Network Working Group T. Brown
Request for Comments: 1595 K. Tesink
Category: Standards Track Editors
Bell Communications Research
March 1994
Definitions of Managed Objects
for the SONET/SDH Interface Type
Status of this Memo
This document specifies an Internet standards track protocol for the
Internet community, and requests discussion and suggestions for
improvements. Please refer to the current edition of the "Internet
Official Protocol Standards" (STD 1) for the standardization state
and status of this protocol. Distribution of this memo is unlimited.
Abstract
This memo defines a portion of the Management Information Base (MIB)
for use with network management protocols in TCP/IP-based internets.
In particular, it defines objects for managing Synchronous Optical
Network/Synchronous Digital Hierarchy (SONET/SDH) objects. This
document is a companion document with Definitions of Managed Objects
for the DS1/E1 and DS3/E3 Interface Types, RFC1406 [14] and RFC1407
[13].
This memo specifies a MIB module in a manner that is both compliant
to the SNMPv2 SMI, and semantically identical to the peer SNMPv1
definitions.
Table of Contents
1. The SNMPv2 Network Management Framework ............... 22. Objects ............................................... 32.1 Format of Definitions ................................ 33. Overview .............................................. 43.1 Use of the ifTable ................................... 43.2 Use of ifTable for SONET/SDH Medium/Section/Line
Layer ................................................ 63.3 Use of ifTable for SONET/SDH Paths. .................. 73.4 Use of ifTable for SONET/SDH VTs/VCs ................. 83.5 SONET/SDH Terminology ................................ 93.6 Values for x for the Section, Line, Path, and VT
Layers ............................................... 164. Object Definitions .................................... 174.1 The SONET/SDH Medium Group ........................... 18
AToM MIB Working Group [Page 1]
RFC 1595 SONET/SDH Objects March 1994
4.2 The SONET/SDH Section Group .......................... 214.2.1 The SONET/SDH Section Current Group ................ 214.2.2 The SONET/SDH Section Interval Group ............... 234.3 The SONET/SDH Line Group ............................. 254.3.1 The SONET/SDH Line Current Group ................... 254.3.2 The SONET/SDH Line Interval Group .................. 274.4 The SONET/SDH Far End Line Group ..................... 304.4.1 The SONET/SDH Far End Line Current Group ........... 304.4.2 The SONET/SDH Far End Line Interval Group .......... 324.5 The SONET/SDH Path Group ............................. 344.5.1 The SONET/SDH Path Current Group ................... 344.5.2 The SONET/SDH Path Interval Group .................. 374.6 The SONET/SDH Far End Path Group ..................... 394.6.1 The SONET/SDH Far End Path Current Group ........... 394.6.2 The SONET/SDH Far End Path Interval Group .......... 414.7 The SONET/SDH Virtual Tributary Group ................ 434.7.1 The SONET/SDH VT Current Group ..................... 434.7.2 The SONET/SDH VT Interval Group .................... 464.8 The SONET/SDH Far End VT Group ....................... 484.8.1 The SONET/SDH Far End VT Current Group ............. 484.8.2 The SONET/SDH Far End VT Interval Group ............ 504.9 Conformance Information .............................. 524.10 Compliance Statements ............................... 525. Acknowledgments ....................................... 566. References ............................................ 577. Security Considerations ............................... 598. Authors' Addresses .................................... 59
The SNMPv2 Network Management Framework consists of four major
components. They are:
RFC 1442 [1] which defines the SMI, the mechanisms used for
describing and naming objects for the purpose of management.
STD 17, RFC 1213 [6] defines MIB-II, the core set of managed
objects for the Internet suite of protocols. Reference [12]
defines the evolution of the Interfaces Group of MIB II in terms
of extensions and precise applications of the objects.
RFC 1445 [4] which defines the administrative and other
architectural aspects of the framework.
RFC 1448 [5] which defines the protocol used for network access to
managed objects.
AToM MIB Working Group [Page 2]
RFC 1595 SONET/SDH Objects March 1994
The Framework permits new objects to be defined for the purpose of
experimentation and evaluation.
This specification makes also use of:
RFC 1443 [2] which defines textual conventions for the
specification of managed objects.
RFC 1444 [3] which defines conformance statements for the
specification of managed objects.
Managed objects are accessed via a virtual information store, termed
the Management Information Base or MIB. Objects in the MIB are
defined using the subset of Abstract Syntax Notation One (ASN.1) [7]
defined in the SMI. In particular, each object has a name, a syntax,
and an encoding. The name is an object identifier, an
administratively assigned name, which specifies an object type. The
object type together with an object instance serves to uniquely
identify a specific instantiation of the object. For human
convenience, we often use a textual string, termed the OBJECT
DESCRIPTOR, to also refer to the object type.
The syntax of an object type defines the abstract data structure
corresponding to that object type. The ASN.1 language is used for
this purpose. However, the SMI RFC 1442 purposely restricts the
ASN.1 constructs which may be used. These restrictions are
explicitly made for simplicity.
The encoding of an object type is simply how that object type is
represented using the object type's syntax. Implicitly tied to the
notion of an object type's syntax and encoding is how the object type
is represented when being transmitted on the network. The SMI
specifies the use of the basic encoding rules of ASN.1 [8], subject
to the additional requirements imposed by the SNMP.
Section 4 contains contains the specification of all object types
contained in this MIB module. The object types are defined using the
conventions defined in the SMI, as amended by the extensions
specified in the SNMPv2 SMI.
AToM MIB Working Group [Page 3]
RFC 1595 SONET/SDH Objects March 1994
These objects are used when the particular media being used to
realize an interface is a SONET/SDH interface. At present, this
applies to these values of the ifType variable in the Internet-
standard MIB:
sonet (39), sonetPath (50), sonetVT (51)
The definitions contained herein are based on the SONET/SDH
specifications in ANSI T1.105 and T1.106-1988 [9, 9a, 10] and CCITT
G.707, 708, 709, and G.783 [15-18].
This section specifies how the MIB II interfaces group, as defined in
[12], is used for SONET/SDH interfaces. The SONET/SDH layers support
several multiplexing possibilities.
For example in SONET, an Synchronous Transport Signal 3 (STS-3) has 3
SONET Paths, and a STS-3c has 1 SONET Path. Another example could be
a STS-12 having 4 SONET STS-3c Paths. Similarly, a SONET Synchronous
Payload Envelope (SPE) can carry many Virtual Tributaries (VTs), for
example, one SONET SPE can carry 28 VT1.5s. It is important to note
that an SPE and a VT in SONET is collectively referred to as a
Virtual Container (VC) in SDH. Also, an STS is called Synchronous
Transport Module (STM) in SDH.
Not all SONET/SDH equipment terminate all SONET/SDH layers. For
example, an SONET/SDH STE regenerator terminates SONET/SDH Sections
only, and is transparent for all layers above that. SONET/SDH Add-
Drop multiplexers and Digital Cross Connect Systems terminate
SONET/SDH Lines. SONET/SDH Terminal Multiplexers may also terminate
SONET/SDH Paths and VTs/VCs.
MIB II [6], as extended by [12], accommodates these cases by
appropriate use of the MIB II system group, and the interfaces group.
The system group can name and describe the type of managed resource.
The interfaces group defines which SONET/SDH layers apply, how these
layers are configured and multiplexed. This is achieved by proper
representation of SONET/SDH Layers by ifEntries as defined in [12],
as follows:
AToM MIB Working Group [Page 4]
RFC 1595 SONET/SDH Objects March 1994
_____________________________
| | | | >
| | | | |
| VT 1 |..........|VT K| > K ifEntries
| | | | |
|_____________|__________|____| >
| | | | >
| | | | |
| Path 1 |......|Path L| > L ifEntries
| | | | |
|_______________|______|______| >
| | >
| | |
| Line | |
| | |
|_____________________________| |
| | |
| | |
| Section Layer | > 1 ifEntry
| | |
|_____________________________| |
| | |
| | |
| Physical Medium Layer | |
| | |
|_____________________________| >
Use of ifTable for a SONET/SDH port
The exact configuration and multiplexing of the layers is maintained
in the ifStackTable [12].
AToM MIB Working Group [Page 5]
RFC 1595 SONET/SDH Objects March 1994
Only the ifGeneralGroup needs to be supported.
ifTable Object Use for combined SONET/SDH Medium/Section/Line Layer
======================================================================
ifIndex Interface index.
ifDescr SONET/SDH Medium/Section/Line
ifType sonet(39)
ifSpeed Speed of line rate for SONET/SDH,
(e.g., 155520000 bps).
ifPhysAddress The value of the Circuit Identifier.
If no Circuit Identifier has been assigned
this object should have an octet string with
zero length.
ifAdminStatus Supports read-only access.
The desired administrative status of the
interface.
ifOperStatus The value testing(3) is not used.
This object assumes the value down(2),
if the objects sonetSectionCurrentStatus
and sonetLineCurrentStatus have
any other value than sonetSectionNoDefect(1)
and sonetLineNoDefect(1), respectively.
ifLastChange sysUpTime at the last change in
ifOperStatus.
ifName Textual name of the interface or an
OCTET STRING of zero length.
ifLinkUpDownTrapEnable Set to enabled(1).
Supports read-only access.
ifHighSpeed Speed of line in Mega-bits per second
(e.g., 155 Mbps)
ifConnectorPresent Set to true(1).
AToM MIB Working Group [Page 6]
RFC 1595 SONET/SDH Objects March 1994
Only the ifGeneralGroup needs to be supported.
ifTable Object Use for SONET/SDH Paths
=========================================
ifIndex Interface index.
ifDescr SONET/SDH Path
ifType sonetPath(50)
ifSpeed set to speed of SONET/SDH path
(e.g., an STS-1 path has a
rate of 50112000 bps.)
ifPhysAddress Circuit Identifier or OCTET STRING of
zero length.
ifAdminStatus Supports read-only access.
The desired administrative status of the
interface.
ifOperStatus This object assumes the value down(2),
if the object sonetPathCurrentStatus has
any other value than sonetPathNoDefect(1).
ifLastChange sysUpTime at the last change in ifOperStatus.
ifName Textual name of the interface or an
OCTET STRING of zero length.
ifLinkUpDownTrapEnable Default value is disabled(2).
Just read-only access may be
supported.
ifHighSpeed Set to rate of SONET/SDH path
in Mega-bits per second.
ifConnectorPresent Set to false(2).
AToM MIB Working Group [Page 7]
RFC 1595 SONET/SDH Objects March 1994
Only the ifGeneralGroup needs to be supported.
ifTable Object Use for SONET/SDH VTs/VCs
===========================================
ifIndex Interface index.
ifDescr SONET/SDH VT/VC
ifType sonetVT(51)
ifSpeed Set to speed of VT/VC
(e.g., a VT1.5 has a rate of
1728000 bps.)
ifPhysAddress Circuit Identifier or OCTET STRING of
zero length.
ifAdminStatus Supports read-only access.
The desired administrative status of the
interface.
ifOperStatus This object assumes the value down(2),
if the object sonetVTCurrentStatus has
any other value than sonetVTNoDefect(1).
ifLastChange sysUpTime at the last change in
ifOperStatus.
ifName Textual name of the interface or an
OCTET STRING of zero length.
ifLinkUpDownTrapEnable Default value is disabled(2).
Just read-only access may be
supported.
ifHighSpeed Set to rate of VT in Mega-bits per second.
ifConnectorPresent Set to false(2).
AToM MIB Working Group [Page 8]
RFC 1595 SONET/SDH Objects March 1994
The terminology used in this document to describe error conditions on
a SONET circuit as monitored by a SONET system are from the ANSI
T1M1.3/93-005R2 [11]. The terminology used in this document to
describe error conditions on a SDH circuit as monitored by a SDH
system are from the CCITT G.783 [18]. Only the SONET Performance
Monitoring terminology is defined in this document. The definitions
for SDH Performance Monitoring terms are similar but not identical,
and they can be found in [18]. If the definition in this document
does not match the definition in the ANSI T1M1.3/93-005R2 draft
document, the implementer should follow the definition described in
this document.
Section Loss Of Frame Failure (Out of Frame Event, Severely
Errored Frame Defect)
An Out of Frame (OOF) event (or Severely Errored Frame
defect) is the occurrence of four contiguous errored
frame alignment words. A frame alignment work occupies
the A1 and A2 bytes of an STS frame, and is defined in
T1.105. The SEF defect is terminated when two contiguous
error-free frame words are detected. Any implementation
of the frame recovery circuitry which achieves
realignment following an OOF within the 250 microsecond
(two frames) interval implied by this definition is
acceptable.
An Loss of Frame (LOF) defect is declared when an OOF/SEF
defect persists for a period of 3 milliseconds. The LOF
defect is terminated when the incoming signal remains
continuously in-frame for a period of 1 ms to 3 ms.
An LOF failure is declared when the LOF defect persists
for a period of 2.5 +/- 0.5 seconds, except when an LOS
defect or failure is present. The LOF failure is cleared
when the LOS failure is declared, or when the LOF defect
is absent for 10 +/- 0.5 seconds.
Loss of Signal
The Loss of Signal (LOS) defect is declared when no
transitions are detected on the incoming signal (before
descrambling). The LOS defect is detected upon
observing 2.3 to 100 microseconds of no transitions. The
LOS defect is cleared after a 125 microsecond interval
(one frame) during which no LOS defect is detected.
The LOS failure is declared when the LOS defect persists
for a period of 2.5 +/- 0.5 seconds, or if LOS defect is
AToM MIB Working Group [Page 9]
RFC 1595 SONET/SDH Objects March 1994
present when the criteria for LOF failure declaration
have been met. The LOS failure is cleared when the LOS
defect is absent for a period of 10 +/- 0.5 seconds.
Declaration of LOS failure clears any existing LOF
failure. Clearing the LOS failure allows immediate
declaration of the LOF failure if conditions warrant.
STS-Path Loss of Pointer
An Loss of Pointer (LOP) defect is declared when either a
valid pointer is not detected in eight consecutive
frames, or when eight consecutive frames are detected
with the New Data Flag (NDF) set to "1001" without a
valid concatenation indicator (see ANSI T1.105). A LOP
defect is terminated when either a valid pointer with a
normal NDF set to "0110", or a valid concatenation
indicator is detected for three contiguous frames.
Incoming STS-Path AIS shall not result in the declaration
of a LOP defect.
A STS-Path LOP failure is declared when the STS-Path LOP
defect persists for a period of 2.5 +/- 0.5 seconds. A
STS-Path LOP failure is cleared when the STS-Path LOP
defect is absent for 10 +/- 0.5 seconds.
VT Loss of Pointer
A VT LOP defect is declared when either a valid pointer
is not detected in eight consecutive VT superframes, or
when eight consecutive VT superframes are detected with
the NDF set to "1001" without a valid concatenation
indicator. A VT LOP defect is terminated when either a
valid pointer with a normal NDF set to "0110", or a valid
concatenation indicator is detected for three contiguous
VT superframes. Incoming VT-Path AIS shall not result in
declaring a VT LOP defect.
A VT LOP failure is declared when the VT LOP defect
persists for 2.5 +/- 0.5 seconds. A VT LOP failure is
cleared when the VT LOP defect is absent for 10 +/- 0.5
seconds.
Line Alarm Indication Signal
A Line Alarm Indication Signal (L-AIS) is defined in ANSI
T1.105. The following criteria are specific to the L-AIS
defect:
-- Line AIS defect is detected as a "111" pattern in
bits 6, 7, and 8 of the K2 byte in five consecutive
frames.
AToM MIB Working Group [Page 10]
RFC 1595 SONET/SDH Objects March 1994
-- Line AIS defect is terminated when bits 6, 7, and 8
of the K2 byte do not contain the code "111" for five
consecutive frames.
A Line AIS failure is declared when the Line AIS defect
persists for a period of 20.5 +/- 0.5 seconds. A Line
AIS failure is cleared when the Line AIS defect is absent
for 10 +/- 0.5 seconds.
STS-Path Alarm Indication Signal
The STS-Path Alarm Indication Signal (AIS) is defined in
ANSI T1.105 as all ones in bytes H1, H2, and H3 as well
as all ones in the entire STS SPE. The following
criteria are specific to the STS-Path AIS defect:
-- STS-Path AIS defect is detected as all ones in bytes
H1 and H2 in three contiguous frames.
-- The STS-Path AIS defect is terminated when a valid STS
Pointer is detected with the NDF set to "1001" (inverted)
for one frame, or "0110" (normal) for three contiguous
frames.
A STS-Path AIS failure is declared when the STS-Path AIS
defect persists for 2.5 +/- 0.5 seconds. A STS-Path AIS
failure is cleared when the STS-Path AIS defect is absent
for 10 +/- 0.5 seconds.
VT-Path Alarm Indication Signal
The VT-Path Alarm Indication Signal (AIS) is only
applicable for VTs in the floating mode of operation.
VT-Path AIS is used to alert the downstream VT Path
Terminating Entity (PTE) of an upstream failure. Upon
detection of a failure, Line AIS, or STS-Path AIS, an STS
PTE will generate downstream VT-Path AIS if the STS
Synchronous Payload Envelope (SPE) is carrying floating
VTs. VT-Path AIS is specified in ANSI T1.105 as all ones
in bytes V1, V2, V3, and V4, as well as all ones in the
entire VT SPE. The following criteria are specific to
VT-Path AIS defect:
-- VT-Path AIS defect is detected by a VT PTE as all
ones in bytes V1 and V2 in three contiguous VT
superframes.
-- VT-Path AIS defect is terminated when valid VT
pointer with a valid VT size is detected with the NDF set
to "1001" (inverted) for one VT superframe, or "0110"
AToM MIB Working Group [Page 11]
RFC 1595 SONET/SDH Objects March 1994
(normal) for three contiguous VT superframes are
detected.
A VT-Path AIS failure is declared when the VT-Path AIS
defect persists for 2.5 +/- 0.5 seconds. A VT-Path AIS
failure is cleared when the VT-Path AIS defect is absent
for 10 +/- 0.5 seconds.
Line Remote Defect Indication
Line Remote Defect Indication (RDI) (aka Line FERF)
signal is the occurrence of a "110" pattern in bit
positions 6, 7, and 8 of the K2 byte in STS-1 #1 of the
STS-N signal. Line RDI is defined in ANSI T1.105. The
following criteria are specific to Line RDI defect:
-- Line RDI defect is a "110" code in bits 6, 7, and 8
of the K2 byte of in STS-1 #1 in five consecutive frames.
-- Line RDI defect is terminated when any code other
than "110" is detected in bits 6, 7, and 8 of the K2 byte
in five consecutive frames.
A Line Remote Failure Indication (RFI) failure is
declared when the incoming Line RDI defects lasts for 2.5
+/- 0.5 seconds. The Line RFI failure is cleared when no
Line RDI defects are detected for 10 +/- 0.5 seconds.
STS-Path Remote Defect Indication
STS-Path RDI (aka STS-Path FERF) signal shall be
generated within 100 milliseconds by the STS PTE upon
detection of an AIS or LOP defect. Transmission of the
STS-Path RDI signal shall cease within 100 milliseconds
when the STS PTE no longer detects STS-Path AIS or STS-
Path LOP defect. The STS-Path RDI shall accurately
report the presence or absence of STS-Path AIS or STS-
Path LOP defects. STS-Path RDI defect is defined in ANSI
T1.105. The following requirements are specific to the
STS-Path RDI defect:
-- STS-Path RDI is detected by all STS PTEs. STS-Path
RDI is detected by the upstream STS PTE as a "1" in bit
five of the Path Status byte (G1) for five contiguous
frames.
-- Removal of STS-Path Remote Defect Indication is
detected by a "0" in bit 5 of the G1 byte in five
contiguous frames.
AToM MIB Working Group [Page 12]
RFC 1595 SONET/SDH Objects March 1994
A STS-Path Remote Failure Indication (RFI) failure is
declared when the incoming STS-Path RDI defects lasts for
2.5 +/- 0.5 seconds. The STS-Path RFI failure is cleared
when no STS-Path RDI defects are detected for 10 +/- 0.5
seconds.
VT-Path Remote Defect Indication
VT Path RDI (aka VT Path FERF) signal shall be generated
within 100 milliseconds by the VT PTE upon detection of a
VT-Path AIS or LOP defect. Transmission of the VT-Path
RDI signal shall cease within 100 milliseconds when the
VT PTE no longer detects VT-Path AIS or VT-Path LOP
defect. The VT-Path RDI shall accurately report the
presence or absence of VT-Path AIS or VT-Path LOP
defects. VT-Path RDI defect is defined in ANSI T1.105.
The following requirements are specific to VT-Path RDI
defect:
-- VT-Path RDI defect is the occurrence of a "1" in bit
4 of the VT-Path Overhead byte (V5) in five contiguous
frames.
-- VT-Path RDI defect is terminated when a "0" is
detected in bit 4 of the VT-Path Overhead byte (V5) for
five contiguous frames.
A VT-Path Remote Failure Indication (RFI) (derived)
failure is declared when the incoming VT-Path RDI defects
lasts for 2.5 +/- 0.5 seconds. The VT-Path RFI failure
is cleared when no VT-Path RDI defects are detected for
10 +/- 0.5 seconds.
VT-Path Remote Failure Indication
The VT-Path RFI signal is only required for the case of
byte synch mapped DS1s where the DS1 frame bit is not
mapped. The VT-Path RFI is specified in ANSI T1.105,
where it is currently called VT path yellow. When
provided, the VT-Path RFI signal is used to indicate the
occurrence of far-end failures. When the VT-Path RFI is
not provided, far-end failures are derived from local
timing of the VT-Path RDI defect. The VT-Path RFI
failure is declared within 5 ms of detecting the incoming
VT-Path RFI Signal. The VT-Path Remote Failure
Indication (RFI) failure is cleared within 50 ms of
detecting the removal of the incoming VT-Path RFI signal.
AToM MIB Working Group [Page 13]
RFC 1595 SONET/SDH Objects March 1994
Coding Violation
Coding Violations (CV) are Bit Interleaved Parity (BIP)
errors that are detected in the incoming signal. CV
counters are incremented for each BIP error detected.
That is, each BIP-8 can detect up to eight errors per
STS-N frame, with each error incrementing the CV counter.
Section CVs shall be collected using the BIP-8 in the B1
byte located in the Section Overhead of STS-1 #1. Line
CVs shall be collected using the BIP-8s in B2 bytes
located in the Line Overhead of each STS-1 (since all CVs
on an STS-N line are counted together, this is equivalent
to counting each error in the BIP-8*N contained in the B2
bytes of the STS-N Line Overhead). Thus, on an STS-N
signal, up to 8 x N CVs may occur in each frame. Path
CVs shall be collected using the BIP-8 in the B3 byte of
the STS-Path Overhead of the STS SPE. VT CVs shall be
collected using the BIP-2 in the V5 overhead byte of the
floating VT.
Errored Seconds
At each layer, an Errored Second (ES) is a second with
one or more Coding Violations at that layer OR one or
more incoming defects (e.g., SEF, LOS, AIS, LOP) at that
layer has occurred.
Severely Errored Seconds
At each layer, an Severely Errored Second (SES) is a
second with x or more CVs at that layer, or a second
during which at least one or more incoming defects at
that layer has occurred. Values of x vary depending on
the line rate and the Bit Error Rate. See Section 3.4
for values for x.
Severely Errored Framing Seconds
A Severely Errored Framing Second (SEFS) is a seconds
with containing one or more SEF events. This counter is
only counted at the Section Layer.
Unavailable Seconds
At the Line, Path, and VT layers, an unavailable second
is calculated by counting the number of seconds that the
interface is unavailable. At each layer, the SONET/SDH
interface is said to be unavailable at the onset of 10
contiguous SESs. The 10 SESs are included in unavailable
time. Once unavailable, the SONET/SDH interface becomes
available at the onset of 10 contiguous seconds with no
SESs. The 10 seconds with no SESs are excluded from
unavailable time. With respect to the SONET/SDH error
AToM MIB Working Group [Page 14]
RFC 1595 SONET/SDH Objects March 1994
counts at each layer, all counters at that layer are
incremented while the SONET/SDH interface is deemed
available at that layer. While the interface is deemed
unavailable at that layer, the only count that is
incremented is UASs at that layer.
A special case exists when the 10 or more second period
crosses the 900 second statistics window boundary, as the
foregoing description implies that the SES and UAS
counters must be adjusted when the Unavailable Signal
State is entered. Clearly, successive GETs of the
affected sonetPathIntervalSES and sonetPathIntervalUAS
(for the Line and VT also) objects will return differing
values if the first GET occurs during the first few
seconds of the window. This is viewed as an unavoidable
side-effect of selecting the presently defined managed
objects as a basis for this memo.
Unequipped
If a Path or VT connection is not provisioned (idle) the
SONET equipment will signal this state by transmitting
the Path or VT Signal Label as follows:
- byte C2 of the STS Path Overhead equal to 0 for an
unequipped Path,
- byte V5 of the VT Path Overhead equal to 0 for an
unequipped VT.
Signal Label Mismatch
A Path or VT connection is not correctly provisioned if a
received Path or VT Signal Label mismatch occurs. A
received Signal Label is considered mismatched if it does
not equal either the locally provisioned value or the
value 'equipped non-specific' (1 hex). Note that any
received non-zero Signal Label is considered a locally
provisioned value of 'equipped non-specific'. Only in-
service, provisioned Path Terminating equipment can
detect mismatched Signal labels. It is considered
provisioned if it has been configured for a mapping and
has been assigned signals to and from which the mapping
takes place.
Circuit Identifier
This is a character string specified by the circuit
vendor, and is useful when communicating with the vendor
during the troubleshooting process.
AToM MIB Working Group [Page 15]
RFC 1595 SONET/SDH Objects March 1994
Value for x for SONET/SDH Section SES Definition
Rate x Minimum Bit Error Rate
=======================================================
OC-1 9 1.5 x 10^-7
0C-3 16 1 x 10^-7
OC-9 47 1 x 10^-7
OC-12 63 1 x 10^-7
OC-18 94 1 x 10^-7
OC-24 125 1 x 10^-7
OC-36 187 1 x 10^-7
OC-48 249 1 x 10^-7
Value for x for SONET/SDH Line SES Definition
Rate x Minimum Bit Error Rate
=======================================================
OC-1 12 2 x 10^-7
0C-3 32 2 x 10^-7
OC-9 94 2 x 10^-7
OC-12 124 2 x 10^-7
OC-18 186 2 x 10^-7
OC-24 248 2 x 10^-7
OC-36 370 2 x 10^-7
OC-48 494 2 x 10^-7
Value for x for SONET/SDH STS-Path SES Definition
Rate x Minimum Bit Error Rate
=======================================================
STS-1 9 1.5 x 10^-7
STS-3 16 1 x 10^-7
Value for x for SONET/SDH VT-Path SES Definition
Rate x Minimum Bit Error Rate
=======================================================
VT1.5 4 2 x 10^-6
VT2 6 2 x 10^-6
VT3 8 2 x 10^-6
VT6 14 2 x 10^-6
AToM MIB Working Group [Page 16]
RFC 1595 SONET/SDH Objects March 1994
SONET-MIB DEFINITIONS ::= BEGIN
IMPORTS
MODULE-IDENTITY, OBJECT-TYPE, Counter32, Gauge32,
Integer32,
FROM SNMPv2-SMI
TEXTUAL-CONVENTION, DisplayString
FROM SNMPv2-TC
MODULE-COMPLIANCE, OBJECT-GROUP
FROM SNMPv2-CONF
ifIndex, transmission
FROM RFC-1213;
-- This is the MIB module for the SMDS Interface objects.
sonetMIB MODULE-IDENTITY
LAST-UPDATED "9401030000Z"
ORGANIZATION "IETF AToM MIB Working Group"
CONTACT-INFO
" Tracy Brown
Postal: Bell Communications Research
331 Newman Springs Road
P.O. Box 7020
Red Bank, NJ 07701-7020
US
Tel: +1 908 758 2107
Fax: +1 908 758 4177
E-mail: tacox@mail.bellcore.com
Kaj Tesink
Postal: Bell Communications Research
331 Newman Springs Road
P.O. Box 7020
Red Bank, NJ 07701-7020
US
Tel: +1 908 758 5254
Fax: +1 908 758 4196
AToM MIB Working Group [Page 17]
RFC 1595 SONET/SDH Objects March 1994
E-mail: kaj@cc.bellcore.com"
DESCRIPTION
"The MIB module to describe
SONET/SDH interfaces objects."
::= { transmission 39 }
-- This is the MIB module for the SONET/SDH objects
sonetObjects OBJECT IDENTIFIER ::= { sonetMIB 1 }
sonetObjectsPath OBJECT IDENTIFIER ::= { sonetMIB 2 }
sonetObjectsVT OBJECT IDENTIFIER ::= { sonetMIB 3 }
-- groups in the SONET/SDH MIB module
sonetMedium OBJECT IDENTIFIER ::= { sonetObjects 1 }
sonetSection OBJECT IDENTIFIER ::= { sonetObjects 2 }
sonetLine OBJECT IDENTIFIER ::= { sonetObjects 3 }
sonetFarEndLine OBJECT IDENTIFIER ::= { sonetObjects 4 }
sonetPath OBJECT IDENTIFIER ::= { sonetObjectsPath 1 }
sonetFarEndPath OBJECT IDENTIFIER ::= { sonetObjectsPath 2 }
sonetVT OBJECT IDENTIFIER ::= { sonetObjectsVT 1 }
sonetFarEndVT OBJECT IDENTIFIER ::= { sonetObjectsVT 2 }
-- the SONET/SDH Medium group
-- SONET/SDH interfaces for some applications may be
-- electrical interfaces and not optical interfaces.
-- This group handles the configuration information for
-- both optical SONET/SDH interfaces and electrical
-- SONET/SDH interfaces.
sonetMediumTable OBJECT-TYPE
SYNTAX SEQUENCE OF SonetMediumEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
AToM MIB Working Group [Page 18]
RFC 1595 SONET/SDH Objects March 1994
"The SONET/SDH Medium table."
::= { sonetMedium 1 }
sonetMediumEntry OBJECT-TYPE
SYNTAX SonetMediumEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the SONET/SDH Medium table."
INDEX { ifIndex }
::= { sonetMediumTable 1 }
SonetMediumEntry ::=
SEQUENCE {
sonetMediumType INTEGER,
sonetMediumTimeElapsed Integer32,
sonetMediumValidIntervals Integer32,
sonetMediumLineCoding INTEGER,
sonetMediumLineType INTEGER,
sonetMediumCircuitIdentifier DisplayString
}
sonetMediumType OBJECT-TYPE
SYNTAX INTEGER {
sonet(1),
sdh(2)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable identifies whether a SONET
or a SDH signal is used across this interface."
::= { sonetMediumEntry 1 }
sonetMediumTimeElapsed OBJECT-TYPE
SYNTAX Integer32 (1..900)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The number of seconds, including partial
seconds, that have elapsed since the beginning of
the current error-measurement period."
::= { sonetMediumEntry 2 }
sonetMediumValidIntervals OBJECT-TYPE
SYNTAX Integer32 (0..96)
MAX-ACCESS read-only
AToM MIB Working Group [Page 19]
RFC 1595 SONET/SDH Objects March 1994
STATUS current
DESCRIPTION
"The number of previous intervals for which valid
data has been stored. A SONET device must support
at least n intervals.
The minimum value of n is 4.
The default of n is 32.
The maximum value of n is 96.
The value of this object will be n unless
the device was brought online within the last
(nx15) minutes, in which case the value will be the
number of complete 15 minute intervals the device has
been online."
::= { sonetMediumEntry 3 }
sonetMediumLineCoding OBJECT-TYPE
SYNTAX INTEGER {
sonetMediumOther(1),
sonetMediumB3ZS(2),
sonetMediumCMI(3),
sonetMediumNRZ(4),
sonetMediumRZ(5)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable describes the line coding for
this interface. The B3ZS and CMI are used for
electrical SONET/SDH signals (STS-1 and STS-3).
The Non-Return to Zero (NRZ) and the Return
to Zero are used for optical SONET/SDH signals."
::= { sonetMediumEntry 4 }
sonetMediumLineType OBJECT-TYPE
SYNTAX INTEGER {
sonetOther(1),
sonetShortSingleMode(2),
sonetLongSingleMode(3),
sonetMultiMode(4),
sonetCoax(5),
sonetUTP(6)
}
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable describes the line type for
this interface. The line types are
Short and Long Range
AToM MIB Working Group [Page 20]
RFC 1595 SONET/SDH Objects March 1994
Single Mode fiber or Multi-Mode fiber interfaces,
and coax and UTP for electrical interfaces. The
value sonetOther should be used when the Line Type is
not one of the listed values."
::= { sonetMediumEntry 5 }
sonetMediumCircuitIdentifier OBJECT-TYPE
SYNTAX DisplayString (SIZE (0..255))
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable contains the transmission
vendor's circuit identifier, for the
purpose of facilitating troubleshooting."
::= { sonetMediumEntry 6 }
-- the SONET/SDH Section group
-- this group consists of 2 tables:
-- - the SONET/SDH Section Current Table
-- - the SONET/SDH Section Interval Table
-- the SONET/SDH Section Current Table
-- The SONET/SDH Section
-- current table contains various statistics
-- being collected for the current 15 minute interval.
sonetSectionCurrentTable OBJECT-TYPE
SYNTAX SEQUENCE OF SonetSectionCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The SONET/SDH Section Current table."
::= { sonetSection 1 }
sonetSectionCurrentEntry OBJECT-TYPE
SYNTAX SonetSectionCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the SONET/SDH Section Current table."
INDEX { ifIndex }
::= { sonetSectionCurrentTable 1 }
AToM MIB Working Group [Page 21]
RFC 1595 SONET/SDH Objects March 1994
SonetSectionCurrentEntry ::=
SEQUENCE {
sonetSectionCurrentStatus Integer32,
sonetSectionCurrentESs Gauge32,
sonetSectionCurrentSESs Gauge32,
sonetSectionCurrentSEFSs Gauge32,
sonetSectionCurrentCVs Gauge32
}
sonetSectionCurrentStatus OBJECT-TYPE
SYNTAX Integer32 (1..6)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable indicates the
status of the interface.
The sonetSectionCurrentStatus
is a bit map represented
as a sum, therefore,
it can represent multiple defects
simultaneously.
The sonetSectionNoDefect should be
set if and only if
no other flag is set.
The various bit positions are:
1 sonetSectionNoDefect
2 sonetSectionLOS
4 sonetSectionLOF"
::= { sonetSectionCurrentEntry 1 }
sonetSectionCurrentESs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of Errored
Seconds encountered by a SONET/SDH
Section in the current 15 minute interval."
::= { sonetSectionCurrentEntry 2 }
sonetSectionCurrentSESs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of
AToM MIB Working Group [Page 22]
RFC 1595 SONET/SDH Objects March 1994
Severely Errored Seconds
encountered by a SONET/SDH Section in the current 15
minute interval."
::= { sonetSectionCurrentEntry 3 }
sonetSectionCurrentSEFSs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of
Severely Errored Framing Seconds
encountered by a SONET/SDH Section in the current
15 minute interval."
::= { sonetSectionCurrentEntry 4 }
sonetSectionCurrentCVs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of Coding
Violations encountered by a
SONET/SDH Section in the current 15 minute interval."
::= { sonetSectionCurrentEntry 5 }
-- the SONET/SDH Section Interval Table
-- The SONET/SDH Section Interval Table
-- contains various statistics
-- collected by each system over a maximum
-- of the previous 24 hours of
-- operation. The past 24 hours may be broken into 96
-- completed 15 minute intervals.
-- A system is required to store at
-- least 4 completed 15 minute interval.
-- The default value is 32 intervals.
sonetSectionIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF SonetSectionIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The SONET/SDH Section Interval table."
::= { sonetSection 2 }
sonetSectionIntervalEntry OBJECT-TYPE
AToM MIB Working Group [Page 23]
RFC 1595 SONET/SDH Objects March 1994
SYNTAX SonetSectionIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the SONET/SDH Section Interval table."
INDEX { ifIndex,
sonetSectionIntervalNumber }
::= { sonetSectionIntervalTable 1 }
SonetSectionIntervalEntry ::=
SEQUENCE {
sonetSectionIntervalNumber Integer32,
sonetSectionIntervalESs Gauge32,
sonetSectionIntervalSESs Gauge32,
sonetSectionIntervalSEFSs Gauge32,
sonetSectionIntervalCVs Gauge32
}
sonetSectionIntervalNumber OBJECT-TYPE
SYNTAX Integer32 (1..96)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A number between 1 and 96, which identifies the
interval for which the set of statistics is available.
The interval identified by 1 is the most recently
completed 15 minute interval,
and the interval identified
by N is the interval immediately preceding the
one identified
by N-1."
::= { sonetSectionIntervalEntry 1 }
sonetSectionIntervalESs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of
Errored Seconds encountered
by a SONET/SDH Section in a
particular 15-minute interval
in the past 24 hours."
::= { sonetSectionIntervalEntry 2 }
sonetSectionIntervalSESs OBJECT-TYPE
SYNTAX Gauge32
AToM MIB Working Group [Page 24]
RFC 1595 SONET/SDH Objects March 1994
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of
Severely Errored Seconds
encountered by a SONET/SDH Section in a
particular 15-minute interval
in the past 24 hours."
::= { sonetSectionIntervalEntry 3 }
sonetSectionIntervalSEFSs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of
Severely Errored Framing Seconds
encountered by a SONET/SDH Section in a
particular 15-minute interval
in the past 24 hours."
::= { sonetSectionIntervalEntry 4 }
sonetSectionIntervalCVs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of Coding
Violations encountered by a
SONET/SDH Section in a particular 15-minute interval
in the past 24 hours."
::= { sonetSectionIntervalEntry 5 }
-- the SONET/SDH Line group
-- this group consists of 2 tables:
-- - the SONET/SDH Line Current Table
-- - the SONET/SDH Line Interval Table
-- the SONET/SDH Line Current Table
-- The SONET/SDH Line
-- current table contains various statistics
-- being collected for the current 15 minute interval.
sonetLineCurrentTable OBJECT-TYPE
AToM MIB Working Group [Page 25]
RFC 1595 SONET/SDH Objects March 1994
SYNTAX SEQUENCE OF SonetLineCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The SONET/SDH Line Current table."
::= { sonetLine 1 }
sonetLineCurrentEntry OBJECT-TYPE
SYNTAX SonetLineCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the SONET/SDH Line Current table."
INDEX { ifIndex }
::= { sonetLineCurrentTable 1 }
SonetLineCurrentEntry ::=
SEQUENCE {
sonetLineCurrentStatus Integer32,
sonetLineCurrentESs Gauge32,
sonetLineCurrentSESs Gauge32,
sonetLineCurrentCVs Gauge32,
sonetLineCurrentUASs Gauge32
}
sonetLineCurrentStatus OBJECT-TYPE
SYNTAX Integer32 (1..6)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable indicates the
status of the interface.
The sonetLineCurrentStatus
is a bit map represented
as a sum, therefore,
it can represent multiple defects
simultaneously.
The sonetLineNoDefect should be
set if and only if
no other flag is set.
The various bit positions are:
1 sonetLineNoDefect
2 sonetLineAIS
4 sonetLineRDI"
::= { sonetLineCurrentEntry 1 }
AToM MIB Working Group [Page 26]
RFC 1595 SONET/SDH Objects March 1994
sonetLineCurrentESs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of Errored
Seconds encountered by a SONET/SDH
Line in the current 15 minute interval."
::= { sonetLineCurrentEntry 2 }
sonetLineCurrentSESs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of
Severely Errored Seconds
encountered by a SONET/SDH Line in the current 15
minute
interval."
::= { sonetLineCurrentEntry 3 }
sonetLineCurrentCVs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of Coding
Violations encountered by a
SONET/SDH Line in the current 15 minute interval."
::= { sonetLineCurrentEntry 4 }
sonetLineCurrentUASs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of
Unavailable Seconds
encountered by a SONET/SDH Line in the current 15
minute
interval."
::= { sonetLineCurrentEntry 5 }
-- the SONET/SDH Line Interval Table
-- The SONET/SDH Line Interval Table
AToM MIB Working Group [Page 27]
RFC 1595 SONET/SDH Objects March 1994
-- contains various statistics
-- collected by each system over a maximum
-- of the previous 24 hours of
-- operation. The past 24 hours may be broken into 96
-- completed 15 minute intervals.
-- A system is required to store at
-- least 4 completed 15 minute interval.
-- The default value is 32 intervals.
sonetLineIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF SonetLineIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The SONET/SDH Line Interval table."
::= { sonetLine 2 }
sonetLineIntervalEntry OBJECT-TYPE
SYNTAX SonetLineIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the SONET/SDH Line Interval table."
INDEX { ifIndex,
sonetLineIntervalNumber }
::= { sonetLineIntervalTable 1 }
SonetLineIntervalEntry ::=
SEQUENCE {
sonetLineIntervalNumber Integer32,
sonetLineIntervalESs Gauge32,
sonetLineIntervalSESs Gauge32,
sonetLineIntervalCVs Gauge32,
sonetLineIntervalUASs Gauge32
}
sonetLineIntervalNumber OBJECT-TYPE
SYNTAX Integer32 (1..96)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A number between 1 and 96, which identifies the
interval for which the set of statistics is available.
The interval identified by 1 is the most recently
completed 15 minute interval,
and the interval identified
by N is the interval immediately preceding the
AToM MIB Working Group [Page 28]
RFC 1595 SONET/SDH Objects March 1994
one identified
by N-1."
::= { sonetLineIntervalEntry 1 }
sonetLineIntervalESs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of
Errored Seconds encountered
by a SONET/SDH Line in a
particular 15-minute interval
in the past 24 hours."
::= { sonetLineIntervalEntry 2 }
sonetLineIntervalSESs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of
Severely Errored Seconds
encountered by a SONET/SDH Line in a
particular 15-minute interval
in the past 24 hours."
::= { sonetLineIntervalEntry 3 }
sonetLineIntervalCVs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of Coding
Violations encountered by a
SONET/SDH Line in a
particular 15-minute interval
in the past 24 hours."
::= { sonetLineIntervalEntry 4 }
sonetLineIntervalUASs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the
number of Unavailable Seconds
encountered by a SONET/SDH Line in
AToM MIB Working Group [Page 29]
RFC 1595 SONET/SDH Objects March 1994
a particular 15-minute interval
in the past 24 hours."
::= { sonetLineIntervalEntry 5 }
-- The SONET/SDH Far End Line group.
-- This group may only be implemented by SONET/SDH (LTEs)
-- systems that provide for a far end block error (FEBE)
-- information at the SONET/SDH Line Layer.
-- This group consists of two tables:
-- SONET/SDH Far End Line Current Table
-- SONET/SDH Far End Line Interval Table
-- The SONET/SDH Far End Line Current Table
-- The SONET/SDH Far End Line Current table contains
-- various statistics being
-- collected for the current 15 minute interval.
-- The statistics are collected from the far end
-- block error code (FEBE)
-- within the third Z2 byte of the Line Overhead
-- in Broadband ISDN applications.
-- The definitions are the same as described for
-- the near-end information.
sonetFarEndLineCurrentTable OBJECT-TYPE
SYNTAX SEQUENCE OF SonetFarEndLineCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The SONET/SDH Far End Line Current table."
::= { sonetFarEndLine 1 }
sonetFarEndLineCurrentEntry OBJECT-TYPE
SYNTAX SonetFarEndLineCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the SONET/SDH Far End Line Current table."
INDEX { ifIndex }
::= { sonetFarEndLineCurrentTable 1 }
SonetFarEndLineCurrentEntry ::=
SEQUENCE {
sonetFarEndLineCurrentESs Gauge32,
AToM MIB Working Group [Page 30]
RFC 1595 SONET/SDH Objects March 1994
sonetFarEndLineCurrentSESs Gauge32,
sonetFarEndLineCurrentCVs Gauge32,
sonetFarEndLineCurrentUASs Gauge32
}
sonetFarEndLineCurrentESs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of Far
Far End Errored Seconds encountered by a SONET/SDH
interface in the current 15 minute interval."
::= { sonetFarEndLineCurrentEntry 1 }
sonetFarEndLineCurrentSESs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of
Far End Severely Errored Seconds
encountered by a SONET/SDH Medium/Section/Line
interface in the current 15 minute
interval."
::= { sonetFarEndLineCurrentEntry 2 }
sonetFarEndLineCurrentCVs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of
Far End Coding Violations reported via
the far end block error count
encountered by a
SONET/SDH Medium/Section/Line
interface in the current 15 minute interval."
::= { sonetFarEndLineCurrentEntry 3 }
sonetFarEndLineCurrentUASs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of
Far End Unavailable Seconds
AToM MIB Working Group [Page 31]
RFC 1595 SONET/SDH Objects March 1994
encountered by a
SONET/SDH Medium/Section/Line
interface in the current 15 minute interval."
::= { sonetFarEndLineCurrentEntry 4 }
-- The SONET/SDH Far End Line Interval Table
-- The SONET/SDH Far End Line Interval Table
-- contains various statistics
-- collected by each system over a maximum
-- of the previous 24 hours of
-- operation. The past 24 hours may be broken into 96
-- completed 15 minute intervals.
-- A system is required to store at
-- least 4 completed 15 minute interval.
-- The default value is 32 intervals.
sonetFarEndLineIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF SonetFarEndLineIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The SONET/SDH Far End Line Interval table."
::= { sonetFarEndLine 2 }
sonetFarEndLineIntervalEntry OBJECT-TYPE
SYNTAX SonetFarEndLineIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the SONET/SDH Far
End Line Interval table."
INDEX { ifIndex,
sonetFarEndLineIntervalNumber }
::= { sonetFarEndLineIntervalTable 1 }
SonetFarEndLineIntervalEntry ::=
SEQUENCE {
sonetFarEndLineIntervalNumber Integer32,
sonetFarEndLineIntervalESs Gauge32,
sonetFarEndLineIntervalSESs Gauge32,
sonetFarEndLineIntervalCVs Gauge32,
sonetFarEndLineIntervalUASs Gauge32
}
sonetFarEndLineIntervalNumber OBJECT-TYPE
AToM MIB Working Group [Page 32]
RFC 1595 SONET/SDH Objects March 1994
SYNTAX Integer32 (1..96)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A number between 1 and 96, which identifies the
interval for which the set of statistics is available.
The interval identified by 1 is the most recently
completed 15 minute interval,
and the interval identified
by N is the interval immediately preceding the
one identified
by N-1."
::= { sonetFarEndLineIntervalEntry 1 }
sonetFarEndLineIntervalESs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of
Far End Errored Seconds encountered
by a SONET/SDH Line
interface in a particular 15-minute interval
in the past 24 hours."
::= { sonetFarEndLineIntervalEntry 2 }
sonetFarEndLineIntervalSESs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of
Far End Severely Errored Seconds
encountered by a SONET/SDH Line
interface in a particular 15-minute interval
in the past 24 hours."
::= { sonetFarEndLineIntervalEntry 3 }
sonetFarEndLineIntervalCVs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of
Far End Coding Violations reported via
the far end block error count
encountered by a
SONET/SDH Line
AToM MIB Working Group [Page 33]
RFC 1595 SONET/SDH Objects March 1994
interface in a particular 15-minute interval
in the past 24 hours."
::= { sonetFarEndLineIntervalEntry 4 }
sonetFarEndLineIntervalUASs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of
Far End Unavailable Seconds
encountered by a
SONET/SDH Line
interface in a particular 15-minute interval
in the past 24 hours."
::= { sonetFarEndLineIntervalEntry 5 }
-- the SONET/SDH Path group
-- this group consists of 2 tables:
-- - the SONET/SDH Path Current Table
-- - the SONET/SDH Path Interval Table
-- the SONET/SDH Path Current Table
-- The SONET/SDH Path
-- current table contains various statistics
-- being collected for the current 15 minute interval.
sonetPathCurrentTable OBJECT-TYPE
SYNTAX SEQUENCE OF SonetPathCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The SONET/SDH Path Current table."
::= { sonetPath 1 }
sonetPathCurrentEntry OBJECT-TYPE
SYNTAX SonetPathCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the SONET/SDH Path Current table."
INDEX { ifIndex }
::= { sonetPathCurrentTable 1 }
AToM MIB Working Group [Page 34]
RFC 1595 SONET/SDH Objects March 1994
SonetPathCurrentEntry ::=
SEQUENCE {
sonetPathCurrentWidth INTEGER,
sonetPathCurrentStatus Integer32,
sonetPathCurrentESs Gauge32,
sonetPathCurrentSESs Gauge32,
sonetPathCurrentCVs Gauge32,
sonetPathCurrentUASs Gauge32
}
sonetPathCurrentWidth OBJECT-TYPE
SYNTAX INTEGER {
sts1(1),
sts3cSTM1(2),
sts12cSTM4(3),
sts24c(4),
sts48cSTM16(5)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"A value that indicates the type of the SONET/SDH
Path. For SONET, the assigned types are
the STS-Nc SPEs, where N = 1, 3, 12, 24, and 48.
STS-1 is equal to 51.84 Mbps. For SDH, the assigned
types are the STM-Nc VCs, where N = 1, 4, and 16."
::= { sonetPathCurrentEntry 1 }
sonetPathCurrentStatus OBJECT-TYPE
SYNTAX Integer32 (1..14)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable indicates the
status of the interface.
The sonetPathCurrentStatus
is a bit map represented
as a sum, therefore,
it can represent multiple defects
simultaneously.
The sonetPathNoDefect should be
set if and only if
no other flag is set.
The various bit positions are:
1 sonetPathNoDefect
2 sonetPathSTSLOP
AToM MIB Working Group [Page 35]
RFC 1595 SONET/SDH Objects March 1994
4 sonetPathSTSAIS
8 sonetPathSTSRDI
16 sonetPathUnequipped
32 sonetPathSignalLabelMismatch"
::= { sonetPathCurrentEntry 2 }
sonetPathCurrentESs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of Errored
Seconds encountered by a SONET/SDH
Path in the current 15 minute interval."
::= { sonetPathCurrentEntry 3 }
sonetPathCurrentSESs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of
Severely Errored Seconds
encountered by a SONET/SDH Path in the current 15
minute
interval."
::= { sonetPathCurrentEntry 4 }
sonetPathCurrentCVs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of Coding
Violations encountered by a
SONET/SDH Path in the current 15 minute interval."
::= { sonetPathCurrentEntry 5 }
sonetPathCurrentUASs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of
Unavailable Seconds
encountered by a Path in the current
15 minute, interval."
::= { sonetPathCurrentEntry 6 }
AToM MIB Working Group [Page 36]
RFC 1595 SONET/SDH Objects March 1994
-- the SONET/SDH Path Interval Table
-- The SONET/SDH Path Interval Table
-- contains various statistics
-- collected by each system over a maximum
-- of the previous 24 hours of
-- operation. The past 24 hours may be broken into 96
-- completed 15 minute intervals.
-- A system is required to store at
-- least 4 completed 15 minute interval.
-- The default value is 32 intervals.
sonetPathIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF SonetPathIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The SONET/SDH Path Interval table."
::= { sonetPath 2 }
sonetPathIntervalEntry OBJECT-TYPE
SYNTAX SonetPathIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the SONET/SDH Path Interval table."
INDEX { ifIndex,
sonetPathIntervalNumber }
::= { sonetPathIntervalTable 1 }
SonetPathIntervalEntry ::=
SEQUENCE {
sonetPathIntervalNumber Integer32,
sonetPathIntervalESs Gauge32,
sonetPathIntervalSESs Gauge32,
sonetPathIntervalCVs Gauge32,
sonetPathIntervalUASs Gauge32
}
sonetPathIntervalNumber OBJECT-TYPE
SYNTAX Integer32 (1..96)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A number between 1 and 96, which identifies the
interval for which the set of statistics is available.
AToM MIB Working Group [Page 37]
RFC 1595 SONET/SDH Objects March 1994
The interval identified by 1 is the most recently
completed 15 minute interval,
and the interval identified
by N is the interval immediately preceding the
one identified
by N-1."
::= { sonetPathIntervalEntry 1 }
sonetPathIntervalESs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of
Errored Seconds encountered
by a SONET/SDH Path in a
particular 15-minute interval
in the past 24 hours."
::= { sonetPathIntervalEntry 2 }
sonetPathIntervalSESs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of
Severely Errored Seconds
encountered by a SONET/SDH Path in
a particular 15-minute interval
in the past 24 hours."
::= { sonetPathIntervalEntry 3 }
sonetPathIntervalCVs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of Coding
Violations encountered by a
SONET/SDH Path in a particular 15-minute interval
in the past 24 hours."
::= { sonetPathIntervalEntry 4 }
sonetPathIntervalUASs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
AToM MIB Working Group [Page 38]
RFC 1595 SONET/SDH Objects March 1994
"The counter associated with the number of
Unavailable Seconds
encountered by a Path in a
particular 15-minute interval
in the past 24 hours."
::= { sonetPathIntervalEntry 5 }
-- The SONET/SDH Far End Path group
-- This group consists of two tables:
-- - SONET/SDH Far End Path Current Table
-- - SONET/SDH Far End Path Interval Table
-- The SONET/SDH Far End Path Current Table
-- The SONET/SDH Far End Path Current table
-- contains various statistics
-- being collected for the current 15 minute interval.
-- The statistics are collected from
-- the far end block error code
-- (FEBE) within the G1 byte of the Path Overhead.
-- The definitions are the same as described for
-- the near-end information.
sonetFarEndPathCurrentTable OBJECT-TYPE
SYNTAX SEQUENCE OF SonetFarEndPathCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The SONET/SDH Far End Path Current table."
::= { sonetFarEndPath 1 }
sonetFarEndPathCurrentEntry OBJECT-TYPE
SYNTAX SonetFarEndPathCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the SONET/SDH Far End Path Current table."
INDEX { ifIndex }
::= { sonetFarEndPathCurrentTable 1 }
SonetFarEndPathCurrentEntry ::=
SEQUENCE {
sonetFarEndPathCurrentESs Gauge32,
sonetFarEndPathCurrentSESs Gauge32,
sonetFarEndPathCurrentCVs Gauge32,
sonetFarEndPathCurrentUASs Gauge32
AToM MIB Working Group [Page 39]
RFC 1595 SONET/SDH Objects March 1994
}
sonetFarEndPathCurrentESs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of Far
Far End Errored Seconds encountered by a SONET/SDH
interface in the current 15 minute interval."
::= { sonetFarEndPathCurrentEntry 1 }
sonetFarEndPathCurrentSESs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of
Far End Severely Errored Seconds
encountered by a SONET/SDH Path
interface in the current 15 minute
interval."
::= { sonetFarEndPathCurrentEntry 2 }
sonetFarEndPathCurrentCVs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of
Far End Coding Violations reported via
the far end block error count
encountered by a
SONET/SDH Path interface in
the current 15 minute interval."
::= { sonetFarEndPathCurrentEntry 3 }
sonetFarEndPathCurrentUASs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of
Far End Unavailable Seconds
encountered by a
SONET/SDH Path interface in
the current 15 minute interval."
AToM MIB Working Group [Page 40]
RFC 1595 SONET/SDH Objects March 1994
::= { sonetFarEndPathCurrentEntry 4 }
-- The SONET/SDH Far End Path Interval Table
-- The SONET/SDH Far End Path Interval Table
-- contains various statistics
-- collected by each system over a maximum
-- of the previous 24 hours of
-- operation. The past 24 hours may be broken into 96
-- completed 15 minute intervals.
-- A system is required to store at
-- least 4 completed 15 minute interval.
-- The default value is 32 intervals.
sonetFarEndPathIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF SonetFarEndPathIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The SONET/SDH Far End Path Interval table."
::= { sonetFarEndPath 2 }
sonetFarEndPathIntervalEntry OBJECT-TYPE
SYNTAX SonetFarEndPathIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the SONET/SDH Far
End Path Interval table."
INDEX { ifIndex,
sonetFarEndPathIntervalNumber }
::= { sonetFarEndPathIntervalTable 1 }
SonetFarEndPathIntervalEntry ::=
SEQUENCE {
sonetFarEndPathIntervalNumber Integer32,
sonetFarEndPathIntervalESs Gauge32,
sonetFarEndPathIntervalSESs Gauge32,
sonetFarEndPathIntervalCVs Gauge32,
sonetFarEndPathIntervalUASs Gauge32
}
sonetFarEndPathIntervalNumber OBJECT-TYPE
SYNTAX Integer32 (1..96)
MAX-ACCESS not-accessible
STATUS current
AToM MIB Working Group [Page 41]
RFC 1595 SONET/SDH Objects March 1994
DESCRIPTION
"A number between 1 and 96, which identifies the
interval for which the set of statistics is available.
The interval identified by 1 is the most recently
completed 15 minute interval,
and the interval identified
by N is the interval immediately preceding the
one identified
by N-1."
::= { sonetFarEndPathIntervalEntry 1 }
sonetFarEndPathIntervalESs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of
Far End Errored Seconds encountered
by a SONET/SDH Path interface in a
particular 15-minute interval
in the past 24 hours."
::= { sonetFarEndPathIntervalEntry 2 }
sonetFarEndPathIntervalSESs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of
Far End Severely Errored Seconds
encountered by a SONET/SDH Path interface
in a particular 15-minute interval
in the past 24 hours."
::= { sonetFarEndPathIntervalEntry 3 }
sonetFarEndPathIntervalCVs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of
Far End Coding Violations reported via
the far end block error count
encountered by a
SONET/SDH Path interface
in a particular 15-minute interval
in the past 24 hours."
::= { sonetFarEndPathIntervalEntry 4 }
AToM MIB Working Group [Page 42]
RFC 1595 SONET/SDH Objects March 1994
sonetFarEndPathIntervalUASs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of
Far End Unavailable Seconds
encountered by a
SONET/SDH Path interface in
a particular 15-minute interval
in the past 24 hours."
::= { sonetFarEndPathIntervalEntry 5 }
-- the SONET/SDH Virtual Tributary group
-- this group consists of 2 tables:
-- - the SONET/SDH VT Current Table
-- - the SONET/SDH VT Interval Table
-- For SDH signals, virtual tributaries are
-- called VCs instead of VTs
-- A VT1.5 = VC11
-- A VT2 = VC12
-- A VT3 = none
-- A VT6 = VC3
-- the SONET/SDH VT Current Table
-- The SONET/SDH VT current table
-- contains various statistics
-- being collected for the
-- current 15 minute interval.
sonetVTCurrentTable OBJECT-TYPE
SYNTAX SEQUENCE OF SonetVTCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The SONET/SDH VT Current table."
::= { sonetVT 1 }
sonetVTCurrentEntry OBJECT-TYPE
SYNTAX SonetVTCurrentEntry
MAX-ACCESS not-accessible
STATUS current
AToM MIB Working Group [Page 43]
RFC 1595 SONET/SDH Objects March 1994
DESCRIPTION
"An entry in the SONET/SDH VT Current table."
INDEX { ifIndex }
::= { sonetVTCurrentTable 1 }
SonetVTCurrentEntry ::=
SEQUENCE {
sonetVTCurrentWidth INTEGER,
sonetVTCurrentStatus Integer32,
sonetVTCurrentESs Gauge32,
sonetVTCurrentSESs Gauge32,
sonetVTCurrentCVs Gauge32,
sonetVTCurrentUASs Gauge32
}
sonetVTCurrentWidth OBJECT-TYPE
SYNTAX INTEGER {
vtWidth15VC11(1),
vtWidth2VC12(2),
vtWidth3(3),
vtWidth6VC2(4),
vtWidth6c(5)
}
MAX-ACCESS read-write
STATUS current
DESCRIPTION
"A value that indicates the type of the SONET
VT and SDH VC. Assigned widths are
VT1.5/VC11, VT2/VC12, VT3, VT6/VC2, and VT6c."
::= { sonetVTCurrentEntry 1 }
sonetVTCurrentStatus OBJECT-TYPE
SYNTAX Integer32 (1..30)
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"This variable indicates the
status of the interface.
The sonetVTCurrentStatus
is a bit map represented
as a sum, therefore,
it can represent multiple defects
and failures
simultaneously.
The sonetVTNoDefect should be
set if and only if
no other flag is set.
AToM MIB Working Group [Page 44]
RFC 1595 SONET/SDH Objects March 1994
The various bit positions are:
1 sonetVTNoDefect
2 sonetVTLOP
4 sonetVTPathAIS
8 sonetVTPathRDI
16 sonetVTPathRFI
32 sonetVTUnequipped
64 sonetVTSignalLabelMismatch"
::= { sonetVTCurrentEntry 2 }
sonetVTCurrentESs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of Errored
Seconds encountered by a SONET/SDH
VT in the current 15 minute interval."
::= { sonetVTCurrentEntry 3 }
sonetVTCurrentSESs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of
Severely Errored Seconds
encountered by a SONET/SDH VT in the current 15 minute
interval."
::= { sonetVTCurrentEntry 4 }
sonetVTCurrentCVs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of Coding
Violations encountered by a
SONET/SDH VT in the current 15 minute interval."
::= { sonetVTCurrentEntry 5 }
sonetVTCurrentUASs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of
Unavailable Seconds
AToM MIB Working Group [Page 45]
RFC 1595 SONET/SDH Objects March 1994
encountered by a VT in the current
15 minute, interval."
::= { sonetVTCurrentEntry 6 }
-- the SONET/SDH VT Interval Table
-- The SONET/SDH VT Interval Table
-- contains various statistics
-- collected by each system over a maximum
-- of the previous 24 hours of
-- operation. The past 24 hours may be broken into 96
-- completed 15 minute intervals.
-- A system is required to store at
-- least 4 completed 15 minute interval.
-- The default value is 32 intervals.
sonetVTIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF SonetVTIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The SONET/SDH VT Interval table."
::= { sonetVT 2 }
sonetVTIntervalEntry OBJECT-TYPE
SYNTAX SonetVTIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the SONET/SDH VT Interval table."
INDEX { ifIndex,
sonetVTIntervalNumber }
::= { sonetVTIntervalTable 1 }
SonetVTIntervalEntry ::=
SEQUENCE {
sonetVTIntervalNumber Integer32,
sonetVTIntervalESs Gauge32,
sonetVTIntervalSESs Gauge32,
sonetVTIntervalCVs Gauge32,
sonetVTIntervalUASs Gauge32
}
sonetVTIntervalNumber OBJECT-TYPE
SYNTAX Integer32 (1..96)
MAX-ACCESS not-accessible
AToM MIB Working Group [Page 46]
RFC 1595 SONET/SDH Objects March 1994
STATUS current
DESCRIPTION
"A number between 1 and 96, which identifies the
interval for which the set of statistics is available.
The interval identified by 1 is the most recently
completed 15 minute interval,
and the interval identified
by N is the interval immediately preceding the
one identified
by N-1."
::= { sonetVTIntervalEntry 1 }
sonetVTIntervalESs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of
Errored Seconds encountered
by a SONET/SDH VT in a particular 15-minute interval
in the past 24 hours."
::= { sonetVTIntervalEntry 2 }
sonetVTIntervalSESs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of
Severely Errored Seconds
encountered by a SONET/SDH VT
in a particular 15-minute interval
in the past 24 hours."
::= { sonetVTIntervalEntry 3 }
sonetVTIntervalCVs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of Coding
Violations encountered by a
SONET/SDH VT in a particular 15-minute interval
in the past 24 hours."
::= { sonetVTIntervalEntry 4 }
sonetVTIntervalUASs OBJECT-TYPE
SYNTAX Gauge32
AToM MIB Working Group [Page 47]
RFC 1595 SONET/SDH Objects March 1994
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of
Unavailable Seconds
encountered by a VT in a particular 15-minute interval
in the past 24 hours."
::= { sonetVTIntervalEntry 5 }
-- The SONET/SDH Far End VT group
-- This group consists of two tables:
-- SONET/SDH Far End VT Current Table
-- SONET/SDH Far End VT Interval Table
-- The SONET/SDH Far End VT Current
-- The SONET/SDH Far End VT Current table
-- contains various statistics
-- being collected for the current 15 minute interval.
-- The statistics are collected from
-- the far end block error code
-- (FEBE) within the G1 byte of the VT Overhead.
-- The definitions are the same as described for
-- the near-end information.
sonetFarEndVTCurrentTable OBJECT-TYPE
SYNTAX SEQUENCE OF SonetFarEndVTCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The SONET/SDH Far End VT Current table."
::= { sonetFarEndVT 1 }
sonetFarEndVTCurrentEntry OBJECT-TYPE
SYNTAX SonetFarEndVTCurrentEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the SONET/SDH Far End VT Current table."
INDEX { ifIndex }
::= { sonetFarEndVTCurrentTable 1 }
SonetFarEndVTCurrentEntry ::=
SEQUENCE {
sonetFarEndVTCurrentESs Gauge32,
AToM MIB Working Group [Page 48]
RFC 1595 SONET/SDH Objects March 1994
sonetFarEndVTCurrentSESs Gauge32,
sonetFarEndVTCurrentCVs Gauge32,
sonetFarEndVTCurrentUASs Gauge32
}
sonetFarEndVTCurrentESs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of Far
Far End Errored Seconds encountered by a SONET/SDH
interface in the current 15 minute interval."
::= { sonetFarEndVTCurrentEntry 1 }
sonetFarEndVTCurrentSESs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of
Far End Severely Errored Seconds
encountered by a SONET/SDH VT interface
in the current 15 minute
interval."
::= { sonetFarEndVTCurrentEntry 2 }
sonetFarEndVTCurrentCVs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of
Far End Coding Violations reported via
the far end block error count
encountered by a
SONET/SDH VT interface
in the current 15 minute interval."
::= { sonetFarEndVTCurrentEntry 3 }
sonetFarEndVTCurrentUASs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of
Far End Unavailable Seconds
AToM MIB Working Group [Page 49]
RFC 1595 SONET/SDH Objects March 1994
encountered by a
SONET/SDH VT interface
in the current 15 minute interval."
::= { sonetFarEndVTCurrentEntry 4 }
-- The SONET/SDH Far End VT Interval Table
-- The SONET/SDH Far End VT Interval Table
-- contains various statistics
-- collected by each system over a maximum
-- of the previous 24 hours of
-- operation. The past 24 hours may be broken into 96
-- completed 15 minute intervals.
-- A system is required to store at
-- least 4 completed 15 minute interval.
-- The default value is 32 intervals.
sonetFarEndVTIntervalTable OBJECT-TYPE
SYNTAX SEQUENCE OF SonetFarEndVTIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"The SONET/SDH Far End VT Interval table."
::= { sonetFarEndVT 2 }
sonetFarEndVTIntervalEntry OBJECT-TYPE
SYNTAX SonetFarEndVTIntervalEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"An entry in the SONET/SDH Far
End VT Interval table."
INDEX { ifIndex,
sonetFarEndVTIntervalNumber }
::= { sonetFarEndVTIntervalTable 1 }
SonetFarEndVTIntervalEntry ::=
SEQUENCE {
sonetFarEndVTIntervalNumber Integer32,
sonetFarEndVTIntervalESs Gauge32,
sonetFarEndVTIntervalSESs Gauge32,
sonetFarEndVTIntervalCVs Gauge32,
sonetFarEndVTIntervalUASs Gauge32
}
sonetFarEndVTIntervalNumber OBJECT-TYPE
AToM MIB Working Group [Page 50]
RFC 1595 SONET/SDH Objects March 1994
SYNTAX Integer32 (1..96)
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"A number between 1 and 96, which identifies the
interval for which the set of statistics is available.
The interval identified by 1 is the most recently
completed 15 minute interval,
and the interval identified
by N is the interval immediately preceding the
one identified
by N-1."
::= { sonetFarEndVTIntervalEntry 1 }
sonetFarEndVTIntervalESs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of
Far End Errored Seconds encountered
by a SONET/SDH VT interface
in a particular 15-minute interval
in the past 24 hours."
::= { sonetFarEndVTIntervalEntry 2 }
sonetFarEndVTIntervalSESs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of
Far End Severely Errored Seconds
encountered by a SONET/SDH VT interface
in a particular 15-minute interval
in the past 24 hours."
::= { sonetFarEndVTIntervalEntry 3 }
sonetFarEndVTIntervalCVs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of
Far End Coding Violations reported via
the far end block error count
encountered by a
SONET/SDH VT interface in a
AToM MIB Working Group [Page 51]
RFC 1595 SONET/SDH Objects March 1994
particular 15-minute interval
in the past 24 hours."
::= { sonetFarEndVTIntervalEntry 4 }
sonetFarEndVTIntervalUASs OBJECT-TYPE
SYNTAX Gauge32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"The counter associated with the number of
Far End Unavailable Seconds
encountered by a
SONET/SDH VT interface in a
particular 15-minute interval
in the past 24 hours."
::= { sonetFarEndVTIntervalEntry 5 }
-- conformance information
sonetConformance OBJECT IDENTIFIER ::= { sonetMIB 4 }
sonetGroups OBJECT IDENTIFIER ::= { sonetConformance 1 }
sonetCompliances OBJECT IDENTIFIER ::= { sonetConformance 2 }
-- compliance statements
sonetCompliance MODULE-COMPLIANCE
STATUS current
DESCRIPTION
"The compliance statement for SONET/SDH
interfaces."
MODULE -- this module
MANDATORY-GROUPS { sonetMediumStuff, sonetSectionStuff }
GROUP sonetLineStuff
DESCRIPTION
"Implementation of this group is mandatory for all
SONET/SDH systems that terminate SONET/SDH Lines,
Paths or Virtual Tributaries."
GROUP sonetFarEndLineStuff
DESCRIPTION
"Implementation of this group is optional for all
SONET/SDH systems that terminate SONET/SDH Lines,
Paths or Virtual Tributaries, and that
AToM MIB Working Group [Page 52]
RFC 1595 SONET/SDH Objects March 1994
provide for a far end block error (FEBE)
information at the SONET/SDH Line Layer."
GROUP sonetPathStuff
DESCRIPTION
"Implementation of this group is mandatory for all
SONET/SDH systems that terminate SONET/SDH
Paths or Virtual
Tributaries."
OBJECT sonetPathWidth
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
GROUP sonetFarEndPathStuff
DESCRIPTION
"Implementation of this group is optional for all
SONET/SDH systems that terminate SONET/SDH
Paths or Virtual
Tributaries, and that process
Far End information."
GROUP sonetVTStuff
DESCRIPTION
"Implementation of this group is mandatory for all
SONET/SDH systems that terminate SONET/SDH
Virtual Tributaries."
OBJECT sonetVTWidth
MIN-ACCESS read-only
DESCRIPTION
"Write access is not required."
GROUP sonetFarEndVTStuff
DESCRIPTION
"Implementation of this group is optional for
all SONET/SDH systems that terminate the
SONET/SDH floating Virtual Tributaries, and
that process Far End information."
::= { sonetCompliances 1 }
-- units of conformance
sonetMediumStuff OBJECT-GROUP
OBJECTS { sonetMediumType,
sonetMediumTimeElapsed,
AToM MIB Working Group [Page 53]
RFC 1595 SONET/SDH Objects March 1994
sonetMediumValidIntervals,
sonetMediumLineCoding,
sonetMediumLineType,
sonetMediumCircuitIdentifier }
STATUS current
DESCRIPTION
"A collection of objects providing configuration
information applicable to all SONET/SDH
interfaces."
::= { sonetGroups 1 }
sonetSectionStuff OBJECT-GROUP
OBJECTS { sonetSectionCurrentStatus,
sonetSectionCurrentESs,
sonetSectionCurrentSESs,
sonetSectionCurrentSEFSs,
sonetSectionCurrentCVs,
sonetSectionIntervalESs,
sonetSectionIntervalSESs,
sonetSectionIntervalSEFSs,
sonetSectionIntervalCVs
}
STATUS current
DESCRIPTION
"A collection of objects providing information
specific to SONET/SDH Section interfaces."
::= { sonetGroups 2 }
sonetLineStuff OBJECT-GROUP
OBJECTS { sonetLineCurrentStatus,
sonetLineCurrentESs,
sonetLineCurrentSESs,
sonetLineCurrentCVs,
sonetLineCurrentUASs,
sonetLineIntervalESs,
sonetLineIntervalSESs,
sonetLineIntervalCVs,
sonetLineIntervalUASs }
STATUS current
DESCRIPTION
"A collection of objects providing information
specific to SONET/SDH Line interfaces."
::= { sonetGroups 3 }
sonetFarEndLineStuff OBJECT-GROUP
OBJECTS { sonetFarEndLineCurrentESs,
sonetFarEndLineCurrentSESs,
sonetFarEndLineCurrentCVs,
AToM MIB Working Group [Page 54]
RFC 1595 SONET/SDH Objects March 1994
sonetFarEndLineCurrentUASs,
sonetFarEndLineIntervalESs,
sonetFarEndLineIntervalSESs,
sonetFarEndLineIntervalCVs,
sonetFarEndLineIntervalUASs }
STATUS current
DESCRIPTION
"A collection of objects providing information
specific to SONET/SDH Line interfaces,
and maintaining Line Far End information."
::= { sonetGroups 4 }
sonetPathStuff OBJECT-GROUP
OBJECTS { sonetPathCurrentWidth,
sonetPathCurrentStatus,
sonetPathCurrentESs,
sonetPathCurrentSESs,
sonetPathCurrentCVs,
sonetPathCurrentUASs,
sonetPathIntervalESs,
sonetPathIntervalSESs,
sonetPathIntervalCVs,
sonetPathIntervalUASs }
STATUS current
DESCRIPTION
"A collection of objects providing information
specific to SONET/SDH Path interfaces."
::= { sonetGroups 5 }
sonetFarEndPathStuff OBJECT-GROUP
OBJECTS { sonetFarEndPathCurrentESs,
sonetFarEndPathCurrentSESs,
sonetFarEndPathCurrentCVs,
sonetFarEndPathCurrentUASs,
sonetFarEndPathIntervalESs,
sonetFarEndPathIntervalSESs,
sonetFarEndPathIntervalCVs,
sonetFarEndPathIntervalUASs }
STATUS current
DESCRIPTION
"A collection of objects providing information
specific to SONET/SDH Path interfaces,
and maintaining Path Far End information."
::= { sonetGroups 6 }
sonetVTStuff OBJECT-GROUP
OBJECTS { sonetVTCurrentWidth,
sonetVTCurrentStatus,
AToM MIB Working Group [Page 55]
RFC 1595 SONET/SDH Objects March 1994
sonetVTCurrentESs,
sonetVTCurrentSESs,
sonetVTCurrentCVs,
sonetVTCurrentUASs,
sonetVTIntervalESs,
sonetVTIntervalSESs,
sonetVTIntervalCVs,
sonetVTIntervalUASs }
STATUS current
DESCRIPTION
"A collection of objects providing information
specific to SONET/SDH VT interfaces."
::= { sonetGroups 7 }
sonetFarEndVTStuff OBJECT-GROUP
OBJECTS { sonetFarEndVTCurrentESs,
sonetFarEndVTCurrentSESs,
sonetFarEndVTCurrentCVs,
sonetFarEndVTCurrentUASs,
sonetFarEndVTIntervalESs,
sonetFarEndVTIntervalSESs,
sonetFarEndVTIntervalCVs,
sonetFarEndVTIntervalUASs }
STATUS current
DESCRIPTION
"A collection of objects providing information
specific to SONET/SDH VT interfaces,
and maintaining VT Far End information."
::= { sonetGroups 8 }
END
[1] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Structure
of Management Information for version 2 of the Simple Network
Management Protocol (SNMPv2)", RFC 1442, SNMP Research, Inc.,
Hughes LAN Systems, Dover Beach Consulting, Inc., Carnegie Mellon
University, April 1993.
[2] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Textual
Conventions for version 2 of the the Simple Network Management
Protocol (SNMPv2)", RFC 1443, SNMP Research, Inc., Hughes LAN
Systems, Dover Beach Consulting, Inc., Carnegie Mellon
University, April 1993.
[3] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser,
"Conformance Statements for version 2 of the the Simple Network
Management Protocol (SNMPv2)", RFC 1444, SNMP Research, Inc.,
Hughes LAN Systems, Dover Beach Consulting, Inc., Carnegie Mellon
University, April 1993.
[4] Galvin, J., and K. McCloghrie, "Administrative Model for version
2 of the Simple Network Management Protocol (SNMPv2)", RFC 1445,
Trusted Information Systems, Hughes LAN Systems, April 1993.
[5] Case, J., McCloghrie, K., Rose, M., and S. Waldbusser, "Protocol
Operations for version 2 of the Simple Network Management
Protocol (SNMPv2)", RFC 1448, SNMP Research, Inc., Hughes LAN
Systems, Dover Beach Consulting, Inc., Carnegie Mellon
University, April 1993.
[6] McCloghrie, K., and M. Rose, "Management Information Base for
Network Management of TCP/IP-based internets: MIB-II", STD 17,
RFC 1213, Hughes LAN Systems, Inc., Performance Systems
International, March 1991.
[7] Information processing systems - Open Systems Interconnection -
Specification of Abstract Syntax Notation One (ASN.1),
International Organization for Standardization. International
Standard 8824, (December, 1987).
[8] Information processing systems - Open Systems Interconnection -
Specification of Basic Encoding Rules for Abstract Notation One
(ASN.1), International Organization for Standardization.
International Standard 8825, (December, 1987).
[9] American National Standard for Telecommunications - Digital
Hierarchy - Optical Interface Rates and Formats Specification,
ANSI T1.105-1988.
AToM MIB Working Group [Page 57]
RFC 1595 SONET/SDH Objects March 1994
[9a] ANSI T1.105-1991.
[10] American National Standard for Telecommunications - Digital
Hierarchy - Optical Interface Specification (Single-Mode), ANSI
T1.106-1988.
[11] American National Standard for Telecommunications -- Layer 1 In-
Service Digital Transmission Performance Monitoring T1M1.3/93-
005R2, July 1993.
[12] McCloghrie, K., and F. Kastenholz, "Evolution of Interfaces
Group of MIB-II", RFC 1573, Hughes LAN Systems, FTP Software,
January 1994.
[13] Cox, T., and K. Tesink, Editors, "Definitions of Managed Objects
for the DS3/E3 Interface Type", RFC 1407, Bellcore, January 1993.
[14] Baker, F., and J. Watt, Editors, "Definitions of Managed Objects
for the DS1/E1 Interface Type", RFC 1406, Advanced Computer
Communications, Newbridge Networks Corporation, January 1993.
[15] CCITT Recommendation G.707, "Synchronous Digital Hierarchy Bit
Rates", June 1992.
[16] CCITT Recommendation G.708, "Network Node Interface for the
Synchronous Digital Hierarchy", June 1992.
[17] CCITT Recommendation G.709, "Synchronous Multiplexing Structure",
June 1992.
[18] CCITT Recommendation G.783, "Characteristics of Synchronous
Digital Hierarchy (SDH) Multiplexing Equipment Functional
Blocks", November 1992.
AToM MIB Working Group [Page 58]
RFC 1595 SONET/SDH Objects March 1994
Tracy A. Brown
Bell Communications Research
331 Newman Springs Road
P.O. Box 7020
Red Bank, NJ 07701-7020
Phone: (908) 758-2107
EMail: tacox@mail.bellcore.com
Kaj Tesink
Bell Communications Research
331 Newman Springs Road
P.O. Box 7020
Red Bank, NJ 07701-7020
Phone: (908) 758-5254
EMail: kaj@cc.bellcore.com
AToM MIB Working Group [Page 59]