There are two BOOTP servers available for GNU/Linux. The first is CMU bootpd. The other is actually a DHCP server: ISC dhcpd. In Ubuntu these are contained in the bootp and dhcp3-server packages respectively.

To use CMU bootpd, you must first uncomment (or add) the relevant line in /etc/inetd.conf. On Debian GNU/Linux or Ubuntu, you can run update-inetd --enable bootps, then /etc/init.d/inetd reload to do so. Just in case your BOOTP server does not run Debian or Ubuntu, the line in question should look like:

Now, you must create an /etc/bootptab file. This has the same sort of familiar and cryptic format as the good old BSD printcap, termcap, and disktab files. See the bootptab manual page for more information. For CMU bootpd, you will need to know the hardware (MAC) address of the client. Here is an example /etc/bootptab:

You will need to change at least the “ha” option, which specifies the hardware address of the client. The “bf” option specifies the file a client should retrieve via TFTP; see the section called “Move TFTP Images Into Place” for more details.

By contrast, setting up BOOTP with ISC dhcpd is really easy, because it treats BOOTP clients as a moderately special case of DHCP clients. Some architectures require a complex configuration for booting clients via BOOTP. If yours is one of those, read the section the section called “Setting up a DHCP server”. In that case, you will probably be able to get away with simply adding the allow bootp directive to the configuration block for the subnet containing the client, and restart dhcpd with /etc/init.d/dhcpd3-server restart.

One free software DHCP server is ISC dhcpd. For Ubuntu, the dhcp3-server package is recommended. Here is a sample configuration file for it (see /etc/dhcp3/dhcpd.conf):

In this example, there is one server servername which performs all of the work of DHCP server, TFTP server, and network gateway. You will almost certainly need to change the domain-name options, as well as the server name and client hardware address. The filename option should be the name of the file which will be retrieved via TFTP.

After you have edited the dhcpd configuration file, restart it with /etc/init.d/dhcpd3-server restart.

To get the TFTP server ready to go, you should first make sure that tftpd is enabled. This is usually enabled by having something like the following line in /etc/inetd.conf:

Ubuntu packages will in general set this up correctly by default when they are installed.

	Historically, TFTP servers used /tftpboot as directory to serve images from. However, Debian GNU/Linux packages may use other directories to comply with the Filesystem Hierarchy Standard. For example, tftpd-hpa by default uses /var/lib/tftpboot. You may have to adjust the configuration examples in this section accordingly.

Look in /etc/inetd.conf and remember the directory which is used as the argument of in.tftpd^[2]; you'll need that below. If you've had to change /etc/inetd.conf, you'll have to notify the running inetd process that the file has changed. On an Ubuntu or Debian machine, run /etc/init.d/inetd reload; on other machines, find out the process ID for inetd, and run kill -HUP inetd-pid.

Next, place the TFTP boot image you need, as found in the section called “Where to Find Installation Images”, in the tftpd boot image directory. You may have to make a link from that file to the file which tftpd will use for booting a particular client. Unfortunately, the file name is determined by the TFTP client, and there are no strong standards.

For PXE booting, everything you should need is set up in the netboot/netboot.tar.gz tarball. Simply extract this tarball into the tftpd boot image directory. Make sure your dhcp server is configured to pass /ubuntu-installer/ia64/elilo.efi to tftpd as the filename to boot.