|
|
This document provides international regulatory and safety compliance information for the Cisco 806 router and the Cisco SOHO 71 router. Use this document with the following documents:
This document includes the following sections:
The following table lists the agency standards that apply to the router.
| Safety Standards | Emission and Immunity Standards |
|---|---|
IEC 60950:1992+A1+A2+A3+A4 | CISPR24, 1997 |
AS/NZS 3260 | CISPR22, Class B |
CAN/CSA 22.2 No. 950-95 | EN 55024:1998 |
GB 4943-95 | IEC 61000-4-2:1995 |
EN 60950: 1992, Amendment 4, 1997-10 (CENELEC; includes EU and EFTA) | IEC 61000-4-3:1995 |
NOM-019-SCFI-1998 | IEC 61000-4-4:1995 |
UL 1950 3rd Edition, 1995 | IEC 61000-4-5:1995 |
| IEC 61000-4-6:1996 |
| IEC 61000-4-11:1995 |
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment and the receiver
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Warning: Modification of this equipment without Cisco's authorization may result in this equipment no longer complying with FCC requirements for Class B digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television communications at your own expense.
Emissions:
This equipment complies with the requirements of CISPR 22 (EN 55022) for Class B Information Technology Equipment (ITE).
In addition to the warnings and safety guidelines listed in the "Translated Safety Warnings"section later in this document, the following operating condition applies to routers used in Canada:
The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational, and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements documents. The Department does not guarantee the equipment will operate to the user's satisfaction.
Before installing the equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable method of connection. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations.
Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions may give the telecommunications company cause to request the user to disconnect the equipment.
Users should ensure for your own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural areas.
Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or electrician, as appropriate.
Certified to US and Canadian requirements by the Canadian Standards Association.
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled "Digital Aparatus," ICES-003 of the Department of Communications.
Cet appareil numerique respecte les limites de bruits radioelectriques applicables aux appareils numeriques de Classe B prescrites dans la norme sur le materiel brouilleur: "Appareils Numeriques," NMB-003 edictee par le ministre des Communications.
Certified to Canadian requirements by Canadian Standards Association.
Network connected equipment is approved to the Australian and New Zealand Safety and EMC requirements by Cisco Systems Incorporated which is a Recognized Laboratory by ACA and New Zealand. Stand-alone power supply modules provided with this equipment are separately approved by an Australian State designated Electricity Authority.
This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual.
The warnings and safety guidelines listed in the "Translated Safety Warnings" section later in this document apply to routers used in the European Community.
In addition to the warnings and safety guidelines listed in the "Translated Safety Warnings" section later in this document, the following warnings apply to routers used in the United Kingdom:
This equipment carries the CE Mark and fulfills the essential requirements of all the applicable directives.
The Declaration of Conformity related to this product is located at the following URL:
http://www.cisco.com/cgi-bin/compliance/approvals_search.pl
This product bears the CE mark in conformance with Annex VII of Directive 1999/5/CE.
The following statements are warnings or safety guidelines. A warning means danger. You are in a situation that could cause bodily injury. Before working on equipment, be aware of the hazards involved with electrical circuitry and standard safety practices to prevent accidents.
| |||
Waarschuwing | Raadpleeg de installatie-aanwijzingen voordat u het systeem met de voeding verbindt. | ||
Varoitus | Lue asennusohjeet ennen järjestelmän yhdistämistä virtalähteeseen. | ||
Attention | Avant de brancher le système sur la source d'alimentation, consulter les directives d'installation. | ||
Warnung | Lesen Sie die Installationsanweisungen, bevor Sie das System an die Stromquelle anschließen. | ||
Avvertenza | Consultare le istruzioni di installazione prima di collegare il sistema all'alimentatore. | ||
Advarsel | Les installasjonsinstruksjonene før systemet kobles til strømkilden. | ||
Aviso | Leia as instruções de instalação antes de ligar o sistema à sua fonte de energia. | ||
¡Advertencia! | Ver las instrucciones de instalación antes de conectar el sistema a la red de alimentación. | ||
Varning! | Läs installationsanvisningarna innan du kopplar systemet till dess strömförsörjningsenhet. | ||
| |||
Waarschuwing | Voordat u aan een systeem werkt dat een aan/uit schakelaar heeft, dient u de stroomvoorziening UIT te schakelen en de stekker van het netsnoer uit het stopcontact te halen. | ||
Varoitus | Ennen kuin teet mitään sellaiselle järjestelmälle, jossa on kaksiasentokytkin, katkaise siitä virta ja kytke virtajohto irti. | ||
Attention | Avant de travailler sur un système équipé d'un commutateur marche-arrêt, mettre l'appareil à l'arrêt (OFF) et débrancher le cordon d'alimentation. | ||
Warnung | Bevor Sie an einem System mit Ein/Aus-Schalter arbeiten, schalten Sie das System AUS und ziehen das Netzkabel aus der Steckdose. | ||
Avvertenza | Prima di lavorare su un sistema dotato di un interruttore on/off, spegnere (OFF) il sistema e staccare il cavo dell'alimentazione. | ||
Advarsel | Slå AV strømmen og trekk ut strømledningen før det utføres arbeid på et system som er utstyrt med en av/på-bryter. | ||
Aviso | Antes de começar a trabalhar num sistema que tem um interruptor on/off, DESLIGUE a corrente eléctrica e retire o cabo de alimentação da tomada. | ||
¡Advertencia! | Antes de utilizar cualquier sistema equipado con interruptor de Encendido/Apagado (ON/OFF), cortar la alimentación y desenchufar el cable de alimentación. | ||
Varning! | Slå AV strömmen och dra ur nätsladden innan du utför arbete på ett system med strömbrytare. | ||
| |||
Waarschuwing | Dit product is afhankelijk van de in het gebouw gebruikte installatie voor kortsluit- (overstroom)beveiliging. Controleer of er een (UL-keurmerk) Listed en Certified zekering of stroomverbreker van niet meer dan 60 Volt gelijkstroom, 15 A gebruikt wordt op alle leidingen die stroom voeren. | ||
Varoitus | Tämä tuote on riippuvainen rakennukseen asennetusta oikosulkusuojauksesta (ylivirtasuojauksesta). Varmista, että kaikissa virroitetuissa johtimissa käytetään Yhdysvaltain UL-testilaboratorion luetteloimaa (Underwriters Laboratory Listed) ja sertifioitua korkeintaan 60 voltin tasavirralle ja 15 ampeerin jännitteelle sopivaa sulaketta tai suojakytkintä. | ||
Attention | Pour ce qui est de la protection contre les courts-circuits (surtension), ce produit dépend de l'installation du local. Vérifier qu'un fusible ou un disjoncteur homologué et classé UL de 60 V cc, 15 A maximum est utilisé sur les conducteurs de charge. | ||
Warnung | Dieses Produkt ist darauf angewiesen, daß im Gebäude ein Kurzschluß- bzw. Überstromschutz installiert ist. Stellen Sie sicher, daß eine Sicherung oder ein Unterbrecher (von der UL registriert und zertifiziert) von nicht mehr als 240 V Wechselstrom, 10 A (bzw. in den USA 120 V Wechselstrom, 15 A) an allen stromführenden Leitern verwendet wird. | ||
Avvertenza | La protezione di questo prodotto contro il cortocircuito (sovracorrente) dipende dall'impianto dell'edificio. Accertarsi che tutti i conduttori di fase siano protetti da fusibili o interruttori UL automatici di portata non superiore a 60 V c.c., 15 A. | ||
Advarsel | Dette produktet er avhengig av bygningens installasjoner av kortslutningsbeskyttelse (overstrøm). Kontroller at det brukes en registrert (av Underwriters Laboratory) og godkjent sikring eller strømbryter som ikke er større enn 60 VDC, 15 A på alle de strømførende lederne. | ||
Aviso | Este produto depende da instalação existente para obter protecção contra curto-circuito (sobrecarga). Certifique-se de que um fusível ou disjuntor listado e certificado (de acordo com os requisitos UL), não superior a 60 VAC, 15A, é utilizado em todos os condutores de transporte de corrente. | ||
¡Advertencia! | Este producto depende de la protección contra cortocircuitos (sobrecorrientes) de la instalación eléctrica del edificio. Asegurarse de que todos los conductores portadoresde corriente estén protegidos por un fusible o interruptor automático aprobado por Underwriters Laboratory (UL) y certificado por una agencia local de seguridad, y que tenga una capacidad no mayor de 60 voltios de corriente directa y 15 amperios. | ||
Varning! | Denna produkt är beroende av i byggnaden installerat kortslutningsskydd (överströmsskydd). Kontrollera att säkring eller överspänningsskydd som är "Listed" av Underwriters Laboratory samt certifierad för bruk med max. 60 V likström, 15 A används på samtliga strömförande ledare. | ||
| |||
Waarschuwing | Deze apparatuur hoort geaard te worden Zorg dat de host-computer tijdens normaal gebruik met aarde is verbonden. | ||
Varoitus | Tämä laitteisto on tarkoitettu maadoitettavaksi. Varmista, että isäntälaite on yhdistetty maahan normaalikäytön aikana. | ||
Attention | Cet équipement doit être relié à la terre. S'assurer que l'appareil hôte est relié à la terre lors de l'utilisation normale. | ||
Warnung | Dieses Gerät muß geerdet werden. Stellen Sie sicher, daß das Host-Gerät während des normalen Betriebs an Erde gelegt ist. | ||
Avvertenza | Questa apparecchiatura deve essere collegata a massa. Accertarsi che il dispositivo host sia collegato alla massa di terra durante il normale utilizzo. | ||
Advarsel | Dette utstyret skal jordes. Forviss deg om vertsterminalen er jordet ved normalt bruk. | ||
Aviso | Este equipamento deverá estar ligado à terra. Certifique-se que o host se encontra ligado à terra durante a sua utilização normal. | ||
¡Advertencia! | Este equipo debe conectarse a tierra. Asegurarse de que el equipo principal esté conectado a tierra durante el uso normal. | ||
Varning! | Denna utrustning är avsedd att jordas. Se till att värdenheten är jordad vid normal användning. | ||
| |||
Waarschuwing | Alvorens aan apparatuur te werken die met elektrische leidingen is verbonden, sieraden (inclusief ringen, kettingen en horloges) verwijderen. Metalen voorwerpen worden warm wanneer ze met stroom en aarde zijn verbonden, en kunnen ernstige brandwonden veroorzaken of het metalen voorwerp aan de aansluitklemmen lassen. | ||
Varoitus | Ennen kuin työskentelet voimavirtajohtoihin kytkettyjen laitteiden parissa, ota pois kaikki korut (sormukset, kaulakorut ja kellot mukaan lukien). Metalliesineet kuumenevat, kun ne ovat yhteydessä sähkövirran ja maan kanssa, ja ne voivat aiheuttaa vakavia palovammoja tai hitsata metalliesineet kiinni liitäntänapoihin. | ||
Attention | Avant d'accéder à cet équipement connecté aux lignes électriques, ôter tout bijou (anneaux, colliers et montres compris). Lorsqu'ils sont branchés à l'alimentation et reliés à la terre, les objets métalliques chauffent, ce qui peut provoquer des blessures graves ou souder l'objet métallique aux bornes. | ||
Warnung | Vor der Arbeit an Geräten, die an das Netz angeschlossen sind, jeglichen Schmuck (einschließlich Ringe, Ketten und Uhren) abnehmen. Metallgegenstände erhitzen sich, wenn sie an das Netz und die Erde angeschlossen werden, und können schwere Verbrennungen verursachen oder an die Anschlußklemmen angeschweißt werden. | ||
Avvertenza | Prima di intervenire su apparecchiature collegate alle linee di alimentazione, togliersi qualsiasi monile (inclusi anelli, collane, braccialetti ed orologi). Gli oggetti metallici si riscaldano quando sono collegati tra punti di alimentazione e massa: possono causare ustioni gravi oppure il metallo può saldarsi ai terminali. | ||
Advarsel | Fjern alle smykker (inkludert ringer, halskjeder og klokker) før du skal arbeide på utstyr som er koblet til kraftledninger. Metallgjenstander som er koblet til kraftledninger og jord blir svært varme og kan forårsake alvorlige brannskader eller smelte fast til polene. | ||
Aviso | Antes de trabalhar em equipamento que esteja ligado a linhas de corrente, retire todas as jóias que estiver a usar (incluindo anéis, fios e relógios). Os objectos metálicos aquecerão em contacto com a corrente e em contacto com a ligação à terra, podendo causar queimaduras graves ou ficarem soldados aos terminais. | ||
¡Advertencia! | Antes de operar sobre equipos conectados a líneas de alimentación, quitarse las joyas (incluidos anillos, collares y relojes). Los objetos de metal se calientan cuando se conectan a la alimentación y a tierra, lo que puede ocasionar quemaduras graves o que los objetos metálicos queden soldados a los bornes. | ||
Varning! | Tag av alla smycken (inklusive ringar, halsband och armbandsur) innan du arbetar på utrustning som är kopplad till kraftledningar. Metallobjekt hettas upp när de kopplas ihop med ström och jord och kan förorsaka allvarliga brännskador; metallobjekt kan också sammansvetsas med kontakterna. | ||
| |||
Waarschuwing | Om elektrische schokken te vermijden, mogen veiligheidscircuits met extra lage spanning (genaamd SELV = Safety Extra-Low Voltage) niet met telefoonnetwerkspanning (TNV) circuits verbonden worden. LAN (Lokaal netwerk) poorten bevatten SELV circuits en WAN (Regionaal netwerk) poorten bevatten TNV circuits. Sommige LAN en WAN poorten gebruiken allebei RJ-45 connectors. Ga voorzichtig te werk wanneer u kabels verbindt. | ||
Varoitus | Jotta vältyt sähköiskulta, älä kytke pienjännitteisiä SELV-suojapiirejä puhelinverkkojännitettä (TNV) käyttäviin virtapiireihin. LAN-portit sisältävät SELV-piirejä ja WAN-portit puhelinverkkojännitettä käyttäviä piirejä. Osa sekä LAN- että WAN-porteista käyttää RJ-45-liittimiä. Ole varovainen kytkiessäsi kaapeleita. | ||
Attention | Pour éviter une électrocution, ne raccordez pas les circuits de sécurité basse tension (Safety Extra-Low Voltage ou SELV) à des circuits de tension de réseau téléphonique (Telephone Network Voltage ou TNV). Les ports du réseau local (LAN) contiennent des circuits SELV et les ports du réseau longue distance (WAN) sont munis de circuits TNV. Certains ports LAN et WAN utilisent des connecteurs RJ-45. Raccordez les câbles en prenant toutes les précautions nécessaires. | ||
Warnung | Zur Vermeidung von Elektroschock die Sicherheits-Kleinspannungs-Stromkreise (SELV-Kreise) nicht an Fernsprechnetzspannungs-Stromkreise (TNV-Kreise) anschließen. LAN-Ports enthalten SELV-Kreise, und WAN-Ports enthalten TNV-Kreise. Einige LAN- und WAN-Ports verwenden auch RJ-45-Steckverbinder. Vorsicht beim Anschließen von Kabeln. | ||
Avvertenza | Per evitare scosse elettriche, non collegare circuiti di sicurezza a tensione molto bassa (SELV) ai circuiti a tensione di rete telefonica (TNV). Le porte LAN contengono circuiti SELV e le porte WAN contengono circuiti TNV. Alcune porte LAN e WAN fanno uso di connettori RJ-45. Fare attenzione quando si collegano cavi. | ||
Advarsel | Unngå å koble lavspenningskretser (SELV) til kretser for telenettspenning (TNV), slik at du unngår elektrisk støt. LAN-utganger inneholder SELV-kretser og WAN-utganger inneholder TNV-kretser. Det finnes både LAN-utganger og WAN-utganger som bruker RJ-45-kontakter. Vær forsiktig når du kobler kabler. | ||
Aviso | Para evitar choques eléctricos, não conecte os circuitos de segurança de baixa tensão (SELV) aos circuitos de tensão de rede telefónica (TNV). As portas LAN contêm circuitos SELV e as portas WAN contêm circuitos TNV. Algumas portas LAN e WAN usam conectores RJ-45. Tenha o devido cuidado ao conectar os cabos. | ||
¡Advertencia! | Para evitar la sacudida eléctrica, no conectar circuitos de seguridad de voltaje muy bajo (safety extra-low voltage = SELV) con circuitos de voltaje de red telefónica (telephone network voltage = TNV). Los puertos de redes de área local (local area network = LAN) contienen circuitos SELV, y los puertos de redes de área extendida (wide area network = WAN) contienen circuitos TNV. En algunos casos, tanto los puertos LAN como los WAN usan conectores RJ-45. Proceda con precaución al conectar los cables. | ||
Varning! | För att undvika elektriska stötar, koppla inte säkerhetskretsar med extra låg spänning (SELV-kretsar) till kretsar med telefonnätspänning (TNV-kretsar). LAN-portar innehåller SELV-kretsar och WAN-portar innehåller TNV-kretsar. Vissa LAN- och WAN-portar är försedda med RJ-45-kontakter. Iaktta försiktighet vid anslutning av kablar. | ||
| |||
Waarschuwing | De poorten die gelabeld zijn met "10BaseT," "100BaseTX" en "10/100" zijn veiligheidscircuits met extra-laag voltage (SELV). SELV-circuits mogen alleen op andere SELV-circuits worden aangesloten. Sluit deze circuits niet aan op telefoonnetwerkvoltage-circuits (TNV). | ||
Varoitus | Portit, joissa on merkintä "10BaseT", "100BaseTX" ja "10/100", ovat suojattuja erittäisen alhaisen jännitteen (SELV) piirejä. SELV-piirit tulisi liittää ainoastaan toisiin SELV-piireihin. Vältä kytkemästä näitä piirejä puhelinverkkojännitteen (TNV) piireihin. | ||
Attention | Les ports « 10BaseT », « 100BaseTX » et « 10/100 » sont des circuits SELV (très basse tension de sécurité). Ils doivent être connectés uniquement à d'autres circuits SELV. Il est recommandé de ne pas les connecter à des circuits de réseau téléphonique (tension TNV). | ||
Warnung | Warnung: Die Ports mit der Bezeichnung "10BaseT", 100BaseTX" und "10/100" sind sogenannte SELV-Schaltungen, Sicherheitsschaltungen mit extra-niedriger Spannung. SELV-Schaltungen sollten nur an andere SELV-Schaltungen angeschlossen werden. Sie dürfen nicht an TNV-Schaltungen, Schaltungen mit Telefonnetzspannung, angeschlossen werden. | ||
Avvertenza | Le porte designate "10BaseT", 100BaseTX", e "10/100" sono circuiti con un voltaggio di sicurezza molto basso (SELV). I circuiti SELV dovrebbero essere connessi unicamente ad altri circuiti SELV. Evitate di connettere questi circuiti a quelli con voltaggio di rete telefonica (TNV). | ||
Advarsel! | Utgangene merket "10BaseT", "00BaseTX" og "10/100" er sikkerhetskretser med veldig lav spenning (SELV). SELV-kretser skal bare kobles til andre SELV-kretser. Unngå å koble disse kretsene til kretser for telefonnettspenning (TNV). | ||
Aviso | As portas "10BaseT", "100BaseTX", e "10/100" são circuitos de segurança de baixa tensão (SELV). Estes circuitos SELV deverão ser ligados apenas a outros circuitos SELV. Evitar ligar estes circuitos aos circuitos (TNV) de tensão de rede telefónica. | ||
¡Advertencia! | Los puertos llamados "10BaseT", "100BaseTX" y "10/100" son circuitos de seguridad de voltaje muy bajo (Safety Extra-low Voltage, SELV). Estos circuitos sólo deben conectarse a otros circuitos SELV. Evite conectar estos circuitos a circuitos de voltaje de la red telefónica. | ||
Varning! | Portarna med beteckningen "10BaseT", "100BaseTX" och "10/100" är SELV-kretsar (skyddskretsar för mycket låg spänning). SELV-kretsar ska endast kopplas till andra SELV-kretsar. Undvik att koppla dessa kretsar till kretsar med telefonnätsspänning (TNV). | ||
 |
Caution No operator serviceable parts inside. Refer servicing to qualified personnel. |
The following sections provide sources for obtaining documentation from Cisco Systems.
You can access the most current Cisco documentation on the World Wide Web at the following sites:
Cisco documentation and additional literature are available in a CD-ROM package, which ships with your product. The Documentation CD-ROM is updated monthly and may be more current than printed documentation. The CD-ROM package is available as a single unit or as an annual subscription.
Cisco documentation is available in the following ways:
If you are reading Cisco product documentation on the World Wide Web, you can submit technical comments electronically. Click Feedback in the toolbar and select Documentation. After you complete the form, click Submit to send it to Cisco.
You can e-mail your comments to bug-doc@cisco.com.
To submit your comments by mail, use the response card behind the front cover of your document, or write to the following address:
Attn Document Resource Connection
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-9883
We appreciate your comments.
Cisco provides Cisco.com as a starting point for all technical assistance. Customers and partners can obtain documentation, troubleshooting tips, and sample configurations from online tools. For Cisco.com registered users, additional troubleshooting tools are available from the TAC website.
Cisco.com is the foundation of a suite of interactive, networked services that provides immediate, open access to Cisco information and resources at anytime, from anywhere in the world. This highly integrated Internet application is a powerful, easy-to-use tool for doing business with Cisco.
Cisco.com provides a broad range of features and services to help customers and partners streamline business processes and improve productivity. Through Cisco.com, you can find information about Cisco and our networking solutions, services, and programs. In addition, you can resolve technical issues with online technical support, download and test software packages, and order Cisco learning materials and merchandise. Valuable online skill assessment, training, and certification programs are also available.
Customers and partners can self-register on Cisco.com to obtain additional personalized information and services. Registered users can order products, check on the status of an order, access technical support, and view benefits specific to their relationships with Cisco.
To access Cisco.com, go to the following website:
The Cisco TAC website is available to all customers who need technical assistance with a Cisco product or technology that is under warranty or covered by a maintenance contract.
If you have a priority level 3 (P3) or priority level 4 (P4) problem, contact TAC by going to the TAC website:
P3 and P4 level problems are defined as follows:
In each of the above cases, use the Cisco TAC website to quickly find answers to your questions.
To register for Cisco.com, go to the following website:
http://www.cisco.com/register/
If you cannot resolve your technical issue by using the TAC online resources, Cisco.com registered users can open a case online by using the TAC Case Open tool at the following website:
http://www.cisco.com/tac/caseopen
If you have a priority level 1 (P1) or priority level 2 (P2) problem, contact TAC by telephone and immediately open a case. To obtain a directory of toll-free numbers for your country, go to the following website:
http://www.cisco.com/warp/public/687/Directory/DirTAC.shtm l
P1 and P2 level problems are defined as follows:
This document is to be used in conjunction with the documents listed on page 1 of this document.
Copyright © 2002, Cisco Systems, Inc.
All rights reserved.
Posted: Sun Feb 3 00:32:54 PST 2002
All contents are Copyright © 1992--2002 Cisco Systems, Inc. All rights reserved.
Important Notices and Privacy Statement.
