Regulatory Compliance and Safety Information for the Cisco Secure ACS Appliance

Regulatory Compliance and Safety Information for the Cisco Secure ACS Appliance v3.2

This document provides regulatory compliance and safety information for Cisco Secure ACS Appliance v3.2, product number CSACSE-1111-K9. It contains the following sections:

• Documentation Road Map

• General Precautions

• Maintaining Safety with Electricity

• Preparing Your Site for Installation

• Regulatory Standards Compliance

• Safety Information

Documentation Road Map

Use this document in conjunction with the following documents:

•Cisco Secure ACS Appliance Installation and Setup Guide

•User Guide for Cisco Secure ACS Appliance

•Release Notes for Cisco Secure ACS Appliance

General Precautions

Observe the following general precautions for using and working with your Cisco Secure ACS Appliance:

•Keep the Cisco Secure ACS Appliance away from radiators and heat sources, and do not block its cooling vents.

•Do not spill food or liquids on the Cisco Secure ACS Appliance's components, and never operate the product in a wet environment. If the computer gets wet, contact Cisco's Technical Assistance Center.

•Do not push any objects into the openings of the Cisco Secure ACS Appliance's components. Doing so can cause fire or electric shock by shorting out interior components.

•Position system cables and power cables carefully; route system cables and the power cable and plug so that they cannot be stepped on or tripped over. Be sure that nothing rests on your system components' cables or power cable.

•Do not modify power cables or plugs. Consult a licensed electrician or your power company for site modifications. Always follow your local/national wiring rules.

Maintaining Safety with Electricity

Follow these guidelines when working on equipment powered by electricity:

•If any of the following conditions occur contact Cisco's Technical Assistance Center:

–The power cable, extension cable, or plug is damaged.

–An object has fallen into the product.

–The product has been exposed to water.

–The product has been dropped or damaged.

–The product does not operate correctly when you follow the operating instructions.

•Use the correct external power source. Operate the product only from the type of power source indicated on the electrical ratings label. If you are not sure of the type of power source required, consult Cisco's Technical Assistance Center or a local power company.

•To help prevent electric shock, plug the Cisco Secure ACS Appliance, components, and peripheral power cables into properly grounded electrical outlets. These cables are equipped with three-prong plugs to help ensure proper grounding. Do not use adapter plugs or remove the grounding prong from a cable.

•To help protect your Cisco Secure ACS Appliance from sudden, transient increases and decreases in electrical power, use a surge suppressor, line conditioner, or uninterruptable power supply (UPS).

•Do not modify power cables or plugs. Consult a licensed electrician or your power company for site modifications. Always follow your local/national wiring rules.

Protecting Against Electrostatic Discharge

Static electricity can harm delicate components inside your computer. To prevent static damage, discharge static electricity from your body before you touch any of your computer's electronic components. You can do so by touching an unpainted metal surface on the computer chassis.

As you continue to work inside the computer, periodically touch an unpainted metal surface to remove any static charge your body may have accumulated.

You can also take the following steps to prevent damage from electrostatic discharge (ESD):

•When unpacking a static-sensitive component from its shipping carton, do not remove the component from the antistatic packing material until you are ready to install the component in your computer. Just before unwrapping the antistatic packaging, be sure to discharge static electricity from your body.

•When transporting a sensitive component, first place it in an antistatic container or packaging.

•Handle all sensitive components in a static-safe area. If possible, use antistatic floor pads and workbench pads.

Preparing Your Site for Installation

This section describes the requirements your site must meet for safe installation and operation of your Cisco Secure ACS Appliance. Ensure that your site is properly prepared before beginning installation.

Environmental

When planning your site layout and equipment locations, keep in mind the precautions described in this section to help avoid equipment failures and reduce the possibility of environmentally caused shutdowns. If you are currently experiencing shutdowns or unusually high errors with your existing equipment, these precautions will help you isolate the cause of failures and prevent future problems.

Use the following precautions when planning the operating environment for your Cisco Secure ACS Appliance:

•Always follow the electrostatic discharge prevention procedures described in Chapter 2 of the Installation and Setup Guide for Cisco Secure ACS Appliance to avoid damage to equipment. Damage from static discharge can cause immediate or intermittent equipment failure.

•Make sure the chassis cover is secure. The chassis is designed to allow cooling air to flow effectively within it. An open chassis allows air leaks, which could interrupt and redirect the flow of cooling air from internal components.

•Electrical equipment generates heat. Ambient air temperature might not be adequate to cool equipment to acceptable operating temperatures without adequate circulation. Make sure that the room in which you operate has adequate air circulation.

Choosing a Site For Installation

Warning This unit is intended for installation in restricted access areas. A restricted access area is where access can only be gained by service personnel through the use of a special tool, lock and key, or other means of security, and is controlled by the authority responsible for the location.

•Choose a site with a dry, clean, well-ventilated and air-conditioned area.

•Choose a site that maintains an ambient temperature of 32 to 95 degrees F (0 to 35 degrees C).

Grounding the Cisco Secure ACS Appliance

Warning Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available.

Creating a Safe Environment

Follow these guidelines to create a safe operating environment:

•Keep tools and chassis components off the floor and away from foot traffic.

•Clear the area of possible hazards, such as moist floors, ungrounded power extension cables, and missing safety grounds.

•Keep the area around the chassis free from dust and foreign conductive material (such as metal flakes from nearby construction activity).

Precautions for Rack-Mounting

Observe the following precautions for rack stability and safety. Also refer to the Installation and Setup Guide for Cisco Secure ACS Appliance and any installation documentation accompanying the rack for specific warning and/or caution statements and procedures.

Servers, storage systems, and appliances are considered to be components in a rack. Thus, "component" refers to any server, storage system, or appliance, as well as to various peripherals or supporting hardware.

•Do not move large racks by yourself. Due to the height and weight of the rack, a minimum of two people are needed to accomplish this task.

•Make sure that the rack is level and stable before extending a component from the rack.

•Do not overload the AC supply branch circuit that provides power to the rack. The total rack load should not exceed 80 percent of the branch circuit rating.

•Ensure that proper airflow is provided to components in the rack.

•Do not step on or stand on any system/component when servicing other system/components in a rack.

Warning After installing system/components in a rack, never pull more than one component out of the rack on its slide assemblies at one time. The weight of more than one extended component could cause the rack to tip over and injure someone.

To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to ensure that the system remains stable. The following guidelines are provided to ensure your safety:

•This unit should be mounted at the bottom of the rack if it is the only unit in the rack.

•When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the heaviest component at the bottom of the rack.

•If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in the rack.

Precautions for Products With Modems, Telecommunications, or Local Area Network Options.

Observe the following guidelines when working with options:

•Do not connect or use a modem or telephone during a lightning storm. There may be a risk of electrical shock from lightning.

•Never connect or use a modem or telephone in a wet environment.

•Do not plug a modem or telephone cable into the Ethernet connector.

Regulatory Standards Compliance

This section includes the regulatory compliance, safety, and EMC standards. It also lists the warnings applicable to different countries.

Table 1 lists the regulatory standards compliance specifications.

European Community, Switzerland, Norway, Iceland and Liechtenstein

Declaration of Conformity with Regard to the Directives 73/23/EEC and 89/336/EEC as amended by Directive 93/68/EEC


Deutsch:	Dieses Ger�t entspricht den wesentlichen Anforderungen und weiteren Bestimmungen der Richtlinien 73/23/EWG und 89/336/EWG mit der Erg�nzung durch Richtlinie 93/68/EWG.
Dansk:	Dette udstyr er i overensstemmelse med de ufravigelige hensyn og andre bestemmelser i direktiv 73/23/EEC og 89/336/EEC som �ndred i direktiv 93/68/EEC.
English:	This equipment is in compliance with the essential requirements and other provisions of Directives 73/23/EEC and 89/336/EEC as amended by Directive 93/68/EEC.
Espa�ol:	Este equipo cumple con los requisitos esenciales y otras disposiciones de las Directrices 73/23/EEC y 89/336/EEC de acuerdo a las modificaciones de la Directriz 93/68/EEC.

Fran�ais:	Cet appareil remplit les principales conditions requises et autres dispositions des Directives 73/23/EEC et 89/336/EEC, modifi�es par la Directive 93/68/EEC.
�slenska:	�essir b�na�ur samr�mist l�gbo�num kr�fum og ��rum �kv��um tilskipana 73/23/EBE og 89/336/EBE, me� breytingum skv. tilskipun 93/68/EBE.
Italiano:	Questa apparecchiatura � conforme ai requisiti essenziali e altre disposizioni delle Direttive 73/23/EEC e 89/336/EEC modificate con la Direttiva 93/68/EEC.
Nederlands:	Deze apparatuur voldoet aan de belangrijkste eisen en andere voorzieningen van richtlijnen 73/23/EEC en 89/336/EEC zoals gewijzigd door richtlijn 93/68/EEC.
Norsk:	Dette utstyret samsvarer med de vesentligste kravene og andre regler i direktivene 73/23/EEC og 89/336/EEC samt i tilleggsdirektiv 93/68/EEC.
Portugu�s:	Este equipamento satisfaz os requisitos essenciais e outras provis�es das Directivas 73/23/EEC e 89/336/EEC, conforme amendados pela Directiva 93/68/EEC.
	CSACSE-1111-K9
Suomalainen:	T�m� laite on direktiivien 73/23/ETY ja 89/336/ETY (kuten muutettu direktiiviss� 93/68/ETY) keskeisten vaatimusten ja m��r�ysten mukainen.
Svenska:	Denna utrustning uppfyller de v�sentliga kraven och andra villkor i direktiven 73/23/EEC och 89/336/EEC enligt �ndringarna i direktiv 93/68/EEC.

The Declaration of Conformity related to this product can be found at the following URL:

http://tools.cisco.com/cse/prdapp/jsp/externalsearch.do?action=externalsearch&page=external_search

Table 1 Regulatory Standards Compliance
Item	Description
Regulatory Compliance	Products with the CE Marking indicate compliance with the 89/336/EEC, 73/23EEC directives, which includes the following safety and EMC standards.
Safety	UL 60950 CSA-C22.2 No. 60950 EN 60950 IEC 60950
EMC	FCC Part 15 (CFR 47) Class A ICEC-003 Class A EN 55022 Class A CISPR22 Class A AS/NZS 3548 Class A CNS 13438 Class A VCCI Class A EN55024 EN50082-1 EN 61000-3-1 EN 61000-3-2 EN 61000-3-3

EMC Environmental Conditions in the European Union

This equipment is intended to operate under the following environmental conditions with respect to EMC:

•A separate defined location under the user's control.

•Earthing and bonding shall meet the requirements of ETS 300 253 or CCITT K27.

•Where applicable, AC power distribution shall be one of the following types: TN-S and TN-C [as defined in IEC 364-3].

In addition, if equipment is operated in a domestic environment, interference may occur.

EMC Class A Warning Statements

FCC Class A

Warning Modifying the equipment without Cisco's authorization may result in the equipment no longer complying with FCC requirements for Class A or Class B digital devices. In that event, your right to use the equipment may be limited by FCC regulations and you may be required to correct any interference to radio or television communications at your own expense.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Canada Class A

Warning This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil num�rique de la classe A est conforme � la norme NMB-003 du Canada.

CISPR 22 Class A

This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Japan VCCI Class A

Warning This is a Class A product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment (VCCI). If this equipment is used in a domestic environment, radio disturbance may arise. When such trouble occurs, the user may be required to take corrective actions.

Taiwan (BSMI) Class A

Warning This is a Class A Information Product, when used in residential environment, it may cause radio frequency interference, under such circumstances, the user may be requested to take appropriate countermeasures.

Hungary Class A

Warning This equipment is a Class A product and should be used and installed properly according to the Hungarian EMC Class A requirements (MSZEN55022). The Class A equipment is derived for typical commercial establishments for which special conditions of installation and protection distance are used.

Figyelmeztet�s a felhaszn�l�i k�zik�nyv sz�m�ra: Ez a berendez�s "A" oszt�ly� term�k, felhaszn�l�s�ra �s �zembe helyez�s�re a magyar EMC "A" oszt�ly� k�vetelm�nyeknek (MSZ EN 55022) megfeleloen ker�lhet sor, illetve ezen "A" oszt�ly� berendez�sek csak megfelelo kereskedelmi forr�sb�l sz�rmazhatnak, amelyek biztos�tj�k a megfelelo speci�lis �zembe helyez�si k�r�lm�nyeket �s biztons�gos �zemel�si t�vols�gok alkalmaz�s�t.

Korean Class A

Translation: Class A Device This device is registered for EMC requirements for industrial use. The seller or buyer should be aware of this. If this type was sold or purchased by mistake, it should be replaced with a residential-use type

Safety Information

This section includes translations in multiple languages of the warnings that may appear in the Cisco Secure ACS Appliance product documents. Before working on equipment, be aware of the hazards involved with electrical circuitry and standard safety practices to prevent accidents.

Installation Instruction Warning


Warning Read the installation instructions before you connect the system to its power source.
Waarschuwing	Raadpleeg de installatie-aanwijzingen voordat u het systeem met de voeding verbindt.
Varoitus	Lue asennusohjeet ennen j�rjestelm�n yhdist�mist� virtal�hteeseen.
Attention	Avant de brancher le syst�me sur la source d'alimentation, consulter les directives d'installation.
Warnung	Lesen Sie die Installationsanweisungen, bevor Sie das System an die Stromquelle anschlie�en.
Avvertenza	Consultare le istruzioni di installazione prima di collegare il sistema all'alimentatore.
Advarsel	Les installasjonsinstruksjonene f�r systemet kobles til str�mkilden.
Aviso	Leia as instru��es de instala��o antes de ligar o sistema � sua fonte de energia.
�Advertencia!	Ver las instrucciones de instalaci�n antes de conectar el sistema a la red de alimentaci�n.
Varning!	L�s installationsanvisningarna innan du kopplar systemet till dess str�mf�rs�rjningsenhet.

Service Warning


Warning Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Waarschuwing	Deze apparatuur mag alleen worden ge�nstalleerd, vervangen of hersteld door bevoegd geschoold personeel.
Varoitus	T�m�n laitteen saa asentaa, vaihtaa tai huoltaa ainoastaan koulutettu ja laitteen tunteva henkil�kunta.
Attention	Il est vivement recommand� de confier l'installation, le remplacement et la maintenance de ces �quipements � des personnels qualifi�s et exp�riment�s.
Warnung	Das Installieren, Ersetzen oder Bedienen dieser Ausr�stung sollte nur geschultem, qualifiziertem Personal gestattet werden.
Avvertenza	Questo apparato pu� essere installato, sostituito o mantenuto unicamente da un personale competente.
Advarsel	Bare oppl�rt og kvalifisert personell skal foreta installasjoner, utskiftninger eller service p� dette utstyret.
Aviso	Apenas pessoal treinado e qualificado deve ser autorizado a instalar, substituir ou fazer a revis�o deste equipamento.
�Advertencia!	Solamente el personal calificado debe instalar, reemplazar o utilizar este equipo.
Varning!	Endast utbildad och kvalificerad personal b�r f� till�telse att installera, byta ut eller reparera denna utrustning.

Product Disposal Warning


Warning Ultimate disposal of this product should be handled according to all national laws and regulations.
Waarschuwing	Het uiteindelijke wegruimen van dit product dient te geschieden in overeenstemming met alle nationale wetten en reglementen.
Varoitus	T�m� tuote on h�vitett�v� kansallisten lakien ja m��r�ysten mukaisesti.
Attention	La mise au rebut ou le recyclage de ce produit sont g�n�ralement soumis � des lois et/ou directives de respect de l'environnement. Renseignez-vous aupr�s de l'organisme comp�tent.
Warnung	Die Entsorgung dieses Produkts sollte gem�� allen Bestimmungen und Gesetzen des Landes erfolgen.
Avvertenza	Lo smaltimento di questo prodotto deve essere eseguito secondo le leggi e regolazioni locali.
Advarsel	Endelig kassering av dette produktet skal v�re i henhold til alle relevante nasjonale lover og bestemmelser.
Aviso	Deitar fora este produto em conformidade com todas as leis e regulamentos nacionais.
�Advertencia!	Al deshacerse por completo de este producto debe seguir todas las leyes y reglamentos nacionales.
Varning!	Vid deponering hanteras produkten enligt g�llande lagar och best�mmelser.

Jewelry Removal Warning


Warning Before working on equipment that is connected to power lines, remove jewelry (including rings, necklaces, and watches). Metal objects will heat up when connected to power and ground and can cause serious burns or weld the metal object to the terminals.
Waarschuwing	Alvorens aan apparatuur te werken die met elektrische leidingen is verbonden, sieraden (inclusief ringen, kettingen en horloges) verwijderen. Metalen voorwerpen worden warm wanneer ze met stroom en aarde zijn verbonden, en kunnen ernstige brandwonden veroorzaken of het metalen voorwerp aan de aansluitklemmen lassen.
Varoitus	Ennen kuin ty�skentelet voimavirtajohtoihin kytkettyjen laitteiden parissa, ota pois kaikki korut (sormukset, kaulakorut ja kellot mukaan lukien). Metalliesineet kuumenevat, kun ne ovat yhteydess� s�hk�virran ja maan kanssa, ja ne voivat aiheuttaa vakavia palovammoja tai hitsata metalliesineet kiinni liit�nt�napoihin.
Attention	Avant d'acc�der � cet �quipement connect� aux lignes �lectriques, �ter tout bijou (anneaux, colliers et montres compris). Lorsqu'ils sont branch�s � l'alimentation et reli�s � la terre, les objets m�talliques chauffent, ce qui peut provoquer des blessures graves ou souder l'objet m�tallique aux bornes.
Warnung	Vor der Arbeit an Ger�ten, die an das Netz angeschlossen sind, jeglichen Schmuck (einschlie�lich Ringe, Ketten und Uhren) abnehmen. Metallgegenst�nde erhitzen sich, wenn sie an das Netz und die Erde angeschlossen werden, und k�nnen schwere Verbrennungen verursachen oder an die Anschlu�klemmen angeschwei�t werden.
Avvertenza	Prima di intervenire su apparecchiature collegate alle linee di alimentazione, togliersi qualsiasi monile (inclusi anelli, collane, braccialetti ed orologi). Gli oggetti metallici si riscaldano quando sono collegati tra punti di alimentazione e massa: possono causare ustioni gravi oppure il metallo pu� saldarsi ai terminali.
Advarsel	Fjern alle smykker (inkludert ringer, halskjeder og klokker) f�r du skal arbeide p� utstyr som er koblet til kraftledninger. Metallgjenstander som er koblet til kraftledninger og jord blir sv�rt varme og kan for�rsake alvorlige brannskader eller smelte fast til polene.
Aviso	Antes de trabalhar em equipamento que esteja ligado a linhas de corrente, retire todas as j�ias que estiver a usar (incluindo an�is, fios e rel�gios). Os objectos met�licos aquecer�o em contacto com a corrente e em contacto com a liga��o � terra, podendo causar queimaduras graves ou ficarem soldados aos terminais.
�Advertencia!	Antes de operar sobre equipos conectados a l�neas de alimentaci�n, quitarse las joyas (incluidos anillos, collares y relojes). Los objetos de metal se calientan cuando se conectan a la alimentaci�n y a tierra, lo que puede ocasionar quemaduras graves o que los objetos met�licos queden soldados a los bornes.
Varning!	Tag av alla smycken (inklusive ringar, halsband och armbandsur) innan du arbetar p� utrustning som �r kopplad till kraftledningar. Metallobjekt hettas upp n�r de kopplas ihop med str�m och jord och kan f�rorsaka allvarliga br�nnskador; metallobjekt kan ocks� sammansvetsas med kontakterna.

Open Chasis Warning


Warning Before opening the chassis, disconnect the telephone-network cables to avoid contact with telephone-network voltages
Waarschuwing	Voordat u het frame opent, dient u de verbinding met het telefoonnetwerk te verbreken door de kabels te ontkoppelen om zo contact met telefoonnetwerk-spanningen te vermijden.
Varoitus	V�lt� joutumista kosketuksiin puhelinverkostoj�nnitteiden kanssa irrottamalla puhelinverkoston kaapelit ennen asennuspohjan aukaisemista.
Attention	Avant d'ouvrir le ch�ssis, d�brancher les c�bles du r�seau t�l�phonique afin d'�viter tout contact avec les tensions d'alimentation du r�seau t�l�phonique.
Warnung	Bevor Sie das Chassis �ffnen, ziehen Sie die Telefonnetzkabel aus der Verbindung, um Kontakt mit Telefonnetzspannungen zu vermeiden.
Avvertenza	Prima di aprire il telaio, scollegare i cavi della rete telefonica per evitare di entrare in contatto con la tensione di rete.
Advarsel	F�r kabinettet �pnes, skal kablene for telenettet kobles fra for � unng� � komme i kontakt med spenningen i telenettet.
Aviso	Antes de abrir o chassis, desligue os cabos da rede telef�nica para evitar contacto com a tens�o da respectiva rede.
�Advertencia!	Antes de abrir el chasis, desconectar el cableado dirigido a la red telef�nica para evitar contacto con voltajes de la propia red.
Varning!	Koppla loss ledningarna till telefonn�tet innan du �ppnar chassit s� att kontakten med telefonn�tssp�nningen bryts.

Battery Installation Warning


Warning There is the danger of explosion if the battery is replaced incorrectly. Replace the battery only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions.
Waarschuwing	Er is ontploffingsgevaar als de batterij verkeerd vervangen wordt. Vervang de batterij slechts met hetzelfde of een equivalent type dat door de fabrikant aanbevolen is. Gebruikte batterijen dienen overeenkomstig fabrieksvoorschriften weggeworpen te worden.
Varoitus	R�j�hdyksen vaara, jos akku on vaihdettu v��r��n akkuun. K�yt� vaihtamiseen ainoastaan saman- tai vastaavantyyppist� akkua, joka on valmistajan suosittelema. H�vit� k�ytetyt akut valmistajan ohjeiden mukaan.
Attention	Danger d'explosion si la pile n'est pas remplac�e correctement. Ne la remplacer que par une pile de type semblable ou �quivalent, recommand�e par le fabricant. Jeter les piles usag�es conform�ment aux instructions du fabricant.
Warnung	Bei Einsetzen einer falschen Batterie besteht Explosionsgefahr. Ersetzen Sie die Batterie nur durch den gleichen oder vom Hersteller empfohlenen Batterietyp. Entsorgen Sie die benutzten Batterien nach den Anweisungen des Herstellers.
Avvertenza	Pericolo di esplosione se la batteria non � installata correttamente. Sostituire solo con una di tipo uguale o equivalente, consigliata dal produttore. Eliminare le batterie usate secondo le istruzioni del produttore.
Advarsel	Det kan v�re fare for eksplosjon hvis batteriet skiftes p� feil m�te. Skift kun med samme eller tilsvarende type som er anbefalt av produsenten. Kasser brukte batterier i henhold til produsentens instruksjoner.
Aviso	Existe perigo de explos�o se a bateria for substitu�da incorrectamente. Substitua a bateria por uma bateria igual ou de um tipo equivalente recomendado pelo fabricante. Destrua as baterias usadas conforme as instru��es do fabricante.
�Advertencia!	Existe peligro de explosi�n si la bater�a se reemplaza de manera incorrecta. Reemplazar la bater�a exclusivamente con el mismo tipo o el equivalente recomendado por el fabricante. Desechar las bater�as gastadas seg�n las instrucciones del fabricante.
Varning!	Explosionsfara vid felaktigt batteribyte. Ers�tt endast batteriet med samma batterityp som rekommenderas av tillverkaren eller motsvarande. F�lj tillverkarens anvisningar vid kassering av anv�nda batterier.

Power Cord Warning


Warning This unit might have more than one power cord. To reduce the risk of electrical shock, disconnect all power supply cords before servicing the unit.
Waarschuwing	Deze eenheid kan meer dan ��n elelektriciteitssnoer hebben. Om het risiko op een elektrische schok te reduceren, dient u alle elektriciteitssnoeren te ontkoppelen voordat u onderhoud op de eenheid uitvoert.
Varoitus	T�ss� laitteessa voi olla useampia virtajohtoja. S�hk�iskun v�ltt�miseksi on kaikki s�hk�johdot irrotettava ennen laitteen huoltoa.
Attention	Cette unit� doit �tre �quip�e de plusieurs cordons d'alimentation. Pour r�duire le risque de choc �lectrique, d�branchez tous les cordons d'alimentation avant toute op�ration de maintenance.
Warnung	Diese Einheit k�nnte mehr als ein Stromkabel haben. Um das Risiko eines elektrischen Schlags zu reduzieren, trennen Sie vor Bedienung der Einheit alle Stromkabel ab.
Avvertenza	Questa unit� pu� avere pi� di un cavo elettrico. Per ridurre il rischio di ricevere una scossa elettrica, staccate tutti i cavi elettrici prima di fare alcuna manutenzione nell'unit�.
Advarsel	Denne enheten kan v�re utstyrt med mer enn �n str�mledning. Forhindre fare for elektrisk st�t ved � trekke ut alle str�mst�psler f�r det utf�res service eller reparasjoner p� enheten.
Aviso	Este dispositivo pode possuir mais do que um cabo de alimenta��o de energia. Para reduzir o risco de choque el�ctrico, desconecte todos os cabos de alimenta��o de energia el�ctrica antes de reparar o dispositivo.
�Advertencia!	Esta unidad puede tener m�s de un cable de suministro el�ctrico. Para reducir el riesgo de electrocuci�n, desconecte todos los cables de suministro el�ctrico antes de reparar la unidad.
Varning!	Denna enhet �r eventuellt f�rsedd med mer �n en n�tsladd. F�rhindra risken av elektrisk st�t genom att koppla ur alla str�mf�rs�rjningssladdar innan du utf�r service eller reparationer p� enheten.

Ground Conductor Warning


Warning Never defeat the ground conductor or operate the equipment in the absence of a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if you are uncertain that suitable grounding is available.
Waarschuwing	De aardingsleiding mag nooit buiten werking gesteld worden en de apparatuur mag nooit bediend worden zonder dat er een op de juiste wijze ge�nstalleerde aardingsleiding aanwezig is. Neem contact op met de bevoegde instantie voor elektrische inspecties of met een elektricien als u er niet zeker van bent dat er voor passende aarding gezorgd is.
Varoitus	�l� koskaan ohita maajohdinta tai k�yt� laitteita ilman oikein asennettua maajohdinta. Ota yhteytt� asianmukaiseen s�hk�tarkastusviranomaiseen tai s�hk�asentajaan, jos olet ep�varma maadoituksen sopivuudesta.
Attention	Ne jamais rendre inop�rant le conducteur de masse ni utiliser l'�quipement sans un conducteur de masse ad�quatement install�. En cas de doute sur la mise � la masse appropri�e disponible, s'adresser � l'organisme responsable de la s�curit� �lectrique ou � un �lectricien.
Warnung	Auf keinen Fall den Erdungsleiter unwirksam machen oder das Ger�t ohne einen sachgerecht installierten Erdungsleiter verwenden. Wenn Sie sich nicht sicher sind, ob eine sachgerechte Erdung vorhanden ist, wenden Sie sich an den zust�ndigen elektrischen Fachmann oder einen Elektriker.
Avvertenza	Non escludere mai il conduttore di protezione n� usare l'apparecchiatura in assenza di un conduttore di protezione installato in modo corretto. Se non si sa con certezza che � disponibile un collegamento di messa a terra adeguato, esaminare le Norme CEI pertinenti o rivolgersi a un elettricista qualificato.
Advarsel	Omg� aldri jordingslederen og bruk aldri utstyret uten riktig montert jordingsleder. Ta kontakt med det riktige organet for elektrisk inspeksjon eller en elektriker hvis du er usikker p� om det finnes velegnet jording.
Aviso	Nunca anule o condutor � terra nem opere o equipamento sem ter um condutor � terra adequadamente instalado. Em caso de d�vida em rela��o ao sistema de liga��o � terra, contacte os servi�os locais de inspec��o el�ctrica ou um electricista qualificado.
�Advertencia!	No inhabilitar nunca el conductor de tierra ni hacer funcionar el equipo si no existe un conductor de tierra instalado correctamente. P�ngase en contacto con una autoridad apropiada de inspecci�n el�ctrica o con un electricista competente si no est� seguro de que hay una conexi�n a tierra adecuada.
Varning!	Koppla aldrig fr�n jordledningen och anv�nd aldrig utrustningen utan en p� l�mpligt s�tt installerad jordledning. Om det f�religger os�kerhet huruvida l�mplig jordning finns skall elektrisk besiktningsauktoritet eller elektriker kontaktas.

Safety Cover Warning


Warning The safety cover is an integral part of the product. Do not operate the unit without the safety cover installed. Operating the unit without the cover in place will invalidate the safety approvals and pose a risk of fire and electrical hazards.
Waarschuwing	Het beveiligingsdeksel is een integraal onderdeel van het product. Deze eenheid niet bedienen als het beveiligingsdeksel niet ge�nstalleerd is. Als het deksel niet op zijn plaats is tijdens de bediening, zal dit de veiligheidsaanbevelingen ongeldig maken en een risico op brand en elektrische gevaren vormen.
Varoitus	Suojakansi on t�rke� osa tuotetta. Yksikk�� ei saa k�ytt�� ilman suojakantta. Yksik�n k�ytt� ilman suojakantta mit�t�i turvallisuushyv�ksynn�t ja aiheuttaa tulipalon ja s�hk�iskun vaaran.
Attention	Le plateau de s�curit� est une partie int�grante du produit. Pour �viter tout risque de feu ou d'accident �lectrique, n'utilisez jamais l'unit� lorsque ce plateau n'est pas install�. Les garanties de s�curit� seraient annul�es.
Warnung	Die Sicherheitsabdeckung ist integraler Bestandteil des Produkts. Die Einheit darf nicht ohne installierte Sicherheitsabdeckung betrieben werden. Ein Betreiben der Einheit ohne korrekt installierte Abdeckung verst��t gegen die Sicherheitsnormen und f�hrt zu Brandgefahr sowie elektrischen Sicherheitsrisiken.
Avvertenza	Attenzione: Il pannello di sicurezza � parte integrante del prodotto. Non fate funzionare il sistema senza il pannello di sicurezza. Far funzionare il sistema senza il pannello invalider� le certificazioni di sicurezza e pu�'dare luogo a rischi di incendio e a cortocircuiti.
Advarsel	Dette sikkerhetsdekselet er en integral del av produktet. Enheten skal ikke brukes uten at sikkerhetsdekselet er montert. Bruk av enheten uten at sikkerhetsdekselet sitter p� plass, vil ugyldiggj�re sikkerhetsgodkjenningene, og kan dessuten utgj�re fare for brann og faremomenter i forbindelse med elektrisitet.
Aviso	A cobertura de seguran�a � uma parte integral do produto. N�o opere a unidade sem a respectiva cobertura de seguran�a instalada. Operar a unidade sem esta cobertura anular� as aprova��es de seguran�a e constituir� um risco de inc�ndio e perigo el�ctrico.
�Advertencia!	La cubierta de seguridad forma parte integral del producto. No haga funcionar este producto sin la cubierta de seguridad instalada, de lo contrario se invalidar�an las aprobaciones de seguridad y se correr�a el riesgo de incendio o de descargas el�ctricas.
Varning!	Skyddshuven �r en v�sentlig del av produkten. Anv�nd inte enheten utan installerad skyddshuv. Om enheten anv�nds utan skyddshuven p� plats upph�vs alla s�kerhetsgodk�nnanden och risk f�r brandfara och elektrisk fara f�religger.

Faceplate and Cover Panel Warning


Warning Blank faceplates and cover panels serve three important functions: they prevent exposure to hazardous voltages and currents inside the chassis; they contain electromagnetic interference (EMI) that might disrupt other equipment; and they direct the flow of cooling air through the chassis. Do not operate the system unless all cards, faceplates, front covers, and rear covers are in place.
Waarschuwing	Lege vlakplaten en afdekpanelen vervullen drie belangrijke functies: ze voorkomen blootstelling aan gevaarlijke voltages en stroom binnenin het frame, ze bevatten elektromagnetische storing (EMI) hetgeen andere apparaten kan verstoren en ze leiden de stroom van koellucht door het frame. Het systeem niet bedienen tenzij alle kaarten, vlakplaten en afdekkingen aan de voor- en achterkant zich op hun plaats bevinden.
Varoitus	Tyhjill� tasolaikoilla ja suojapaneeleilla on kolme t�rke�� k�ytt�tarkoitusta: Ne suojaavat asennuspohjan sis�isille vaarallisille j�nnitteille ja s�hk�virralle altistumiselta; ne pit�v�t sis�ll��n elektromagneettisen h�iri�n (EMI), joka voi h�irit� muita laitteita; ja ne suuntaavat tuuletusilman asennuspohjan l�pi. J�rjestelm�� ei saa k�ytt��, elleiv�t kaikki tasolaikat, etukannet ja takakannet ole kunnolla paikoillaan.
Attention	Ne jamais faire fonctionner le syst�me sans que l'int�gralit� des cartes, des plaques m�talliques et des panneaux avant et arri�re ne soient fix�s � leur emplacement. Ceux-ci remplissent trois fonctions essentielles : ils �vitent tout risque de contact avec des tensions et des courants dangereux � l'int�rieur du ch�ssis, ils �vitent toute diffusion d'interf�rences �lectromagn�tiques qui pourraient perturber le fonctionnement des autres �quipements, et ils canalisent le flux d'air de refroidissement dans le ch�ssis.
Warnung	Blanke Faceplates und Abdeckungen haben drei wichtigen Funktionen: (1) Sie sch�tzen vor gef�hrlichen Spannungen und Strom innerhalb des Chassis; (2) sie halten elektromagnetische Interferenzen (EMI) zur�ck, die andere Ger�te st�ren k�nnten; (3) sie lenken den k�hlenden Luftstrom durch das Chassis. Das System darf nur betrieben werden, wenn alle Karten, Faceplates, Voder- und R�ckabdeckungen an Ort und Stelle sind.
Avvertenza	Le piattaforme bianche e i panelli di protezione hanno tre funzioni importanti: Evitano l'esposizione a voltaggi e correnti elettriche pericolose nello chassis, trattengono le interferenze elettromagnetiche (EMI) che potrebbero scombussolare altri apparati e dirigono il flusso di aria per il raffreddamento attraverso lo chassis. Non mettete in funzione il sistema se le schede, le piattaforme, i panelli frontali e posteriori non sono in posizione.
Advarsel	Blanke ytterplater og deksler s�rger for tre viktige funksjoner: de forhindrer utsettelse for farlig spenning og str�m inni kabinettet; de inneholder elektromagnetisk forstyrrelse (EMI) som kan avbryte annet utstyr, og de dirigerer luftavkj�lingsstr�mmen gjennom kabinettet. Betjen ikke systemet med mindre alle kort, ytterplater, frontdeksler og bakdeksler sitter p� plass.
Aviso	As faces furadas e os pain�is de protec��o desempenham tr�s importantes fun��es: previnem contra uma exposi��o perigosa a voltagens e correntes existentes no interior do chassis; previnem contra interfer�ncia electromagn�tica (EMI) que poder� danificar outro equipamento; e canalizam o fluxo do ar de refrigera��o atrav�s do chassis. N�o dever� operar o sistema sem que todas as placas, faces, protec��es anteriores e posteriores estejam nos seus lugares.
�Advertencia!	Las placas frontales y los paneles de relleno cumplen tres funciones importantes: evitan la exposici�n a niveles peligrosos de voltaje y corriente dentro del chasis; reducen la interferencia electromagn�tica (EMI) que podr�a perturbar la operaci�n de otros equipos y dirigen el flujo de aire de enfriamiento a trav�s del chasis. No haga funcionar el sistema a menos que todas las tarjetas, placas frontales, cubiertas frontales y cubiertas traseras est�n en su lugar.
Varning!	Tomma framplattor och skyddspaneler har tre viktiga funktioner: de f�rhindrar att personer uts�tts f�r farlig sp�nning och str�m som finns inuti chassit; de inneh�ller elektromagnetisk interferens (EMI) som kan st�ra annan utrustning; och de styr riktningen p� kylluftsfl�det genom chassit. Anv�nd inte systemet om inte alla kort, framplattor, fram- och bakskydd �r p� plats.

Rack Mounting Warning


Warning To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to ensure that the system remains stable. The following guidelines are provided to ensure your safety:
	•This unit should be mounted at the bottom of the rack if it is the only unit in the rack. •When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the heaviest component at the bottom of the rack. •If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in the rack.
Waarschuwing	Om lichamelijk letsel te voorkomen wanneer u dit toestel in een rek monteert of het daar een servicebeurt geeft, moet u speciale voorzorgsmaatregelen nemen om ervoor te zorgen dat het toestel stabiel blijft. De onderstaande richtlijnen worden verstrekt om uw veiligheid te verzekeren: •Dit toestel dient onderaan in het rek gemonteerd te worden als het toestel het enige in het rek is. •Wanneer u dit toestel in een gedeeltelijk gevuld rek monteert, dient u het rek van onderen naar boven te laden met het zwaarste onderdeel onderaan in het rek. •Als het rek voorzien is van stabiliseringshulpmiddelen, dient u de stabilisatoren te monteren voordat u het toestel in het rek monteert of het daar een servicebeurt geeft.
Varoitus	Kun laite asetetaan telineeseen tai huolletaan sen ollessa telineess�, on noudatettava erityisi� varotoimia j�rjestelm�n vakavuuden s�ilytt�miseksi, jotta v�ltyt��n loukkaantumiselta. Noudata seuraavia turvallisuusohjeita: •Jos telineess� ei ole muita laitteita, aseta laite telineen alaosaan. •Jos laite asetetaan osaksi t�ytettyyn telineeseen, aloita kuormittaminen sen alaosasta kaikkein raskaimmalla esineell� ja siirry sitten sen yl�osaan. •Jos telinett� varten on vakaimet, asenna ne ennen laitteen asettamista telineeseen tai sen huoltamista siin�.
Attention	Pour �viter toute blessure corporelle pendant les op�rations de montage ou de r�paration de cette unit� en casier, il convient de prendre des pr�cautions sp�ciales afin de maintenir la stabilit� du syst�me. Les directives ci-dessous sont destin�es � assurer la protection du personnel : •Si cette unit� constitue la seule unit� mont�e en casier, elle doit �tre plac�e dans le bas. •Si cette unit� est mont�e dans un casier partiellement rempli, charger le casier de bas en haut en pla�ant l'�l�ment le plus lourd dans le bas. •Si le casier est �quip� de dispositifs stabilisateurs, installer les stabilisateurs avant de monter ou de r�parer l'unit� en casier.
Warnung	Zur Vermeidung von K�rperverletzung beim Anbringen oder Warten dieser Einheit in einem Gestell m�ssen Sie besondere Vorkehrungen treffen, um sicherzustellen, da� das System stabil bleibt. Die folgenden Richtlinien sollen zur Gew�hrleistung Ihrer Sicherheit dienen: •Wenn diese Einheit die einzige im Gestell ist, sollte sie unten im Gestell angebracht werden. •Bei Anbringung dieser Einheit in einem zum Teil gef�llten Gestell ist das Gestell von unten nach oben zu laden, wobei das schwerste Bauteil unten im Gestell anzubringen ist. •Wird das Gestell mit Stabilisierungszubeh�r geliefert, sind zuerst die Stabilisatoren zu installieren, bevor Sie die Einheit im Gestell anbringen oder sie warten.
Avvertenza	Per evitare infortuni fisici durante il montaggio o la manutenzione di questa unit� in un supporto, occorre osservare speciali precauzioni per garantire che il sistema rimanga stabile. Le seguenti direttive vengono fornite per garantire la sicurezza personale: •Questa unit� deve venire montata sul fondo del supporto, se si tratta dell'unica unit� da montare nel supporto. •Quando questa unit� viene montata in un supporto parzialmente pieno, caricare il supporto dal basso all'alto, con il componente pi� pesante sistemato sul fondo del supporto. •Se il supporto � dotato di dispositivi stabilizzanti, installare tali dispositivi prima di montare o di procedere alla manutenzione dell'unit� nel supporto.
Advarsel	Unng� fysiske skader under montering eller reparasjonsarbeid p� denne enheten n�r den befinner seg i et kabinett. V�r n�ye med at systemet er stabilt. F�lgende retningslinjer er gitt for � verne om sikkerheten: •Denne enheten b�r monteres nederst i kabinettet hvis dette er den eneste enheten i kabinettet. •Ved montering av denne enheten i et kabinett som er delvis fylt, skal kabinettet lastes fra bunnen og opp med den tyngste komponenten nederst i kabinettet. •Hvis kabinettet er utstyrt med stabiliseringsutstyr, skal stabilisatorene installeres f�r montering eller utf�ring av reparasjonsarbeid p� enheten i kabinettet.
Aviso	Para se prevenir contra danos corporais ao montar ou reparar esta unidade numa estante, dever� tomar precau��es especiais para se certificar de que o sistema possui um suporte est�vel. As seguintes directrizes ajud�-lo-�o a efectuar o seu trabalho com seguran�a: •Esta unidade dever� ser montada na parte inferior da estante, caso seja esta a �nica unidade a ser montada. •Ao montar esta unidade numa estante parcialmente ocupada, coloque os itens mais pesados na parte inferior da estante, arrumando-os de baixo para cima. •Se a estante possuir um dispositivo de estabiliza��o, instale-o antes de montar ou reparar a unidade.
�Advertencia!	Para evitar lesiones durante el montaje de este equipo sobre un bastidor, o posteriormente durante su mantenimiento, se debe poner mucho cuidado en que el sistema quede bien estable. Para garantizar su seguridad, proceda seg�n las siguientes instrucciones: •Colocar el equipo en la parte inferior del bastidor, cuando sea la �nica unidad en el mismo. •Cuando este equipo se vaya a instalar en un bastidor parcialmente ocupado, comenzar la instalaci�n desde la parte inferior hacia la superior colocando el equipo m�s pesado en la parte inferior. •Si el bastidor dispone de dispositivos estabilizadores, instalar �stos antes de montar o proceder al mantenimiento del equipo instalado en el bastidor.
Varning!	F�r att undvika kroppsskada n�r du installerar eller utf�r underh�llsarbete p� denna enhet p� en st�llning m�ste du vidta s�rskilda f�rsiktighets�tg�rder f�r att f�rs�kra dig om att systemet st�r stadigt. F�ljande riktlinjer ges f�r att trygga din s�kerhet: •Om denna enhet �r den enda enheten p� st�llningen skall den installeras l�ngst ned p� st�llningen. •Om denna enhet installeras p� en delvis fylld st�llning skall st�llningen fyllas nedifr�n och upp, med de tyngsta enheterna l�ngst ned p� st�llningen. •Om st�llningen �r f�rsedd med stabiliseringsdon skall dessa monteras fast innan enheten installeras eller underh�lls p� st�llningen.


Warning To avoid electric shock, do not connect safety extra-low voltage (SELV) circuits to telephone-network voltage (TNV) circuits. LAN ports contain SELV circuits, and WAN ports contain TNV circuits. Some LAN and WAN ports both use RJ-45 connectors. Use caution when connecting cables.
Waarschuwing	Om elektrische schokken te vermijden, mogen veiligheidscircuits met extra lage spanning (genaamd SELV = Safety Extra-Low Voltage) niet met telefoonnetwerkspanning (TNV) circuits verbonden worden. LAN (Lokaal netwerk) poorten bevatten SELV circuits en WAN (Regionaal netwerk) poorten bevatten TNV circuits. Sommige LAN en WAN poorten gebruiken allebei RJ-45 connectors. Ga voorzichtig te werk wanneer u kabels verbindt.
Varoitus	Jotta v�ltyt s�hk�iskulta, �l� kytke pienj�nnitteisi� SELV-suojapiirej� puhelinverkkoj�nnitett� (TNV) k�ytt�viin virtapiireihin. LAN-portit sis�lt�v�t SELV-piirej� ja WAN-portit puhelinverkkoj�nnitett� k�ytt�vi� piirej�. Osa sek� LAN- ett� WAN-porteista k�ytt�� RJ-45-liittimi�. Ole varovainen kytkiess�si kaapeleita.
Attention	Pour �viter une �lectrocution, ne raccordez pas les circuits de s�curit� basse tension (Safety Extra-Low Voltage ou SELV) � des circuits de tension de r�seau t�l�phonique (Telephone Network Voltage ou TNV). Les ports du r�seau local (LAN) contiennent des circuits SELV et les ports du r�seau longue distance (WAN) sont munis de circuits TNV. Certains ports LAN et WAN utilisent des connecteurs RJ-45. Raccordez les c�bles en prenant toutes les pr�cautions n�cessaires.
Warnung	Zur Vermeidung von Elektroschock die Sicherheits-Kleinspannungs-Stromkreise (SELV-Kreise) nicht an Fernsprechnetzspannungs-Stromkreise (TNV-Kreise) anschlie�en. LAN-Ports enthalten SELV-Kreise, und WAN-Ports enthalten TNV-Kreise. Einige LAN- und WAN-Ports verwenden auch RJ-45-Steckverbinder. Vorsicht beim Anschlie�en von Kabeln.
Avvertenza	Per evitare scosse elettriche, non collegare circuiti di sicurezza a tensione molto bassa (SELV) ai circuiti a tensione di rete telefonica (TNV). Le porte LAN contengono circuiti SELV e le porte WAN contengono circuiti TNV. Alcune porte LAN e WAN fanno uso di connettori RJ-45. Fare attenzione quando si collegano cavi.
Advarsel	Unng� � koble lavspenningskretser (SELV) til kretser for telenettspenning (TNV), slik at du unng�r elektrisk st�t. LAN-utganger inneholder SELV-kretser og WAN-utganger inneholder TNV-kretser. Det finnes b�de LAN-utganger og WAN-utganger som bruker RJ-45-kontakter. V�r forsiktig n�r du kobler kabler.
Aviso	Para evitar choques el�ctricos, n�o conecte os circuitos de seguran�a de baixa tens�o (SELV) aos circuitos de tens�o de rede telef�nica (TNV). As portas LAN cont�m circuitos SELV e as portas WAN cont�m circuitos TNV. Algumas portas LAN e WAN usam conectores RJ-45. Tenha o devido cuidado ao conectar os cabos.
�Advertencia!	Para evitar la sacudida el�ctrica, no conectar circuitos de seguridad de voltaje muy bajo (safety extra-low voltage = SELV) con circuitos de voltaje de red telef�nica (telephone network voltage = TNV). Los puertos de redes de �rea local (local area network = LAN) contienen circuitos SELV, y los puertos de redes de �rea extendida (wide area network = WAN) contienen circuitos TNV. En algunos casos, tanto los puertos LAN como los WAN usan conectores RJ-45. Proceda con precauci�n al conectar los cables.
Varning!	F�r att undvika elektriska st�tar, koppla inte s�kerhetskretsar med extra l�g sp�nning (SELV-kretsar) till kretsar med telefonn�tsp�nning (TNV-kretsar). LAN-portar inneh�ller SELV-kretsar och WAN-portar inneh�ller TNV-kretsar. Vissa LAN- och WAN-portar �r f�rsedda med RJ-45-kontakter. Iaktta f�rsiktighet vid anslutning av kablar.

SELV Circuit Warning

AC Power Disconnection Warning


Warning Before working on a chassis or working near power supplies, unplug the power cord on AC units.
Waarschuwing	Voordat u aan een frame of in de nabijheid van voedingen werkt, dient u bij wisselstroom toestellen de stekker van het netsnoer uit het stopcontact te halen.
Varoitus	Kytke irti vaihtovirtalaitteiden virtajohto ennen kuin teet mit��n asennuspohjalle tai ty�skentelet virtal�hteiden l�heisyydess�.
Attention	Avant de travailler sur un ch�ssis ou � proximit� d'une alimentation �lectrique, d�brancher le cordon d'alimentation des unit�s en courant alternatif.
Warnung	Bevor Sie an einem Chassis oder in der N�he von Netzger�ten arbeiten, ziehen Sie bei Wechselstromeinheiten das Netzkabel ab.
Avvertenza	Prima di lavorare su un telaio o intorno ad alimentatori, scollegare il cavo di alimentazione sulle unit� CA.
Advarsel	F�r det utf�res arbeid p� kabinettet eller det arbeides i n�rheten av str�mforsyningsenheter, skal str�mledningen trekkes ut p� vekselstr�msenheter.
Aviso	Antes de trabalhar num chassis, ou antes de trabalhar perto de unidades de fornecimento de energia, desligue o cabo de alimenta��o nas unidades de corrente alternada.
�Advertencia!	Antes de manipular el chasis de un equipo o trabajar cerca de una fuente de alimentaci�n, desenchufar el cable de alimentaci�n en los equipos de corriente alterna (CA).
Varning!	Innan du arbetar med ett chassi eller n�ra str�mf�rs�rjningsenheter skall du dra ur n�tsladden p� v�xelstr�msenheter.

Circuit Breaker (15A) Warning


Warning This product relies on the building's installation for short-circuit (overcurrent) protection. Ensure that a fuse or circuit breaker no larger than 120 VAC, 15A U.S. (240 VAC, 10A international) is used on the phase conductors (all current-carrying conductors).
Waarschuwing	Dit produkt is afhankelijk van de installatie van het gebouw voor kortsluit- (overstroom) beveiliging. Controleer of er een zekering of stroomverbreker van niet meer dan 120 Volt wisselstroom, 15 A voor de V.S. (240 Volt wisselstroom, 10 A internationaal) gebruikt wordt op de fasegeleiders (alle geleiders die stroom voeren).
Varoitus	T�m� tuote on riippuvainen rakennukseen asennetusta oikosulkusuojauksesta (ylivirtasuojauksesta). Varmista, ett� vaihevirtajohtimissa (kaikissa virroitetuissa johtimissa) k�ytet��n Yhdysvalloissa alle 120 voltin, 15 ampeerin ja monissa muissa maissa 240 voltin, 10 ampeerin sulaketta tai suojakytkint�.
Attention	Pour ce qui est de la protection contre les courts-circuits (surtension), ce produit d�pend de l'installation �lectrique du local. V�rifier qu'un fusible ou qu'un disjoncteur de 120 V alt., 15 A U.S. maximum (240 V alt., 10 A international) est utilis� sur les conducteurs de phase (conducteurs de charge).
Warnung	Dieses Produkt ist darauf angewiesen, da� im Geb�ude ein Kurzschlu�- bzw. �berstromschutz installiert ist. Stellen Sie sicher, da� eine Sicherung oder ein Unterbrecher von nicht mehr als 240 V Wechselstrom, 10 A (bzw. in den USA 120 V Wechselstrom, 15 A) an den Phasenleitern (allen stromf�hrenden Leitern) verwendet wird.
Avvertenza	Questo prodotto dipende dall'installazione dell'edificio per quanto riguarda la protezione contro cortocircuiti (sovracorrente). Verificare che un fusibile o interruttore automatico, non superiore a 120 VCA, 15 A U.S. (240 VCA, 10 A internazionale) sia stato usato nei fili di fase (tutti i conduttori portatori di corrente).
Advarsel	Dette produktet er avhengig av bygningens installasjoner av kortslutningsbeskyttelse (overstr�m). Kontroller at det brukes en sikring eller str�mbryter som ikke er st�rre enn 120 VAC, 15 A (USA) (240 VAC, 10 A internasjonalt) p� faselederne (alle str�mf�rende ledere).
Aviso	Este produto depende das instala��es existentes para protec��o contra curto-circuito (sobrecarga). Assegure-se de que um fus�vel ou disjuntor n�o superior a 240 VAC, 10A � utilizado nos condutores de fase (todos os condutores de transporte de corrente).
�Advertencia!	Este equipo utiliza el sistema de protecci�n contra cortocircuitos (o sobrecorrientes) del� propio edificio. Asegurarse de que se utiliza un fusible o interruptor autom�tico de no m�s de 240 voltios en corriente alterna (VAC), 10 amperios del est�ndar internacional (120 VAC, 15 amperios del est�ndar USA) en los hilos de fase (todos aqu�llos portadores de corriente).
Varning!	Denna produkt �r beroende av i byggnaden installerat kortslutningsskydd (�verstr�msskydd). Kontrollera att s�kring eller �versp�nningsskydd anv�nds p� fasledarna (samtliga str�mf�rande ledare) f�r internationellt bruk max. 240 V v�xelstr�m, 10 A (i USA max. 120 V v�xelstr�m, 15 A).

Grounded Equipment Warning


Warning This equipment is intended to be grounded. Ensure that the host is connected to earth ground during normal use.
Waarschuwing	Deze apparatuur hoort geaard te worden Zorg dat de host-computer tijdens normaal gebruik met aarde is verbonden.
Varoitus	T�m� laitteisto on tarkoitettu maadoitettavaksi. Varmista, ett� is�nt�laite on yhdistetty maahan normaalik�yt�n aikana.
Attention	Cet �quipement doit �tre reli� � la terre. S'assurer que l'appareil h�te est reli� � la terre lors de l'utilisation normale.
Warnung	Dieses Ger�t mu� geerdet werden. Stellen Sie sicher, da� das Host-Ger�t w�hrend des normalen Betriebs an Erde gelegt ist.
Avvertenza	Questa apparecchiatura deve essere collegata a massa. Accertarsi che il dispositivo host sia collegato alla massa di terra durante il normale utilizzo.
Advarsel	Dette utstyret skal jordes. Forviss deg om vertsterminalen er jordet ved normalt bruk.
Aviso	Este equipamento dever� estar ligado � terra. Certifique-se que o host se encontra ligado � terra durante a sua utiliza��o normal.
�Advertencia!	Este equipo debe conectarse a tierra. Asegurarse de que el equipo principal est� conectado a tierra durante el uso normal.
Varning!	Denna utrustning �r avsedd att jordas. Se till att v�rdenheten �r jordad vid normal anv�ndning.

Lightning Activity Warning


Warning Do not work on the system or connect or disconnect cables during periods of lightning activity.
Waarschuwing	Tijdens onweer dat gepaard gaat met bliksem, dient u niet aan het systeem te werken of kabels aan te sluiten of te ontkoppelen.
Varoitus	�l� ty�skentele j�rjestelm�n parissa �l�k� yhdist� tai irrota kaapeleita ukkosilmalla.
Attention	Ne pas travailler sur le syst�me ni brancher ou d�brancher les c�bles pendant un orage.
Warnung	Arbeiten Sie nicht am System und schlie�en Sie keine Kabel an bzw. trennen Sie keine ab, wenn es gewittert.
Avvertenza	Non lavorare sul sistema o collegare oppure scollegare i cavi durante un temporale con fulmini.
Advarsel	Utf�r aldri arbeid p� systemet, eller koble kabler til eller fra systemet n�r det tordner eller lyner.
Aviso	N�o trabalhe no sistema ou ligue e desligue cabos durante per�odos de mau tempo (trovoada).
�Advertencia!	No operar el sistema ni conectar o desconectar cables durante el transcurso de descargas el�ctricas en la atm�sfera.
Varning!	Vid �ska skall du aldrig utf�ra arbete p� systemet eller ansluta eller koppla loss kablar.

Power Disconnection Warning


Warning Before working on a system that has an on/off switch, turn OFF the power and unplug the power cord.
Waarschuwing	Voordat u aan een systeem werkt dat een aan/uit schakelaar heeft, dient u de stroomvoorziening UIT te schakelen en de stekker van het netsnoer uit het stopcontact te halen.
Varoitus	Ennen kuin teet mit��n sellaiselle j�rjestelm�lle, jossa on kaksiasentokytkin, katkaise siit� virta ja kytke virtajohto irti.
Attention	Avant de travailler sur un syst�me �quip� d'un commutateur marche-arr�t, mettre l'appareil � l'arr�t (OFF) et d�brancher le cordon d'alimentation.
Warnung	Bevor Sie an einem System mit Ein/Aus-Schalter arbeiten, schalten Sie das System AUS und ziehen das Netzkabel aus der Steckdose.
Avvertenza	Prima di lavorare su un sistema dotato di un interruttore on/off, spegnere (OFF) il sistema e staccare il cavo dell'alimentazione.
Advarsel	Sl� AV str�mmen og trekk ut str�mledningen f�r det utf�res arbeid p� et system som er utstyrt med en av/p�-bryter.
Aviso	Antes de come�ar a trabalhar num sistema que tem um interruptor on/off, DESLIGUE a corrente el�ctrica e retire o cabo de alimenta��o da tomada.
�Advertencia!	Antes de utilizar cualquier sistema equipado con interruptor de Encendido/Apagado (ON/OFF), cortar la alimentaci�n y desenchufar el cable de alimentaci�n.
Varning!	Sl� AV str�mmen och dra ur n�tsladden innan du utf�r arbete p� ett system med str�mbrytare.

Power Supply Warning


Warning Do not touch the power supply when the power cord is connected. For systems with a power switch, line voltages are present within the power supply even when the power switch is off and the power cord is connected. For systems without a power switch, line voltages are present within the power supply when the power cord is connected.
Waarschuwing	U dient de voeding niet aan te raken zolang het netsnoer aangesloten is. Bij systemen met een stroomschakelaar zijn er lijnspanningen aanwezig in de voeding, zelfs wanneer de stroomschakelaar uitgeschakeld is en het netsnoer aangesloten is. Bij systemen zonder een stroomschakelaar zijn er lijnspanningen aanwezig in de voeding wanneer het netsnoer aangesloten is.
Varoitus	�l� kosketa virtal�hdett� virtajohdon ollessa kytkettyn�. Virrankatkaisimella varustetuissa j�rjestelmiss� on virtal�hteen sis�ll� j�ljell� verkkoj�nnite, vaikka virrankatkaisin on katkaistu-asennossa virtajohdon ollessa kytkettyn�. J�rjestelmiss�, joissa ei ole virrankatkaisinta, on virtal�hteen sis�ll� verkkoj�nnite, kun virtajohto on kytkettyn�.
Attention	Ne pas toucher le bloc d'alimentation quand le cordon d'alimentation est branch�. Avec les syst�mes munis d'un commutateur marche-arr�t, des tensions de ligne sont pr�sentes dans l'alimentation quand le cordon est branch�, m�me si le commutateur est � l'arr�t. Avec les syst�mes sans commutateur marche-arr�t, l'alimentation est sous tension quand le cordon d'alimentation est branch�.
Warnung	Ber�hren Sie das Netzger�t nicht, wenn das Netzkabel angeschlossen ist. Bei Systemen mit Netzschalter liegen Leitungsspannungen im Netzger�t vor, wenn das Netzkabel angeschlossen ist, auch wenn das System ausgeschaltet ist. Bei Systemen ohne Netzschalter liegen Leitungsspannungen im Netzger�t vor, wenn das Netzkabel angeschlossen ist.
Avvertenza	Non toccare l'alimentatore se il cavo dell'alimentazione � collegato. Per i sistemi con un interruttore di alimentazione, tensioni di linea sono presenti all'interno dell'alimentatore anche quando l'interruttore di alimentazione � en posizione di disattivazione (off), se il cavo dell'alimentazione � collegato. Per i sistemi senza un interruttore, tensioni di linea sono presenti all'interno dell'alimentatore quando il cavo di alimentazione � collegato.
Advarsel	Ber�r ikke str�mforsyningsenheten n�r str�mledningen er tilkoblet. I systemer som har en str�mbryter, er det spenning i str�mforsyningsenheten selv om str�mbryteren er sl�tt av og str�mledningen er tilkoblet. N�r det gjelder systemer uten en str�mbryter, er det spenning i str�mforsyningsenheten n�r str�mledingen er tilkoblet.
Aviso	N�o toque na unidade abastecedora de energia quando o cabo de alimenta��o estiver ligado. Em sistemas com interruptor, a corrente el�ctrica estar� presente na unidade abastecedora, sempre que o cabo de alimenta��o de energia estiver ligado, mesmo quando o interruptor se encontrar desligado. Para sistemas sem interruptor, a tens�o el�ctrica dentro da unidade abastecedora s� estar� presente quando o cabo de alimenta��o estiver ligado.
�Advertencia!	No tocar la fuente de alimentaci�n mientras el cable est� enchufado. En sistemas con interruptor de alimentaci�n, hay voltajes de l�nea dentro de la fuente, incluso cuando el interruptor est� en Apagado (OFF) y el cable de alimentaci�n enchufado. En sistemas sin interruptor de alimentaci�n, hay voltajes de l�nea en la fuente cuando el cable est� enchufado.
Varning!	Vidr�r inte str�mf�rs�rjningsenheten n�r n�tsladden �r ansluten. F�r system med str�mbrytare finns det n�tsp�nning i str�mf�rs�rjningsenheten �ven n�r str�mmen har slagits av men n�tsladden �r ansluten. F�r system utan str�mbrytare finns det n�tsp�nning i str�mf�rs�rjningsenheten n�r n�tsladden �r ansluten.

Further Information

Access to technical assistance as well as more information related to this product can be found at the following URL:

http://cisco.com

Table Of Contents