Network Working Group S. Yeh
Request for Comments: 1204 D. Lee
Netix Communications, Inc.
February 1991
Message Posting Protocol (MPP)
Status of this Memo
This memo describes a protocol for posting messages from workstations
(e.g., PCs) to a mail service host. This RFC specifies an
Experimental Protocol for the Internet community. Discussion and
suggestions for improvement are requested. Please refer to the
current edition of the "IAB Official Protocol Standards" for the
standardization state and status of this protocol. Distribution of
this memo is unlimited.
Operating systems for personal computers do not provide a mechanism
for user authentication. However, such a mechanism is crucial for
electronic mail system since authenticating message sender's identity
is important in preventing mail forgery. Hence, adding personal
computers to an electronic mail network requires an agent (message
posting server) to authenticate sender's identity and then submit
mail to the message delivery system (e.g., Sendmail, MMDF) on behalf
of the sender at a PC. The Netix Message Posting Protocol is
developed to be the interface between the message posting server and
the PC (client). The protocol is designed to use TCP and is based on
the command and reply structures defined for Simple Mail Transfer
Protocol (RFC 821) and File Transfer Protocol (RFC 959).
USER <SP> <username> <CRLF>
The USER command informs the message posting server about the
username of the user trying to submit mail to the network. The
required argument for the USER command is a string specifying
the message sender's username.
The USER command can only be used under three conditions:
- when the session with the message posting server has just
started;
- right after a message text (terminated by the "<CRLF>.<CRLF>"
sequence) has been successfully submitted to the message
posting server;
- right after a USER command that gets the reply code 501.
List of possible reply codes for the USER command:
- 250 The username of the message sender has been accepted.
- 451 Internal error has occurred in the message posting
server.
- 501 Syntax error detected in the username argument.
- 503 The USER command has been used under an inappropriate
condition (i.e., one that is not specified above).
It is recommended that the message posting server should return
250 even if the username is not recognized by the message
posting server, as long as the username is syntactically
correct. This is an attempt to prevent the message posting
server from releasing too much information about the user
database. Client should not be able to test the existence of a
certain username.
Yeh & Lee [Page 2]
RFC 1204 MPP February 1991
PASS <SP> <password> <CRLF>
The PASS command is used to inform the message posting server
about the password associated with the username previously
specified. The required argument for the PASS command is a
string specifying the message sender's password.
The PASS command can only be used under two conditions:
- right after a USER command that gets the reply code 250;
- right after a PASS command that gets the reply code 501.
List of possible reply codes for the PASS command:
- 250 The password has been accepted and verified to be
correctly associated with the username previously
specified.
- 451 Internal error has occurred in the message posting
server.
- 501 Syntax error detected in the password argument.
- 503 The PASS command has been used under an inappropriate
condition (i.e., one that is not specified above).
- 530 The password provided is not the one associated with the
username previously specified.
DATA <CRLF>
The DATA command is used to inform the message posting server
to get ready to accept a mail message text. No argument is
expected. (This command has the same meaning as the DATA
command defined in RFC 821.)
The DATA command can only be used under two conditions:
- right after a PASS command that gets the reply code 250;
- right after a mail message text has been successfully
accepted from the client.
List of possible reply codes for the DATA command:
- 354 The message posting server is ready to accept the mail
message text.
Yeh & Lee [Page 3]
RFC 1204 MPP February 1991
- 451 Internal error has occurred in the message posting
server.
- 503 The DATA command has been used under an inappropriate
condition (i.e., one that is not specified above).
Upon receiving the reply code 354 for the DATA command, the
client should submit the mail message text to message posting
server and terminate the text by the sequence "<CRLF>.<CRLF>"
as defined in RFC 821. If the message text includes the
"<CRLF>.<CRLF>" sequence, then the sequence is replaced by the
"<CRLF>..<CRLF>" sequence as defined in RFC 821. The extra "."
token will not be included in the final copy of the submitted
message.
Upon receiving the mail message text terminated by the
"<CRLF>.<CRLF>" sequence, list of possible reply codes is:
- 250 The mail message text has been successfully queued for
delivery.
- 451 Internal error has occurred in the message posting
server and the mail message text has not been queued.
NOOP <CRLF>
The NOOP command does not cause any action to be performed by
the message posting server. Instead, it tests the status of
the message posting server. No argument is expected.
The NOOP command cannot be used under one condition:
- right after a DATA command that gets the reply code 354
(i.e., when the message posting server is expecting the client
to submit the mail message text).
List of possible reply codes for the NOOP command:
- 250 The message posting server has not encountered any
internal error.
- 451 Internal error has occurred in the message posting
server during the current session.
QUIT <CRLF>
The QUIT command is used to terminate the session with the
message posting server. No argument is expected.
Yeh & Lee [Page 4]
RFC 1204 MPP February 1991
The QUIT command can be used under any condition. The message
posting server should always return the reply code 221 for the
QUIT command.
There are several issues to be considered when implementing the
message posting server:
- secured environment
- port number assignment
- handling of idle client
- local/remote password database
- message queuing
- handling of message delivery failure
The message posting server is responsible for authenticating message
senders and submitting mail to the message delivery system. Hence,
it should be running in a secured environment, such as running on a
system (UNIX, VMS, MS-DOS) with well restricted physical and network
access.
To take advantage of existing password databases, such as the passwd
file in UNIX, the message posting server can use FTP and POP3 to
perform the username and password checking with the appropriate
server.
For network that does not have any password database, the message
posting server should let the system administrator specify a local
password file on the host that the message posting server is running.
Yeh & Lee [Page 5]
RFC 1204 MPP February 1991
[1] Postel, J., "Simple Mail Transfer Protocol", RFC 821,
USC/Information Sciences Institute, August 1982.
[2] Postel, J., and J. Reynolds, "File Transfer Protocol", RFC 959,
USC/Information Sciences Institute, October 1985.
Security Considerations
Security issues are discussed in section 3.1.
Authors' Addresses
Shannon Yeh
Netix Communications, Inc.
15375 Barranca Parkway, Suite A-215
Irvine, CA 92718
Phone: (714) 727-9335
Email: yeh@netix.com
David Lee
Netix Communications, Inc.
15375 Barranca Parkway, Suite A-215
Irvine, CA 92718
Phone: (714) 727-9335
EMail: dlee@netix.com
Yeh & Lee [Page 6]