Network Working Group B. Ray
Request for Comments: 3276 PESA Switching Systems
Category: Standards Track R. Abbi
Alcatel
May 2002
Definitions of Managed Objects for High Bit-Rate DSL - 2nd generation
(HDSL2) and Single-Pair High-Speed Digital Subscriber
Line (SHDSL) Lines
Status of this Memo
This document specifies an Internet standards track protocol for the
Internet community, and requests discussion and suggestions for
improvements. Please refer to the current edition of the "Internet
Official Protocol Standards" (STD 1) for the standardization state
and status of this protocol. Distribution of this memo is unlimited.
Copyright Notice
Copyright (C) The Internet Society (2002). All Rights Reserved.
Abstract
This document defines a portion of the Management Information Base
(MIB) module for use with network management protocols in the
Internet community. In particular, it describes objects used for
managing High Bit-Rate DSL - 2nd generation (HDSL2) and Single-Pair
High-Speed Digital Subscriber Line (SHDSL) interfaces.
Table of Contents
1. Introduction ............................................. 22. The SNMP Network Management Framework .................... 23. Introduction ............................................. 33.1 Relationship of the HDSL2/SHDSL Line MIB to other MIBs ... 3
3.2 IANA Considerations ...................................... 54. Conventions used in the MIB .............................. 54.1 Naming Conventions ....................................... 54.2 Textual Conventions ...................................... 64.3 Structure ................................................ 74.4 Counters, Interval Buckets and Thresholds ................ 104.5 Profiles ................................................. 114.6 Notifications ............................................ 125. Conformance and Compliance ............................... 146. Definitions .............................................. 147. Security Considerations .................................. 60
Ray & Abbi Standards Track [Page 1]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
8. Acknowledgments .......................................... 629. References ............................................... 6310. Intellectual Property Notice ............................. 6511. Authors' Addresses ....................................... 6512. Full Copyright Statement ................................. 66
This document defines a portion of the Management Information Base
(MIB) module for use with network management protocols in the
Internet community. In particular, it describes objects used for
managing High Bit-Rate DSL - 2nd generation (HDSL2) [18] and Single-
Pair High-Speed Digital Subscriber Line (SHDSL) interfaces [19].
The SNMP Management Framework presently consists of five major
components:
o An overall architecture, described in RFC 2571 [1].
o Mechanisms for describing and naming objects and events for the
purpose of management. The first version of this Structure of
Management Information (SMI) is called SMIv1 and is described in
STD 16, RFC 1155 [2], STD 16, RFC 1212 [3], and RFC 1215 [4]. The
second version, called SMIv2, is described in STD 58, RFC 2578
[5], RFC 2579 [6], and RFC 2580 [7].
o Message protocols for transferring management information. The
first version of the SNMP message protocol is called SNMPv1 and is
described in STD 15, RFC 1157 [8]. A second version of the SNMP
message protocol, which is not an Internet standards track
protocol, is called SNMPv2c and described is in RFC 1901 [9] and
RFC 1906 [10]. The third version of the message protocol is
called SNMPv3 and is described in RFC 1906 [10], RFC 2572 [11],
and RFC 2574 [12].
o Protocol operations for accessing management information. The
first set of protocol operations and associated PDU formats is
described in STD 15, RFC 1157 [8]. A second set of protocol
operations and associated PDU formats is described in RFC 1905
[13].
o A set of fundamental applications described in RFC 2573 [14] and
the view-based access control mechanism described in RFC 2575
[15].
Ray & Abbi Standards Track [Page 2]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
A more detailed introduction to the current SNMP Management Framework
can be found in RFC 2570 [16].
Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. Objects in the MIB are
defined using the mechanisms defined in the SMI.
This memo specifies a MIB module that is compliant to the SMIv2. A
MIB conforming to the SMIv1 can be produced through the appropriate
translations. The resulting translated MIB must be semantically
equivalent, except where objects or events are omitted because no
translation is possible (use of Counter64). Some machine readable
information in SMIv2 will be converted into textual descriptions in
SMIv1 during the translation process. However, this loss of machine
readable information is not considered to change the semantics of the
MIB.
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [17].
This document describes an SNMP MIB for managing HDSL2/SHDSL Lines.
These definitions are based upon the specifications for the HDSL2 and
SHDSL Embedded Operations Channel (EOC) as defined in ANSI
T1E1.4/2000-006 [18] and ITU G.991.2 [19].
The MIB is located in the MIB tree under MIB 2 transmission, as
discussed in the MIB-2 Integration (RFC 1213 [20] and RFC 2863 [21])
section of this document.
The HDSL2/SHDSL Line MIB specifies the detailed attributes of a data
interface. As such, it needs to integrate with RFC 2863 [21]. The
IANA has assigned the following ifTypes to HDSL2 and SHDSL:
Ray & Abbi Standards Track [Page 3]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
IANAifType ::= TEXTUAL-CONVENTION
...
SYNTAX INTEGER {
...
hdsl2 (168), -- High Bit-Rate DSL, 2nd generation
shdsl (169), -- Multirate HDSL2
...
}
Note that the ifFixedLengthGroup from RFC 2863 [21] MUST be supported
and that the ifRcvAddressGroup does not apply to this MIB.
The MIB branch identified by this ifType contains tables appropriate
for this interface type. Most such tables extend the ifEntry table,
and are indexed by ifIndex. For interfaces in systems implementing
this MIB, those table entries indexed by ifIndex MUST be persistent.
The following attributes are part of the mandatory ifGeneral group in
RFC 2863 [21], and are not duplicated in the HDSL2/SHDSL Line MIB.
Ray & Abbi Standards Track [Page 4]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
===================================================================
ifIndex Interface index.
ifDescr See interfaces MIB [21].
ifType hdsl2(168) or shdsl(169).
ifSpeed Set as appropriate.
(This is fixed at 1552000 for HDSL2
lines)
ifPhysAddress This object MUST have an octet string
with zero length.
ifAdminStatus See interfaces MIB [21].
ifOperStatus See interfaces MIB [21].
ifLastChange See interfaces MIB [21].
ifName See interfaces MIB [21].
ifLinkUpDownTrapEnable Default to enabled(1).
ifHighSpeed Set as appropriate.
(For HDSL2 lines, this is fixed at 2)
ifConnectorPresent Set as appropriate.
===================================================================
Figure 1: Use of ifTable Objects
The HDSL2-SHDSL-LINE-MIB module requires the allocation of a single
object identifier for its MODULE-IDENTITY. The IANA has allocated
this object identifier in the transmission subtree (48), defined in
the SNMPv2-SMI MIB module.
A. xtuC refers to a central site terminal unit;
H2TU-C for HDSL2, or STU-C for SHDSL.
B. xtuR refers to a remote site terminal unit;
H2TU-R for HDSL2, or STU-R for SHDSL.
C. xtu refers to a terminal unit; either an xtuC or xtuR.
Ray & Abbi Standards Track [Page 5]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
D. xru refer to a regenerator unit;
H2RU for HDSL2, or SRU for SHDSL.
E. xU refers to any HDSL2/SHDSL unit; either an xtu or xru.
F. CRC is cyclic redundancy check [19].
G. ES means errored second [19].
H. LOSW means loss of sync word [19].
I. LOSWS means LOSW seconds [19].
J. SES means severely errored second [19].
K. SNR means signal-to-noise ratio [19].
L. UAS means unavailable second [19].
The following textual conventions are defined to reflect the line
topology in the MIB (further discussed in the following section) and
to define the behavior of the statistics to be maintained by an
agent.
o Hdsl2ShdslUnitId:
Attributes with this syntax uniquely identify each unit in a
HDSL2/SHDSL span. It mirrors the EOC addressing mechanism:
xtuC(1) - CO terminal unit
xtuR(2) - CPE terminal unit
xru1(3) .. xru8(10) - regenerators, numbered from
central office side
o Hdsl2ShdslUnitSide:
Attributes with this syntax reference the two sides of a unit:
networkSide(1) - N in figure 2, below
customerSide(2) - C in figure 2, below
o Hdsl2ShdslWirePair:
Attributes with this syntax reference the wire-pairs connecting the
units:
wirePair1(1) - First pair for HDSL2/SHDSL.
wirePair2(2) - Optional second pair for SHDSL only.
o Hdsl2ShdslTransmissionModeType:
Attributes with this syntax specify the regional setting for a SHDSL
line. Specified as a BITS construct, the two mode types are:
Ray & Abbi Standards Track [Page 6]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
region1 - ITU-T G.991.2 Annex A
region2 - ITU-T G.991.2 Annex B
o Hdsl2ShdslPerfCurrDayCount:
Attributes with this syntax define the behavior of the 1-day (24
hour) gauges found in the MIB.
o Hdsl2Shdsl1DayIntervalCount:
Attributes with this syntax define the behavior of the 1-day (24
hour) interval counters found in the MIB.
o Hdsl2ShdslPerfTimeElapsed:
Attributes with this syntax define the behavior of the elapsed time
counters found in the MIB.
o Hdsl2ShdslPerfIntervalThreshold:
Attributes with this syntax define the behavior of the alarm
thresholds found in the MIB.
o Hdsl2ShdslClockReferenceType
Attributes with this syntax define the clock references for the
HDSL2/SHDSL span.
The MIB is structured into following MIB groups:
o Span Configuration Group:
This group supports MIB objects for configuring parameters for the
HDSL2/SHDSL span. It contains the following table:
- hdsl2ShdslSpanConfTable
o Span Status Group:
This group supports MIB objects for retrieving span status
information. It contains the following table:
- hdsl2ShdslSpanStatusTable
Ray & Abbi Standards Track [Page 7]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
o Unit Inventory Group:
This group supports MIB objects for retrieving unit inventory
information about units in HDSL2/SHDSL lines via the EOC. It contains
the following table:
- hdsl2ShdslInventoryTable
o Segment Endpoint Configuration Group:
This group supports MIB objects for configuring parameters for the
HDSL2/SHDSL segment endpoints. It contains the following table:
- hdsl2ShdslEndpointConfTable
o Segment Endpoint Current Status/Performance Group:
This group supports MIB objects that provide the current
status/performance information relating to segment endpoints. It
contains the following table:
- hdsl2ShdslEndpointCurrTable
o Segment Endpoint 15-Minute Interval Status/Performance Group:
This group supports MIB objects that provide historic
status/performance information relating to segment endpoints in 15-
minute intervals. It contains the following table:
- hdsl2Shdsl15MinIntervalTable
o Segment Endpoint 1-Day Interval Status/Performance Group:
This group supports MIB objects that provide historic
status/performance information relating to segment endpoints in 1-day
intervals. It contains the following table:
- hdsl2Shdsl1DayIntervalTable
o Maintenance Group:
This group supports MIB objects for performing maintenance operations
such as loopbacks for HDSL2/SHDSL lines. It contains the following
table(s):
- hdsl2ShdslEndpointMaintTable
- hdsl2ShdslUnitMaintTable
Ray & Abbi Standards Track [Page 8]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
o Span Configuration Profile Group:
This group supports MIB objects for defining configuration profiles
for HDSL2/SHDSL Spans. It contains the following table:
- hdsl2ShdslSpanConfProfileTable
o Segment Endpoint Alarm Configuration Profile Group:
This group supports MIB objects for defining alarm configuration
profiles for HDSL2/SHDSL Segment Endpoints. It contains the
following table:
- hdsl2ShdslEndpointAlarmConfProfileTable
o Notifications Group:
This group defines the notifications supported for HDSL2/SHDSL lines:
- hdsl2ShdslLoopAttenCrossing
- hdsl2ShdslSNRMarginCrossing
- hdsl2ShdslPerfESThresh
- hdsl2ShdslPerfSESThresh
- hdsl2ShdslPerfCRCanomaliesThresh
- hdsl2ShdslPerfLOSWSThresh
- hdsl2ShdslPerfUASThresh
- hdsl2ShdslSpanInvalidNumRepeaters
- hdsl2ShdslLoopbackFailure
- hdsl2ShdslpowerBackoff
- hdsl2ShdsldeviceFault
- hdsl2ShdsldcContinuityFault
- hdsl2ShdslconfigInitFailure
- hdsl2ShdslprotocolInitFailure
- hdsl2ShdslnoNeighborPresent
- hdsl2ShdslLocalPowerLoss
An HDSL2/SHDSL Line consists of a minimum of two units - xtuC (the
central termination unit) and an xtuR (the remote termination unit).
The line may optionally support up to 8 repeater/regenerator units
(xru) as shown in the figure below.
Ray & Abbi Standards Track [Page 9]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
<-- Network Side Customer Side -->
|</////////////////// HDSL2/SHDSL Span ////////////////////>|
<~~~> <~~~> HDSL2/SHDSL Segments <~~~>
+-------+ +-------+ +-------+ +-------+ +-------+
+ C=1=N C=1=N C=..1..=N C=1=N +
| xtuC | | xru1 | | xru2 | | xru8 | | xtuR |
+ C=2=N C=2=N C=..2..=N C=2=N +
+-------+ +-------+ +-------+ +-------+ +-------+
Key: <////> HDSL2/SHDSL Span
<~~~~> HDSL2/SHDSL Segment
=1= HDSL2/SHDSL wire-pair-1
=2= SHDSL optional wire-pair-2 (Not applicable to HDSL2)
C Customer Side Segment Endpoint (modem)
N Network Side Segment Endpoint (modem)
Figure 2: General topology for an HDSL2/SHDSL Line
For SNR Margin, Loop Attenuation, ES, SES, CRC anomalies, LOSW, and
UAS, there are event counters, current 15-minute and 0 to 96 15-
minute history bucket(s) of "interval-counters", as well as current
and 0 to 30 previous 1-day interval-counter(s). Each current 15-
minute event bucket has an associated threshold notification.
Unlike RFC 2493 [22] and RFC 2662 [23], there is no representation in
the MIB for invalid buckets. In those cases where the data for an
interval is suspect or known to be invalid, the agent MUST NOT report
the interval. If the current 15-minute event bucket is determined to
be invalid, notifications based upon the value of the event bucket
MUST NOT be generated.
Not reporting an interval will result in holes in the associated
table. For example, the table, hdsl2Shdsl15MinIntervalTable, is
indexed by { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide,
hdsl2ShdslEndpointWirePair, hdsl2Shdsl15MinIntervalNumber}. If
interval 12 is determined to be invalid but intervals 11 and 13 are
valid, a Get Next operation on the indices .1.1.1.1.11 would return
indices .1.1.1.1.13.
Ray & Abbi Standards Track [Page 10]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
There is no requirement for an agent to ensure a fixed relationship
between the start of a fifteen minute interval and any wall clock;
however some implementations may align the fifteen minute intervals
with quarter hours. Likewise, an implementation may choose to align
one day intervals with the start of a day.
Counters are not reset when an xU is reinitialized, only when the
agent is reset or reinitialized (or under specific request outside
the scope of this MIB).
As a managed node can handle a large number of xUs, (e.g., hundreds
or perhaps thousands of lines), provisioning every parameter on every
xU may become burdensome. Moreover, most lines are provisioned
identically with the same set of parameters. To simplify the
provisioning process, this MIB makes use of profiles. A profile is a
set of parameters that can be shared by multiple lines using the same
configuration.
The following profiles are used in this MIB:
o Span Configuration Profiles - Span configuration profiles contain
parameters for configuring HDSL2/SHDSL spans. They are defined in
the hdsl2ShdslSpanConfProfileTable. Since span configuration
parameters are only applicable for SHDSL, the support for span
configuration profiles are optional for HDSL2 interfaces.
Note that the configuration of the span dictates the behavior for
each individual segment end point in the span. If a different
configuration is provisioned for any given segment end point
within the span, the new configuration for this segment end point
will override the span configuration for this segment end point
only.
o Segment Endpoint Alarm Configuration Profiles - These profiles
contain parameters for configuring alarm thresholds for
HDSL2/SHDSL segment endpoints. These profiles are defined in the
hdsl2ShdslEndpointAlarmConfProfileTable.
The index value for this profile is a locally-unique
administratively assigned name for the profile having the textual
convention `SnmpAdminString' (RFC 2571 [1]).
One or more lines may be configured to share parameters of a single
profile (e.g., hdsl2ShdslEndpointAlarmConfProfile = `silver') by
setting its hdsl2ShdslEndpointAlarmConfProfile objects to the value
of this profile. If a change is made to the profile, all lines that
Ray & Abbi Standards Track [Page 11]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
refer to it will be reconfigured to the changed parameters. Before a
profile can be deleted or taken out of service it must be first
unreferenced from all associated lines.
Implementations MUST provide a default profile whose name is `DEFVAL'
for each profile type. The values of the associated parameters will
be vendor specific unless otherwise indicated in this document.
Before a line's profiles have been set, these profiles will be
automatically used by setting hdsl2ShdslEndpointAlarmConfProfile and
hdsl2ShdslSpanConfProfile to `DEFVAL' where appropriate. This
default profile name, 'DEFVAL', is considered reserved in the context
of profiles defined in this MIB.
Profiles are created, assigned, and deleted dynamically using the
profile name and profile row status in each of the four profile
tables.
Profile changes MUST take effect immediately. These changes MAY
result in a restart (hard reset or soft restart) of the units on the
line.
The ability to generate the SNMP notifications coldStart/WarmStart
(per [21]) which are per agent (e.g., per Digital Subscriber Line
Access Multiplexer, or DSLAM, in such a device), and linkUp/linkDown
(per [21]) which are per interface (i.e., HDSL2/SHDSL line) is
required.
A linkDown notification MAY be generated whenever any of ES, SES, CRC
Anomaly, LOSW, or UAS event occurs. The corresponding linkUp
notification MAY be sent when all link failure conditions are
cleared.
The notifications defined in this MIB are for initialization failure
and for the threshold crossings associated with the following events:
ES, SES, CRC Anomaly, LOSW, and UAS. Each threshold has its own
enable/threshold value. When that value is 0, the notification is
disabled.
The hdsl2ShdslEndpointCurrStatus is a bitmask representing all
outstanding error conditions associated with a particular Segment
Endpoint. Note that since status of remote endpoints is obtained via
the EOC, this information may be unavailable for units that are
unreachable via EOC during a line error condition. Therefore, not
all conditions may always be included in its current status.
Notifications corresponding to the bit fields in this object are
defined.
Ray & Abbi Standards Track [Page 12]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
Two alarm conditions, SNR Margin Alarm and Loop Attenuation Alarm,
are organized in a manner slightly different from that implied in the
EOC specifications. In the MIB, these alarm conditions are tied to
the two thresholds hdsl2ShdslEndpointThreshSNRMargin and
hdsl2ShdslEndpointThreshLoopAttenuation found in the
hdsl2ShdslEndpointAlarmConfProfileTable. In the EOC, the alarm
conditions associated with these thresholds are per-unit. In the
MIB, these alarm conditions are per-endpoint. For terminal units,
this has no impact. For repeaters, this implies an implementation
variance where the agent in the terminal unit is responsible for
detecting a threshold crossing. As the reporting of a repeater
detected alarm condition to the polling terminal unit occurs in the
same EOC message as the reporting of the current SNR Margin and Loop
Attenuation values, it is anticipated that this will have very little
impact on agent implementation.
A threshold notification occurs whenever the corresponding current
15-minute interval error counter becomes equal to, or exceeds the
threshold value. One notification may be sent per interval per
interface. Since the current 15-minute counter is reset to 0 every
15 minutes, and if the condition persists, the notification may recur
as often as every 15 minutes. For example, to get a notification
whenever a "loss of" event occurs (but at most once every 15
minutes), set the corresponding threshold to 1. The agent will
generate a notification when the event originally occurs.
Note that the Network Management System, or NMS, may receive a
linkDown notification, as well, if enabled (via
ifLinkUpDownTrapEnable [21]). At the beginning of the next 15 minute
interval, the counter is reset. When the first second goes by and
the event occurs, the current interval bucket will be 1, which equals
the threshold, and the notification will be sent again.
A hdsl2ShdslSpanInvalidNumRepeaters notification may be generated
following completion of the discovery phase if the number of
repeaters discovered on the line differs from the number of repeaters
specified in hdsl2ShdslSpanConfNumRepeaters. For those conditions
where the number of provisioned repeaters is greater than those
encountered during span discovery, all table entries associated with
the nonexistent repeaters are to be discarded. For those conditions
where the number of provisioned repeaters is less than those
encountered during span discovery, additional table entries are to be
created using the default span configuration profile.
Ray & Abbi Standards Track [Page 13]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
For both HDSL2 and SHDSL lines, the following group(s) are mandatory:
hdsl2ShdslSpanConfGroup
hdsl2ShdslSpanStatusGroup
hdsl2ShdslInventoryGroup
hdsl2ShdslEndpointConfGroup
hdsl2Shdsl15MinIntervalGroup
hdsl2Shdsl1DayIntervalGroup
hdsl2ShdslMaintenanceGroup
hdsl2ShdslEndpointAlarmConfGroup
hdsl2ShdslNotificationGroup
For HDSL2 lines, the following group(s) are optional:
hdsl2ShdslSpanConfProfileGroup
hdsl2ShdslSpanShdslStatusGroup
HDSL2-SHDSL-LINE-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY,
OBJECT-TYPE,
Counter32,
Unsigned32,
Gauge32,
NOTIFICATION-TYPE,
Integer32,
transmission FROM SNMPv2-SMI
RowStatus,
TEXTUAL-CONVENTION FROM SNMPv2-TC
ifIndex FROM IF-MIB
PerfCurrentCount,
PerfIntervalCount FROM PerfHist-TC-MIB
SnmpAdminString FROM SNMP-FRAMEWORK-MIB
MODULE-COMPLIANCE,
OBJECT-GROUP,
NOTIFICATION-GROUP FROM SNMPv2-CONF;
hdsl2ShdslMIB MODULE-IDENTITY
LAST-UPDATED "200205090000Z" -- May 9, 2002
ORGANIZATION "ADSLMIB Working Group"
CONTACT-INFO "WG-email: adslmib@ietf.org
Info: https://www1.ietf.org/mailman/listinfo/adslmib
Chair: Mike Sneed
Ray & Abbi Standards Track [Page 14]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
Postal: P.O. Box 37324
Raleigh NC 27627-7324
Email: sneedmike@hotmail.com
Co-editor: Bob Ray
PESA Switching Systems, Inc.
Postal: 330-A Wynn Drive
Huntsville, AL 35805 USA
Email: rray@pesa.com
Phone: +1 256 726 9200 ext. 142
Co-editor: Rajesh Abbi
Alcatel USA
Postal: 2912 Wake Forest Road
Raleigh, NC 27609-7860 USA
Email: Rajesh.Abbi@alcatel.com
Phone: +1 919 850 6194
"
DESCRIPTION
"This MIB module defines a collection of objects for managing
HDSL2/SHDSL lines. An agent may reside at either end of the
line, however the MIB is designed to require no management
communication between the modems beyond that inherent in the
low-level EOC line protocol as defined in ANSI T1E1.4/2000-006
(for HDSL2 lines), or in ITU G.991.2 (for SHDSL lines)."
REVISION "200205090000Z" -- May 9, 2002
DESCRIPTION "Initial version, published as RFC 3276."
::= { transmission 48 }
hdsl2ShdslMibObjects OBJECT IDENTIFIER ::= { hdsl2ShdslMIB 1 }
-- Textual Conventions used in this MIB
--
Hdsl2ShdslPerfCurrDayCount ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"A gauge associated with interface performance measurements in
a current 1-day (24 hour) measurement interval.
The value of this gauge starts at zero at the beginning of an
interval and is increased when associated events occur, until
the end of the 1-day interval. At that time the value of the
gauge is stored in the previous 1-day history interval, as
defined in a companion object of type
Ray & Abbi Standards Track [Page 15]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
Hdsl2Shdsl1DayIntevalCount, and the current interval gauge
is restarted at zero.
In the case where the agent has no valid data available for
this interval the corresponding object instance is not
available and upon a retrieval request a corresponding error
message shall be returned to indicate that this instance does
not exist. Please note that zero is a valid value."
SYNTAX Gauge32
Hdsl2Shdsl1DayIntervalCount ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"A counter associated with interface performance measurements
during the most previous 1-day (24 hour) measurement interval.
The value of this gauge is equal to the value of the current
day gauge, as defined in a companion object of type
Hdsl2ShdslPerfCurrDayCount, at the end of its most recent
interval.
In the case where the agent has no valid data available for
this interval the corresponding object instance is not
available and upon a retrieval request a corresponding error
message shall be returned to indicate that this instance does
not exist."
SYNTAX Gauge32
Hdsl2ShdslPerfTimeElapsed ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The number of seconds that have elapsed since the beginning of
the current measurement period. If, for some reason, such as
an adjustment in the system's time-of-day clock or the addition
of a leap second, the current interval exceeds the maximum
value, the agent will return the maximum value.
For 15 minute intervals, the range is limited to (0..899).
For 24 hour intervals, the range is limited to (0..86399)."
SYNTAX Unsigned32(0..86399)
Hdsl2ShdslPerfIntervalThreshold ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This convention defines a range of values that may be set in
a fault threshold alarm control. As the number of seconds in
a 15-minute interval numbers at most 900, objects of this type
may have a range of 0...900, where the value of 0 disables the
alarm."
Ray & Abbi Standards Track [Page 16]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
SYNTAX Unsigned32(0..900)
Hdsl2ShdslUnitId ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This is the unique identification for all units in a
HDSL2/SHDSL Span. It is based on the EOC unit addressing
scheme with reference to the xtuC."
SYNTAX INTEGER
{
xtuC(1),
xtuR(2),
xru1(3),
xru2(4),
xru3(5),
xru4(6),
xru5(7),
xru6(8),
xru7(9),
xru8(10)
}
Hdsl2ShdslUnitSide ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This is the referenced side of a HDSL2/SHDSL unit - Network
or Customer side. The side facing the Network is the Network
side, while the side facing the Customer is the Customer side."
SYNTAX INTEGER
{
networkSide(1),
customerSide(2)
}
Hdsl2ShdslWirePair ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"This is the referenced pair of wires in a HDSL2/SHDSL Segment.
HDSL2 only supports a single pair (wirePair1), while SHDSL
supports an optional second pair (wirePair2)."
SYNTAX INTEGER
{
wirePair1(1),
wirePair2(2)
}
Hdsl2ShdslTransmissionModeType ::= TEXTUAL-CONVENTION
STATUS current
Ray & Abbi Standards Track [Page 17]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
DESCRIPTION
"Contains the regional setting of the HDSL2/SHDSL span,
represented as a bit-map of possible settings. The various
bit positions are:
Bit Meaning Description
1 region 1 Indicates ITU-T G.991.2 Annex A.
2 region 2 Indicates ITU-T G.991.2 Annex B."
SYNTAX BITS
{
region1(0),
region2(1)
}
Hdsl2ShdslClockReferenceType ::= TEXTUAL-CONVENTION
STATUS current
DESCRIPTION
"The various STU-C symbol clock references for the
HDSL2/SHDSL span, represented as an enumeration."
SYNTAX INTEGER
{
localClk(1), -- Mode-1 per G991.2
networkClk(2), -- Mode-2 per G991.2
dataOrNetworkClk(3), -- Mode-3a per G991.2
dataClk(4) -- Mode-3b per G991.2
}
-- Span Configuration Group
--
hdsl2ShdslSpanConfTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslSpanConfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table supports overall configuration of HDSL2/SHDSL
Spans. Entries in this table MUST be maintained in a
persistent manner."
::= { hdsl2ShdslMibObjects 1 }
hdsl2ShdslSpanConfEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslSpanConfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the hdsl2ShdslSpanConfTable. Each entry
represents the complete Span in a single HDSL2/SHDSL line.
It is indexed by the ifIndex of the associated HDSL2/SHDSL
Ray & Abbi Standards Track [Page 18]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
line."
INDEX { ifIndex }
::= { hdsl2ShdslSpanConfTable 1 }
Hdsl2ShdslSpanConfEntry ::=
SEQUENCE
{
hdsl2ShdslSpanConfNumRepeaters Unsigned32,
hdsl2ShdslSpanConfProfile SnmpAdminString,
hdsl2ShdslSpanConfAlarmProfile SnmpAdminString
}
hdsl2ShdslSpanConfNumRepeaters OBJECT-TYPE
SYNTAX Unsigned32(0..8)
UNITS "repeaters"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object provisions the number of repeaters/regenerators
in this HDSL2/SHDSL Span."
::= { hdsl2ShdslSpanConfEntry 1 }
hdsl2ShdslSpanConfProfile OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is a pointer to a span configuration profile in
the hdsl2ShdslSpanConfProfileTable, which applies to this span.
The value of this object is the index of the referenced profile
in the hdsl2ShdslSpanConfProfileTable. Note that span
configuration profiles are only applicable to SHDSL lines.
HDSL2 lines MUST reference the default profile, 'DEFVAL'.
By default, this object will have the value 'DEFVAL' (the index
of the default profile).
Any attempt to set this object to a value that is not the value
of the index for an active entry in the profile table,
hdsl2ShdslSpanConfProfileTable, MUST be rejected."
::= { hdsl2ShdslSpanConfEntry 2 }
hdsl2ShdslSpanConfAlarmProfile OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object is a pointer to an Alarm configuration profile in
Ray & Abbi Standards Track [Page 19]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
the hdsl2ShdslEndpointAlarmConfProfileTable. The value of this
object is the index of the referenced profile in the
hdsl2ShdslEndpointAlarmConfProfileTable. The alarm threshold
configuration in the referenced profile will be used by default
for all segment endpoints in this span. Individual endpoints
may override this profile by explicitly specifying some other
profile in the hdsl2ShdslEndpointConfTable. By default, this
object will have the value 'DEFVAL' (the index of the default
profile).
Any attempt to set this object to a value that is not the value
of the index for an active entry in the profile table,
hdsl2ShdslEndpointAlarmConfProfileTable, MUST be rejected."
::= { hdsl2ShdslSpanConfEntry 3 }
-- Span Status Group
--
hdsl2ShdslSpanStatusTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslSpanStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides overall status information of
HDSL2/SHDSL spans. This table contains live data from
equipment. As such, it is NOT persistent."
::= { hdsl2ShdslMibObjects 2 }
hdsl2ShdslSpanStatusEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslSpanStatusEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the hdsl2ShdslSpanStatusTable. Each entry
represents the complete span in a single HDSL2/SHDSL line.
It is indexed by the ifIndex of the associated HDSL2/SHDSL
line."
INDEX { ifIndex }
::= { hdsl2ShdslSpanStatusTable 1 }
Hdsl2ShdslSpanStatusEntry ::=
SEQUENCE
{
hdsl2ShdslStatusNumAvailRepeaters Unsigned32,
hdsl2ShdslStatusMaxAttainableLineRate Unsigned32,
hdsl2ShdslStatusActualLineRate Unsigned32,
hdsl2ShdslStatusTransmissionModeCurrent
Hdsl2ShdslTransmissionModeType
Ray & Abbi Standards Track [Page 20]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
}
hdsl2ShdslStatusNumAvailRepeaters OBJECT-TYPE
SYNTAX Unsigned32(0..8)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Contains the actual number of repeaters/regenerators
discovered in this HDSL2/SHDSL span."
::= { hdsl2ShdslSpanStatusEntry 1 }
hdsl2ShdslStatusMaxAttainableLineRate OBJECT-TYPE
SYNTAX Unsigned32(0..4112000)
UNITS "bps"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Contains the maximum attainable line rate in this HDSL2/SHDSL
span. This object provides the maximum rate the line is
capable of achieving. This is based upon measurements made
during line probing."
::= { hdsl2ShdslSpanStatusEntry 2 }
hdsl2ShdslStatusActualLineRate OBJECT-TYPE
SYNTAX Unsigned32(0..4112000)
UNITS "bps"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Contains the actual line rate in this HDSL2/SHDSL span. This
should equal ifSpeed."
::= { hdsl2ShdslSpanStatusEntry 3 }
hdsl2ShdslStatusTransmissionModeCurrent OBJECT-TYPE
SYNTAX Hdsl2ShdslTransmissionModeType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Contains the current Power Spectral Density (PSD) regional
setting of the HDSL2/SHDSL span."
::= { hdsl2ShdslSpanStatusEntry 4 }
-- Unit Inventory Group
--
hdsl2ShdslInventoryTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslInventoryEntry
MAX-ACCESS not-accessible
Ray & Abbi Standards Track [Page 21]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
STATUS current
DESCRIPTION
"This table supports retrieval of unit inventory information
available via the EOC from units in a HDSL2/SHDSL line.
Entries in this table are dynamically created during the
line discovery process. The life cycle for these entries
is as follows:
- xtu discovers a device, either a far-end xtu or an xru
- an inventory table entry is created for the device
- the line goes down for whatever reason
- inventory table entries for unreachable devices are
destroyed.
As these entries are created/destroyed dynamically, they
are NOT persistent."
::= { hdsl2ShdslMibObjects 3 }
hdsl2ShdslInventoryEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslInventoryEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the hdsl2ShdslInventoryTable. Each entry
represents inventory information for a single unit in a
HDSL2/SHDSL line. It is indexed by the ifIndex of the
HDSL2/SHDSL line and the Hdsl2ShdslUnitId of the
associated unit."
INDEX { ifIndex, hdsl2ShdslInvIndex }
::= { hdsl2ShdslInventoryTable 1 }
Hdsl2ShdslInventoryEntry ::=
SEQUENCE
{
hdsl2ShdslInvIndex Hdsl2ShdslUnitId,
hdsl2ShdslInvVendorID OCTET STRING,
hdsl2ShdslInvVendorModelNumber OCTET STRING,
hdsl2ShdslInvVendorSerialNumber OCTET STRING,
hdsl2ShdslInvVendorEOCSoftwareVersion Integer32,
hdsl2ShdslInvStandardVersion Integer32,
hdsl2ShdslInvVendorListNumber OCTET STRING,
hdsl2ShdslInvVendorIssueNumber OCTET STRING,
hdsl2ShdslInvVendorSoftwareVersion OCTET STRING,
hdsl2ShdslInvEquipmentCode OCTET STRING,
hdsl2ShdslInvVendorOther OCTET STRING,
hdsl2ShdslInvTransmissionModeCapability
Hdsl2ShdslTransmissionModeType
Ray & Abbi Standards Track [Page 22]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
}
hdsl2ShdslInvIndex OBJECT-TYPE
SYNTAX Hdsl2ShdslUnitId
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry in this table corresponds to a physical element
in a HDSL2/SHDSL Span. It is based on the EOC unit addressing
scheme with reference to the xtuC."
::= { hdsl2ShdslInventoryEntry 1 }
hdsl2ShdslInvVendorID OBJECT-TYPE
SYNTAX OCTET STRING(SIZE(8))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Vendor ID as reported in an Inventory Response message."
::= { hdsl2ShdslInventoryEntry 2 }
hdsl2ShdslInvVendorModelNumber OBJECT-TYPE
SYNTAX OCTET STRING(SIZE(12))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Vendor model number as reported in an Inventory Response
message."
::= { hdsl2ShdslInventoryEntry 3 }
hdsl2ShdslInvVendorSerialNumber OBJECT-TYPE
SYNTAX OCTET STRING(SIZE(12))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Vendor serial number as reported in an Inventory Response
message."
::= { hdsl2ShdslInventoryEntry 4 }
hdsl2ShdslInvVendorEOCSoftwareVersion OBJECT-TYPE
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Vendor EOC version as reported in a Discovery Response
message."
::= { hdsl2ShdslInventoryEntry 5 }
hdsl2ShdslInvStandardVersion OBJECT-TYPE
Ray & Abbi Standards Track [Page 23]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
SYNTAX Integer32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Version of the HDSL2/SHDSL standard implemented, as reported
in an Inventory Response message."
::= { hdsl2ShdslInventoryEntry 6 }
hdsl2ShdslInvVendorListNumber OBJECT-TYPE
SYNTAX OCTET STRING(SIZE(3))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Vendor list number as reported in an Inventory Response
message."
::= { hdsl2ShdslInventoryEntry 7 }
hdsl2ShdslInvVendorIssueNumber OBJECT-TYPE
SYNTAX OCTET STRING(SIZE(2))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Vendor issue number as reported in an Inventory Response
message."
::= { hdsl2ShdslInventoryEntry 8 }
hdsl2ShdslInvVendorSoftwareVersion OBJECT-TYPE
SYNTAX OCTET STRING(SIZE(6))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Vendor software version as reported in an Inventory Response
message."
::= { hdsl2ShdslInventoryEntry 9 }
hdsl2ShdslInvEquipmentCode OBJECT-TYPE
SYNTAX OCTET STRING(SIZE(10))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Equipment code conforming to ANSI T1.213, Coded Identification
of Equipment Entities."
::= { hdsl2ShdslInventoryEntry 10 }
hdsl2ShdslInvVendorOther OBJECT-TYPE
SYNTAX OCTET STRING(SIZE(12))
MAX-ACCESS read-only
STATUS current
Ray & Abbi Standards Track [Page 24]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
DESCRIPTION
"Other vendor information as reported in an Inventory Response
message."
::= { hdsl2ShdslInventoryEntry 11 }
hdsl2ShdslInvTransmissionModeCapability OBJECT-TYPE
SYNTAX Hdsl2ShdslTransmissionModeType
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Contains the transmission mode capability of the SHDSL unit."
::= { hdsl2ShdslInventoryEntry 12 }
-- Segment Endpoint Configuration Group
--
hdsl2ShdslEndpointConfTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslEndpointConfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table supports configuration parameters for segment
endpoints in a HDSL2/SHDSL line. As this table is indexed
by ifIndex, it MUST be maintained in a persistent manner."
::= { hdsl2ShdslMibObjects 4 }
hdsl2ShdslEndpointConfEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslEndpointConfEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the hdsl2ShdslEndpointConfTable. Each entry
represents a single segment endpoint in a HDSL2/SHDSL line.
It is indexed by the ifIndex of the HDSL2/SHDSL line, the
UnitId of the associated unit, the side of the unit, and the
wire-pair of the associated modem."
INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide,
hdsl2ShdslEndpointWirePair}
::= { hdsl2ShdslEndpointConfTable 1 }
Hdsl2ShdslEndpointConfEntry ::=
SEQUENCE
{
hdsl2ShdslEndpointSide Hdsl2ShdslUnitSide,
hdsl2ShdslEndpointWirePair Hdsl2ShdslWirePair,
hdsl2ShdslEndpointAlarmConfProfile SnmpAdminString
}
Ray & Abbi Standards Track [Page 25]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
hdsl2ShdslEndpointSide OBJECT-TYPE
SYNTAX Hdsl2ShdslUnitSide
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The side of the unit associated with this segment endpoint -
Network/Customer side - as per the Hdsl2ShdslUnitSide textual
convention."
::= { hdsl2ShdslEndpointConfEntry 1 }
hdsl2ShdslEndpointWirePair OBJECT-TYPE
SYNTAX Hdsl2ShdslWirePair
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The wire-pair of the modem associated with this segment
endpoint as per the Hdsl2ShdslWirePair textual convention."
::= { hdsl2ShdslEndpointConfEntry 2 }
hdsl2ShdslEndpointAlarmConfProfile OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(0..32))
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object configures the alarm threshold values to be used
for this segment endpoint. The values are obtained from the
alarm configuration profile referenced by this object. The
value of this object is the index of the referenced profile in
the hdsl2ShdslEndpointAlarmConfProfileTable, or NULL (a zero-
length SnmpAdminString). If the value is a zero-length
SnmpAdminString, the endpoint uses the default Alarm
Configuration Profile for the associated span as per the
hdsl2ShdslSpanConfAlarmProfile object in the
hdsl2ShdslSpanConfTable. The default value of this object is
a zero-length SnmpAdminString.
Any attempt to set this object to a value that is not the value
of the index for an active entry in the profile table,
hdsl2ShdslEndpointAlarmConfProfileTable, MUST be rejected."
::= { hdsl2ShdslEndpointConfEntry 3 }
-- Segment Endpoint Current Status/Performance Group
--
hdsl2ShdslEndpointCurrTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslEndpointCurrEntry
MAX-ACCESS not-accessible
STATUS current
Ray & Abbi Standards Track [Page 26]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
DESCRIPTION
"This table contains current status and performance information
for segment endpoints in HDSL2/SHDSL Lines. As with other
tables in this MIB indexed by ifIndex, entries in this table
MUST be maintained in a persistent manner."
::= { hdsl2ShdslMibObjects 5 }
hdsl2ShdslEndpointCurrEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslEndpointCurrEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the hdsl2ShdslEndpointCurrTable. Each entry
contains status and performance information relating to a
single segment endpoint. It is indexed by the ifIndex of the
HDSL2/SHDSL line, the UnitId of the associated unit, the side
of the unit, and the wire-pair of the associated modem."
INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide,
hdsl2ShdslEndpointWirePair }
::= { hdsl2ShdslEndpointCurrTable 1 }
Hdsl2ShdslEndpointCurrEntry ::=
SEQUENCE
{
hdsl2ShdslEndpointCurrAtn Integer32,
hdsl2ShdslEndpointCurrSnrMgn Integer32,
hdsl2ShdslEndpointCurrStatus BITS,
hdsl2ShdslEndpointES Counter32,
hdsl2ShdslEndpointSES Counter32,
hdsl2ShdslEndpointCRCanomalies Counter32,
hdsl2ShdslEndpointLOSWS Counter32,
hdsl2ShdslEndpointUAS Counter32,
hdsl2ShdslEndpointCurr15MinTimeElapsed
Hdsl2ShdslPerfTimeElapsed,
hdsl2ShdslEndpointCurr15MinES PerfCurrentCount,
hdsl2ShdslEndpointCurr15MinSES PerfCurrentCount,
hdsl2ShdslEndpointCurr15MinCRCanomalies PerfCurrentCount,
hdsl2ShdslEndpointCurr15MinLOSWS PerfCurrentCount,
hdsl2ShdslEndpointCurr15MinUAS PerfCurrentCount,
hdsl2ShdslEndpointCurr1DayTimeElapsed
Hdsl2ShdslPerfTimeElapsed,
hdsl2ShdslEndpointCurr1DayES
Hdsl2ShdslPerfCurrDayCount,
hdsl2ShdslEndpointCurr1DaySES
Hdsl2ShdslPerfCurrDayCount,
hdsl2ShdslEndpointCurr1DayCRCanomalies
Hdsl2ShdslPerfCurrDayCount,
hdsl2ShdslEndpointCurr1DayLOSWS
Ray & Abbi Standards Track [Page 27]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
Hdsl2ShdslPerfCurrDayCount,
hdsl2ShdslEndpointCurr1DayUAS
Hdsl2ShdslPerfCurrDayCount
}
hdsl2ShdslEndpointCurrAtn OBJECT-TYPE
SYNTAX Integer32(-127..128)
UNITS "dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current loop attenuation for this endpoint as reported in
a Network or Customer Side Performance Status message."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 1 }
hdsl2ShdslEndpointCurrSnrMgn OBJECT-TYPE
SYNTAX Integer32(-127..128)
UNITS "dB"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The current SNR margin for this endpoint as reported in a
Status Response/SNR message."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 2 }
hdsl2ShdslEndpointCurrStatus OBJECT-TYPE
SYNTAX BITS
{
noDefect(0),
powerBackoff(1),
deviceFault(2),
dcContinuityFault(3),
snrMarginAlarm(4),
loopAttenuationAlarm(5),
loswFailureAlarm(6),
configInitFailure(7),
protocolInitFailure(8),
noNeighborPresent(9),
loopbackActive(10)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Contains the current state of the endpoint. This is a
bitmap of possible conditions. The various bit positions
are:
Ray & Abbi Standards Track [Page 28]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
noDefect There no defects on the line.
powerBackoff Indicates enhanced Power Backoff.
deviceFault Indicates a vendor-dependent
diagnostic or self-test fault
has been detected.
dcContinuityFault Indicates vendor-dependent
conditions that interfere with
span powering such as short and
open circuits.
snrMarginAlarm Indicates that the SNR margin
has dropped below the alarm threshold.
loopAttenuationAlarm Indicates that the loop attenuation
exceeds the alarm threshold.
loswFailureAlarm Indicates a forward LOSW alarm.
configInitFailure Endpoint failure during initialization
due to paired endpoint not able to
support requested configuration.
protocolInitFailure Endpoint failure during initialization
due to incompatible protocol used by
the paired endpoint.
noNeighborPresent Endpoint failure during initialization
due to no activation sequence detected
from paired endpoint.
loopbackActive A loopback is currently active at this
Segment Endpoint.
This is intended to supplement ifOperStatus. Note that there
is a 1-1 relationship between the status bits defined in this
object and the notification thresholds defined elsewhere in
this MIB."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 3 }
hdsl2ShdslEndpointES OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
Ray & Abbi Standards Track [Page 29]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
DESCRIPTION
"Count of Errored Seconds (ES) on this endpoint since the xU
was last restarted."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 4 }
hdsl2ShdslEndpointSES OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Severely Errored Seconds (SES) on this endpoint
since the xU was last restarted."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 5 }
hdsl2ShdslEndpointCRCanomalies OBJECT-TYPE
SYNTAX Counter32
UNITS "detected CRC Anomalies"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of CRC anomalies on this endpoint since the xU was
last restarted."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 6 }
hdsl2ShdslEndpointLOSWS OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Loss of Sync Word (LOSW) Seconds on this endpoint
since the xU was last restarted."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 7 }
hdsl2ShdslEndpointUAS OBJECT-TYPE
SYNTAX Counter32
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Unavailable Seconds (UAS) on this endpoint since
the xU was last restarted."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
Ray & Abbi Standards Track [Page 30]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
::= { hdsl2ShdslEndpointCurrEntry 8 }
hdsl2ShdslEndpointCurr15MinTimeElapsed OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfTimeElapsed
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total elapsed seconds in the current 15-minute interval."
::= { hdsl2ShdslEndpointCurrEntry 9 }
hdsl2ShdslEndpointCurr15MinES OBJECT-TYPE
SYNTAX PerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Errored Seconds (ES) in the current 15-minute
interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 10 }
hdsl2ShdslEndpointCurr15MinSES OBJECT-TYPE
SYNTAX PerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Severely Errored Seconds (SES) in the current
15-minute interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 11 }
hdsl2ShdslEndpointCurr15MinCRCanomalies OBJECT-TYPE
SYNTAX PerfCurrentCount
UNITS "detected CRC Anomalies"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of CRC anomalies in the current 15-minute interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 12 }
hdsl2ShdslEndpointCurr15MinLOSWS OBJECT-TYPE
SYNTAX PerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
Ray & Abbi Standards Track [Page 31]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
DESCRIPTION
"Count of Loss of Sync Word (LOSW) Seconds in the current
15-minute interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 13 }
hdsl2ShdslEndpointCurr15MinUAS OBJECT-TYPE
SYNTAX PerfCurrentCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Unavailable Seconds (UAS) in the current 15-minute
interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 14 }
hdsl2ShdslEndpointCurr1DayTimeElapsed OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfTimeElapsed
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of seconds that have elapsed since the beginning of
the current 1-day interval."
::= { hdsl2ShdslEndpointCurrEntry 15 }
hdsl2ShdslEndpointCurr1DayES OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfCurrDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Errored Seconds (ES) during the current day as
measured by hdsl2ShdslEndpointCurr1DayTimeElapsed."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 16 }
hdsl2ShdslEndpointCurr1DaySES OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfCurrDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Severely Errored Seconds (SES) during the current
day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 17 }
Ray & Abbi Standards Track [Page 32]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
hdsl2ShdslEndpointCurr1DayCRCanomalies OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfCurrDayCount
UNITS "detected CRC Anomalies"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of CRC anomalies during the current day as measured
by hdsl2ShdslEndpointCurr1DayTimeElapsed."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 18 }
hdsl2ShdslEndpointCurr1DayLOSWS OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfCurrDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Loss of Sync Word (LOSW) Seconds during the current
day as measured by hdsl2ShdslEndpointCurr1DayTimeElapsed."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 19 }
hdsl2ShdslEndpointCurr1DayUAS OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfCurrDayCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Unavailable Seconds (UAS) during the current day as
measured by hdsl2ShdslEndpointCurr1DayTimeElapsed."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2ShdslEndpointCurrEntry 20 }
-- Segment Endpoint 15-Minute Interval Status/Performance Group
--
hdsl2Shdsl15MinIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2Shdsl15MinIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides one row for each HDSL2/SHDSL endpoint
performance data collection interval. This table contains
live data from equipment. As such, it is NOT persistent."
::= { hdsl2ShdslMibObjects 6 }
hdsl2Shdsl15MinIntervalEntry OBJECT-TYPE
SYNTAX Hdsl2Shdsl15MinIntervalEntry
Ray & Abbi Standards Track [Page 33]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the hdsl2Shdsl15MinIntervalTable."
INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide,
hdsl2ShdslEndpointWirePair, hdsl2Shdsl15MinIntervalNumber}
::= { hdsl2Shdsl15MinIntervalTable 1 }
Hdsl2Shdsl15MinIntervalEntry ::=
SEQUENCE
{
hdsl2Shdsl15MinIntervalNumber Unsigned32,
hdsl2Shdsl15MinIntervalES PerfIntervalCount,
hdsl2Shdsl15MinIntervalSES PerfIntervalCount,
hdsl2Shdsl15MinIntervalCRCanomalies PerfIntervalCount,
hdsl2Shdsl15MinIntervalLOSWS PerfIntervalCount,
hdsl2Shdsl15MinIntervalUAS PerfIntervalCount
}
hdsl2Shdsl15MinIntervalNumber OBJECT-TYPE
SYNTAX Unsigned32(1..96)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Performance Data Interval number. 1 is the the most recent
previous interval; interval 96 is 24 hours ago. Intervals
2..96 are optional."
::= { hdsl2Shdsl15MinIntervalEntry 1 }
hdsl2Shdsl15MinIntervalES OBJECT-TYPE
SYNTAX PerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Errored Seconds (ES) during the interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl15MinIntervalEntry 2 }
hdsl2Shdsl15MinIntervalSES OBJECT-TYPE
SYNTAX PerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Severely Errored Seconds (SES) during the interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl15MinIntervalEntry 3 }
Ray & Abbi Standards Track [Page 34]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
hdsl2Shdsl15MinIntervalCRCanomalies OBJECT-TYPE
SYNTAX PerfIntervalCount
UNITS "detected CRC Anomalies"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of CRC anomalies during the interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl15MinIntervalEntry 4 }
hdsl2Shdsl15MinIntervalLOSWS OBJECT-TYPE
SYNTAX PerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Loss of Sync Word (LOSW) Seconds during the
interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl15MinIntervalEntry 5 }
hdsl2Shdsl15MinIntervalUAS OBJECT-TYPE
SYNTAX PerfIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Unavailable Seconds (UAS) during the interval."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl15MinIntervalEntry 6 }
-- Segment Endpoint 1-Day Interval Status/Performance Group
--
hdsl2Shdsl1DayIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2Shdsl1DayIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table provides one row for each HDSL2/SHDSL endpoint
performance data collection interval. This table contains
live data from equipment. As such, it is NOT persistent."
::= { hdsl2ShdslMibObjects 7 }
hdsl2Shdsl1DayIntervalEntry OBJECT-TYPE
SYNTAX Hdsl2Shdsl1DayIntervalEntry
MAX-ACCESS not-accessible
STATUS current
Ray & Abbi Standards Track [Page 35]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
DESCRIPTION
"An entry in the hdsl2Shdsl1DayIntervalTable."
INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide,
hdsl2ShdslEndpointWirePair, hdsl2Shdsl1DayIntervalNumber }
::= { hdsl2Shdsl1DayIntervalTable 1 }
Hdsl2Shdsl1DayIntervalEntry ::=
SEQUENCE
{
hdsl2Shdsl1DayIntervalNumber Unsigned32,
hdsl2Shdsl1DayIntervalMoniSecs Hdsl2ShdslPerfTimeElapsed,
hdsl2Shdsl1DayIntervalES Hdsl2Shdsl1DayIntervalCount,
hdsl2Shdsl1DayIntervalSES Hdsl2Shdsl1DayIntervalCount,
hdsl2Shdsl1DayIntervalCRCanomalies Hdsl2Shdsl1DayIntervalCount,
hdsl2Shdsl1DayIntervalLOSWS Hdsl2Shdsl1DayIntervalCount,
hdsl2Shdsl1DayIntervalUAS Hdsl2Shdsl1DayIntervalCount
}
hdsl2Shdsl1DayIntervalNumber OBJECT-TYPE
SYNTAX Unsigned32(1..30)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"History Data Interval number. Interval 1 is the the most
recent previous day; interval 30 is 30 days ago. Intervals
2..30 are optional."
::= { hdsl2Shdsl1DayIntervalEntry 1 }
hdsl2Shdsl1DayIntervalMoniSecs OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfTimeElapsed
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The amount of time in the 1-day interval over which the
performance monitoring information is actually counted.
This value will be the same as the interval duration except
in a situation where performance monitoring data could not
be collected for any reason."
::= { hdsl2Shdsl1DayIntervalEntry 2 }
hdsl2Shdsl1DayIntervalES OBJECT-TYPE
SYNTAX Hdsl2Shdsl1DayIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Errored Seconds (ES) during the 1-day interval as
Ray & Abbi Standards Track [Page 36]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
measured by hdsl2Shdsl1DayIntervalMoniSecs."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl1DayIntervalEntry 3 }
hdsl2Shdsl1DayIntervalSES OBJECT-TYPE
SYNTAX Hdsl2Shdsl1DayIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Severely Errored Seconds (SES) during the 1-day
interval as measured by hdsl2Shdsl1DayIntervalMoniSecs."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl1DayIntervalEntry 4 }
hdsl2Shdsl1DayIntervalCRCanomalies OBJECT-TYPE
SYNTAX Hdsl2Shdsl1DayIntervalCount
UNITS "detected CRC Anomalies"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of CRC anomalies during the 1-day interval as
measured by hdsl2Shdsl1DayIntervalMoniSecs."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl1DayIntervalEntry 5 }
hdsl2Shdsl1DayIntervalLOSWS OBJECT-TYPE
SYNTAX Hdsl2Shdsl1DayIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Loss of Sync Word (LOSW) Seconds during the 1-day
interval as measured by hdsl2Shdsl1DayIntervalMoniSecs."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl1DayIntervalEntry 6 }
hdsl2Shdsl1DayIntervalUAS OBJECT-TYPE
SYNTAX Hdsl2Shdsl1DayIntervalCount
UNITS "seconds"
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Count of Unavailable Seconds (UAS) during the 1-day interval
as measured by hdsl2Shdsl1DayIntervalMoniSecs."
REFERENCE "HDSL2 Section 7.5.3.7; SHDSL Section 9.5.5.7"
::= { hdsl2Shdsl1DayIntervalEntry 7 }
Ray & Abbi Standards Track [Page 37]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
-- Maintenance Group
--
hdsl2ShdslEndpointMaintTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslEndpointMaintEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table supports maintenance operations (eg. loopbacks)
to be performed on HDSL2/SHDSL segment endpoints. This table
contains live data from equipment. As such, it is NOT
persistent."
::= { hdsl2ShdslMibObjects 8 }
hdsl2ShdslEndpointMaintEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslEndpointMaintEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the hdsl2ShdslEndpointMaintTable. Each entry
corresponds to a single segment endpoint, and is indexed by the
ifIndex of the HDSL2/SHDSL line, the UnitId of the associated
unit and the side of the unit."
INDEX { ifIndex, hdsl2ShdslInvIndex, hdsl2ShdslEndpointSide }
::= { hdsl2ShdslEndpointMaintTable 1 }
Hdsl2ShdslEndpointMaintEntry ::=
SEQUENCE
{
hdsl2ShdslMaintLoopbackConfig INTEGER,
hdsl2ShdslMaintTipRingReversal INTEGER,
hdsl2ShdslMaintPowerBackOff INTEGER,
hdsl2ShdslMaintSoftRestart INTEGER
}
hdsl2ShdslMaintLoopbackConfig OBJECT-TYPE
SYNTAX INTEGER
{
noLoopback(1),
normalLoopback(2),
specialLoopback(3)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object controls configuration of loopbacks for the
associated segment endpoint. The status of the loopback
is obtained via the hdsl2ShdslEndpointCurrStatus object."
Ray & Abbi Standards Track [Page 38]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
::= { hdsl2ShdslEndpointMaintEntry 1 }
hdsl2ShdslMaintTipRingReversal OBJECT-TYPE
SYNTAX INTEGER
{
normal(1),
reversed(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the state of the tip/ring pair at the
associated segment endpoint."
::= { hdsl2ShdslEndpointMaintEntry 2 }
hdsl2ShdslMaintPowerBackOff OBJECT-TYPE
SYNTAX INTEGER
{
default(1),
enhanced(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object configures the receiver at the associated
segment endpoint to operate in default or enhanced power
backoff mode."
::= { hdsl2ShdslEndpointMaintEntry 3 }
hdsl2ShdslMaintSoftRestart OBJECT-TYPE
SYNTAX INTEGER
{
ready(1),
restart(2)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object enables the manager to trigger a soft restart
of the modem at the associated segment endpoint. The manager
may only set this object to the 'restart(2)' value, which
initiates a restart. The agent will perform a restart after
approximately 5 seconds. Following the 5 second period, the
agent will restore the object to the 'ready(1)' state."
::= { hdsl2ShdslEndpointMaintEntry 4 }
hdsl2ShdslUnitMaintTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslUnitMaintEntry
Ray & Abbi Standards Track [Page 39]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table supports maintenance operations for units in a
HDSL2/SHDSL line. Entries in this table MUST be maintained
in a persistent manner."
::= { hdsl2ShdslMibObjects 9 }
hdsl2ShdslUnitMaintEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslUnitMaintEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the hdsl2ShdslUnitMaintTable. Each entry
corresponds to a single unit, and is indexed by the ifIndex
of the HDSL2/SHDSL line and the UnitId of the associated
unit."
INDEX { ifIndex, hdsl2ShdslInvIndex }
::= { hdsl2ShdslUnitMaintTable 1 }
Hdsl2ShdslUnitMaintEntry ::=
SEQUENCE
{
hdsl2ShdslMaintLoopbackTimeout Integer32,
hdsl2ShdslMaintUnitPowerSource INTEGER
}
hdsl2ShdslMaintLoopbackTimeout OBJECT-TYPE
SYNTAX Integer32(0..4095)
UNITS "minutes"
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"This object configures the timeout value for loopbacks
initiated at segments endpoints contained in the associated
unit. A value of 0 disables the timeout."
::= { hdsl2ShdslUnitMaintEntry 1 }
hdsl2ShdslMaintUnitPowerSource OBJECT-TYPE
SYNTAX INTEGER
{
local(1),
span(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This object indicates the DC power source being used by the
Ray & Abbi Standards Track [Page 40]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
associated unit."
::= { hdsl2ShdslUnitMaintEntry 2 }
-- Span Configuration Profile Group
--
hdsl2ShdslSpanConfProfileTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslSpanConfProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table supports definitions of span configuration
profiles for SHDSL lines. HDSL2 does not support these
configuration options. This table MUST be maintained
in a persistent manner."
::= { hdsl2ShdslMibObjects 10 }
hdsl2ShdslSpanConfProfileEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslSpanConfProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry corresponds to a single span configuration
profile. Each profile contains a set of span configuration
parameters. The configuration parameters in a profile are
applied to those lines referencing that profile (see the
hdsl2ShdslSpanConfProfile object). Profiles may be
created/deleted using the row creation/deletion mechanism
via hdsl2ShdslSpanConfProfileRowStatus. If an active
entry is referenced in hdsl2ShdslSpanConfProfile, the
entry MUST remain active until all references are removed."
INDEX { IMPLIED hdsl2ShdslSpanConfProfileName }
::= { hdsl2ShdslSpanConfProfileTable 1 }
Hdsl2ShdslSpanConfProfileEntry ::=
SEQUENCE
{
hdsl2ShdslSpanConfProfileName SnmpAdminString,
hdsl2ShdslSpanConfWireInterface INTEGER,
hdsl2ShdslSpanConfMinLineRate Unsigned32,
hdsl2ShdslSpanConfMaxLineRate Unsigned32,
hdsl2ShdslSpanConfPSD INTEGER,
hdsl2ShdslSpanConfTransmissionMode
Hdsl2ShdslTransmissionModeType,
hdsl2ShdslSpanConfRemoteEnabled INTEGER,
hdsl2ShdslSpanConfPowerFeeding INTEGER,
hdsl2ShdslSpanConfCurrCondTargetMarginDown Integer32,
hdsl2ShdslSpanConfWorstCaseTargetMarginDown Integer32,
Ray & Abbi Standards Track [Page 41]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
hdsl2ShdslSpanConfCurrCondTargetMarginUp Integer32,
hdsl2ShdslSpanConfWorstCaseTargetMarginUp Integer32,
hdsl2ShdslSpanConfUsedTargetMargins BITS,
hdsl2ShdslSpanConfReferenceClock
Hdsl2ShdslClockReferenceType,
hdsl2ShdslSpanConfLineProbeEnable INTEGER,
hdsl2ShdslSpanConfProfileRowStatus RowStatus
}
hdsl2ShdslSpanConfProfileName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This object is the unique index associated with this profile.
Entries in this table are referenced via the object
hdsl2ShdslSpanConfProfile in Hdsl2ShdslSpanConfEntry."
::= { hdsl2ShdslSpanConfProfileEntry 1 }
hdsl2ShdslSpanConfWireInterface OBJECT-TYPE
SYNTAX INTEGER
{
twoWire(1),
fourWire(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the two-wire or optional four-wire
operation for SHDSL Lines."
DEFVAL { twoWire }
::= { hdsl2ShdslSpanConfProfileEntry 2 }
hdsl2ShdslSpanConfMinLineRate OBJECT-TYPE
SYNTAX Unsigned32(0..4112000)
UNITS "bps"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the minimum transmission rate for
the associated SHDSL Line in bits-per-second (bps). If
the minimum line rate equals the maximum line rate
(hdsl2ShdslSpanMaxLineRate), the line rate is considered
'fixed'. If the minimum line rate is less than the maximum
line rate, the line rate is considered 'rate-adaptive'."
DEFVAL { 1552000 }
::= { hdsl2ShdslSpanConfProfileEntry 3 }
Ray & Abbi Standards Track [Page 42]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
hdsl2ShdslSpanConfMaxLineRate OBJECT-TYPE
SYNTAX Unsigned32(0..4112000)
UNITS "bps"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the maximum transmission rate for
the associated SHDSL Line in bits-per-second (bps). If
the minimum line rate equals the maximum line rate
(hdsl2ShdslSpanMaxLineRate), the line rate is considered
'fixed'. If the minimum line rate is less than the maximum
line rate, the line rate is considered 'rate-adaptive'."
DEFVAL { 1552000 }
::= { hdsl2ShdslSpanConfProfileEntry 4 }
hdsl2ShdslSpanConfPSD OBJECT-TYPE
SYNTAX INTEGER
{
symmetric(1),
asymmetric(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures use of symmetric/asymmetric PSD (Power
Spectral Density) Mask for the associated SHDSL Line. Support
for symmetric PSD is mandatory for all supported data rates.
Support for asymmetric PSD is optional."
DEFVAL { symmetric }
::= { hdsl2ShdslSpanConfProfileEntry 5 }
hdsl2ShdslSpanConfTransmissionMode OBJECT-TYPE
SYNTAX Hdsl2ShdslTransmissionModeType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the regional setting for the SHDSL
line."
DEFVAL { { region1 } }
::= { hdsl2ShdslSpanConfProfileEntry 6 }
hdsl2ShdslSpanConfRemoteEnabled OBJECT-TYPE
SYNTAX INTEGER
{
enabled(1),
disabled(2)
}
MAX-ACCESS read-create
Ray & Abbi Standards Track [Page 43]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
STATUS current
DESCRIPTION
"This object enables/disables support for remote management
of the units in a SHDSL line from the STU-R via the EOC."
DEFVAL { enabled }
::= { hdsl2ShdslSpanConfProfileEntry 7 }
hdsl2ShdslSpanConfPowerFeeding OBJECT-TYPE
SYNTAX INTEGER
{
noPower(1),
powerFeed(2),
wettingCurrent(3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object enables/disables support for optional power
feeding in a SHDSL line."
DEFVAL { noPower }
::= { hdsl2ShdslSpanConfProfileEntry 8 }
hdsl2ShdslSpanConfCurrCondTargetMarginDown OBJECT-TYPE
SYNTAX Integer32(-10..21)
UNITS "dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the downstream current condition target
SNR margin for a SHDSL line. The SNR margin is the difference
between the desired SNR and the actual SNR. Target SNR margin
is the desired SNR margin for a unit."
DEFVAL { 0 }
::= { hdsl2ShdslSpanConfProfileEntry 9 }
hdsl2ShdslSpanConfWorstCaseTargetMarginDown OBJECT-TYPE
SYNTAX Integer32(-10..21)
UNITS "dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the downstream worst case target SNR
margin for a SHDSL line. The SNR margin is the difference
between the desired SNR and the actual SNR. Target SNR
margin is the desired SNR margin for a unit."
DEFVAL { 0 }
::= { hdsl2ShdslSpanConfProfileEntry 10 }
Ray & Abbi Standards Track [Page 44]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
hdsl2ShdslSpanConfCurrCondTargetMarginUp OBJECT-TYPE
SYNTAX Integer32(-10..21)
UNITS "dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the upstream current condition target
SNR margin for a SHDSL line. The SNR margin is the difference
between the desired SNR and the actual SNR. Target SNR margin
is the desired SNR margin for a unit."
DEFVAL { 0 }
::= { hdsl2ShdslSpanConfProfileEntry 11 }
hdsl2ShdslSpanConfWorstCaseTargetMarginUp OBJECT-TYPE
SYNTAX Integer32(-10..21)
UNITS "dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object specifies the upstream worst case target SNR
margin for a SHDSL line. The SNR margin is the difference
between the desired SNR and the actual SNR. Target SNR margin
is the desired SNR margin for a unit."
DEFVAL { 0 }
::= { hdsl2ShdslSpanConfProfileEntry 12 }
hdsl2ShdslSpanConfUsedTargetMargins OBJECT-TYPE
SYNTAX BITS
{
currCondDown(0),
worstCaseDown(1),
currCondUp(2),
worstCaseUp(3)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"Contains indicates whether a target SNR margin is enabled or
disabled. This is a bit-map of possible settings. The
various bit positions are:
currCondDown current condition downstream target SNR
margin enabled
worstCaseDown worst case downstream target SNR margin
enabled
currCondUp current condition upstream target SNR
Ray & Abbi Standards Track [Page 45]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
margin enabled
worstCaseUp worst case upstream target SNR margin
enabled."
DEFVAL { { currCondDown } }
::= { hdsl2ShdslSpanConfProfileEntry 13 }
hdsl2ShdslSpanConfReferenceClock OBJECT-TYPE
SYNTAX Hdsl2ShdslClockReferenceType
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the clock reference for the STU-C
in a SHDSL Line."
DEFVAL { localClk }
::= { hdsl2ShdslSpanConfProfileEntry 14 }
hdsl2ShdslSpanConfLineProbeEnable OBJECT-TYPE
SYNTAX INTEGER
{
disable(1),
enable(2)
}
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object enables/disables support for Line Probe of
the units in a SHDSL line. When Line Probe is enabled, the
system performs Line Probing to find the best possible
rate. If Line probe is disabled, the rate adaptation phase
is skipped to shorten set up time."
DEFVAL { disable }
::= { hdsl2ShdslSpanConfProfileEntry 15 }
hdsl2ShdslSpanConfProfileRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object controls creation/deletion of the associated
entry in this table per the semantics of RowStatus. If an
active entry is referenced in hdsl2ShdslSpanConfProfile, the
entry MUST remain active until all references are removed."
::= { hdsl2ShdslSpanConfProfileEntry 16 }
-- Segment Endpoint Alarm Configuration Profile group
--
Ray & Abbi Standards Track [Page 46]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
hdsl2ShdslEndpointAlarmConfProfileTable OBJECT-TYPE
SYNTAX SEQUENCE OF Hdsl2ShdslEndpointAlarmConfProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"This table supports definitions of alarm configuration
profiles for HDSL2/SHDSL segment endpoints. This table
MUST be maintained in a persistent manner."
::= { hdsl2ShdslMibObjects 11 }
hdsl2ShdslEndpointAlarmConfProfileEntry OBJECT-TYPE
SYNTAX Hdsl2ShdslEndpointAlarmConfProfileEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Each entry corresponds to a single alarm configuration profile.
Each profile contains a set of parameters for setting alarm
thresholds for various performance attributes monitored at
HDSL2/SHDSL segment endpoints. Profiles may be created/deleted
using the row creation/deletion mechanism via
hdsl2ShdslEndpointAlarmConfProfileRowStatus. If an active
entry is referenced in either hdsl2ShdslSpanConfAlarmProfile
or hdsl2ShdslEndpointAlarmConfProfile, the entry MUST remain
active until all references are removed."
INDEX { IMPLIED hdsl2ShdslEndpointAlarmConfProfileName }
::= { hdsl2ShdslEndpointAlarmConfProfileTable 1 }
Hdsl2ShdslEndpointAlarmConfProfileEntry ::=
SEQUENCE
{
hdsl2ShdslEndpointAlarmConfProfileName SnmpAdminString,
hdsl2ShdslEndpointThreshLoopAttenuation Integer32,
hdsl2ShdslEndpointThreshSNRMargin Integer32,
hdsl2ShdslEndpointThreshES
Hdsl2ShdslPerfIntervalThreshold,
hdsl2ShdslEndpointThreshSES
Hdsl2ShdslPerfIntervalThreshold,
hdsl2ShdslEndpointThreshCRCanomalies Integer32,
hdsl2ShdslEndpointThreshLOSWS
Hdsl2ShdslPerfIntervalThreshold,
hdsl2ShdslEndpointThreshUAS
Hdsl2ShdslPerfIntervalThreshold,
hdsl2ShdslEndpointAlarmConfProfileRowStatus RowStatus
}
hdsl2ShdslEndpointAlarmConfProfileName OBJECT-TYPE
SYNTAX SnmpAdminString (SIZE(1..32))
MAX-ACCESS not-accessible
Ray & Abbi Standards Track [Page 47]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
STATUS current
DESCRIPTION
"This object is the unique index associated with this profile."
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 1 }
hdsl2ShdslEndpointThreshLoopAttenuation OBJECT-TYPE
SYNTAX Integer32(-127..128)
UNITS "dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the loop attenuation alarm threshold.
When the current value of hdsl2ShdslEndpointCurrAtn reaches
or exceeds this threshold, a hdsl2ShdslLoopAttenCrossing
MAY be generated."
DEFVAL { 0 }
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 2 }
hdsl2ShdslEndpointThreshSNRMargin OBJECT-TYPE
SYNTAX Integer32(-127..128)
UNITS "dB"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the SNR margin alarm threshold.
When the current value of hdsl2ShdslEndpointCurrSnrMgn
reaches or drops below this threshold, a
hdsl2ShdslSNRMarginCrossing MAY be generated."
DEFVAL { 0 }
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 3 }
hdsl2ShdslEndpointThreshES OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the threshold for the number of
errored seconds (ES) within any given 15-minute performance
data collection interval. If the value of errored seconds
in a particular 15-minute collection interval reaches/
exceeds this value, a hdsl2ShdslPerfESThresh MAY be
generated. At most one notification will be sent per
interval per endpoint."
DEFVAL { 0 }
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 4 }
hdsl2ShdslEndpointThreshSES OBJECT-TYPE
Ray & Abbi Standards Track [Page 48]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
SYNTAX Hdsl2ShdslPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the threshold for the number of
severely errored seconds (SES) within any given 15-minute
performance data collection interval. If the value of
severely errored seconds in a particular 15-minute collection
interval reaches/exceeds this value, a hdsl2ShdslPerfSESThresh
MAY be generated. At most one notification will be sent per
interval per endpoint."
DEFVAL { 0 }
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 5 }
hdsl2ShdslEndpointThreshCRCanomalies OBJECT-TYPE
SYNTAX Integer32
UNITS "detected CRC Anomalies"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the threshold for the number of
CRC anomalies within any given 15-minute performance data
collection interval. If the value of CRC anomalies in a
particular 15-minute collection interval reaches/exceeds
this value, a hdsl2ShdslPerfCRCanomaliesThresh MAY be
generated. At most one notification will be sent per
interval per endpoint."
DEFVAL { 0 }
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 6 }
hdsl2ShdslEndpointThreshLOSWS OBJECT-TYPE
SYNTAX Hdsl2ShdslPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the threshold for the number of
Loss of Sync Word (LOSW) Seconds within any given 15-minute
performance data collection interval. If the value of LOSW
in a particular 15-minute collection interval reaches/exceeds
this value, a hdsl2ShdslPerfLOSWSThresh MAY be generated.
At most one notification will be sent per interval per
endpoint."
DEFVAL { 0 }
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 7 }
hdsl2ShdslEndpointThreshUAS OBJECT-TYPE
Ray & Abbi Standards Track [Page 49]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
SYNTAX Hdsl2ShdslPerfIntervalThreshold
UNITS "seconds"
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object configures the threshold for the number of
unavailable seconds (UAS) within any given 15-minute
performance data collection interval. If the value of UAS
in a particular 15-minute collection interval reaches/exceeds
this value, a hdsl2ShdslPerfUASThresh MAY be generated.
At most one notification will be sent per interval per
endpoint."
DEFVAL { 0 }
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 8 }
hdsl2ShdslEndpointAlarmConfProfileRowStatus OBJECT-TYPE
SYNTAX RowStatus
MAX-ACCESS read-create
STATUS current
DESCRIPTION
"This object controls creation/deletion of the associated
entry in this table as per the semantics of RowStatus.
If an active entry is referenced in either
hdsl2ShdslSpanConfAlarmProfile or
hdsl2ShdslEndpointAlarmConfProfile, the entry MUST remain
active until all references are removed."
::= { hdsl2ShdslEndpointAlarmConfProfileEntry 9 }
-- Notifications Group
--
hdsl2ShdslNotifications OBJECT IDENTIFIER ::= { hdsl2ShdslMIB 0 }
hdsl2ShdslLoopAttenCrossing NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurrAtn,
hdsl2ShdslEndpointThreshLoopAttenuation
}
STATUS current
DESCRIPTION
"This notification indicates that the loop attenuation
threshold (as per the hdsl2ShdslEndpointThreshLoopAttenuation
value) has been reached/exceeded for the HDSL2/SHDSL segment
endpoint."
::= { hdsl2ShdslNotifications 1 }
hdsl2ShdslSNRMarginCrossing NOTIFICATION-TYPE
Ray & Abbi Standards Track [Page 50]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
OBJECTS
{
hdsl2ShdslEndpointCurrSnrMgn,
hdsl2ShdslEndpointThreshSNRMargin
}
STATUS current
DESCRIPTION
"This notification indicates that the SNR margin threshold (as
per the hdsl2ShdslEndpointThreshSNRMargin value) has been
reached/exceeded for the HDSL2/SHDSL segment endpoint."
::= { hdsl2ShdslNotifications 2 }
hdsl2ShdslPerfESThresh NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurr15MinES,
hdsl2ShdslEndpointThreshES
}
STATUS current
DESCRIPTION
"This notification indicates that the errored seconds threshold
(as per the hdsl2ShdslEndpointThreshES value) has been reached/
exceeded for the HDSL2/SHDSL segment endpoint."
::= { hdsl2ShdslNotifications 3 }
hdsl2ShdslPerfSESThresh NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurr15MinSES,
hdsl2ShdslEndpointThreshSES
}
STATUS current
DESCRIPTION
"This notification indicates that the severely errored seconds
threshold (as per the hdsl2ShdslEndpointThreshSES value) has
been reached/exceeded for the HDSL2/SHDSL Segment Endpoint."
::= { hdsl2ShdslNotifications 4 }
hdsl2ShdslPerfCRCanomaliesThresh NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurr15MinCRCanomalies,
hdsl2ShdslEndpointThreshCRCanomalies
}
STATUS current
DESCRIPTION
"This notification indicates that the CRC anomalies threshold
Ray & Abbi Standards Track [Page 51]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
(as per the hdsl2ShdslEndpointThreshCRCanomalies value) has
been reached/exceeded for the HDSL2/SHDSL Segment Endpoint."
::= { hdsl2ShdslNotifications 5 }
hdsl2ShdslPerfLOSWSThresh NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurr15MinLOSWS,
hdsl2ShdslEndpointThreshLOSWS
}
STATUS current
DESCRIPTION
"This notification indicates that the LOSW seconds threshold
(as per the hdsl2ShdslEndpointThreshLOSWS value) has been
reached/exceeded for the HDSL2/SHDSL segment endpoint."
::= { hdsl2ShdslNotifications 6 }
hdsl2ShdslPerfUASThresh NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurr15MinUAS,
hdsl2ShdslEndpointThreshUAS
}
STATUS current
DESCRIPTION
"This notification indicates that the unavailable seconds
threshold (as per the hdsl2ShdslEndpointThreshUAS value) has
been reached/exceeded for the HDSL2/SHDSL segment endpoint."
::= { hdsl2ShdslNotifications 7 }
hdsl2ShdslSpanInvalidNumRepeaters NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslSpanConfNumRepeaters
}
STATUS current
DESCRIPTION
"This notification indicates that a mismatch has been detected
between the number of repeater/regenerator units configured
for a HDSL2/SHDSL line via the hdsl2ShdslSpanConfNumRepeaters
object and the actual number of repeater/regenerator units
discovered via the EOC."
::= { hdsl2ShdslNotifications 8 }
hdsl2ShdslLoopbackFailure NOTIFICATION-TYPE
OBJECTS
{
Ray & Abbi Standards Track [Page 52]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
hdsl2ShdslMaintLoopbackConfig
}
STATUS current
DESCRIPTION
"This notification indicates that an endpoint maintenance
loopback command failed for an HDSL2/SHDSL segment."
::= { hdsl2ShdslNotifications 9 }
hdsl2ShdslpowerBackoff NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurrStatus
}
STATUS current
DESCRIPTION
"This notification indicates that the bit setting for
powerBackoff in the hdsl2ShdslEndpointCurrStatus object for
this endpoint has changed."
::= { hdsl2ShdslNotifications 10 }
hdsl2ShdsldeviceFault NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurrStatus
}
STATUS current
DESCRIPTION
"This notification indicates that the bit setting for
deviceFault in the hdsl2ShdslEndpointCurrStatus object for
this endpoint has changed."
::= { hdsl2ShdslNotifications 11 }
hdsl2ShdsldcContinuityFault NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurrStatus
}
STATUS current
DESCRIPTION
"This notification indicates that the bit setting for
dcContinuityFault in the hdsl2ShdslEndpointCurrStatus object
for this endpoint has changed."
::= { hdsl2ShdslNotifications 12 }
hdsl2ShdslconfigInitFailure NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurrStatus
Ray & Abbi Standards Track [Page 53]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
}
STATUS current
DESCRIPTION
"This notification indicates that the bit setting for
configInitFailure in the hdsl2ShdslEndpointCurrStatus object
for this endpoint has changed."
::= { hdsl2ShdslNotifications 13 }
hdsl2ShdslprotocolInitFailure NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurrStatus
}
STATUS current
DESCRIPTION
"This notification indicates that the bit setting for
protocolInitFailure in the hdsl2ShdslEndpointCurrStatus
object for this endpoint has changed."
::= { hdsl2ShdslNotifications 14 }
hdsl2ShdslnoNeighborPresent NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslEndpointCurrStatus
}
STATUS current
DESCRIPTION
"This notification indicates that the bit setting for
noNeighborPresent in the hdsl2ShdslEndpointCurrStatus object
for this endpoint has changed."
::= { hdsl2ShdslNotifications 15 }
hdsl2ShdslLocalPowerLoss NOTIFICATION-TYPE
OBJECTS
{
hdsl2ShdslInvVendorID
}
STATUS current
DESCRIPTION
"This notification indicates impending unit failure due to
loss of local power (last gasp)."
::= { hdsl2ShdslNotifications 16 }
-- conformance information
--
hdsl2ShdslConformance OBJECT IDENTIFIER ::= { hdsl2ShdslMIB 3 }
hdsl2ShdslGroups OBJECT IDENTIFIER ::=
Ray & Abbi Standards Track [Page 54]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
{ hdsl2ShdslConformance 1 }
hdsl2ShdslCompliances OBJECT IDENTIFIER ::=
{ hdsl2ShdslConformance 2 }
-- agent compliance statements
hdsl2ShdslLineMibCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The section outlines compliance requirements for this MIB."
MODULE
MANDATORY-GROUPS
{
hdsl2ShdslSpanConfGroup,
hdsl2ShdslSpanStatusGroup,
hdsl2ShdslInventoryGroup,
hdsl2ShdslEndpointConfGroup,
hdsl2ShdslEndpointCurrGroup,
hdsl2Shdsl15MinIntervalGroup,
hdsl2Shdsl1DayIntervalGroup,
hdsl2ShdslMaintenanceGroup,
hdsl2ShdslEndpointAlarmConfGroup,
hdsl2ShdslNotificationGroup
}
GROUP hdsl2ShdslInventoryShdslGroup
DESCRIPTION
"Support for this group is only required for implementations
supporting SHDSL lines."
GROUP hdsl2ShdslSpanShdslStatusGroup
DESCRIPTION
"Support for this group is only required for implementations
supporting SHDSL lines."
GROUP hdsl2ShdslSpanConfProfileGroup
DESCRIPTION
"Support for this group is only required for implementations
supporting SHDSL lines."
::= { hdsl2ShdslCompliances 1 }
-- units of conformance
--
hdsl2ShdslSpanConfGroup OBJECT-GROUP
OBJECTS
{
Ray & Abbi Standards Track [Page 55]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
hdsl2ShdslSpanConfNumRepeaters,
hdsl2ShdslSpanConfProfile,
hdsl2ShdslSpanConfAlarmProfile
}
STATUS current
DESCRIPTION
"This group supports objects for configuring span related
parameters for HDSL2/SHDSL lines."
::= { hdsl2ShdslGroups 1 }
hdsl2ShdslSpanStatusGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslStatusNumAvailRepeaters
}
STATUS current
DESCRIPTION
"This group supports objects for retrieving span related
status for HDSL2/SHDSL lines."
::= { hdsl2ShdslGroups 2 }
hdsl2ShdslInventoryShdslGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslInvTransmissionModeCapability
}
STATUS current
DESCRIPTION
"This group supports objects for retrieving SHDSL-specific
inventory information."
::= { hdsl2ShdslGroups 3 }
hdsl2ShdslSpanShdslStatusGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslStatusMaxAttainableLineRate,
hdsl2ShdslStatusActualLineRate,
hdsl2ShdslStatusTransmissionModeCurrent
}
STATUS current
DESCRIPTION
"This group supports objects for retrieving SHDSL-specific
span related status."
::= { hdsl2ShdslGroups 4 }
hdsl2ShdslInventoryGroup OBJECT-GROUP
OBJECTS
{
Ray & Abbi Standards Track [Page 56]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
hdsl2ShdslInvVendorID,
hdsl2ShdslInvVendorModelNumber,
hdsl2ShdslInvVendorSerialNumber,
hdsl2ShdslInvVendorEOCSoftwareVersion,
hdsl2ShdslInvStandardVersion,
hdsl2ShdslInvVendorListNumber,
hdsl2ShdslInvVendorIssueNumber,
hdsl2ShdslInvVendorSoftwareVersion,
hdsl2ShdslInvEquipmentCode,
hdsl2ShdslInvVendorOther
}
STATUS current
DESCRIPTION
"This group supports objects that provide unit inventory
information about the units in HDSL2/SHDSL lines."
::= { hdsl2ShdslGroups 5 }
hdsl2ShdslEndpointConfGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslEndpointCurrAtn
}
STATUS current
DESCRIPTION
"This group supports objects for configuring parameters for
segment endpoints in HDSL2/SHDSL lines."
::= { hdsl2ShdslGroups 6 }
hdsl2ShdslEndpointCurrGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslEndpointCurrAtn,
hdsl2ShdslEndpointCurrSnrMgn,
hdsl2ShdslEndpointCurrStatus,
hdsl2ShdslEndpointES,
hdsl2ShdslEndpointSES,
hdsl2ShdslEndpointCRCanomalies,
hdsl2ShdslEndpointLOSWS,
hdsl2ShdslEndpointUAS,
hdsl2ShdslEndpointCurr15MinTimeElapsed,
hdsl2ShdslEndpointCurr15MinES,
hdsl2ShdslEndpointCurr15MinSES,
hdsl2ShdslEndpointCurr15MinCRCanomalies,
hdsl2ShdslEndpointCurr15MinLOSWS,
hdsl2ShdslEndpointCurr15MinUAS,
hdsl2ShdslEndpointCurr1DayTimeElapsed,
hdsl2ShdslEndpointCurr1DayES,
hdsl2ShdslEndpointCurr1DaySES,
Ray & Abbi Standards Track [Page 57]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
hdsl2ShdslEndpointCurr1DayCRCanomalies,
hdsl2ShdslEndpointCurr1DayLOSWS,
hdsl2ShdslEndpointCurr1DayUAS
}
STATUS current
DESCRIPTION
"This group supports objects which provide current status and
performance measurements relating to segment endpoints in
HDSL2/SHDSL lines."
::= { hdsl2ShdslGroups 7 }
hdsl2Shdsl15MinIntervalGroup OBJECT-GROUP
OBJECTS
{
hdsl2Shdsl15MinIntervalES,
hdsl2Shdsl15MinIntervalSES,
hdsl2Shdsl15MinIntervalCRCanomalies,
hdsl2Shdsl15MinIntervalLOSWS,
hdsl2Shdsl15MinIntervalUAS
}
STATUS current
DESCRIPTION
"This group supports objects which maintain historic
performance measurements relating to segment endpoints in
HDSL2/SHDSL lines in 15-minute intervals."
::= { hdsl2ShdslGroups 8 }
hdsl2Shdsl1DayIntervalGroup OBJECT-GROUP
OBJECTS
{
hdsl2Shdsl1DayIntervalMoniSecs,
hdsl2Shdsl1DayIntervalES,
hdsl2Shdsl1DayIntervalSES,
hdsl2Shdsl1DayIntervalCRCanomalies,
hdsl2Shdsl1DayIntervalLOSWS,
hdsl2Shdsl1DayIntervalUAS
}
STATUS current
DESCRIPTION
"This group supports objects which maintain historic
performance measurements relating to segment endpoints in
HDSL2/SHDSL lines in 1-day intervals."
::= { hdsl2ShdslGroups 9 }
hdsl2ShdslMaintenanceGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslMaintLoopbackConfig,
Ray & Abbi Standards Track [Page 58]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
hdsl2ShdslMaintTipRingReversal,
hdsl2ShdslMaintPowerBackOff,
hdsl2ShdslMaintSoftRestart,
hdsl2ShdslMaintLoopbackTimeout,
hdsl2ShdslMaintUnitPowerSource
}
STATUS current
DESCRIPTION
"This group supports objects that provide support for
maintenance actions for HDSL2/SHDSL lines."
::= { hdsl2ShdslGroups 10 }
hdsl2ShdslEndpointAlarmConfGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslEndpointAlarmConfProfile,
hdsl2ShdslEndpointThreshLoopAttenuation,
hdsl2ShdslEndpointThreshSNRMargin,
hdsl2ShdslEndpointThreshES,
hdsl2ShdslEndpointThreshSES,
hdsl2ShdslEndpointThreshCRCanomalies,
hdsl2ShdslEndpointThreshLOSWS,
hdsl2ShdslEndpointThreshUAS,
hdsl2ShdslEndpointAlarmConfProfileRowStatus
}
STATUS current
DESCRIPTION
"This group supports objects that allow configuration of alarm
thresholds for various performance parameters for HDSL2/SHDSL
lines."
::= { hdsl2ShdslGroups 11 }
hdsl2ShdslNotificationGroup NOTIFICATION-GROUP
NOTIFICATIONS
{
hdsl2ShdslLoopAttenCrossing,
hdsl2ShdslSNRMarginCrossing,
hdsl2ShdslPerfESThresh,
hdsl2ShdslPerfSESThresh,
hdsl2ShdslPerfCRCanomaliesThresh,
hdsl2ShdslPerfLOSWSThresh,
hdsl2ShdslPerfUASThresh,
hdsl2ShdslSpanInvalidNumRepeaters,
hdsl2ShdslLoopbackFailure,
hdsl2ShdslpowerBackoff,
hdsl2ShdsldeviceFault,
hdsl2ShdsldcContinuityFault,
hdsl2ShdslconfigInitFailure,
Ray & Abbi Standards Track [Page 59]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
hdsl2ShdslprotocolInitFailure,
hdsl2ShdslnoNeighborPresent,
hdsl2ShdslLocalPowerLoss
}
STATUS current
DESCRIPTION
"This group supports notifications of significant conditions
associated with HDSL2/SHDSL lines."
::= { hdsl2ShdslGroups 12 }
hdsl2ShdslSpanConfProfileGroup OBJECT-GROUP
OBJECTS
{
hdsl2ShdslSpanConfWireInterface,
hdsl2ShdslSpanConfMinLineRate,
hdsl2ShdslSpanConfMaxLineRate,
hdsl2ShdslSpanConfPSD,
hdsl2ShdslSpanConfTransmissionMode,
hdsl2ShdslSpanConfRemoteEnabled,
hdsl2ShdslSpanConfPowerFeeding,
hdsl2ShdslSpanConfCurrCondTargetMarginDown,
hdsl2ShdslSpanConfWorstCaseTargetMarginDown,
hdsl2ShdslSpanConfCurrCondTargetMarginUp,
hdsl2ShdslSpanConfWorstCaseTargetMarginUp,
hdsl2ShdslSpanConfUsedTargetMargins,
hdsl2ShdslSpanConfReferenceClock,
hdsl2ShdslSpanConfLineProbeEnable,
hdsl2ShdslSpanConfProfileRowStatus
}
STATUS current
DESCRIPTION
"This group supports objects that constitute configuration
profiles for configuring span related parameters in SHDSL
lines."
::= { hdsl2ShdslGroups 13 }
END
Blocking unauthorized access to the HDSL2-SHDSL MIB via the element
management system is outside the scope of this document. It should
be noted that access to the MIB permits the unauthorized entity to
modify the profiles (section 6.4) such that both subscriber service
and network operations can be interfered with. Subscriber service
can be altered by modifying any of a number of service
characteristics such as rate partitioning and maximum transmission
rates. Network operations can be impacted by modification of
notification thresholds such as SES thresholds.
Ray & Abbi Standards Track [Page 60]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
There are a number of managed objects in this MIB that may be
considered to contain sensitive information. Access to these objects
would allow an intruder to obtain information about which vendor's
equipment is in use on the network. Further, such information is
considered sensitive in many environments for competitive reasons.
These identifying objects in the inventory group are:
- hdsl2ShdslInvVendorID
- hdsl2ShdslInvVendorModelNumber
- hdsl2ShdslInvVendorSerialNumber
- hdsl2ShdslInvVendorEOCSoftwareVersion
- hdsl2ShdslInvStandardVersion
- hdsl2ShdslInvVendorListNumber
- hdsl2ShdslInvVendorIssueNumber
- hdsl2ShdslInvVendorSoftwareVersion
- hdsl2ShdslInvEquipmentCode
- hdsl2ShdslInvVendorOther
- hdsl2ShdslInvTransmissionModeCapability
Therefore, it may be important in some environments to control read
access to these objects and possibly to even encrypt the values of
these object when sending them over the network via SNMP. Not all
versions of SNMP provide features for such a secure environment.
It is recommended that the implementors consider the security
features as provided by the SNMPv3 framework. Specifically, the use
of the User-based Security Model RFC 2574 [12] and the View-based
Access Control Model RFC 2575 [15] are recommended.
It is then the customer/user's responsibility to ensure that the SNMP
entity giving access to an instance of this MIB, is properly
configured to give access to those objects only to those principals
(users) that have legitimate rights to access them.
HDSL2-SHDSL layer connectivity from the xtuR will permit the
subscriber to manipulate both the HDSL2-SHDSL link directly and the
HDSL2-SHDSL embedded operations channel (EOC) for their own loop.
For example, unchecked or unfiltered fluctuations initiated by the
subscriber could generate sufficient notifications to potentially
overwhelm either the management interface to the network or the
element manager.
It should be noted that interface indices in this MIB are maintained
persistently. VACM data relating to these should be stored
persistently.
Ray & Abbi Standards Track [Page 61]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
There are a number of management objects defined in this MIB that
have a MAX-ACCESS clause of read-write and/or read-create. Such
objects may be considered sensitive or vulnerable in some network
environments. The support for SET operations in a non-secure
environment without proper protection can have a negative effect on
network operations.
The authors are deeply grateful to the authors of the ADSL LINE MIB
(RFC 2662 [23]), Gregory Bathrick and Faye Ly, as much of the text
and structure of this document originates in their documents.
The authors are also grateful to the authors of FR MFR MIB (RFC 3020
[24]), Prayson Pate, Bob Lynch, and Kenneth Rehbehn, as the majority
of the Security Considerations section was lifted from their
document.
The authors also acknowledge the importance of the contributions and
suggestions regarding interface indexing structures received from
David Horton of CITR.
Other contributions were received from the following:
Philip Bergstresser (Adtran)
Steve Blackwell (Centillium)
Umberto Bonollo (NEC Australia)
Yagal Hachmon (RAD)
Mark Johnson (Red Point)
Sharon Mantin (Orckit)
Moti Morgenstern (ECI)
Raymond Murphy (Ericsson)
Lee Nipper (Verilink)
Randy Presuhn (BMC Software)
Katy Sherman (Orckit)
Mike Sneed (ECI)
Jon Turney (DSL Solutions)
Aron Wahl (Memotec)
Bert Wijnen (Lucent)
Michael Wrobel (Memotec)
Ray & Abbi Standards Track [Page 62]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
[1] Harrington, D., Presuhn, R. and B. Wijnen, "An Architecture for
Describing SNMP Management Frameworks", RFC 2571, April 1999.
[2] Rose, M. and K. McCloghrie, "Structure and Identification of
Management Information for TCP/IP-based Internets", STD 16, RFC
1155, May 1990.
[3] Rose, M. and K. McCloghrie, "Concise MIB Definitions", STD 16,
RFC 1212, March 1991.
[4] Rose, M., "A Convention for Defining Traps for use with the
SNMP", RFC 1215, March 1991.
[5] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose,
M. and S. Waldbusser, "Structure of Management Information
Version 2 (SMIv2)", STD 58, RFC 2578, April 1999.
[6] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose,
M. and S. Waldbusser, "Textual Conventions for SMIv2", STD 58,
RFC 2579, April 1999.
[7] McCloghrie, K., Perkins, D., Schoenwaelder, J., Case, J., Rose,
M. and S. Waldbusser, "Conformance Statements for SMIv2", STD
58, RFC 2580, April 1999.
[8] Case, J., Fedor, M., Schoffstall, M. and J. Davin, "Simple
Network Management Protocol", STD 15, RFC 1157, May 1990.
[9] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser,
"Introduction to Community-based SNMPv2", RFC 1901, January
1996.
[10] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser,
"Transport Mappings for Version 2 of the Simple Network
Management Protocol (SNMPv2)", RFC 1906, January 1996.
[11] Case, J., Harrington D., Presuhn, R. and B. Wijnen, "Message
Processing and Dispatching for the Simple Network Management
Protocol (SNMP)", RFC 2572, April 1999.
[12] Blumenthal, U. and B. Wijnen, "User-based Security Model (USM)
for version 3 of the Simple Network Management Protocol
(SNMPv3)", RFC 2574, April 1999.
Ray & Abbi Standards Track [Page 63]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
[13] Case, J., McCloghrie, K., Rose, M. and S. Waldbusser, "Protocol
Operations for Version 2 of the Simple Network Management
Protocol (SNMPv2)", RFC 1905, January 1996.
[14] Levi, D., Meyer, P. and B. Stewart, "SNMPv3 Applications", RFC
2573, April 1999.
[15] Wijnen, B., Presuhn, R. and K. McCloghrie, "View-based Access
Control Model (VACM) for the Simple Network Management Protocol
(SNMP)", RFC 2575, April 1999.
[16] Case, J., Mundy, R., Partain, D. and B. Stewart, "Introduction
to Version 3 of the Internet-standard Network Management
Framework", RFC 2570, April 1999.
[17] Bradner, S., "Key Words for use in RFCs to Indicate Requirement
Levels", BCP 14, RFC 2119, March 1997.
[18] American National Standards Institute, ANSI T1E1.4/2000-006,
February 2000.
[19] Blackwell, S., Editor, "Single-Pair High-Speed Digital
Subscriber Line (SHDSL) Transceivers", ITU-T Draft G.991.2,
April 2000.
[20] McCloghrie, K. and M. Rose, M., "Management Information Base
for Network Management of TCP/IP-based internets: MIB-II", STD
17, RFC 1213, March 1991.
[21] McCloghrie, K. and F. Kastenholz, "The Interfaces Group MIB",
RFC 2863, June 2000.
[22] Tesink, K., "Textual Conventions for MIB Modules Using
Performance History Based on 15 Minute Intervals", RFC 2493,
January 1999.
[23] Bathrick, G. and F. Ly, "Definitions of Managed Objects for the
ADSL Lines", RFC 2662, August 1999.
[24] Pate, P., Lynch, B. and K. Rehbehn, "Definitions of Managed
Objects for Monitoring and Controlling the UNI/NNI Multilink
Frame Relay Function", RFC 3020, December 2000.
[25] American National Standards Institute, "Coded Identification of
Equipment Entities of the North American Telecommunications
System for the Purpose of Information Exchange", T1.213-2001.
Ray & Abbi Standards Track [Page 64]
RFC 3276 HDSL2-SHDSL-LINE MIB May 2002
The IETF takes no position regarding the validity or scope of any
intellectual property or other rights that might be claimed to
pertain to the implementation or use of the technology described in
this document or the extent to which any license under such rights
might or might not be available; neither does it represent that it
has made any effort to identify any such rights. Information on the
IETF's procedures with respect to rights in standards-track and
standards-related documentation can be found in BCP-11. Copies of
claims of rights made available for publication and any assurances of
licenses to be made available, or the result of an attempt made to
obtain a general license or permission for the use of such
proprietary rights by implementors or users of this specification can
be obtained from the IETF Secretariat.
The IETF invites any interested party to bring to its attention any
copyrights, patents or patent applications, or other proprietary
rights which may cover technology that may be required to practice
this standard. Please address the information to the IETF Executive
Director.
Copyright (C) The Internet Society (2002). All Rights Reserved.
This document and translations of it may be copied and furnished to
others, and derivative works that comment on or otherwise explain it
or assist in its implementation may be prepared, copied, published
and distributed, in whole or in part, without restriction of any
kind, provided that the above copyright notice and this paragraph are
included on all such copies and derivative works. However, this
document itself may not be modified in any way, such as by removing
the copyright notice or references to the Internet Society or other
Internet organizations, except as needed for the purpose of
developing Internet standards in which case the procedures for
copyrights defined in the Internet Standards process must be
followed, or as required to translate it into languages other than
English.
The limited permissions granted above are perpetual and will not be
revoked by the Internet Society or its successors or assigns.
This document and the information contained herein is provided on an
"AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING
TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION
HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Acknowledgement
Funding for the RFC Editor function is currently provided by the
Internet Society.
Ray & Abbi Standards Track [Page 66]