cc/td/doc/product/access/acs_fix/cis2000
hometocprevnextglossaryfeedbacksearchhelp
PDF

Table of Contents

Cisco 2000 Series Hardware Installation

Cisco 2000 Series Hardware Installation

Following is the information required to install the router chassis.

About This Guide

Follow this procedural path to install your router:


  1. Install the router hardware using the procedures described in this publication.

  2. After the hardware is installed, refer the Router Products Getting Started Guide or to the appropriate software publication to configure the router.

  3. Refer to the "Reference" section in this publication for cabling and basic troubleshooting information.

Installation

This section guides you through the installation of the router and includes information on safety, inspecting the system, preventing electrostatic discharge (ESD) damage, tools and parts required, rack mounting, wall mounting, and making external cable connections.


Note If you have questions about agency approvals, basic troubleshooting, system specifications, or specific cable pinout information, review the information in the section "Reference" on page 9.

Safety Recommendations

Follow these guidelines to ensure general safety:

Warning Before working on equipment that is connected to power lines, remove jewelry (including rings, necklaces, and watches). Metal objects will heat up when connected to power and ground and can cause serious burns or weld the metal object to the terminals.

Inspecting the System

Do not unpack the router until you are prepared to install it. If the final installation site will not be ready for some time, keep the router in the shipping container to prevent accidental damage. When you have determined where you want the router installed, proceed with the unpacking. The router, cables, publications, and any optional equipment you ordered might be shipped in more than one container. When you unpack each shipping container, check the packing list to ensure that you received all of the following items:

Inspect all items for shipping damage. If anything appears damaged, or if you encounter problems when installing or configuring your system, contact a service representative.

Preventing Electrostatic Discharge Damage

Electrostatic discharge (ESD) can damage equipment and impair electrical circuitry. It occurs when electronic printed circuit cards are improperly handled and can result in complete or intermittent failures. Always follow ESD prevention procedures when removing and replacing cards. Ensure that the router chassis is electrically connected to earth ground. Wear an ESD wrist strap, ensuring that it makes good skin contact. Connect the clip to an unpainted chassis frame surface to safely channel unwanted ESD voltages to ground. To properly guard against ESD damage and shocks, the wrist strap and cord must operate effectively. If no wrist strap is available, ground yourself by touching the metal part of the chassis.

Caution For safety, periodically check the resistance value of the antistatic strap, which should be within the range of 1 and 10 Mohms.

Tools and Parts Required

Following are the tools and parts required to install the router:

In addition, you might need the following additional external equipment:

Information on Mounting the Router on a Rack or Wall

Rack and wall mounting procedures are described in a separate publication included with the optional rack mount kit. If you intend to rack mount the router, do so before making the external connections.

Preparing for External Connections

Following are the procedures for making external connections to the router. Figure 1 shows the rear panel of the router with the following connectors:




Figure 1: Router Front and Rear View--Models 2102 and 2202

Information for United Kingdom Use Only

Cisco Systems declaration of operating conditions:

The Cisco 2000 is designed to meet the requirements of NET1 and NET2.

Warnings

Interconnection directly, or by way of other apparatus, of ports marked:

"Safety Warning -- See instructions for use"

with ports marked or not so marked may produce hazardous conditions on the network and that advice should be obtained from a competent engineer before such a connection is made.

The ports marked "Ethernet," "Token Ring," "Console," and "AUX" have a safety warning applied to them as follows:

"These ports do not provide isolation sufficient to satisfy the requirement of BS6301; apparatus connected to these ports should either have been approved to BS6301 or have previously been evaluated against British Telecommunications plc (Post Office) Technical Guides 2 or 26 and given permission to attach; any that other usage will invalidate any approval given to this apparatus."

Connection of Power Supply. The Cisco 2000 is intended for use when supplied with power from a supply providing 220-240 VAC, 50/60 Hz up to 5 Amps.

Other usage will invalidate any approval given to this apparatus if as a result it ceases to comply with BS6301: 1989.

The Cisco 2000 is brought into service by the supplier.

Information for European Community Use Only

The ports marked "Ethernet," "Token Ring," "Console," and "AUX" are SELV circuits. SELV circuits should only be connected to other SELV circuits.

Making External Connections

Follow these steps to make external connections to your router:

Step 1 Connect the Ethernet port to the network as shown in Figure 2.




Figure 2: Ethernet Transition Cable Connections

Step 2 Extend the Ethernet cable as shown in Figure 3.




Figure 3: Extending the Transition Cable from the Router's Ethernet Port

Step 3 Connect the Token Ring port to the network as shown in Figure 4.




Figure 4: Token Ring Cable Connections

Step 4 Connect the serial ports to the network as shown in Figure 5.




Figure 5: Serial Cable Connections

Step 5 Connect the console and auxiliary ports as required for your method of configuration. Your terminal should be configured for 9600 baud, 8 data bits, no parity, and 1 stop bits.

Step 6 Connect the power cable between the router and the AC source.

What to Do after the Router Hardware Is Installed

After the router hardware is installed, the system is ready to be powered on and configured. For software configuration information, refer to the following publications:

To order these or additional associated publications, refer to the Service and Support card that accompanied your router.

Reference

This section includes the following reference information:


Note For additional information on the Cisco 2000 router, refer to the Cisco 2000 Quick-Start Guide. For information on installing the router hardware, refer to the section "Installation" on page 1 of this publication.

Troubleshooting

The key to problem solving in this system is to try to isolate the problem to a specific subsystem. By comparing what the system is doing to what it should be doing, the task of isolating a problem is greatly simplified.

Check the following items to help isolate the problem:

The System OK LED should be on after the system initializes correctly. (See Figure 1.)


Note If an interface is extremely busy, the corresponding LED will be on all the time.

System Specifications

Following are the specifications for the router system.


System Specifications
Description Design Specification
Dimensions H x W x D 13" x 14" x 4" (33 x 35.6 x 10 cm)
Weight 15 lb (6.8 kg)
Input voltage, frequency, and power dissipation 110/220 VAC at 50 through 60 Hz
55W (max.)
273 Btu/hr
Processor Motorola 68EC030--20 MHz
Memory 1-MB primary memory
512-KB shared memory
32-KB nonvolatile configuration RAM
Network interface options 1 Ethernet and 1 synchronous serial (2102)
or 1 Token Ring and 1 synchronous serial (2202)
Ethernet interfaces AUI1 IEEE 802.3 (DB-15)
Token Ring IEEE 802.5 (DB-9)
Synchronous serial interfaces RS-232, RS-449, V.35, X.21, EIA-530
Console port Asynchronous RS-232 DB-25 female connector
Auxiliary port Asynchronous RS-232 DB-25 male connector
Operating environment 32 to 104×F (0 to 40×C )
Nonoperating temperature -40 to 185×F (-40 to 85×C)
Operating humidity 5 to 95%, noncondensing
Noise level 40 dBa

1 AUI = Attachment unit interface.

Cable Pinouts

The following tables list the pinouts for the cables that can be used with the router:


Note In the following tables, pinouts representing DTE and DCE cables use arrows to indicate signal direction: --> indicates DTE to DCE, <-- indicates DCE to DTE.

For more detailed pinout information, refer to the Cisco 2000 Quick-Start Guide.


Console Asynchronous Serial Port RS-232 Pinout (25-Pin D Connector)
Pin1 Signal Name Direction
1 Frame Ground -
2 Transmitted Data Input
3 Received Data Output
4 Request To Send Shorted together internally with pin 5
5 Clear To Send -
6 Shorted to pin 8 Output
7 Ground -
8 Carrier Detect Output
20 Data Terminal Ready Input

Auxiliary Asynchronous Serial Port RS-232 Pinout (25-Pin D Connector)
Pin2 Signal Name Direction
1 Frame Ground -
2 Transmitted Data Output
3 Received Data Input
4 Request To Send Output
5 Clear To Send Input
7 Ground -
8 Carrier Detect Input
20 Data Terminal Ready Output
22 Ring Indicator Input

EIA-530 DTE Serial Cable Pinout
Part Number 72-0732-01 Connections
50 Pin1 Signal Name Direction 25 Pin Type
J1-5
J1-38
Looped NC Jumper
J1-1
J1-34
TXD +
TXD -
-->
-->
J2-2
J2-14
Twisted Pair
J1-35
J1-19
RXD +
RXD -
<--
<--
J2-3
J2-16
Twisted Pair
J1-4
J1-20
RTS +
RTS -
-->
-->
J2-4
J2-19
Twisted Pair
J1-6
J1-22
CTS +
CTS -
<--
<--
J2-5
J2-13
Twisted Pair
J1-10
J1-26
RLSD + (RR +)
RLSD - (RR -)
<--
<--
J2-8
J2-10
Twisted Pair
J1-2
J1-18
SCT +
SCT -
<--
<--
J2-15
J2-12
Twisted Pair
J1-37
J1-21
SCR +
SCR -
<--
<--
J2-17
J2-9
Twisted Pair
J1-43
J1-27
SCTE + (TT +)
SCTE - (TT -)
<--
<--
J2-24
J2-11
Twisted Pair
J1-7 LL --> J2-18 Twisted Pair
J1-48
J1-36
Ground J2-23
J2-7
Twisted Pair
J1-15 Shield J2-1 Single Wire
J1-8
J1-24
DCE Ready
Ground
<-- J2-6
J2-23
Twisted Pair
J1-41 DTE Ready --> J2-20 Twisted Pair

1 Any pin not referenced on a connector is not connected.

RS-232 DTE Serial Cable Pinout
Part Number 72-0670-01 Connections3
50 Pin 25 Pin Type
J1-3 J1-36
J1-39
J1-40
J2-5
J2-4
Twisted Pair
J1-9
J1-42
J2-8
J2-6
Twisted Pair
J1-11
J1-44
J2-2
J2-7
Twisted Pair
J1-46
J1-30
J2-3
J2-20
Twisted Pair
J1-14
J1-47
J2-18
J2-17
Twisted Pair
J1-31
J1-15
J2-15
J2-1
Twisted Pair
J1-16 J2-24 Twisted Pair

RS-449 DTE Serial Cable Pinout
Part Number 72-0672-01 Connections
50 Pin1 37 Pin Type
J1-5 J1-38
J1-7 J2-10
J1-1
J1-34
J2-4
J2-22
Twisted Pair
J1-2
J1-18
J2-5
J2-23
Twisted Pair
J1-35
J1-19
J2-6
J2-24
Twisted Pair
J1-4
J1-20
J2-7
J2-25
Twisted Pair
J1-37
J1-21
J2-8
J2-26
Twisted Pair
J1-22
J1-6
J2-27
J2-9
Twisted Pair
J1-8
J1-24
J2-11
J2-29
Twisted Pair
J1-41
J1-25
J2-12
J2-30
Twisted Pair
J1-10
J1-26
J2-13
J2-31
Twisted Pair
J1-43
J1-27
J2-17
J2-35
Twisted Pair
J1-36
J1-15
J2-19
J2-1
Twisted Pair
J1-44
J1-48
J2-37
J2-20
Twisted Pair

1 Any pin not referenced on a connector is not connected.

V.35 DTE Serial Cable Pinout
Part Number 72-0671-02 Connections
50 Pin1 34 Pin Type Signal Direction
J1-3 J1-36 Jumper MUX To Ground
J1-5 J1-38 Jumper MUX To Ground
J1-14

J1-Shield

J2-K
J2-Shield
Twisted Pair LTST
Not Used
-->
J1-2
J1-18
J2-Y
J2-AA
Twisted Pair SCT +
SCT -
<--
<--
J1-12
J1-28
J2-P
J2-S
Twisted Pair TXD +
TXD -
-->
-->
J1-35
J1-19
J2-R
J2-T
Twisted Pair RXD +
RXD -
<--
<--
J1-37
J1-21
J2-V
J2-X
Twisted Pair SCR +
SCR -
<--
<--
J1-45
J1-29
J2-U
J2-W
Twisted Pair SCTE +
SCTE -
-->
-->
J1-42
J1-Shield
J2-E
J2-Shield
Twisted Pair DSR
Not Used
<--
J1-9
J1-48
J2-F
J2-A
Twisted Pair RLSD
Ground
<--
<--
J1-40
J1-Shield
J2-C
J2-Shield
Twisted Pair RTS
Not Used
-->
J1-2
J1-18
J1-3
J1-5
Resistor
Resistor
SCT +
SCT -
R To
Ground
J1-35
J1-19
J1-36
J1-38
Resistor
Resistor
RXD +
RXD -
R To
Ground
J1-37
J1-21
J1-44
J1-48
Resistor
Resistor
SCR +
SCR -
R To
Ground
J1-30
J1-44
J2-H
J2-B
Twisted Pair DTR
Ground
-->
-->
J1-39
J1-Shield
J2-D
J2-Shield
Twisted Pair CTS
Not Used
-->
J1-Shield
J1-Shield
J2-Shield
J2-Shield
Twisted Pair Not Used
Not Used
J1-Shield J2-Shield Single Not Used

1 Any pin not referenced on a connector is not connected.

X.21 DTE Serial Cable Pinout
Part Number 72-0683-02 Connections4
From Signal Type To Signal
J1-5 MUX SEL J1-38 GND
J1-36 449 GND J2-8 X.21 GND
J1-41
J1-25
449 DTR Jumper J1-6
J1-22
449 CTS
J1-41
J1-25
449 DTR Jumper J1-8
J1-24
449 DSR
J1-43
J1-27
449 SCTE Jumper J1-37
J1-21
449 SCR
J1-1
J1-34
449 TXD Twisted Pair J2-2
J2-9
X.21 TXD
J1-4
J1-20
449 RTS Twisted Pair J2-3
J2-10
X.21 CTL
J1-35
J1-19
449 RXD Twisted Pair J2-4
J2-11
X.21 RXD
J1-10
J1-26
449 RLSD Twisted Pair J2-5
J2-12
X.21 IND
J1-2
J1-18
449 SCT Twisted Pair J2-6
J2-13
X.21 CLK

Ethernet (AUI) Port Pinout
Pin5 Ethernet Circuit Signal
1 CI-S Control In Circuit Shield
2 CI-A Control In Circuit A
3 DO-A Data Out Circuit A
4 DI-S Data In Circuit Shield
5 DI-A Data In Circuit A
6 VC Voltage Common
7 CO-A Control Out Circuit A (not connected)
8 CO-S Control Out Circuit Shield (not connected)
9 CI-B Control In Circuit B
10 DO-B Data Out Circuit B
11 DO-S Data Out Circuit Shield
12 DI-B Data In Circuit B
13 VP Voltage Plus
14 VS Voltage Shield (L25 and M25)
15 CO-B Control Out Circuit B (not connected)
Shell PG Protective Ground

Token Ring Port Pinout (DB-9)
9-Pin Signal
1 -RX
2 NC1
3 NC
4 NC
5 -TX
6 +RX
7 NC
8 NC
9 +TX

1 NC stands for not connected.


1 &&Center&&Any pin not referenced on a connector is not connected.
2 &&Center&&Any pin not referenced on a connector is not connected.
3 &&Center&&Any pin not referenced on a connector is not connected.
4 Any pin not referenced on a connector is not connected.
5 &&Center&&Any pin not referenced on a connector is not connected.

hometocprevnextglossaryfeedbacksearchhelp
Copyright 1989-1997 © Cisco Systems Inc.