28.1.1 Macros in Rules

Each noncomment part of a rule is expanded as the configuration file is read. [1] Thus any references to defined macros are replaced with the value that the macro has at that point in the configuration file. To illustrate, consider this mini-configuration file (called x.cf ):

[1] Actually, the comment part is expanded too, but with no effect other than a tiny expenditure of time.

DAvalue1
R$A    $A.new
DAvalue2
R$A    $A.new

In it, $A will have the value value1 when the first R line is expanded and value2 when the second is expanded. Prove this to yourself by running sendmail in -bt rule-testing mode on that file:

% 

echo =S0 | /usr/lib/sendmail -bt -Cx.cf


> =S0
Rvalue1                 value1 . new 
Rvalue2                 value2 . new

Here, we use the =S command (see Section 38.4.1, "Show Rules in a Rule Set with =S" ) to show each rule after it has been read and expanded.

Another property of macros is that an undefined macro expands to an empty string. Consider this x.cf file:

DAvalue1
R$A    $A.$B
DAvalue2
R$A    $A.$B

and this rule-testing run of sendmail :

% 

echo =S0 | /usr/lib/sendmail -bt -Cx.cf


> =S0
Rvalue1                 value1 . 
Rvalue2                 value2 .

Beginning with V8.7 sendmail , macros can be either single-character or multicharacter. Both forms are expanded when the configuration file is read:

D{OURDOMAIN}us.edu
R${OURDOMAIN}    localhost.${OURDOMAIN}

Multicharacter macros may be used in the LHS and in the RHS . When the configuration file is read, the previous example is expanded to look like this:

> =S0
Rus . edu               localhost . us . edu

28.1.2 Rules Are Treated Like Addresses

After each side ( LHS and RHS ) is expanded, each is then normalized just as though it were an address. A check is made for any tabs that may have been introduced during expansion. If any are found, everything from the first tab to the end of the string is discarded. Then RFC822 -style comments are removed. An RFC822 comment is anything between and including an unquoted pair of parentheses:

DAroot@my.site (Operator)
R$A  
tab


 


RHS

  


Rroot@my.site (Operator)  
tab


 


RHS

 expanded

  


Rroot@my.site  
tab


 


RHS

 RFC822 comment stripped

Finally, a check is made for balanced quotation marks, right parentheses balanced by left, and right angle brackets balanced by left. [2] If any right-hand character appears without a corresponding left-hand character, sendmail prints one of the following errors, where configfile is the name of the configuration file that is being read, num shows the line number in that file, and expression is the part of the rule that was unbalanced:

[2] The $> operator isn't counted in checking balance.

configfile: line 


num: expression...Unbalanced '"'



configfile: line 


num: expression...Unbalanced '>'



configfile: line 


num: expression...Unbalanced ')'

The first line shows that sendmail has balanced the unbalanced quotation mark by appending a second quotation mark. Each of the last two lines shows that the unbalanced character is removed. For example, the file:

Rx      RHS"
Ry      RHS>
Rz      RHS)

produces these errors and rules:

% 

echo =S0 | /usr/lib/sendmail -bt -Cx.cf


x.cf: line 1: RHS"... Unbalanced '"'
x.cf: line 2: RHS>... Unbalanced '>'
x.cf: line 3: RHS)... Unbalanced ')'
> =S0
Rx              RHS "" 
Ry              RHS 
Rz              RHS

Note that prior to V8.7 sendmail , only an unbalanced right-hand character was checked: [3] Beginning with V8.7 sendmail , unbalanced left-hand characters are also detected, and sendmail attempts to balance them for you. Consider, the following file:

[3] That is, for example, there must not be a > before the < character, and they must pair off.

Rx      "RHS
Ry      <RHS
Rz      (RHS

Here, sendmail detects and fixes the unbalanced characters but does so with warnings:

% 

echo =S0 | /usr/lib/sendmail -bt -Cx.cf


x.cf: line 1: "RHS... Unbalanced '"'
x.cf: line 2: <RHS... Unbalanced '<'
x.cf: line 3: (RHS... Unbalanced '('
x.cf: line 3: R line: null RHS
> =S0
Rx              "RHS" 
Ry              < RHS > 
Rz

Note that in the last example ( Rz ), sendmail balanced the RHS by adding a rightmost parenthesis. This caused the RHS to become an RFC822 comment, which was then deleted, resulting in the null RHS error.

If you get one of these Unbalanced errors, be sure to correct the problem at once. If you leave the faulty rule in place, sendmail will continue to run but will likely produce erroneous mail delivery and other odd problems.