Configuring Cisco G.SHDSL HWICs in Cisco Access Routers

Table Of Contents

Configuring Cisco G.SHDSL HWICs in Cisco Access Routers

Contents

Prerequisites for Cisco G.SHDSL HWICs

Information About Cisco G.SHDSL HWICs

Cisco G.SHDSL HWICs

Connecting Cisco G.SHDSL HWICs to the Network

Configuring Cisco G.SHDSL HWICs

Configuring IMA Groups

Configuring M-Pair Groups

Configuring 1-Pair Groups and 2-Pair Groups

Troubleshooting Cisco G.SHDSL HWICs

Command Reference

controller shdsl

dsl-group

ima-group

ima group clock-mode

ima link

shdsl 4-wire mode

shdsl annex

shdsl rate

show controllers shdsl

Additional References

Related Documents

Standards

MIBs

RFCs

Technical Assistance

Configuring Cisco G.SHDSL HWICs in Cisco Access Routers

First Published: December 23, 2006 OL-11079-01

Last Updated: December 15, 2006

This document describes how to configure Cisco G.SHDSL high-speed WAN interface cards (HWICs). Cisco G.SHDSL HWICs connect Cisco access routers with central office digital subscriber line access multiplexer (DSLAMs) and provide as many as four lines of G.SHDSL (ITU-T 991.2) connectivity.

Finding Support Information for Platforms and Cisco IOS Software Images

Use Cisco Feature Navigator to find information about platform support and Cisco IOS software image support. Access Cisco Feature Navigator at http://www.cisco.com/go/fn. You must have an account on Cisco.com. If you do not have an account or have forgotten your username or password, click Cancel at the login dialog box and follow the instructions that appear.

Contents

• Prerequisites for Cisco G.SHDSL HWICs

• Information About Cisco G.SHDSL HWICs

• Connecting Cisco G.SHDSL HWICs to the Network

• Configuring Cisco G.SHDSL HWICs

• Troubleshooting Cisco G.SHDSL HWICs

• Command Reference

• Additional References

Prerequisites for Cisco G.SHDSL HWICs

•Ensure that you have the appropriate Cisco access router to serve as the host router.
The following Cisco access routers support Cisco G.SHDSL HWICs.

–Cisco 1841

–Cisco 2800 series

–Cisco 3800 series

•Use the show version command to ensure that the router is running Cisco IOS Release12.4(11) XJ or a later release.

Note When minimum release requirements are met, you can change images on the router without affecting performance.

•Install the Cisco G.SHDSL HWIC on the router, using the directions provided in the Cisco Interface Cards Hardware Installation Guide and Cisco Network Modules and Interface Cards Regulatory Compliance and Safety Information.

Information About Cisco G.SHDSL HWICs

Cisco G.SHDSL HWICs support up to four pairs of digital subscriber lines (DSL): two inverse multiplexing over ATM (IMA) lines, and two ATM segmentation and reassembly (SAR) lines. The four DSL pairs are bundled in groups and configured in the Cisco IOS command-line interface (CLI) by using the dsl-group command.

G.SHDSL HWICs support the following DSL groups:

•Inverse Multiplexing over ATM (IMA) groups—1- 4 DSL pairs

•Multi-Pair Operation (M-Pair) groups—2 or more DSL pairs

•2-Pair groups—2 DSL pairs

•1-Pair groups—1 DSL pair

See the "Command Reference" section for more information about commands used with Cisco G.SHDSL HWICs.

Cisco G.SHDSL HWICs

Cisco G.SHDSL HWICs are available in two variations:

•The Cisco HWIC-2SHDSL ( Figure 1) provides two lines of connectivity through one RJ-11 connector. It supports 1-Pair groups or 2-Pair groups.

Figure 1

Cisco HWIC-2SHDSL Faceplate

•The Cisco HWIC-4SHDSL ( Figure 2) provides four lines of connectivity through one RJ-45 connector. It combines four lines of data into one line or two lines with either inverse multiplexing over ATM (IMA) groups or M-pair groups, and it supports 1-Pair groups or 2-Pair groups.

Figure 2

Cisco HWIC-4SHDSL Faceplate

Note The Cisco HWIC-2SHDSL provides support for the Dying Gasp feature; however, the Cisco HWIC-4SHDSL does not provide support for this feature. The term dying gasp refers to power status as defined in ITU-T standard G.991.2, section 7.1.2.5.3.

EN

Status of the system:

Green—Operating system is running.

Amber—Interface card is resetting.

Blinking—System is initializing.

L0, L1, L2, L3

Status of link:

On—Link is active.

Off—Link is inactive (disabled).

Blinking— Link is training / Link alarm

What to do next

See the "Connecting Cisco G.SHDSL HWICs to the Network" section for cable information.

Connecting Cisco G.SHDSL HWICs to the Network

Connect Cisco G.SHDSL HWICs as described next:

•Cisco HWIC-2SHDSL—Use a standard RJ-11 straight-through cable to establish connection between the HWIC and a network device.

•Cisco HWIC-4SHDSL—Use a standard RJ-45 straight-through cable to establish connection between the HWIC and a network device.

Figure 3 shows the RJ-45 pin assignment. Table 1 identifies the RJ-45 signal assignment by pin.

Caution Inserting an RJ-11 connector into the Cisco HWIC-4SHDSL port may deform pins 1 and 8, which may prevent solid contact between the connector and the plug in subsequent connections. If solid contact is prevented, line -1 tip and line -3 ring will not work properly.

Figure 3

RJ-45 Pin Assignment

Table 1 RJ-45 Signal Assignment by Pin

Pin

Signal

1

Line 1 tip

2

Line 1 ring

3

Line 2 tip

4

Line 0 tip

5

Line 0 ring

6

Line 2 ring

7

Line 3 tip

8

Line 3 ring

To connect the Cisco HWIC-4SHDSLwith a DSLAM that supports two or four RJ-11 connections, modify the standard RJ-45 cable, using one of the following diagrams as applicable:

• Figure 4 shows how to modify the cable and connect the Cisco HWIC-4SHDSL with a DSLAM that supports four RJ-11 cable connections.

• Figure 5 shows how to modify the cable and connect the Cisco HWIC-4SHDSL with a DSLAM that supports two RJ-11 cable connections.

Figure 4 Standard RJ-45 Connector to Four Standard RJ-11 Connectors

Figure 5 Standard RJ-45 Connector to Two Standard RJ-11 Connectors

What to Do Next

See the "Configuring Cisco G.SHDSL HWICs" section for information about configuring DSL groups.

Configuring Cisco G.SHDSL HWICs

Configure DSL groups on the Cisco G.SHDSL HWIC, using the Cisco IOS CLI on the router in privileged configuration mode.

• Configuring IMA Groups

• Configuring M-Pair Groups

• Configuring 1-Pair Groups and 2-Pair Groups

Configuring IMA Groups

Use the Cisco IOS CLI on the router in global configuration mode to configure an IMA group on the Cisco HWIC-4SHDSL.

SUMMARY STEPS

1. controller shdsl

2. dsl-group

3. ima link add

4. ima group minimum-links

5. ima group clock-mode

6. shdsl annex

7. shdsl rate

8. exit

9. exit

Command

Purpose

Step 1

controller shdsl slot number/subslot number/0 Example: Router (config)# controller shdsl 0/2/0
Router (config-controller)#

Selects the controller and enters config-controller mode.

See the "controller shdsl" section for more information.

Step 2

dsl-group number pairs link number [ima | m-pair]

Example:
Router (config-controller)# dsl-group 0 pairs 0-3 ima

Creates a DSL group and enters config-controller-dsl-group mode.

See the "dsl-group" section on page 25 for more information.

Step 3

ima link {add | delete | shutdown}number

Example:
Router (config-controller-dsl-group)# ima link add 2

Modifies links in an IMA group.

See the "ima link" section on page 33 for more information.

Step 4

ima group {shutdown|minimum-links number | clock-mode}

Example:
Router (config-controller-dsl-group)# ima group minimum-links 2

Modifies IMA group behavior.

See the "ima-group" section for more information.

Step 5

ima group clock-mode {ctc | itc}

Example:
Router (config-controller-dsl-group)# ima group clock-mode ctc

Defines the clock mode for an IMA group.

See the "ima group clock-mode" section for more information.

Step 6

shdsl annex {standard}

Example:
Router (config-controller-dsl-group)# shdsl annex A

Defines the SHDSL annex.

See the "shdsl annex" section on page 36 for more information.

Step 7

shdsl rate {number | auto}

Example:
Router (config-controller-dsl-group)# shdsl rate auto

Defines the SHDSL rate.

See the "shdsl rate" section on page 38 for more information.

Step 8

exit

Example:
Router (config-controller-dsl-group)# exit

Exits config-controller-dsl-group mode.

Step 9

exit

Example:
Router (config-controller)# exit

Exits config-controller mode.

DETAILED STEPS

Examples

The following example use the G.SHDSL commands to configure an IMA group on a HWIC- 4SHDSL.

Router(config)# controller shdsl 0/2/0
Router(config-controller)# dsl-group 1 pairs 1 ima
Router(config-controller-dsl-group)#?
dsl-group configuration sub commands:
default Set a command to its defaults
exit Exit dsl-group sub commands
ima IMA sub commands
no Negate a command or set its defaults
shdsl Symmetric g.shdsl configuration
shutdown Shutdown this dsl-group
Router(config-controller-dsl-group)# ima link add 2
Router(config-controller-dsl-group)# ima group minimum-links 2
Router(config-controller-dsl-group)# ima group clock-mode ?
ctc Common Transmit Clock configuration
itc Independent Transmit Clock configuration
Router(config-controller-dsl-group)# ima group clock-mode ctc ?
Router(config-controller-dsl-group)# shdsl annex a
Router(config-controller-dsl-group)# shdsl rate auto
Router(config-controller-dsl-group)# exit
Router(config-controller)# exit
Configuring M-Pair Groups

Use the Cisco IOS CLI on the router in global configuration mode to configure an M-Pair group on the Cisco HWIC-4SHDSL.

Note To ensure a successful M-Pair group configuration, confirm that the central office (CO) network equipment that is connected with the Cisco HWIC-4SHDSL supports M-Pair bonding.

SUMMARY STEPS

1. controller shdsl

2. dsl-group

3. shdsl annex

4. shdsl rate

5. exit

6. exit

DET

Command

Purpose

Step 1

controller shdsl slot number/subslot number/0 Example: Router (config)# controller shdsl 0/2/0
Router (config-controller)#

Selects the controller and enters config-controller mode.

See the "controller shdsl" section for more information.

Step 2

dsl-group number pairs link number [ima | m-pair]

Example:
Router (config-controller)# dsl-group 0 pairs 0-1 m-pair

Creates a DSL group and enters config-controller-dsl-group mode.

See the "dsl-group" section on page 25 for more information.

Step 3

shdsl annex {standard}

Example:
Router (config-controller-dsl-group)# shdsl annex A-B

Defines the SHDSL annex.

See the "shdsl annex" section on page 36 for more information.

Step 4

shdsl rate {number | auto}

Example:
Router (config-controller)# shdsl rate 2048

Defines the SHDSL rate.

See the "shdsl rate" section on page 38 for more information.

Step 5

exit

Example:
Router (config-controller-dsl-group)# exit

Exits config-controller-dsl-group mode.

Step 6

exit

Example:
Router (config-controller)# exit

Exits config-controller mode.

AILED STEPS

Examples

The following example use the G.SHDSL commands to configure an M-Pair group on a HWIC-4SHDSL.

Router(config)#
Router(config)# controller shdsl 0/2/0
Router(config-controller)# dsl-group 1 pairs 0-1 m-pair
Router(config-controller-dsl-group)#
Sep 27 14:16:00.167: %HWIC_SHDSL-5-DSLGROUP_UPDOWN: SHDSL 0/2/0 dsl-group(1) state changed to down.
Sep 27 14:16:02.167: %LINK-3-UPDOWN: Interface ATM0/2/1, changed state to down
Sep 27 14:16:03.167: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0/2/1, changed state to down
Router(config-controller-dsl-group)# shdsl annex a-b
Router(config-controller-dsl-group)# shdsl rate 2048
Router(config-controller-dsl-group)# exit
Router(config-controller)# exit
Router(config)#
Configuring 1-Pair Groups and 2-Pair Groups

To configure a 1-Pair group or 2-Pair group on a Cisco HWIC-4SHDSL or HWIC-2SHDSL, use the Cisco IOS CLI on the router in global configuration mode.

SUMMARY STEPS

1. controller shdsl

2. dsl-group

3. shdsl 4-wire mode
(For 2-Pair groups only)

4. shdsl annex

5. shdsl rate

6. exit

7. exit

DET

Command

Purpose

Step 1

controller shdsl slot number/subslot number/0 Example: Router (config)# controller shdsl 0/2/0
Router (config-controller)#

Selects the controller and enters config-controller mode.

See the "controller shdsl" section for more information.

Step 2

dsl-group number pairs link number

Example(1-pair group):
Router (config-controller)# dsl-group 0 pairs 0

Example(2-pair group):
Router (config-controller)# dsl-group 0 pairs 0-1

Creates a DSL group and enters config-controller-dsl-group mode.

See the "dsl-group" section on page 25 for more information.

Step 3

shdsl 4-wire mode enhanced

Example:
Router (config-controller)# shdsl 4-wire mode enhanced

Defines a 2-pair group as enhanced.

See the "shdsl 4-wire mode" section for more information.

Step 4

shdsl annex {standard}

Example:
Router (config-controller-dsl-group)# shdsl annex A-B

Defines the SHDSL annex.

See the "shdsl annex" section on page 36 for more information.

Step 5

shdsl rate {number|auto}

Example:
Router (config-controller)# shdsl rate 2048

Defines the SHDSL rate.

See the "shdsl rate" section on page 38 for more information.

Step 6

exit

Example:
Router (config-controller-dsl-group)# exit

Exits config-controller-dsl-group mode.

Step 7

exit

Example:
Router (config-controller)# exit

Exits config-controller mode.

AILED STEPS

Examples

The following example use the G.SHDSL commands to configure a 1-Pair group and 2-Pair group on a HWIC-4SHDSL and HWIC-2SHDSL.

1-Pair Group Configuration

Router(config)# controller shdsl 0/2/0
Router(config-controller)# dsl-group 0 pairs 0
Router(config-controller-dsl-group)#
Oct 4 14:30:48.863: %HWIC_SHDSL-5-DSLGROUP_UPDOWN: SHDSL 0/2/0 dsl-group(0) state changed to down.
Oct 4 14:30:50.863: %LINK-3-UPDOWN: Interface ATM0/2/0, changed state to down
Oct 4 14:30:51.863: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0/2/0, changed state to down
Router(config-controller-dsl-group)# shdsl annex ?
A Annex A of G.991.2 standard
A-B Annex A/B of G.991.2 standard
B Annex B of G.991.2 standard
F Annex F of G.991.2 standard
F-G Annex F/G of G.991.2 standard
G Annex G of G.991.2 standard
Router(config-controller-dsl-group)# shdsl annex A-B
Router(config-controller-dsl-group)# shdsl rate ?
<192-2304> DSL Rate in kbps(line will train at the rate + 16kbps overhead)
auto auto rate mode
Router(config-controller-dsl-group)# shdsl rate 2048
Router(config-controller-dsl-group)# exit
Router(config-controller)# exit
Router(config)#
2-Pair Group Configuration

Router(config)# controller shdsl 0/2/0
Router(config-controller)# dsl-group 0 pairs 0-1
Router(config-controller-dsl-group)#
Oct 4 14:37:01.027: %HWIC_SHDSL-5-DSLGROUP_UPDOWN: SHDSL 0/2/0 dsl-group(0) state changed to down.
Oct 4 14:37:03.027: %LINK-3-UPDOWN: Interface ATM0/2/0, changed state to down
Oct 4 14:37:04.027: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0/2/0, changed state to down
Router(config-controller-dsl-group)# shdsl ?
4-wire Symmetric g.shdsl 4-wire mode configuration
annex Symmetric g.shdsl Annex configuration
rate DSL line rate configuration
Router(config-controller-dsl-group)# shdsl 4-wire mode ?
enhanced 4-wire mode start up on both pairs
Router(config-controller-dsl-group)# shdsl 4-wire mode enhanced
Router(config-controller-dsl-group)# shdsl ?
4-wire Symmetric g.shdsl 4-wire mode configuration
annex Symmetric g.shdsl Annex configuration
rate DSL line rate configuration
Router(config-controller-dsl-group)# shdsl annex ?
A Annex A of G.991.2 standard
A-B Annex A/B of G.991.2 standard
B Annex B of G.991.2 standard
F Annex F of G.991.2 standard
F-G Annex F/G of G.991.2 standard
G Annex G of G.991.2 standard
Router(config-controller-dsl-group)# shdsl annex A-B
Router (config-controller-dsl-group)# shdsl rate ?
<384-4608> DSL Rate in kbps(line will train at the rate + 16kbps overhead)
auto auto rate mode
Router(config-controller-dsl-group)# shdsl rate 2048
Router(config-controller-dsl-group)# exit
Router(config-controller)# exit

Troubleshooting Cisco G.SHDSL HWICs

To troubleshoot Cisco G.SHDSL HWICs, use the following new and published Cisco IOS commands. All other Cisco IOS software commands used with G.SHDSL HWICs are documented in the Cisco IOS Release 12.4(11) XJ command reference publication at Cisco.com:

http://www.cisco.com/en/US/products/ps6441/tsd_products_support_series_home.html

SUMMARY STEPS

1. show controllers shdsl
(new command)

2. show controllers atm

3. show ima interface

4. show ima interface atm

5. show atm pvc

DET

Command

Purpose

Step 1

show controllers shdsl slot number/subslot number/0 [detailed | brief] Example: Router# show controllers shdsl 0/2/0 detailed

Displays the status of SHDSL controllers.

See the "show controllers shdsl" section on page 40 for more information.

Step 2

show controllers atm [slot/subslot number/imagroup-number]

Example: Router# show controllers atm 0/1/ima0

Displays information about the IMA group.

Step 3

show ima interface

Example: Router# show ima interface

Displays information about the IMA interface.

Step 4

show ima interface atm [slot/subslot number/imagroup-number] [detailed]

Example: Router# show ima interface atm 0/1/ima0

Displays detailed information about the IMA interface.

Step 5

show atm pvc
Example: Router# show atm pvc

Displays information about ATM permanent virtual connections (PVCs) and traffic information.

AILED STEPS

Examples

The following example uses the show controllers shdsl command to display the controller status on a HWIC-4SHDSL.

show controllers shdsl

Router# show controllers shdsl 0/2/0 detailed
Controller SHDSL 0/2/0 is UP
Hardware is HWIC-4SHDSL, rev 2 on slot 0, hwic slot 2
Capabilities: IMA, M-pair, 2/4 wire, Annex A, B, F & G, CPE termination
cdb=0x43D8E90C, plugin=0x43CC44D0, ds=0x43D75284 base=0xB8000000
FPGA Version is REL.3.4.0, NIOSII FW:Ver 2.6, status Running
SDC-16i HW:Rev 1.2, status UP, FW:Ver 1.2-1.1.3__57, status Running
SDFE-4 HW:Rev 1.2, status UP, FW:Ver 1.1-1.5.2__001 , status Running
NIOSII Firmware image: System
SDC16i Firmware image: System
SDFE4 Firmware image: System
Number of pairs 4, number of groups configured 1
Ignored CLI cmds(0), Event buffer: in use(0), failed(0)
Group (0) info:
Type: 2-wire g.shdsl, status: Configure Firmware
Interface: ATM0/2/0, hwidb: 0x43D8EA54, UTOPIA phy 0
Configured/active num links: 1/0, bit map: 0x1/0x0
Line termination: CPE, line mode: 2-wire, Annex-B, PMMS disabled
Line coding: 16-TCPAM, configured/actual rate: 2304/0 kbps
SHDSL wire-pair (0) is in DSL DOWN state
Termination: CPE, line mode: 2-wire, Annex-B
Line coding: 16-TCPAM, configured/actual rate: 2304/0 kbps
CONNECT state: MAIN_PRE_ACT, cond: NONE, reason: ERR_NONE
Power back off: 0dB, FE power back off: 0dB
LoopAttn: 0dB, SnrMargin: 0dB, Status noDefect
Current 15 minute statistics (Time Elapsed 608 seconds):
ES: 0, SES: 0, CRC: 0, LOSWS: 0, UAS: 0
Previous 15 minute statistics:
ES: 0, SES: 0, CRC: 0, LOSWS: 0, UAS: 0
Current 24 hr statistics:
ES: 0, SES: 0, CRC: 0, LOSWS: 0, UAS: 0
Previous 24 hr statistics:
ES: 0, SES: 0, CRC: 0, LOSWS: 0, UAS: 0
ATM-TC Tx: data cells: 0, Idle/Unassigned: 0
ATM-TC Rx: data cells: 0, uncorr HEC: 0, corr HEC: 0
ATM-TC Rx: OCD: 0, LCD start: 0, LCD end: 0
Group (1) is Not configured.
***** Firmware Status Information Start *****

ticks: 537140002, heapmem used: 223744 bytes

Utopia information:
ints: 1, last intr status: 0x00000000
utopia_tx_stuck_count: 1, utopia_rx_stuck_count: 1
sar0_rcv_parity_errs: 0, sar0_rcv_errs: 0
sar1_rcv_parity_errs: 0, sar1_rcv_errs: 0

IPC information:
tx_polling: false
Tx ok 538289, poll 0, fails qfull 0, noinit 0, dma 0
Rx ok 53867, fails nobufs 0, noapp 0

DMA information:
Write req 538294, complete 538294, underruns 0, overruns 0

VOS:
write fail1: 0, fail2: 0, fail3: 0

App Group information:
grp 0, tsnid 9, linkmap 0x1, flags 0x00, imacmd 0, realMWMaster 0
grp 1, tsnid 0, linkmap 0x0, flags 0x00, imacmd 0, realMWMaster 0

App information:
ch 0, pre_st 6, cur_st 6, tr 2, flags 0x210
ch 1, pre_st 8, cur_st 8, tr 3, flags 0x000
ch 2, pre_st 1, cur_st 5, tr 3, flags 0x000
ch 3, pre_st 1, cur_st 5, tr 3, flags 0x000

Chip information:
ch 0, state 1, cond 0, reason 0, prims 0xff, fbits 0x0f, vendFe 0
sa 1 crca 1 sd 1 loswd 1 snrmd 1 lad 1 loswf 1 trr 1 pwr status 1
ch 1, state 0, cond 0, reason 0, prims 0xff, fbits 0x0f, vendFe 0
sa 1 crca 1 sd 1 loswd 1 snrmd 1 lad 1 loswf 1 trr 1 pwr status 1
ch 2, state 0, cond 0, reason 0, prims 0xff, fbits 0x0f, vendFe 0
sa 1 crca 1 sd 1 loswd 1 snrmd 1 lad 1 loswf 1 trr 1 pwr status 1
ch 3, state 0, cond 0, reason 0, prims 0xff, fbits 0x0f, vendFe 0
sa 1 crca 1 sd 1 loswd 1 snrmd 1 lad 1 loswf 1 trr 1 pwr status 1

Global information:
DSL wait 0, flags 0x7, cctmsgs 0, ipcmsgs 0
DSL rate mismatch 0, cct write fails 0, ipc write fails 0
DSL cmds sent: line_cfg 9, start_data 9
stop_data 8, rel_conn 8
IMA cmds sent: addgrp 0, delgrp 0, addlink 0
dellink 0, set_param 0
IMA fails addgrp 0, delgrp 0, addlink 0 dellink 0
/pipe/dsl_ipc_norm, mqp 0x3f66f0, nmsgs 32, msgsize 4
magic 0xbeefbacc, p_start 0x3f6720, p_end 0x3f68a0, memsize 384
free mhead 0x3f6780 mtail 0x3f6774 numfree 32
read qhead 0x0 qtail 0x0 qcount 0

CC information:
global state 4, restart 0, AppWrite fails 0
fatalError 0, selectErr 0
rxEctEvtNoMsgs 0, rxMctEvtNoMsgs 0, rxAppEvtNo Msgs 0
dciMsg2MctFails 0, ctrlMsg2MctFails 0, ectSendFails 0
sciMsg2MctFails 0, sciAuxMsg2MctFails 0, sciRsMsg2MctFails 0

Channel cfg:
ch 0, state 5, substate 12, conntype 1, mwire 0, realMwMaster 0
ch 1, state 4, substate 0, conntype 1, mwire 1, realMwMaster 0
ch 2, state 4, substate 0, conntype 1, mwire 0, realMwMaster 0
ch 3, state 4, substate 0, conntype 1, mwire 0, realMwMaster 0

Channel var:
ch 0, state 5, atmsync 0, atmtcenable 0, delayMt 0, delay 0
ch 1, state 1, atmsync 0, atmtcenable 0, delayMt 0, delay 0
ch 2, state 1, atmsync 0, atmtcenable 0, delayMt 0, delay 0
ch 3, state 1, atmsync 0, atmtcenable 0, delayMt 0, delay 0

IMA group info:
idx 0, state 0, rate 0, id 0, GrpId 255, mod 0, mismatch 0
idx 1, state 0, rate 0, id 0, GrpId 255, mod 0, mismatch 0
idx 2, state 0, rate 0, id 0, GrpId 255, mod 0, mismatch 0
idx 3, state 0, rate 0, id 0, GrpId 255, mod 0, mismatch 0

IMA link info:
idx 0, imaGrp 255, linkId 255, rate 0, mismatch 0
idx 1, imaGrp 255, linkId 255, rate 0, mismatch 0
idx 2, imaGrp 255, linkId 255, rate 0, mismatch 0
idx 3, imaGrp 255, linkId 255, rate 0, mismatch 0

MC information:
state 5, nDciInUse 0, fatalerr 0

DciInUse >= 10 msgs err:
dsDci 0, dsSci 0, dsSciAux 0, dsSciRs 0, rxCCT 0 rxEct 0

Other Stats:
dsDciWrFails1 0, dsDciWrFails2 0, dsSciAckLost 0
dsSciWrFails1 0, dsSciWrFails2 0, dsSciAuxWrFails1 0
dsSciAuxWrFails2 0, dsSciRsWrFails1 0, dsSciRsWrFails2 0
usSciInvalidLen 0, usSciUnexpectedAck 0, usSciMsgFw2EctFails 0
usSciMsgFw2CctFails 0, usSciAuxInvalidLen 0, usSciSendFails 0
usDciSendFails 0, sciBlocking 0, dciBlocking 0

EC information:
mctMsgsRx 0, mctMsgsTxFails 0, mctMsgsTxOks 0

VOS Pipes:
/pipe/CCT_FROM_APP_0, mqp 0x3c0c78, nmsgs 32, msgsize 400
magic 0xbeefbacc, p_start 0x3c0ca8, p_end 0x3c3fa8, memsize 13056
free mhead 0x3c3e10 mtail 0x3c3c78 numfree 32
read qhead 0x0 qtail 0x0 qcount 0

/pipe/CCT_TO_APP_0, mqp 0x3c4018, nmsgs 64, msgsize 400
magic 0xbeefbacc, p_start 0x3c4048, p_end 0x3ca648, memsize 26112
free mhead 0x3c6e80 mtail 0x3c6ce8 numfree 64
read qhead 0x0 qtail 0x0 qcount 0

/pipe/CCT_FROM_MCT_0, mqp 0x3ca6b8, nmsgs 96, msgsize 400
magic 0xbeefbacc, p_start 0x3ca6e8, p_end 0x3d3fe8, memsize 39168
free mhead 0x3cabb0 mtail 0x3caa18 numfree 96
read qhead 0x0 qtail 0x0 qcount 0

/pipe/CCT_FROM_ECT_0, mqp 0x3d4058, nmsgs 32, msgsize 400
magic 0xbeefbacc, p_start 0x3d4088, p_end 0x3d7388, memsize 13056
free mhead 0x3d4088 mtail 0x3d71f0 numfree 32
read qhead 0x0 qtail 0x0 qcount 0

/pipe/MCT_TO_ECT_0, mqp 0x3d73f8, nmsgs 64, msgsize 400
magic 0xbeefbacc, p_start 0x3d7428, p_end 0x3dda28, memsize 26112
free mhead 0x3d7428 mtail 0x3dd890 numfree 64
read qhead 0x0 qtail 0x0 qcount 0

/pipe/CCT_TO_ECT_0, mqp 0x3dda98, nmsgs 32, msgsize 400
magic 0xbeefbacc, p_start 0x3ddac8, p_end 0x3e0dc8, memsize 13056
free mhead 0x3e0a98 mtail 0x3e0900 numfree 32
read qhead 0x0 qtail 0x0 qcount 0

/pipe/CCT_TO_MCT_0, mqp 0x3e36e8, nmsgs 96, msgsize 400
magic 0xbeefbacc, p_start 0x3e3718, p_end 0x3ed018, memsize 39168
free mhead 0x3ead08 mtail 0x3eab70 numfree 96
read qhead 0x0 qtail 0x0 qcount 0

/pipe/MCT_FROM_ECT_0, mqp 0x3ed088, nmsgs 64, msgsize 400
magic 0xbeefbacc, p_start 0x3ed0b8, p_end 0x3f36b8, memsize 26112
free mhead 0x3ed0b8 mtail 0x3f3520 numfree 64
read qhead 0x0 qtail 0x0 qcount 0

Tasks:
tIPC delay 00000 flags 0x002 schedcnt 106899104
tMCT_0 delay 00000 flags 0x000 schedcnt 21379921
tCCT delay 00011 flags 0x000 schedcnt 10743684
sCCT delay 00236 flags 0x000 schedcnt 537184
tECT delay 00460 flags 0x000 schedcnt 537195
tDMT delay 00010 flags 0x000 schedcnt 11280188

***** Firmware Status Information End *****

IPC Info: host_base=0xF59B040, sram_base=0xB81E0000
CmdType Tx TxErr Rx RxFailed RxUnknown
GEN 6 0 8 0 0
DBG 0 0 0 0 0
DSL 34 0 536537 0 0
IMA 0 0 0 0 0
EOC 0 0 0 0 0
******* HWIC Common Registers at B8000000 *******
HWIC ID: 0x1
HWIC Revision: 0x4
HWIC Status: 0x0
HWIC DDR TXCRC:0x0
HWIC Control: 0x8040
DDR Enable 1 Software Reset 0
Interrupt Module Reset 0 GDF Module Reset 0
DMA Module Reset 0 Flow Control Reset 0
IRQ2 Global Int Mask 0 IRQ1 Global Int Mask 1
DDR TXCRC Int Mask 0 DDR TXClk Loss Int Mask 0
TX Fifo Overrun Int Mask 0
HWIC Interrupt Event: 0x0
DDR TXCRC Int 0 DDR TXClk Loss Int 0
TX Fifo Overrun Int 0
HWIC Diag 1: 0x0
HWIC Diag 2: 0x1E0F

******* HWIC Host Registers at B8A00000 *******
Status (0x00):
Card Present Low 0 Graceful Stop Tx Complete 0
Config (0x00000806):
Hwic Reset 0 Hwic Host Reset 0
Hwic IRQ2 Type Err Hwic IRQ1 Type Net
Rx Queue Watermark Enable 0 Auto XOFF When Full 0
Rx Int On Last 0 Graceful Stop Tx 0
Generic Rx Enable 0 Generic Tx Enable 1
DDR Enable 1 Loopback 0
Error Interrupt Enable (0x37EFF):
Rx Done Error Int 1 Card Present Change Int 1
Hwic Int Frame Error Int 0x07 Tx First Last Error Int 1
Tx Done Error Int 1 IRQ2 Int 1
IRQ1 Int 0 Host Specific Error Int 1
Rx Overrun Int 1 DDR RxClk Missing Int 1
Reg RW Timeout Int 1 Reg RW Error Int 1
Rx CRC Int 1 Rx Format Error Int 1
DMA Error Int 1
Management Interrupt Enable (0xA000):
Hwic Int Frame Mgmt Int 0x0A
IRQ2 Int 0
IRQ1 Int 0 Graceful Stop Tx Int 0
Network Interrupt Enable (0x003F):
Rx Frame Drop Int 0 Generic Frame Tx Int 0
Generic Frame Rx Int 0 DMA Write Int 0
IRQ2 Int 0 IRQ1 Int 0
Int Frame Network Int 0x3F
Error Interrupt Event (0x0000):
Rx Done Error Event 0 Card Present Change Event 0
Hwic Int Frame Error Event 0x00 Tx First Last Error Event 0
Tx Done Error Event 0 IRQ2 Event 0
IRQ1 Event 0 Host Specific Error Event 0
Rx Overrun Event 0 DDR RxClk Missing Event 0
Reg RW Timeout Event 0 Reg RW Error Event 0
Rx CRC Event 0 Rx Format Error Event 0
DMA Error Event 0
Management Interrupt Event (0x0000):
Hwic Int Frame Mgmt Event 0x00
IRQ2 Int 0
IRQ1 Int 0 Graceful Stop Tx Event 0
Network Interrupt Event (0x1000):
Rx Frame Drop Event 0 Generic Frame Tx Event 1
Generic Frame Rx Event 0 DMA Write Event 0
IRQ2 Event 0 IRQ1 Event 0
Int Frame Network Event 0x00
HWICRegisterOffset 0x0000 HWICRegisterErrorAddress 0x00000000
HWICRegisterTimeout 0x0000C350
TxControlFrameCounter 0x2B4F3F RxControlFrameCounter 0x264A19
TxDataFrameCounter 0x00D271 RxDataFrameCounter 0x0836E6
RegisterRWErrorCounter 0x0000 RxOverrunErrorCounter 0x0000
RxCRCErrorCounter 0x0000 RxFrameDropCounter 0x0000
TxBufferExtension 0x00 RxBufferExtension 0x00
HWICQueueBaseExtension 0x00 HWICQueueBase 0x0F59
TXQueueTailBase Register 0xC088
TxQueueBase 0x18 TxQueueTail 0x11
TxQueueSize 0x20 TxQueueHead 0x11
RxQueueHeadBase Register 0x0000
RxQueueBase 0x00 RxQueueHead 0x00
RxQueueSize 0x00 RxQueueTail 0x00
RxBufferSize 0x0000 RxQueueHighWaterMark 0x00
RxQueueLowWaterMark 0x00 DMAOffsetExtension 0x00
DMAOffset 0x0000 DMAWindow 0x0000

The following example uses the show controllers atmcommand to display information about an IMA group.

show controllers atm

Router#show controllers atm 0/1/ima0
DSL SAR Info
Interface: ATM0/1/IMA0 Hardware: DSLSAR WITH IMA State: up
IDB: 0x4358A1F8 Instance: 0x435B70C8 dpi: 0x435D3C90
PHY bw: 4608 kbps Cell tick: 0x00121ECA Current TST: 1
NetIO enable: 0x003F Int status: 0x0000, sram_base(h): 0xB0240000
SAR reg base: 0xB0202400 Host reg base: 0xB0A00400
SAR config: 0x200D0A20 SAR status: 0x00000000
RPQ head: 0x0F394330 RPQ tail:0x0F394330
RCQ head: 0x0F390D40 RCQ tail:0x0F390D40
FBQ head: 0x000198DC FBQ tail:0x00019CBC
TBQ head: 0x0F392260 TBQ tail:0x0F392260
RCT base: 0x0001A000 RCID base:0x00030000
Tx ints: 0x00005842 Rx pkt ints: 0x00005495
Rx cell ints: 0x000003E9 Rx pkts: 0x00005118
Tx pkts: 0x00005119 Tx OAM cells: 0x000003C0
Rx raw cells: 0x000003C0
Utopia Tx cells: 0x0009D5C2 Utopia Rx cells: 0x0009D5C2
Utopia Tx rate: 10742.43 cps, 4554790 bps
Tx idle rate: 0.00 cps, 0 bps
Utopia Rx rate: 10742.43 cps, 4554790 bps
Bad tbd_ids: 0x00000000, Tx error: 0x00000000
oam_nobuf: 0x00000000 no_tbd_id: 0x00000000 shaping_defer: 0x00000000
bad_oam_rx: 0x00000000 delayed_rpqe: 0x00000000 delayed_tbqe: 0x00000000
DSL SAR Info
Unknown vpi/vci: 0x00000000, Inv cells: 0x00000000
TCD[0]: 0x00000000 TCD[1]: 0x00000040
TST[0]: 0x00000240 TST[1]: 0x0000CB6C
Boot jump: 0x00019498 RCTE[0]: 0x0001A000 FBQ: 0x00019800
lp_tcq[0][0]: 0x0001B000 lp_tcq[0][1]: 0x0001B010
lp_tcq[1][0]: 0x0001C000 lp_tcq[1][1]: 0x0001C010
hp_tcq[0][0]: 0x00024000 hp_tcq[0][1]: 0x00024010
hp_tcq[1][0]: 0x00025000 hp_tcq[1][1]: 0x00025010
rx_conn_id[0]: 0x00030000 rcte[0]: 0x0001A000
Configured vcs:
VCD VPI VCI QoS(c) QoS(a) BW(c) BW(a) RCTE rd(min/max/var)
1 1 11 5 5 0 4608 0x000A220B 3370/22859/19489
2 1 12 5 5 0 4608 0x000A221C 4035/23100/19064
3 1 13 5 5 0 4608 0x000A2211 3197/22446/19248
4 1 14 5 5 0 4608 0x000A2203 3607/21524/17917
5 1 15 5 5 0 4608 0x000A0000 4022/29498/25476
6 1 16 5 5 0 4608 0x000A2209 20/12401/12381
7 1 17 5 5 0 4608 0x000A0000 --
8 1 18 5 5 0 4608 0x000A0000 5651/19762/14110
VC Tx stats:
VCD Tx(hp) Tx(lp) ring(p/b) pkts(h/l) bufs(h/l) td(min/max/var)
0 0x00000440 0x00000000 30/30 0/0 0/0 7176/7916/739
1 0x00000B81 0x00000000 30/30 30/0 30/0 15160/15402/241
DSL SAR Info
2 0x00000B81 0x00000000 30/30 30/0 30/0 15160/15402/241
3 0x00000B9E 0x00000000 30/30 30/0 30/0 15160/15415/255
4 0x00000B9E 0x00000000 30/30 30/0 30/0 15160/15415/255
5 0x00000B9F 0x00000000 30/30 30/0 30/0 15160/15402/241
6 0x00000B9E 0x00000000 30/30 30/0 30/0 15160/15456/295
7 0x00000B9E 0x00000000 30/30 30/0 30/0 15160/15469/309
8 0x00000B9E 0x00000000 30/30 30/0 30/0 15160/15415/255
Unreserved TBDIDs: 512

OAM table(0x0000CB6C):
0
0x6000CB6C 0x00100274 0x001018BC 0x001018E4 0x0010190C 0x00801934
0x00000240 0x00000274 0x0000195C 0x000045E0 0x00007264

CBR table(0x0000CBA0):
*
EOT(0x0000CBA0) -- entries: 1

VBR1 poll table (0x0000E1E8):

EOT(0x0000E1E8) -- entries: 0
VBR1 redirect table (0x0000E288):
*
DSL SAR Info
EOT(0x0000E288) -- entries: 1

VBR2 poll table (0x0000E210):

EOT(0x0000E210) -- entries: 0
VBR2 redirect table (0x00010F0C):
*
EOT(0x00010F0C) -- entries: 1

VBR3 poll table (0x0000E238):

EOT(0x0000E238) -- entries: 0
VBR3 redirect table (0x00013B90):
*
EOT(0x00013B90) -- entries: 1

VBR4 poll table (0x0000E260):
1 2 3 4 5 6 7 8
EOT(0x0000E260) -- entries: 8
VBR4 redirect table (0x00016814):
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
DSL SAR Info
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8

EOT(0x00016814) -- entries: 288
TCD (vc = 0):
0x0001B000 0x000246D0 0x00040000 0x00005800
0x00840000 0x00005800 0x0F0D8400 0x00040000
0x00040000 0x00000000 0x000006D0 0xFFFFFFFF
0x00000000 0x00000000 0x00000000 0x00000000
TCD (vc = 1):
DSL SAR Info
0x0001C000 0x00025430 0x00000800 0x00008800
0x00000800 0xFFFFFFFF 0x0F1E2800 0x00000800
0x00000800 0x00000000 0x04000250 0x0D127909
0x0ABE025A 0x0F473928 0x000005BA 0x001000B2
TCD (vc = 2):
0x0001D000 0x00026420 0x00000800 0x00008800
0x00000800 0xFFFFFFFF 0x0F1E4C00 0x00000800
0x00000800 0x00000000 0x04000240 0xAFF7CE80
0x0AB900DA 0x0F014948 0x000005BA 0x001000C2
TCD (vc = 3):
0x0001E000 0x00027420 0x00000800 0x00008800
0x00000800 0xFFFFFFFF 0x0F1E5000 0x00000800
0x00000800 0x00000000 0x04000240 0xD6F45716
0x0ABA00DA 0x0F42B128 0x000005BA 0x001000D2
TCD (vc = 4):
0x0001F000 0x00028430 0x00000800 0x00008800
0x00000800 0xFFFFFFFF 0x0F1E5400 0x00000800
0x00000800 0x00000000 0x00000570 0xFFFFFFFF
0x0858001A 0x0F0E87C8 0x000005BA 0x001000E2
TCD (vc = 5):
0x00020000 0x00029740 0x00000800 0x00008800
0x00000800 0xFFFFFFFF 0x0FDEE800 0x00000800
0x00000800 0x00000000 0x04000560 0x09A10FE1
DSL SAR Info
0x0859022A 0x0F0DB5B8 0x000005BA 0x001000F2
TCD (vc = 6):
0x00021000 0x0002A740 0x00000800 0x00008800
0x00000800 0xFFFFFFFF 0x0FDEEC00 0x00000800
0x00000800 0x00000000 0x04000560 0xD2A68842
0x085C034A 0x0F034758 0x000005BA 0x00100102
TCD (vc = 7):
0x00022000 0x0002B740 0x00000800 0x00008800
0x00000800 0xFFFFFFFF 0x0FDF1000 0x00000800
0x00000800 0x00000000 0x04000560 0xC1679389
0x085D031A 0x0F0F6B08 0x000005BA 0x00100112
TCD (vc = 8):
0x00023000 0x0002C740 0x00000800 0x00008800
0x00000800 0xFFFFFFFF 0x0FDF1400 0x00000800
0x00000800 0x00000000 0x04000560 0x7943233E
0x085E031A 0x0F0B1C08 0x000005BA 0x00100122
FIPS-frodo#
The following example uses the show ima interface command to display information about an IMA interface.

show ima interface

Router#show ima interface
Interface ATM0/2/IMA0 is down
Group index is 0, group ifIndex is 11
Ne state is startUp, failure status is noFailure
Active links bitmap 0x0
IMA Group Current Configuration:
Tx/Rx configured links bitmap 0x3/0x3
Tx/Rx minimum required links 1/1
Maximum allowed diff delay is 25ms, Tx frame length 128
Ne Tx clock mode CTC, configured timing reference link Pair 0
Test pattern procedure is disabled
IMA Group Current Counters (time elapsed 0 seconds):
0 Ne Failures, 0 Fe Failures, 0 Unavail Secs
IMA Group Total Counters (last 0 15 minute intervals):
0 Ne Failures, 0 Fe Failures, 0 Unavail Secs
IMA link Information:
Link Physical Status NearEnd Rx Status Test Status
---- --------------- ----------------- -----------
Pair 0 down notInGroup disabled
Pair 1 down notInGroup disabled
Router#
The following example uses the show ima interface detail command to display detailed information about an IMA interface.

show ima interface detail

Router#show ima interface atm 0/2/ima0 detailed
Interface ATM0/2/IMA0 is down
Group index is 0, group ifIndex is 11
Ne state is startUp, failure status is noFailure
Active links bitmap 0x0
IMA Group Current Configuration:
Tx/Rx configured links bitmap 0x3/0x3
Tx/Rx minimum required links 1/1
Maximum allowed diff delay is 25ms, Tx frame length 128
Ne Tx clock mode CTC, configured timing reference link Pair 0
Test pattern procedure is disabled
Detailed group Information:
Ne IMA version in operation IMA Version 1.1
Fe IMA version in operation IMA Version 1.1
Tx/Rx Ima_id 0x0/0xFFFFFFFF, symmetry symmetricOperation
Number of Tx/Rx configured links 2/2
Number of Tx/Rx active links 0/0
Fe Tx clock mode CTC, Rx frame length 128
Tx/Rx timing reference link 0/-1
Maximum observed diff delay 0ms, least delayed link -1
Running seconds 0
GTSM last changed 16:06:16 UTC Wed Oct 4 2006
IMA Group Current Counters (time elapsed 0 seconds):
0 Ne Failures, 0 Fe Failures, 0 Unavail Secs
IMA Group Total Counters (last 0 15 minute intervals):
0 Ne Failures, 0 Fe Failures, 0 Unavail Secs
Detailed IMA link Information:

Link Pair 0 is down
ifIndex 12, Group ifIndex 11, Row Status is active
Tx/Rx Lid -1/-1, relative delay 0ms
Ne Tx/Rx state notInGroup/notInGroup
Fe Tx/Rx state notInGroup/notInGroup
Ne Rx failure status is noFailure
Fe Rx failure status is noFailure
Rx test pattern 0x0, test procedure disabled
IMA Link Current Counters (time elapsed 0 seconds):
0 Ima Violations, 0 Oif Anomalies
0 Ne Severely Err Secs, 0 Fe Severely Err Secs
0 Ne Unavail Secs, 0 Fe Unavail Secs
0 Ne Tx Unusable Secs, 0 Ne Rx Unusable Secs
0 Fe Tx Unusable Secs, 0 Fe Rx Unusable Secs
0 Ne Tx Failures, 0 Ne Rx Failures
0 Fe Tx Failures, 0 Fe Rx Failures
IMA Link Total Counters (last 0 15 minute intervals):
0 Ima Violations, 0 Oif Anomalies
0 Ne Severely Err Secs, 0 Fe Severely Err Secs
0 Ne Unavail Secs, 0 Fe Unavail Secs
0 Ne Tx Unusable Secs, 0 Ne Rx Unusable Secs
0 Fe Tx Unusable Secs, 0 Fe Rx Unusable Secs
0 Ne Tx Failures, 0 Ne Rx Failures
0 Fe Tx Failures, 0 Fe Rx Failures

Link Pair 1 is down
ifIndex 13, Group ifIndex 11, Row Status is active
Tx/Rx Lid -1/-1, relative delay 0ms
Ne Tx/Rx state notInGroup/notInGroup
Fe Tx/Rx state notInGroup/notInGroup
Ne Rx failure status is noFailure
Fe Rx failure status is noFailure
Rx test pattern 0x0, test procedure disabled
IMA Link Current Counters (time elapsed 0 seconds):
0 Ima Violations, 0 Oif Anomalies
0 Ne Severely Err Secs, 0 Fe Severely Err Secs
0 Ne Unavail Secs, 0 Fe Unavail Secs
0 Ne Tx Unusable Secs, 0 Ne Rx Unusable Secs
0 Fe Tx Unusable Secs, 0 Fe Rx Unusable Secs
0 Ne Tx Failures, 0 Ne Rx Failures
0 Fe Tx Failures, 0 Fe Rx Failures
IMA Link Total Counters (last 0 15 minute intervals):
0 Ima Violations, 0 Oif Anomalies
0 Ne Severely Err Secs, 0 Fe Severely Err Secs
0 Ne Unavail Secs, 0 Fe Unavail Secs
0 Ne Tx Unusable Secs, 0 Ne Rx Unusable Secs
0 Fe Tx Unusable Secs, 0 Fe Rx Unusable Secs
0 Ne Tx Failures, 0 Ne Rx Failures
0 Fe Tx Failures, 0 Fe Rx Failures

The following example uses the show atm pvc command to display information about permanent virtual connections (PVCs) and traffic information.

show atm pvc

Router# show atm pvc
VCD / Peak Avg/Min Burst
Interface Name VPI VCI Type Encaps SC Kbps Kbps Cells Sts
0/0/0 1 1 66 PVC SNAP UBR 4608 UP
0/0/0 2 1 77 PVC SNAP UBR 4608 UP
0/0/0 3 1 88 PVC SNAP UBR 4608 UP
0/1/0 1 1 44 PVC SNAP UBR 4608 UP
Router#

Command Reference

This section documents the following new and modified Cisco IOS commands. All other Cisco IOS software commands used with this HWIC are documented in the Cisco IOS Release 12.4(11) XJ command reference publication at Cisco.com:

http://www.cisco.com/en/US/products/ps6441/tsd_products_support_series_home.html

New Commands

• dsl-group, page 25

• ima group clock-mode

• ima link, page 33

• shdsl 4-wire mode

• shdsl annex, page 36

• shdsl rate, page 38

Modified Commands

• controller shdsl

• ima-group

• show controllers shdsl, page 40

controller shdsl

To configure a controller for single-pair high-bit-rate digital subscriber line (SHDSL) mode, use the controller shdsl command in global or controller configuration mode.

Cisco HWIC-4SHDSL and HWIC-2SHDSL

controller shdsl slot number/subslot number/port number
Cisco IAD2420 Series

controller shdsl number
Syntax Description

number

Controller number. The valid controller number is 0.

slot number

Defines the slot on the router in which the high-speed WAN interface cards (HWIC) is installed.

subslot number

Defines the subslot on the router in which the HWIC is installed.

port number

Defines the port on the router in which the HWIC is installed. By default, Cisco HWIC-4SHDSL and HWIC-2SHDSL use port number 0.

Command Defaults

Controller number: 0

Command Modes

Cisco HWIC-4SHDSL and HWIC-2SHDSL

Global configuration

Controller configuration

Cisco IAD2420 Series

Global configuration

Command History

Release

Modification

11.3(5)AAA

This command was introduced.

12.2(8)T

This command was implemented on Cisco IAD2420 series IADs.

12.4(15)T

This command was introduced for the Cisco HWIC-4SHDSL and HWIC-2SHDSL running on the Cisco 1841 router, and on the Cisco 2800 and 3800 series access routers.

Usage Guidelines

This command is used to configure the controller mode and the controller number.

Examples

Cisco HWIC-4SHDSL and HWIC-2SHDSL

The following example uses the controller shdsl command to configure a Cisco HWIC-4SHDSL installed in a Cisco access router, controller number 0, subslot 2, port number 0); the example enters controller configuration mode:

Router(config)# controller shdsl 0/2/0
Router(config-controller)#
Cisco IAD2420 Series

The following example uses the controller shdsl command to enter SHDSL controller mode on controller number 0; the example also configures ATM mode:

Router# controller shdsl 0
Router# mode atm
Related Commands

Command

Description

show controller shdsl

Displays the controller status and statistics.

dsl-group

To create a digital subscriber line (DSL) group and enter config-controller-dsl-group mode, use the dsl-group command in config-controller mode. To disable the DSL group, use the no form of this command.

dsl-group number pairs link number [ima| m-pair]
no dsl-group number pairs link number
Syntax Description

number

Defines the dsl-group number. The dsl-group number can be one of the following numbers:

•0

•1

pairs

Defines the DSL wire pairs.

link number

Designates the pair's link number. Link number options are limited to one of the following choices, based on the hardware interface and the desired DSL group.

HWIC-4SHDSL

IMA DSL Group

•0

•1

•2

•3

•Any combination of the numbers 0,1,2,3

M-Pair DSL Group

•0-1

•0-2

•0-3

2-Pair DSL Group

•0-1

•2-3

1-Pair DSL Group

•0

•1

•2

•3

HWIC-2SHDSL

DSL Group 0

•0

•1

•0-1

DSL Group 1

•1

ima

Defines a DSL group as an inverse multiplexing over ATM (IMA) group.

m-pair

Defines a DSL group as an M-pair group.

Command Default

No DSL group is defined.

Command Modes

Config controller

Command History

Release

Modification

12.4(15)T

This command was introduced for the Cisco HWIC-4SHDSL and HWIC-2SHDSL running on the Cisco 1841 router and the Cisco 2800 and 3800 series access routers.

Usage Guidelines

From config-controller mode, use the dsl-group command to define the DSL group and enter config-controller-dsl-group mode.

Examples

The following example uses the dsl-group command to create an IMA-DSL group and enter config-controller-dsl-group mode:

Router(config-controller)# dsl-group 1 pairs 0-1 ima
Router(config-controller-dsl-group)#
Sep 14 13:15:40.285:%HWIC_SHDSL-5-DSLGROUP_UPDOWN: SHDSL 0/2/0 dsl-group(1) state changed to down.
Sep 14 13:15:42.285:%LINK-3-UPDOWN: Interface ATM0/2/IMA1, changed state to down
Sep 14 13:15:43.285:%LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0/2/IMA1, changed state to down
Related Commands

Command

Description

controller shdsl

Configures a controller for SHDSL mode and enters config-controller mode.

ima group

Defines physical links as IMA group members.

ima group clock-mode

Sets the clock mode for an IMA group.

ima link

Defines physical links in an IMA group.

shdsl 4-wire mode enhanced

Defines the SHDSL to use enhanced mode in a 2-pair DSL group.

shdsl annex

Defines the SHDSL G.991.2 standard.

shdsl rate

Defines the SHDSL rate.

show controller shdsl

Displays the status of the controller that is configured for SHDSL mode.

ima-group

To define inverse multiplexing over ATM (IMA) groups, use the ima-group command in interface configuration mode for Cisco 7100, 7200, and 7500 series routers; use the command in config controller mode for the Cisco HWIC-4SHDSL. To remove the group, use the no form of this command.

Cisco HWIC-4SHDSL

ima-group [shutdown | minimum-links number | clock-mode]
Cisco 7100, 7200, and 7500 series routers

ima-group group-number
no ima-group group-number
Syntax Description

clock-mode

Sets the clock mode for an IMA group

group-number

Specifies an IMA group number from 0 to 3. IMA groups can span multiple ports on a port adapter but cannot span port adapters.

minimum-links number

Defines the number of minimum links that must remain in operation for an IMA group to remain in service.

shutdown

Shuts down physical links in an IMA group.

Command Defaults

No IMA groups are defined.

Command Modes

Cisco HWIC-4SHDSL

Config controller

Config controller DSL group

Cisco 7100, 7200, and 7500 series routers

Interface configuration

Command History

Release

Modification

12.0(5)XK

This command was introduced on Cisco 2600 and 3600 series routers.

12.0(5)T

This command was integrated into Cisco IOS Release 12.0(5)T.

12.0(5)XE

Support for Cisco 7200 and 7500 series routers was added.

12.0(7)XE1

Support for Cisco 7100 series routers was added.

12.1(5)T

Support for Cisco 7100, 7200, and 7500 series routers was added

12.2(33)SRA

This command was integrated into Cisco IOS Release 12.2(33)SRA.

12.4 (11)XJ

This command was integrated into Cisco IOS Release 12.4 (11)XJ.

12.2SX

This command is supported in the Cisco IOS Release 12.2SX train. Support in a specific 12.2SX release of this train depends on your feature set, platform, and platform hardware.

Usage Guidelines

For usage guidelines for using the clock-mode keyword, see the command reference page for the ima group clock-mode command.

Cisco HWIC-4SHDSL

Use the dsl-group command with the optional keyword ima to create an IMA DSL group and to enter config-controller-dsl-group mode. Use the ima group command to define the links as IMA group members.

Cisco 7100, 7200, and 7500 series routers

When the configuration is first performed or when the group number is changed, the interface is automatically disabled, moved to the new group, and then enabled.

Examples

Cisco HWIC-4SHDSL

The following example uses the dsl-group command to create an IMA group and enter config-controller-dsl-group mode on the Cisco HWIC-4SHDSL in a Cisco access router:

Router(config-controller)# dsl-group 1 pairs 0-1 ima
Router(config-controller-dsl-group)#
Sep 26 11:43:55.798: %HWIC_SHDSL-5-DSLGROUP_UPDOWN: SHDSL 0/2/0 dsl-group(1) state changed to down.
Sep 26 11:43:57.798: %LINK-3-UPDOWN: Interface ATM0/2/IMA1, changed state to down
Sep 26 11:43:58.798: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0/2/IMA1, changed state to down

Router (config-controller-dsl-group)# ?
dsl-group configuration sub commands:
default Set a command to its defaults
exit Exit dsl-group sub commands
ima IMA sub commands
no Negate a command or set its defaults
shdsl Symmetric g.shdsl configuration
shutdown Shutdown this dsl-group

Router (config-controller-dsl-group)# ima ?
group IMA group configuration
link IMA link configuration

Router (config-controller-dsl-group)# ima group ?
clock-mode IMA group clock mode configuration
minimum-links Minimum number of active links for group UP
shutdown IMA group shutdown

Cisco 7100, 7200, and 7500 series routers

The following example assigns interface 1 on the ATM module in slot 0 to a member of IMA group 2:

interface atm0/1
ima-group 2
Related Commands

Command

Description

ima group clock-mode

Sets the clock mode for an IMA group.

ima link

Defines physical links for an IMA group.

interface atm

Configures an ATM interface.

interface atm ima

Configures an ATM IMA group.

show ima interface atm

Provides information about all configured IMA groups or a specific IMA group.

shutdown (interface)

Disables an interface.

ima group clock-mode

To set the clock mode for an inverse multiplexing over ATM (IMA) group, use the ima group clock-mode command in config controller DSL group mode. To disable the current configuration, use the no form of this command.

ima group clock-mode {ctc | itc}
no ima group clock-mode
Syntax Description

ctc

Sets the transmit clocks for all the links in the IMA group to be derived from the same source.

itc

Sets the transmit clock source for at least one link in the IMA group to be different from the clock source used by the other links.

Command Defaults

ctc mode

Command Modes

Config controller DSL group

Command History

Release

Modification

12.4(15)T

This command was introduced for the Cisco HWIC-4SHDSL and HWIC-2SHDSL running on the Cisco 1841 router, and Cisco 2800 and 3800 series access routers.

Usage Guidelines

This command controls the clock for the IMA group as a whole. If all the links in the group share a clock source, use the ctc keyword. If all the links use different clock sources, use the itc keyword.

When the ctc keyword is set, the clock source ATM interface configuration command for the common link determines clocking for all the links in the group.When the itc keyword is set, the clock source ATM interface configuration command is used under each interface to determine clocking individually.

Because the system automatically chooses a replacement for the common link when it fails, any link in an IMA group can potentially provide the recovered transmit clock. For this reason, even when the common keyword is set with a specific link stipulated by the port value, you should use the ATM interface configuration clock source command to make sure that the clock source is configured correctly on each interface in the IMA group.

Examples

The following example uses the ima group clock-mode command to configure the clock source for an IMA group:

Router(config-controller-dsl-group)# ima group clock-mode ?
ctc Common Transmit Clock configuration
itc Independent Transmit Clock configuration
Router(config-controller-dsl-group)# ima group clock-mode ctc ?
<cr>
Related Commands

Command

Description

clock source

Configures the clock source of a DS1 link.

interface atm ima

Configures an ATM IMA group.

show ima interface atm

Provides information about all configured IMA groups or a specific IMA group.

ima link

To modify an inverse multiplexing over ATM (IMA) group link, use the ima link command in config controller DSL group mode.

ima link {add | delete | shutdown} number
Syntax Description

add

Adds a link to an IMA group.

delete

Deletes a link from an IMA group. The last link cannot be deleted from an IMA group.

shutdown

Shuts down a link in an IMA group.

number

Defines the IMA link number.

Command Defaults

The default value is a minimum of 1 link.

Command Modes

Config controller DSL group

Command History

Release

Modification

12.4(15)T

This command was introduced for the Cisco HWIC-4SHDSLrunning on the Cisco 1841 router and on the Cisco 2800 and 3800 series access routers.

Usage Guidelines

Use the dsl-group command with the optional keyword, ima, to create an IMA DSL group. Then, use the ima link command to define the links in the IMA group.

Examples

The following example uses the ima link command to modify an IMA DSL group on a Cisco HWIC-4SHDSL that is installed on a Cisco access router:

Router(config-controller-dsl-group)# ima link ? add Add a link to the IMA group
delete Delete a link from the IMA group
shutdown Shutdown a link in the IMA group

Router(config-controller-dsl-group)# ima link add ?
<0-3> Link pair number

Router(config-controller-dsl-group)# ima link add 2 ?
<cr>
Related Commands

Command

Description

interface atm ima

Configures an ATM IMA group.

show ima interface atm

Provides information about all configured IMA groups or a specific IMA group.

shutdown (interface)

Disables an interface.

shdsl 4-wire mode

To define the single-pair high-bit-rate digital subscriber line (SHDSL) to use enhanced mode in a 2-pair digital subscriber line (DSL) group, use the shdsl 4-wire mode command in config controller DSL group mode. To disable shdsl 4-wire mode, use the no form of this command.

shdsl 4-wire mode enhanced
no shdsl 4-wire mode enhanced
Syntax Description

enhanced

Specifies both pairs in a 2-Pair DSL group to operate in a symmetric 4-wire configuration.

Command Default

Standard mode is the default setting.

Command Modes

Config controller DSL group

Command History

Release

Modification

12.4(15)T

This command was introduced for the Cisco HWIC-4SHDSL and HWIC-2SHDSL running on the Cisco 1841 router and on the Cisco 2800 and 3800 series access routers.

Usage Guidelines

Use the dsl-group command to create a 2-Pair DSL group and enter config controller DSL group mode. Use the shdsl 4-wire mode enhanced command to define both pairs to operate in a symmetric 4-wire configuration.

Examples

The following example uses the shdsl 4-wire mode enhanced command to configure both pairs in a 2-Pair DSL group to operate in enhanced mode on the Cisco HWIC-4SHDSL:

Router (config-controller-dsl-group)# shdsl 4-wire mode ?
enhanced 4-wire mode start up on both pairs

Router (config-controller-dsl-group)# shdsl 4-wire mode enhanced ?
<cr>
Related Commands

Command

Description

dsl-group

Creates a DSL group and enters config controller DSL group mode.

shdsl annex

Defines the G.991.2 standard for a DSL group.

shdsl rate

Defines the SHDSL rate.

shdsl annex

To define the single-pair high-bit-rate digital subscriber line (SHDSL) G.991.2 standard, use the shdsl annex command in config controller DSL group mode.

shdsl annex {standard}
Syntax Description

standard

Defines the standard for the selected type of DSL group.

IMA Group

•A

•A-B

•B

M-PAIR Group

•A

•A-B

•B

•F {coding 16 | 32}

•F-G {coding 16 | 32}

•G {coding 16 | 32}

1-PAIR and 2-PAIR Group

•A

•A-B

•B

•F {coding 16 | 32}

•F-G {coding 16 | 32}

•G {coding 16 | 32}

Command Default

SHDSL annex B

Command Modes

Config controller DSL group

Command History

Release

Modification

12.4(15)T

This command was introduced for the Cisco HWIC-4SHDSL and HWIC-2SHDSL running on the Cisco 1841 router and on the Cisco 2800 and 3800 series access routers.

Usage Guidelines

Use the dsl-group command to create a DSL group, and then use the shdsl annex command to define the G.991.2 standard for the DSL group.

Examples

The following example uses the shdsl annex command to define the annex standard for a 2-Pair DSL group on a Cisco HWIC-4SHDSL:

Router(config-controller-dsl-group)# shdsl annex ?
A Annex A of G.991.2 standard
A-B Annex A/B of G.991.2 standard
B Annex B of G.991.2 standard
F Annex F of G.991.2 standard
F-G Annex F/G of G.991.2 standard
G Annex G of G.991.2 standard

Router(config-controller-dsl-group)# shdsl annex g ?
coding 16-TCPAM or 32-TCPAM line coding

Router(config-controller-dsl-group)# shdsl annex g coding ?
16-TCPAM 16-TCPAM line coding
32-TCPAM 32-TCPAM line coding

Router(config-controller-dsl-group)# shdsl annex g coding 16 ?
<cr>
Related Commands

Command

Description

dsl-group

Creates a DSL group and enters config controller DSL group mode.

shdsl rate

Defines the SHDSL rate.

shdsl rate

To define the single-pair high-bit-rate digital subscriber line (SHDSL) rate, use the shdsl rate command in config-controller-dsl-group mode.

shdsl rate {number | auto}
Syntax Description

number

Defines the SHDSL rate for the digital subscriber line (DSL) group.

DSL Group with 1 Pair

Annex A & B—192-2304 kbps

Annex F & G (32 TC-PAM)—768-5696 kbps

Annex F & G (16 TC-PAM)—2304-3840 kbps

DSL Group with 2 Pairs

Annex A & B—384-4608 kbps

Annex F & G (32 TC-PAM)—1536-11392 kbps

Annex F & G (16 TC-PAM)— 4608-7680 kbps

DSL Group with 3 Pairs

Annex A & B—576-6912 kbps

Annex F & G (32 TC-PAM)—2304-12288 kbps

Annex F & G (16 TC-PAM)— 6912-11520 kbps

DSL Group with 4 Pairs

Annex A & B—768-9216 kbps

Annex F & G (32 TC-PAM)—3072-16384 kbps

Annex F & G (16 TC-PAM)— 9216-15360 kbps

auto

Sets this SHDSL rate to automatic mode.

Command Default

The command default is the maximum annex rate for the selected DSL group.

Command Modes

Config controller DSL group

Command History

Release

Modification

12.4(15)T

This command was introduced for the Cisco HWIC-4SHDSL and HWIC-2SHDSL running on the Cisco 1841 router and on the Cisco 2800 and 3800 series access routers.

Usage Guidelines

Use the dsl-group command to create a DSL group, and then use the shdsl annex command to define the G.991.2 standard for the newly created DSL group. Define the SHDSL line rate with the shdsl rate command.

Examples

The following example defines the SHDSL line rate for DSL group 1, pairs 0-1 (2 pairs) on a Cisco HWIC-4SHDSL:

Router(config-controller)# dsl-group 1 pairs 0-1 ima
Router(config-controller-dsl-group)#
Sep 22 14:53:46.481: %HWIC_SHDSL-5-DSLGROUP_UPDOWN: SHDSL 0/2/0 dsl-group(1) state changed to down.
Sep 22 14:53:48.481: %LINK-3-UPDOWN: Interface ATM0/2/IMA1, changed state to down
Sep 22 14:53:49.481: %LINEPROTO-5-UPDOWN: Line protocol on Interface ATM0/2/IMA1, changed state to down

Router(config-controller-dsl-group)# shdsl annex ?
A Annex A of G.991.2 standard
A-B Annex A/B of G.991.2 standard
B Annex B of G.991.2 standard

Router(config-controller-dsl-group)# shdsl annex b ?
<cr>
Router(config-controller-dsl-group)# shdsl rate auto
<384-4608> DSL Rate in kbps(line will train at the rate + 16kbps overhead)
auto auto rate mode
Related Commands

Command

Description

dsl-group

Creates a DSL group and enters config controller DSL group mode.

shdsl annex

Defines the G.991.2 standard for a DSL group.

show controllers shdsl

To display the status of the controller configured for single-pair high-bit-rate digital subscriber line (SHDSL) mode, use the show controllers shdsl command in privileged EXEC mode.

Cisco HWIC-4SHDSL and HWIC-2SHDSL

show controllers shdsl slot number/subslot number/port number {brief | detailed}
Cisco IAD2420

show controller shdsl number
Syntax Description

brief

Provides a summary of the controller's status.

detailed

Provides a detailed report of the controller's status.

number

SHDSL controller number. The valid controller number for SHDSL mode is 0.

slot number

Identifies the slot on the router in which the HWIC is installed.

subslot number

Identifies the subslot on the router in which the HWIC is installed.

port number

Identifies the port on the router in which the HWIC is installed. By default, the Cisco HWIC-4SHDSL and HWIC-2SHDSL use port number 0.

Command Defaults

Controller number

Command Modes

Privileged EXEC

Command History

Release

Modification

12.4(15)T

This command was updated for the Cisco HWIC-4SHDSL and HWIC-2SHDSL running on the Cisco 1841 router and on the Cisco 2800 and 3800 series access routers.

12.2(8)T

This command was introduced on Cisco IAD2420 series.

Usage Guidelines

This command is used to display the controller mode, the controller number, and associated statistics.

Examples

Cisco HWIC-4SHDSL and HWIC-2SHDSL

The following example displays the status of a Cisco HWIC-4SHDSL controller in slot 0, subslot 2, port 0 on a Cisco access router:

Router# show controllers shdsl 0/2/0 brief
Controller SHDSL 0/2/0 is UP
Hardware is HWIC-4SHDSL, rev 2 on slot 0, hwic slot 2
Capabilities: IMA, M-pair, 2/4 wire, Annex A, B, F & G, CPE termination
cdb=0x43EB384C, plugin=0x43DE9410, ds=0x43E9A1C4 base=0xB8000000
FPGA Version is REL.3.4.0, NIOSII FW:Ver 2.6, status Running
SDC-16i HW:Rev 1.2, status UP, FW:Ver 1.2-1.1.3__57, status Running
SDFE-4 HW:Rev 1.2, status UP, FW:Ver 1.1-1.5.2__001 , status Running
NIOSII Firmware image: System
SDC16i Firmware image: System
SDFE4 Firmware image: System
Number of pairs 4, number of groups configured 1
Ignored CLI cmds(0), Event buffer: in use(0), failed(0)
Group (0) is Not configured.
Group (1) info:
Type: M-pair over g.shdsl, status: Configure Firmware
Interface: ATM0/2/1, hwidb: 0x43F04EA0, UTOPIA phy 1
Configured/active num links: 2/0, bit map: 0x3/0x0
Line termination: CPE, line mode: M-pair, Annex-B, PMMS disabled
Line coding: 16-TCPAM, configured/actual rate: 4608/0 kbps
SHDSL wire-pair (0) is in DSL DOWN state
SHDSL wire-pair (1) is in DSL config state
Router#
Cisco IAD2420 Series

The following example displays the status of the controller that is configured for SHDSL mode on a Cisco IAD2420 series IAD:

Router# show controller shdsl 0

SHDSL 0 controller UP
SLOT 3: Globespan xDSL controller chipset
Frame mode: Serial ATM
Configured Line rate: 1160Kbps
Line Re-activated 0 times after system bootup
LOSW Defect alarm: None
CRC per second alarm: None
Line termination: CPE
FPGA Revision: 9
Related Commands

Command

Description

controller shdsl 0

Configures the controller status and the controller number.

Additional References

The following references provide links to related topics, such as the Cisco IOS software resource center, interface card documentation, and additional hardware documentation.

Related Documents

Related Topic

Document Title

Cisco IOS software

Cisco IOS Software http://www.cisco.com/en/US/products/sw/iosswrel/tsd_products_support_category_home.html

Interface Cards

Cisco Interface Cards Hardware Installation Guide

http://www.cisco.com/en/US/products/hw/modules/ps2641/products_module_installation_guide_book09186a0080692b21.html

Cisco Network Modules and Interface Cards Regulatory Compliance and Safety Information

http://www.cisco.com/en/US/products/hw/modules/ps2797/products_regulatory_approvals_and_compliance09186a0080183b96.html

Technical documentation, including feedback and assistance

What's New in Cisco Product Documentation (including monthly listings of new and revised documents) at http://www.cisco.com/univercd/cc/td/doc/abtunicd/136957.htm

Standards

Standard

Title

•ITU G.991.2

–Annex A

–Annex B

–Annex F

–Annex G

•af-phy-0086.001

–Inverse Multiplexing over ATM version 1.1

MIBs

MIB

MIBs Link

•Entity MIB

•Chassis MIB

•Interface MIB

•AToM MIB

•ILMI MIB

•IMA MIB

•HDSL2-SHDSL-LINE MIB

To locate and download MIBs for selected platforms, Cisco IOS releases, and feature sets, use Cisco MIB Locator found at the following URL:

http://www.cisco.com/go/mibs

RFCs

RFC

Title

•G.SHDSL— RFC# 3276

•HDSL2-SHDSL-LINE MIB

Technical Assistance

Description

Link

The Cisco Technical Support & Documentation website contains thousands of pages of searchable technical content, including links to products, technologies, solutions, technical tips, and tools. Registered Cisco.com users can log in from this page to access even more content.

http://www.cisco.com/techsupport

Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental.

� 2006 Cisco Systems, Inc. All rights reserved.

	Command	Purpose
Step 1	`controller shdsl slot number/subslot number/0 Example: Router (config)# controller shdsl 0/2/0` Router (config-controller)#	Selects the controller and enters config-controller mode. See the "controller shdsl" section for more information.
Step 2	dsl-group number pairs link number [ima \| m-pair] Example: Router (config-controller)# dsl-group 0 pairs 0-3 ima	Creates a DSL group and enters config-controller-dsl-group mode. See the "dsl-group" section on page 25 for more information.
Step 3	ima link {add \| delete \| shutdown}number Example: Router (config-controller-dsl-group)# ima link add 2	Modifies links in an IMA group. See the "ima link" section on page 33 for more information.
Step 4	ima group {shutdown\|minimum-links number \| clock-mode} Example: Router (config-controller-dsl-group)# ima group minimum-links 2	Modifies IMA group behavior. See the "ima-group" section for more information.
Step 5	ima group clock-mode {ctc \| itc} Example: Router (config-controller-dsl-group)# ima group clock-mode ctc	Defines the clock mode for an IMA group. See the "ima group clock-mode" section for more information.
Step 6	shdsl annex {standard} Example: Router (config-controller-dsl-group)# shdsl annex A	Defines the SHDSL annex. See the "shdsl annex" section on page 36 for more information.
Step 7	shdsl rate {number \| auto} Example: Router (config-controller-dsl-group)# shdsl rate auto	Defines the SHDSL rate. See the "shdsl rate" section on page 38 for more information.
Step 8	exit Example: Router (config-controller-dsl-group)# exit	Exits config-controller-dsl-group mode.
Step 9	exit Example: Router (config-controller)# exit	Exits config-controller mode.

	Command	Purpose
Step 1	`controller shdsl slot number/subslot number/0 Example: Router (config)# controller shdsl 0/2/0` Router (config-controller)#	Selects the controller and enters config-controller mode. See the "controller shdsl" section for more information.
Step 2	dsl-group number pairs link number Example(1-pair group): Router (config-controller)# dsl-group 0 pairs 0 Example(2-pair group): Router (config-controller)# dsl-group 0 pairs 0-1	Creates a DSL group and enters config-controller-dsl-group mode. See the "dsl-group" section on page 25 for more information.
Step 3	shdsl 4-wire mode enhanced Example: Router (config-controller)# shdsl 4-wire mode enhanced	Defines a 2-pair group as enhanced. See the "shdsl 4-wire mode" section for more information.
Step 4	shdsl annex {standard} Example: Router (config-controller-dsl-group)# shdsl annex A-B	Defines the SHDSL annex. See the "shdsl annex" section on page 36 for more information.
Step 5	shdsl rate {number\|auto} Example: Router (config-controller)# shdsl rate 2048	Defines the SHDSL rate. See the "shdsl rate" section on page 38 for more information.
Step 6	exit Example: Router (config-controller-dsl-group)# exit	Exits config-controller-dsl-group mode.
Step 7	exit Example: Router (config-controller)# exit	Exits config-controller mode.

EN	Status of the system: Green—Operating system is running. Amber—Interface card is resetting. Blinking—System is initializing.
L0, L1, L2, L3	Status of link: On—Link is active. Off—Link is inactive (disabled). Blinking— Link is training / Link alarm

Pin	Signal
1	Line 1 tip
2	Line 1 ring
3	Line 2 tip
4	Line 0 tip
5	Line 0 ring
6	Line 2 ring
7	Line 3 tip
8	Line 3 ring

	Command	Purpose
Step 1	`show controllers shdsl slot number/subslot number/0 [detailed \| brief] Example: Router# show controllers shdsl 0/2/0 detailed`	Displays the status of SHDSL controllers. See the "show controllers shdsl" section on page 40 for more information.
Step 2	show controllers atm [slot/subslot number/imagroup-number] `Example: Router# show controllers atm 0/1/ima0`	Displays information about the IMA group.
Step 3	show ima interface `Example: Router# show ima interface`	Displays information about the IMA interface.
Step 4	show ima interface atm [slot/subslot number/imagroup-number] [detailed] `Example: Router# show ima interface atm 0/1/ima0`	Displays detailed information about the IMA interface.
Step 5	show atm pvc `Example: Router# show atm pvc`	Displays information about ATM permanent virtual connections (PVCs) and traffic information.

number	Controller number. The valid controller number is 0.
slot number	Defines the slot on the router in which the high-speed WAN interface cards (HWIC) is installed.
subslot number	Defines the subslot on the router in which the HWIC is installed.
port number	Defines the port on the router in which the HWIC is installed. By default, Cisco HWIC-4SHDSL and HWIC-2SHDSL use port number 0.

Release	Modification
11.3(5)AAA	This command was introduced.
12.2(8)T	This command was implemented on Cisco IAD2420 series IADs.
12.4(15)T	This command was introduced for the Cisco HWIC-4SHDSL and HWIC-2SHDSL running on the Cisco 1841 router, and on the Cisco 2800 and 3800 series access routers.

number	Defines the dsl-group number. The dsl-group number can be one of the following numbers: •0 •1
pairs	Defines the DSL wire pairs.
link number	Designates the pair's link number. Link number options are limited to one of the following choices, based on the hardware interface and the desired DSL group. HWIC-4SHDSL IMA DSL Group •0 •1 •2 •3 •Any combination of the numbers 0,1,2,3 M-Pair DSL Group •0-1 •0-2 •0-3 2-Pair DSL Group •0-1 •2-3 1-Pair DSL Group •0 •1 •2 •3
	HWIC-2SHDSL DSL Group 0 •0 •1 •0-1 DSL Group 1 •1
ima	Defines a DSL group as an inverse multiplexing over ATM (IMA) group.
m-pair	Defines a DSL group as an M-pair group.

Command	Description
controller shdsl	Configures a controller for SHDSL mode and enters config-controller mode.
ima group	Defines physical links as IMA group members.
ima group clock-mode	Sets the clock mode for an IMA group.
ima link	Defines physical links in an IMA group.
shdsl 4-wire mode enhanced	Defines the SHDSL to use enhanced mode in a 2-pair DSL group.
shdsl annex	Defines the SHDSL G.991.2 standard.
shdsl rate	Defines the SHDSL rate.
show controller shdsl	Displays the status of the controller that is configured for SHDSL mode.

clock-mode	Sets the clock mode for an IMA group
group-number	Specifies an IMA group number from 0 to 3. IMA groups can span multiple ports on a port adapter but cannot span port adapters.
minimum-links number	Defines the number of minimum links that must remain in operation for an IMA group to remain in service.
shutdown	Shuts down physical links in an IMA group.

Release	Modification
12.0(5)XK	This command was introduced on Cisco 2600 and 3600 series routers.
12.0(5)T	This command was integrated into Cisco IOS Release 12.0(5)T.
12.0(5)XE	Support for Cisco 7200 and 7500 series routers was added.
12.0(7)XE1	Support for Cisco 7100 series routers was added.
12.1(5)T	Support for Cisco 7100, 7200, and 7500 series routers was added
12.2(33)SRA	This command was integrated into Cisco IOS Release 12.2(33)SRA.
12.4 (11)XJ	This command was integrated into Cisco IOS Release 12.4 (11)XJ.
12.2SX	This command is supported in the Cisco IOS Release 12.2SX train. Support in a specific 12.2SX release of this train depends on your feature set, platform, and platform hardware.

Command	Description
ima group clock-mode	Sets the clock mode for an IMA group.
ima link	Defines physical links for an IMA group.
interface atm	Configures an ATM interface.
interface atm ima	Configures an ATM IMA group.
show ima interface atm	Provides information about all configured IMA groups or a specific IMA group.
shutdown (interface)	Disables an interface.

ctc	Sets the transmit clocks for all the links in the IMA group to be derived from the same source.
itc	Sets the transmit clock source for at least one link in the IMA group to be different from the clock source used by the other links.

Command	Description
clock source	Configures the clock source of a DS1 link.
interface atm ima	Configures an ATM IMA group.
show ima interface atm	Provides information about all configured IMA groups or a specific IMA group.

add	Adds a link to an IMA group.
delete	Deletes a link from an IMA group. The last link cannot be deleted from an IMA group.
shutdown	Shuts down a link in an IMA group.
number	Defines the IMA link number.

Command	Description
dsl-group	Creates a DSL group and enters config controller DSL group mode.
shdsl annex	Defines the G.991.2 standard for a DSL group.
shdsl rate	Defines the SHDSL rate.

number	Defines the SHDSL rate for the digital subscriber line (DSL) group. DSL Group with 1 Pair Annex A & B—192-2304 kbps Annex F & G (32 TC-PAM)—768-5696 kbps Annex F & G (16 TC-PAM)—2304-3840 kbps DSL Group with 2 Pairs Annex A & B—384-4608 kbps Annex F & G (32 TC-PAM)—1536-11392 kbps Annex F & G (16 TC-PAM)— 4608-7680 kbps DSL Group with 3 Pairs Annex A & B—576-6912 kbps Annex F & G (32 TC-PAM)—2304-12288 kbps Annex F & G (16 TC-PAM)— 6912-11520 kbps DSL Group with 4 Pairs Annex A & B—768-9216 kbps Annex F & G (32 TC-PAM)—3072-16384 kbps Annex F & G (16 TC-PAM)— 9216-15360 kbps
auto	Sets this SHDSL rate to automatic mode.

brief	Provides a summary of the controller's status.
detailed	Provides a detailed report of the controller's status.
number	SHDSL controller number. The valid controller number for SHDSL mode is 0.
slot number	Identifies the slot on the router in which the HWIC is installed.
subslot number	Identifies the subslot on the router in which the HWIC is installed.
port number	Identifies the port on the router in which the HWIC is installed. By default, the Cisco HWIC-4SHDSL and HWIC-2SHDSL use port number 0.

Release	Modification
12.4(15)T	This command was updated for the Cisco HWIC-4SHDSL and HWIC-2SHDSL running on the Cisco 1841 router and on the Cisco 2800 and 3800 series access routers.
12.2(8)T	This command was introduced on Cisco IAD2420 series.

Related Topic	Document Title
Cisco IOS software	Cisco IOS Software http://www.cisco.com/en/US/products/sw/iosswrel/tsd_products_support_category_home.html
Interface Cards	Cisco Interface Cards Hardware Installation Guide http://www.cisco.com/en/US/products/hw/modules/ps2641/products_module_installation_guide_book09186a0080692b21.html Cisco Network Modules and Interface Cards Regulatory Compliance and Safety Information http://www.cisco.com/en/US/products/hw/modules/ps2797/products_regulatory_approvals_and_compliance09186a0080183b96.html
Technical documentation, including feedback and assistance	What's New in Cisco Product Documentation (including monthly listings of new and revised documents) at http://www.cisco.com/univercd/cc/td/doc/abtunicd/136957.htm

Standard	Title
•ITU G.991.2	–Annex A –Annex B –Annex F –Annex G
•af-phy-0086.001	–Inverse Multiplexing over ATM version 1.1