cc/td/doc/product/access/200
hometocprevnextglossaryfeedbacksearchhelp
PDF

Table of Contents

Cisco 200 System Messages

Cisco 200 System Messages

This appendix contains system or error messages that might display when you are using the Cisco 200. Most of these messages are generated by the ISDN exchange or PABX and indicate errors during initialization and connection establishment.


Note See the section "Physical Connection Messages" in this appendix for a list of messages generated by the ISDN carrier.

For information about obtaining technical assistance with your Cisco 200 product, refer to the Cisco Information Packet, which shipped with your product.

Software Messages

This section lists the most common Cisco 200 software errors, their causes, and recommended solutions; however, if other error messages are displayed, refer to your Cisco Information Packet for information on obtaining technical assistance.

The messages are listed in alphabetical order.

Error Message    Accepted MSN contains invalid characters

Explanation    The parameter ACCEPTED MSN in the ISDN200.CFG file contains invalid characters.

Recommended Action    Remove the invalid characters. The following lines are valid:

ACCEPTED MSN = *
ACCEPTED MSN =
digit sequence

Error Message    Another application got that call

Explanation    The Cisco 200 (CISCO200.EXE) tried to accept an incoming call, but another application in the same PC was faster and took the call.

Recommended Action    Remove the other application from memory.

Error Message   

Application registration failed; code = code

LISTEN_REQ results in error; code = code

GET_MESSAGE results in error; code = code

Did not get LISTEN_CONF message

LISTEN_CONF contains error; code = code

Installation of Signalling function failed; code = code

Explanation    Communication between ISDN200 and CAPI200 failed during initialization.

Recommended Action    Unload all drivers, especially CAPI200, then reload them. If the error still occurs, try replacing the ISDN Adapter.

Error Message    Authentication failed - password rejected by remote system

Explanation    This system sent an incorrect password to the connecting router.

Recommended Action    Ensure that the system name in the ISDN200.CFG file and the password specified in the router's section are configured correctly. Check these items on the connecting router as well.

Error Message    Authentication failed - remote not configured

Explanation    The connecting router is not configured for the Challenge Handshake Authentication Protocol (CHAP).

Recommended Action    Either comment out the line "PASSWORD = ..." in the ISDN200.CFG file (by placing a semicolon [;] as the first character) or reconfigure the connecting router to use CHAP.

Error Message    Authentication failed - remote sent incorrect password

Explanation    The connecting router sent an incorrect CHAP password.

Recommended Action    Ensure that the password for this connection is set up correctly on the connecting router. Ensure that the local name is correct and the password is specified in the "Routers" section. Ensure that the passwords match exactly; passwords are case-sensitive.

Error Message    Bearer service not implemented

Explanation    Data transfer with 64 kbps service is not available for your terminal or the destination terminal.

Recommended Action    Ask your ISDN carrier or PABX representative if this service is enabled for your ISDN terminal and for your connecting router. Check the telephone number that is displayed when calling ISDN200.

Error Message    Call rejected

Explanation    Your call was rejected by the connecting router.

Recommended Action    Ensure that your phone number is in the list of acceptable numbers on the connecting router. Check the communications at the connecting router. Some systems reject incoming calls when the origination phone number indicated by the network does not match a specified number. Ensure that the phone number equivalent on the connecting router is set up correctly.

This message can also appear if there is a dialing contention; that is, the connecting router and local system try to call at the same time. The Cisco 200 driver will wait for three seconds (the default) between dialing attempts. You can change this value to avoid contention situations by adding the following line to the "Local" section of the ISDN200.CFG file:

PAUSE BETWEEN RETRIES = seconds Error Message    Cause normal

Explanation    The public exchange or your private branch exchange does not give a reason why the ISDN connection was not established. The connection may have been disabled by the exchange station.

Recommended Action    Try to establish the connection again. If this message recurs, ask an engineer to reset the connection to your PABX. If you have a public ISDN interface, ask your ISDN carrier to check your connection.

Error Message    COMMON ISDN API not found

Explanation    The Cisco 200 program could not find the CAPI200 file during startup.

Recommended Action    Ensure that the CAPI200 file is present and in your PC's path before starting Cisco 200.

Error Message    connection establishment to router failed

Explanation    This message is usually preceded by three D-channel error messages (causes).

Recommended Action    Try the solutions listed by the error messages. If that does not resolve the situation, check the following items:

Error Message    connection establishment to router failed

Explanation    The connection was not established because the maximum time allowed for the establishment of the logical connection was exceeded. You may have established a connection to an unknown ISDN system. The Cisco 200 can communicate only with Cisco Systems or other PPP-compliant ISDN routers.

Recommended Action    Check with your system administrator to ensure that the connecting router you are trying to access is a PPP-compliant ISDN router.

Error Message    connection rejected by router - cause: rejection reason

Explanation    A physical connection to the connecting router was established but during the negotiation procedure your call was rejected. This error may also occur if you try to establish a connection with a non-PPP-compliant router.

Recommended Action    Ensure that your workstation is on the list of acceptable numbers on the connecting router.

Error Message    connection with router cannot be reactivated in current state x connection with router cannot be put to sleep in current state x

Explanation    The current connection is in an intermediate state; that is, "going up," "identifying," or "going down." The requested action cannot be invoked during these states.

Recommended Action    Wait for the state to change to "activated," "sleeping," or "released" and make the request again.

Error Message    Country code is missing in dialnumber number Area code is missing in dialnumber number Local code is missing in dialnumber number Inhouse code is missing in dialnumber number In specified dialnumber number

Explanation    The router's DIALNUMBER specified in the ISDN200.CFG file has a syntax error.

Recommended Action    Specify the DIALNUMBER in one of two ways:


  1. Use a dot as the first character and append directly all digits to dial. This string must not contain any characters other than digits. For example:
DIALNUMBER = .5553333

  1. Specify the DIALNUMBER as a three, four, or seven-part number. All parts are separated by a hyphen. A three-part or seven-part number means that the connecting router is connected to a public ISDN line; a four-part number means a connection to a PABX. The parts themselves must contain only digits. For example:
DIALNUMBER = 1-408-555-3333 or DIALNUMBER = 49-239-5553333 Error Message    destination not obtainable

Explanation    The ISDN connection could not be established because the destination address dialed is not valid.

Recommended Action    Check the dialnumber of the connecting router in the ISDN200.CFG file and repeat the call. The number dialed will be displayed when calling ISDN200.

Error Message    Destination out of order

Explanation    The connecting router is not operating.

Recommended Action    Ensure that the connecting router is operating and try again.

Error Message    Entry 'NAME' for own configuration is missing in file

Explanation    There is no name entered for your station in your ISDN200.CFG file.

Recommended Action    Edit the ISDN200.CFG file and add a name to the NAME= line. For example:

NAME = MyHomeOffice Error Message    Error establishing D channel Layer 1 - Cable may be broken

Explanation    A connection from your ISDN adapter to the ISDN switch could not be established.

Recommended Action    Ensure that the cables to and from the NT1 and the ISDN Adapter are firmly connected and operating properly. Ensure that the ISDN connection to the exchange is operating properly.

Error Message    Error establishing D channel Layer 2

Explanation    A D-channel layer 2 connection from your ISDN card to the ISDN switch could not be established.

Recommended Action    Ensure that the ISDN line is configured correctly and that the line is configured as a multipoint line with TEI negotiation.

Error Message    Error establishing D channel Layer 3 - possibly wrong protocol

Explanation    A D-channel layer 3 connection from your ISDN Adapter to the ISDN switch could not be established. This usually occurs if the wrong D-channel protocol has been selected.

Recommended Action    Ensure that you started CAPI200 with the correct protocol specification parameter (p number). On NI1 and 5ESS lines, ensure that the SPID and directory numbers are specified correctly.

Error Message    Inconsistent line found

Explanation    A line in the ISDN200.CFG file contains an error. The applicable line is displayed after the message.

Recommended Action    Edit the ISDN200.CFG file to fix the line.

Error Message    INDICATED DIALNUMBER of router contains invalid characters

Explanation    The parameter INDICATED DIALNUMBER in the "Router" section contains invalid characters.

Recommended Action    Remove the invalid characters from that line. The following lines are valid:

INDICATED DIALNUMBER = IGNORE INDICATED DIALNUMBER = string of digits Error Message    Cisco 200 driver not found at interrupt xxxx Cisco 200 driver not found

Explanation    The CISCO200.EXE file is not present at the interrupt indicated.

Recommended Action    Check the jumpers on the ISDN Adapter. Make sure they are configured for the correct interrupt. Refer to the Cisco 200 ISDN Adapter Hardware Installation and Configuration Guide.

Error Message    keyword too long - cut after first n characters

Explanation    The ISDN200.CFG file contains a line that has an argument with too many characters. The argument string is truncated after the given number of characters.

Recommended Action    Edit the ISDN200.CFG file to reduce the number of characters.

Error Message    CISCO200 found at interrupt xxxx ISDN200.EXE found

Explanation    ISDN200 could not find either the Cisco 200 or a packet driver in the system's main memory.

Recommended Action    Start the Cisco 200 before calling ISDN200.

Error Message    Line 'INDICATED DIALNUMBER = number' must not be used
concurrently with line 'INDICATED DIALNUMBER = IGNORE'
Line 'INDICATED DIALNUMBER = IGNORE' must not be used
concurrently with line 'INDICATED DIALNUMBER = number

Explanation    You specified one or multiple indicated dialnumbers and at the same time turned off the dialnumber check.

Recommended Action    Remove the following line:

INDICATED DIALNUMBER = IGNORE

or all lines of the following form:

INDICATED DIALNUMBER = string of digits

from the router's record. For temporary attempts, you can comment out these lines by inserting a semicolon [;] in the first row of the line.

Error Message    Network congestion

Explanation    There is congestion on the ISDN network.

Recommended Action    Try to establish a connection again. If the error message recurs, contact your ISDN carrier.

Error Message    Network out of order

Explanation    The ISDN network is currently not operating properly.

Recommended Action    Try to establish a connection again. If the error recurs, contact your ISDN carrier.

Error Message    No route to specified No route to destination

Explanation    The ISDN connection could not be established because the destination address dialed is not valid.

Recommended Action    Check the dialnumber of the respective connecting router in the ISDN200.CFG file and repeat the action. The number dialed will be displayed when calling ISDN200.

Error Message    No user responding

Explanation    The connecting router is not responding.

Recommended Action    Ensure that the connecting router is on, or test the dialnumber of the connecting router. Ensure that the connecting router is configured correctly to accept the incoming call.

Error Message    NODE ADDRESS is setable via NET.CFG only

Explanation    The ISDN200.CFG file contains a line with the keyword "NODE ADDRESS."

Recommended Action    Remove the line from the ISDN200.CFG file. Edit your NET.CFG file instead and specify the following line in the "Link Driver Cisco 200" section:

NODE ADDRESS = hexadecimal digits Error Message    NODE ADDRESS is 0 - setup entry 'NODE ADDRESS' in file NET.CFG

Explanation    The NET.CFG file does not contain a specification of a NODE ADDRESS for the Cisco 200 driver.

Recommended Action    Add the following line to the "Link Driver Cisco 200" section of the NET.CFG file:

NODE ADDRESS = address

Ensure that the node address is unique within the entire network.

Error Message    NODE ADDRESS is 0 - setup entry 'NODE ADDRESS' in file NET.CFG NODE ADDRESS is 0 - change entry 'NODE ADDRESS' in file

Explanation    These messages are most likely caused by one of the following:


  1. Your ISDN Adapter is not supplying a serial number, and the driver's Ethernet address (NODE ADDRESS) is 0, which is not permitted.

  2. Cisco 200 cannot find the correct NET.CFG file.

Recommended Action    The solutions to these problems are as follows:


  1. Add the NODE ADDRESS line to the NET.CFG file in the "Cisco 200" section. If you are using the packet driver, add the following line for your own configuration in the ISDN200.CFG file:
NODE ADDRESS = value

  1. Make sure that the AUTOEXEC.BAT file correctly calls the directory location of the CONNECT.BAT file.
Error Message    Normal call clearing

Explanation    This message indicates that an attempt was made to contact the connecting router. If the attempt is successful, no further messages will appear. If the attempt is unsuccessful, a more specific message might follow.

Recommended Action    If no messages follow this one, you need take no action; the Cisco 200 has successfully contacted the connecting router. If other messages follow this one, refer to their explanations and recommended actions elsewhere in this appendix.

Error Message    number changed

Explanation    The phone number of the connecting router has changed.

Recommended Action    Ask your network administrator for the new phone number and change the phone number in the ISDN200.CFG file.

Error Message    Old Section [ALL] is not allowed anymore

Explanation    The ISDN200.CFG file contains an [ALL] section. No router section can be named [ALL].

Recommended Action    Change the section name to another name.

Error Message    Only one of the parameters -s, -d, -c, -a and -r may be given

Explanation    You cannot use more than one parameter switch at a time.

Recommended Action    Use only one of the displayed parameter switches at a time.

Error Message    out of order

Explanation    The connecting router is not operational.

Recommended Action    Repeat the action. If the error continues to appear, check the operation of the connecting router.

Error Message    Own configured DIALNUMBER too long DIALNUMBER of partner name too long INDICATED DIALNUMBER of router too long - cut after n chars

Explanation    The INDICATED DIALNUMBER line in the ISDN200.CFG file contains a syntax error in the keyword string.

Recommended Action    Reduce the number of characters in the keyword string. Retry running CONNECT.BAT.

Error Message    Parameter CHANNELS is not allowed for PPP connections

Explanation    The CHANNELS parameter is specified in the ISDN200.CFG file; however, channel bundling is not yet available with PPP.

Recommended Action    Remove the CHANNELS statement from the ISDN200.CFG file.

Error Message    Parameter file does not contain entry for
partner name

Explanation    The router name specified in the command line of the ISDN200.EXE program must match the partner name in the "Routers" section of the ISDN200.CFG file.

Recommended Action    Compare the router name in the ISDN200.CFG file with the router name on the command line.

Error Message    ISDN200.CFG file not found An error occurred reading the file

Explanation    Either the ISDN200.EXE program could not find the ISDN200.CFG file or an error occurred when the ISDN200.CFG file was read.

Recommended Action    Ensure that the ISDN200.CFG file is in the directory in which you installed the Cisco 200 software. If the file is missing, use an ASCII text editor to generate the ISDN200.CFG file as described in the appendix "Modifying the Cisco 200 Configuration Files" or reinstall the Cisco 200 software.

Error Message    file not found

Explanation    The ISDN200 program could not find the ISDN200.CFG file. Ensure that the ISDN200.CFG file is in the directory in which you installed the Cisco 200 software.

Recommended Action    If the file is missing, use an ASCII text editor to generate the ISDN200.CFG file.

Error Message    Parameter -i has got invalid argument

Explanation    The interrupt switch -i was specified with an invalid argument, for example, an incorrect interrupt number.

Recommended Action    Use -i with a hexadecimal argument (for example, -i 0x63) or a decimal argument (for example, -i 94). Be sure you leave a space between the -i and the argument.

Error Message    Parameter SERVICE has invalid argument

Explanation    The SERVICE parameter specified in the ISDN200.CFG file has an invalid argument.

Recommended Action    Change the argument to a valid entry. Valid arguments are DATA64 (default) and DATA56.

Error Message    physical connection established Timeout - connection establishment to router failed

or

physical connection established logical connection establishment failed - welcome procedure error

Explanation    If either message sequence displays, the maximum time allowed for the logical connection establishment has been exceeded and the connection has failed. However, the physical ISDN connection (the D channel) was established and is working properly.

Recommended Action    Follow these steps to correct this situation:

Error Message    remote procedure error

Explanation    The connection was disabled by the ISDN exchange due to an undefined problem in the local node.

Recommended Action    Try to establish a connection again.

Error Message    Remote Router name is needed to initialize Cisco 200

Explanation    You must specify the name of the connecting router when starting the Cisco 200.

Recommended Action    Enter the following:

CONNECT routername

or include the following statement in your initialization script:

ISDN200 routername Error Message    Router name is needed to initialize Cisco 200

Explanation    ISDN200 was started for the first time without additional parameters after loading the Cisco 200 software.

Recommended Action    When running ISDN200 for the first time, specify the name of the connecting router. On subsequent calls, the current driver configuration will be displayed.

Error Message    service not available requested fac. not subscr

Explanation    Data transfer with 64 kbps service is not applied to your terminal or the destination terminal.

Recommended Action    Ask your ISDN carrier or the representative of your PABX if this service is enabled for your ISDN terminal and for your connecting router. Check the selected dialnumber that is displayed when running CONNECT.BAT.

Error Message    The LSL is not loaded

Explanation    The network manager link support layer (LSL) could not be found in the PC's memory.

Recommended Action    Check the CONNECT.BAT file to ensure that LSL is loaded before the Cisco 200 software is installed.

Error Message    Timeout - connection establishment to router failed

Explanation    The establishment of a physical ISDN connection failed because the maximum time allowed for the physical connection establishment was exceeded. This is similar to a "ringing telephone" situation. The destination you tried to contact sent an alert to its switch indicating that it will take some time until the call will be accepted or rejected. An alert can take up to three minutes in an ISDN network.

Recommended Action    Verify that the connecting router receives a call. Switch on Q.931 or D-channel layer 3 debug facilities to check for incoming setup messages. If the setup message is received, the connecting router is configured incorrectly and will not accept the call. If the call is not received, the network is not delivering the call. In that case, perform standard physical connection checks.

Error Message    Timeout - connection with router won't sleep

Explanation    You tried to place the ISDN connection in a sleep state by executing ISDN200 -s. The line did not go to sleep because there is still valid traffic on the line, which reestablished the connection.

Recommended Action    Wait until there is no longer any traffic on the line and try using the ISDN -s command again.

Error Message    Timeout - release of connection with router is still pending - unload driver

Explanation    The connection could not be released when you executed ISDN200 -d. This can occur due to a malfunction of the ISDN switch or of CAPI200.EXE.

Recommended Action    Unload all drivers, including CAPI200.EXE.

Error Message    To establish a connection with router the current partner has to be released first - use 'ISDN200 -d'

Explanation    Only one connection can be used at a time. Before you can start a connection to the specified router, you must release the currently active router.

Recommended Action    Release the currently active router either by entering: DCONNECT.BAT or by executing ISDN200 -d.

Error Message    Too many INDICATED DIALNUMBERs specified for partner name

Explanation    Too many lines with the parameter INDICATED DIALNUMBER are specified in the "Routers" section of the ISDN200.CFG file. A maximum of 16 INDICATED DIALNUMBER lines per router are allowed.

Recommended Action    Reduce the number of lines accordingly.

Error Message    Unallocated number Normal call clearing

Explanation    On NI1 and 5ESS lines, these causes are typical for SPID and directory number configuration problems on the local side.

Recommended Action    Ensure that you specified the correct SPID and directory number for your ISDN line. Both values must be given as parameters loading CAPI200.

Error Message    User busy

Explanation    The connecting router is busy.

Recommended Action    Ensure that the connecting router is activated and that at least one B channel is available for data communication.

Error Message    Version of ISDN200 does not match Cisco 200 version

Explanation    You must use ISDN200 and Cisco 200 files from the same Cisco 200 software version. Reinstall the newest version of Cisco 200 software.

Physical Connection Messages

This section lists messages that might be generated by the ISDN carrier. Troubleshooting questions for these messages should be directed to the ISDN carrier (telephone company).

Error Message    Access info discarded Bearer cap. not authorized Bearer cap. not impl B.cap. not pres. avail Call delivered in estab. ch Call identity in use Call rejected Call (requ.call id) cleared Channel type not impl Channel unacceptable Destination out of order Facility rejected Identified chan.not exist Incompatible destination Inv. transit network selec Invalid crn value Invalid informationelem Invalid message Invalid number format Mandatory infoelem. miss Message not compatible in call state Message type not impl/exs Network out of order No answer from alerted user No call suspended No channel available No route to destination No route to specified No user responding Non-selected user clearing Normal call clearing Normal, unspecified Number changed Only rest.dig.info.b.cap Protocol error, unspec Qual.of service unavail Recovery on timer expiry Request fac. not subscr Requested chan. not avail Requested fac. not impl Resources unavailable Response to STATUS ENQUIRY Service not available Service not implemented Susp.call ex.,bad call id Switching equip. congest Temporary failure Unallocated number Unknown informationelement User busy

Explanation    Error messages preceded with "0x34," such as the messages above, are generated when a physical connection cannot be established.

Recommended Action    Ensure that the ISDN Adapter is properly installed and connected. If it is, contact your ISDN provider and ask to have the physical connection checked.

hometocprevnextglossaryfeedbacksearchhelp
Copyright 1989-1997 © Cisco Systems Inc.