 25 |
| 60 | DTR | Data Terminal Ready |
| 60 | 26 |
| 61 | Tx-GND | Transmit Ground |
| 61 | 27 |
| 62 | RxD | Receive Data |
| 62 | 28 |
| 63 | CTS | Clear To Send |
| 63 | 29 |
| 64 | DTR | Data Terminal Ready |
| 64 | 30 |
| 65 | Tx-GND | Transmit Ground |
| 65 | 31 |
| 66 | RxD | Receive Data |
| 66 | 32 |
| 67 | CTS | Clear To Send |
| 67 | 33 |
| 68 | - | - |
| 68 | 34 |
There are 2 types of cabinet interconnect Ethernet cables:
The 10BaseT cable connects the cabinet to provide an Ethernet connection for console management. (See Figure 15 and Table 19.)
9 Pin | Twisted Pair | Signal | Description | 25 Pin |
---|---|---|---|---|
1 | 1 | ME-5 Tx+ | Transmit + | 1 |
2 | ME-5 Rx+ | Receive + | 2 | |
4 | 2 | ME-6 Rx+ | Receive + | 4 |
5 | ME-6 Tx+ | Transmit + | 3 | |
6 | 3 | ME-5 Tx- | Transmit - | 14 |
7 | ME-5 Rx- | Receive - | 15 | |
8 | 4 | ME-6 Rx- | Receive - | 17 |
9 | ME-6 Tx- | Transmit - | 16 |
The 100/10BaseT cable for cabinet interconnect provides Fast Ethernet and Ethernet connectivity to transmit data from the Cisco AS5300 Access VoIP Shelves in the expansion cabinet to the Cisco Catalyst 5002 Switch Shelf and Cisco 7206 Router Shelves in the primary cabinet. (See Figure 16 and Table 20.)
Jack Number | 50 Pin | Signal | Description | Jack Number | 50 Pin | Twisted Pair |
---|---|---|---|---|---|---|
1 | 1 | Tx+ | Transmit + | 2 | 1 | 1 |
2 | Rx+ | Receive + | 2 | 2 | ||
3 | Tx+ | Transmit + | 3 | 3 | ||
4 | Rx+ | Receive + | 4 | 4 | ||
5 | Tx+ | Transmit + | 5 | 5 | ||
6 | Rx+ | Receive + | 6 | 6 | ||
7 | Tx+ | Transmit + | 7 | 7 | ||
8 | Rx+ | Receive + | 8 | 8 | ||
9 | Tx+ | Transmit + | 9 | 9 | ||
10 | Rx+ | Receive + | 10 | 10 | ||
11 | Tx+ | Transmit + | 11 | 11 | ||
12 | Rx+ | Receive + | 12 | 12 | ||
13 | Tx+ | Transmit + | 13 | 13 | ||
14 | Rx+ | Receive + | 14 | 14 | ||
15 | Tx+ | Transmit + | 15 | 15 | ||
16 | Rx+ | Receive + | 16 | 16 | ||
17 | Tx+ | Transmit + | 17 | 17 | ||
18 | Rx+ | Receive + | 18 | 18 | ||
19 | - | - | 19 | 19 | ||
20 | - | - | 20 | 20 | ||
21 | - | - | 21 | 21 | ||
22 | - | - | 22 | 22 | ||
23 | - | - | 23 | 23 | ||
1 | 24 | - | - | 2 | 24 | 24 |
25 | - | - | 25 | 25 | ||
26 | Tx- | Transmit - | 26 | 1 | ||
27 | Rx- | Receive - | 27 | 2 | ||
28 | Tx- | Transmit - | 28 | 3 | ||
29 | Rx- | Receive - | 29 | 4 | ||
30 | Tx- | Transmit - | 30 | 5 | ||
31 | Rx- | Receive - | 31 | 6 | ||
32 | Tx- | Transmit - | 32 | 7 | ||
33 | Rx- | Receive - | 33 | 8 | ||
34 | Tx- | Transmit - | 34 | 9 | ||
35 | Rx- | Receive - | 35 | 10 | ||
36 | Tx- | Transmit - | 36 | 11 | ||
37 | Rx- | Receive - | 37 | 12 | ||
38 | Tx- | Transmit - | 38 | 13 | ||
39 | Rx- | Receive - | 39 | 14 | ||
40 | Tx- | Transmit - | 40 | 15 | ||
41 | Rx- | Receive - | 41 | 16 | ||
42 | Tx- | Transmit - | 42 | 17 | ||
43 | Rx- | Receive - | 43 | 18 | ||
44 | - | - | 44 | 19 | ||
45 | - | - | 45 | 20 | ||
46 | - | - | 46 | 21 | ||
47 | - | - | 47 | 22 | ||
48 | - | - | 48 | 23 | ||
49 | - | - | 49 | 24 | ||
50 | - | - | 50 | 25 |
The following tables describe the port mapping for the entire Cisco AccessPath-VS3 system.
This mapping describes the connections between ports that are normally hidden by the cables within the signal harness. Use these tables for troubleshooting or for making connections between the appropriate ports without using the signal harness.
From Shelf | Port | To Shelf | Port |
---|---|---|---|
Cisco 7206 Router Shelf 1 | Fast Ethernet 5/0 | Cisco 7206 Router Shelf 1 | Fast Ethernet 0/0 |
Fast Ethernet 5/1 | Cisco 7206 Router Shelf 2 | Fast Ethernet 5/1 | |
Ethernet 5/2 | Cisco 3640 System Controller | Ethernet 1/0 | |
Ethernet 5/3 | Cisco AS5300 Access VoIP Shelf 1 | Ethernet 0 | |
Ethernet 5/4 | Cisco AS5300 Access VoIP Shelf 2 |
| |
Ethernet 5/5 | Cisco AS5300 Access VoIP Shelf 3 |
| |
Ethernet 5/6 | Cisco AS5300 Access VoIP Shelf 4 |
| |
Ethernet 5/7 | Cisco AS5300 Access VoIP Shelf 5 |
| |
Ethernet 5/8 | Cisco AS5300 Access VoIP Shelf 6 |
| |
Ethernet 5/9 | Cisco AS5300 Access VoIP Shelf 7 |
| |
Ethernet 5/10 | Cisco AS5300 Access VoIP Shelf 8 |
| |
Ethernet 5/11 | Cisco AS5300 Access VoIP Shelf 9 |
| |
Ethernet 5/12 | Cisco AS5300 Access VoIP Shelf 10/ Cisco 3640 Gatekeeper Shelf 2 | Ethernet O/ Ethernet 1/1 | |
Ethernet 5/13 | Cisco AS5300 Access VoIP Shelf 11/ Cisco 3640 Gatekeeper Shelf 1 | Ethernet O/ Ethernet 1/1 | |
Fast Ethernet 1/0 | Cisco Catalyst 5002 Switch Shelf | Port 1/1 | |
Cisco 7206 Router Shelf 2 | Fast Ethernet 5/0 | Cisco 7206 Router Shelf 2 | Fast Ethernet 0/0 |
Fast Ethernet 5/1 | Cisco 7206 Router Shelf 1 | Fast Ethernet 5/1 | |
Ethernet 5/2 | Cisco AS5300 Access VoIP Shelf 12 | Ethernet 0 | |
Ethernet 5/3 | Cisco AS5300 Access VoIP Shelf 13 |
| |
Ethernet 5/4 | Cisco AS5300 Access VoIP Shelf 14 |
| |
Ethernet 5/5 | Cisco AS5300 Access VoIP Shelf 15 |
| |
Ethernet 5/6 | Cisco AS5300 Access VoIP Shelf 16 |
| |
Ethernet 5/7 | Cisco AS5300 Access VoIP Shelf 17 |
| |
Ethernet 5/8 | Cisco AS5300 Access VoIP Shelf 18 |
| |
Ethernet 5/9 | Cisco AS5300 Access VoIP Shelf 19 |
| |
Ethernet 5/10 | Cisco AS5300 Access VoIP Shelf 20/ Cisco 3640 Gatekeeper Shelf 2 | Ethernet O/ Ethernet 1/1 | |
Ethernet 5/11 | Cisco AS5300 Access VoIP Shelf 21/ Cisco 3640 Gatekeeper Shelf 1 | Ethernet O/ Ethernet 1/1 | |
Fast Ethernet 1/0 | Cisco Catalyst 5002 Switch Shelf | Port 1/2 |
From Shelf | Port | To Shelf | Port |
---|---|---|---|
Cisco Catalyst 5002 Switch Shelf | Port 1/1 | Cisco 7206 Router Shelf 1 | Fast Ethernet 1/0 |
Port 1/2 | Cisco 7206 Router Shelf 2 | ||
Port 2/1 | Cisco 3640 System Controller | Ethernet 1/1 | |
Port 2/2 | Cisco AS5300 Access VoIP Shelf 1 | Fast Ethernet 0 | |
Port 2/3 | Cisco AS5300 Access VoIP Shelf 2 |
| |
Port 2/4 | Cisco AS5300 Access VoIP Shelf 3 |
| |
Port 2/5 | Cisco AS5300 Access VoIP Shelf 4 |
| |
Port 2/6 | Cisco AS5300 Access VoIP Shelf 5 |
| |
Port 2/7 | Cisco AS5300 Access VoIP Shelf 6 |
| |
Port 2/8 | Cisco AS5300 Access VoIP Shelf 7 |
| |
Port 2/9 | Cisco AS5300 Access VoIP Shelf 8 |
| |
Port 2/10 | Cisco AS5300 Access VoIP Shelf 9 |
| |
Port 2/11 | Cisco AS5300 Access VoIP Shelf 10/ Cisco 3640 Gatekeeper Shelf 2 | Fast Ethernet 0/ Ethernet 1/0 | |
Port 2/12 | Cisco AS5300 Access VoIP Shelf 11/ Cisco 3640 Gatekeeper Shelf 1 | Fast Ethernet 0/ Ethernet 1/0 | |
Port 2/13 | Cisco AS5300 Access VoIP Shelf 12 |
| |
Port 2/14 | Cisco AS5300 Access VoIP Shelf 13/ Cisco 3640 Gatekeeper Shelf 2 | Fast Ethernet 0/ Ethernet 1/0 | |
Port 2/15 | Cisco AS5300 Access VoIP Shelf 14/ Cisco 3640 Gatekeeper Shelf 1 | Fast Ethernet 0/ Ethernet 1/0 | |
Port 2/16 | Cisco AS5300 Access VoIP Shelf 15 |
| |
Port 2/17 | Cisco AS5300 Access VoIP Shelf 16 |
| |
Port 2/18 | Cisco AS5300 Access VoIP Shelf 17 |
| |
Port 2/19 | Cisco AS5300 Access VoIP Shelf 18 |
| |
Port 2/20 | Cisco AS5300 Access VoIP Shelf 19 |
| |
Port 2/21 | Cisco AS5300 Access VoIP Shelf 20/ Cisco 3640 Gatekeeper Shelf 2 | Fast Ethernet 0/ Ethernet 1/0 | |
Port 2/22 | Cisco AS5300 Access VoIP Shelf 21/ Cisco 3640 Gatekeeper Shelf 1 | Fast Ethernet 0/ Ethernet 1/0 |
From Shelf | Port | To Shelf | Port |
---|---|---|---|
Cisco 3640 System Controller | Async 1 | Cisco AS5300 Access VoIP Shelf 1 | Console |
Async 2 | Cisco AS5300 Access VoIP Shelf 2 | ||
Async 3 | Cisco AS5300 Access VoIP Shelf 3 | ||
Async 4 | Cisco AS5300 Access VoIP Shelf 4 | ||
Async 5 | Cisco AS5300 Access VoIP Shelf 5 | ||
Async 6 | Cisco AS5300 Access VoIP Shelf 6 | ||
Async 7 | Cisco AS5300 Access VoIP Shelf 7 | ||
Async 8 | Cisco 7206 Router Shelf 1 | ||
Async 9 | Cisco 7206 Router Shelf 2 | ||
Async 10 | Cisco 3640 Shelf 2 | - | |
Async 11 | Cisco Catalyst 5002 Switch Shelf/ Cisco 3640 Gatekeeper Shelf 1 | - | |
Async 12 | - | - | |
Async 13 | Cisco 3640 Gatekeeper Shelf 2 | - | |
Async 14 | Cisco 3640 Gatekeeper Shelf 1 | - | |
Async 15 | - | - | |
Async 16 | - | - | |
Async 17 | - | - | |
Async 18 | - | - | |
Async 19 | Cisco AS5300 Access VoIP Shelf 8 | Console | |
Async 20 | Cisco AS5300 Access VoIP Shelf 9 | ||
Async 21 | Cisco AS5300 Access VoIP Shelf 10/ Cisco 3640 Gatekeeper Shelf 2 | ||
Async 22 | Cisco AS5300 Access VoIP Shelf 11/ Cisco 3640 Gatekeeper Shelf 1 | ||
Async 23 | Cisco AS5300 Access VoIP Shelf 12 | ||
Async 24 | Cisco AS5300 Access VoIP Shelf 13 | ||
Async 25 | Cisco AS5300 Access VoIP Shelf 14 | ||
Async 26 | Cisco AS5300 Access VoIP Shelf 15 | ||
Async 27 | Cisco AS5300 Access VoIP Shelf 16 | ||
Async 28 | Cisco AS5300 Access VoIP Shelf 17 | ||
Async 29 | Cisco AS5300 Access VoIP Shelf 18 | ||
Async 30 | Cisco AS5300 Access VoIP Shelf 19 | ||
Async 31 | Cisco AS5300 Access VoIP Shelf 20 | ||
Async 32 | Cisco AS5300 Access VoIP Shelf 21 |
Posted: Wed Jul 17 03:45:04 PDT 2002
All contents are Copyright © 1992--2002 Cisco Systems, Inc. All rights reserved.
Important Notices and Privacy Statement.