|PostgreSQL 8.2.6 Documentation|
|Prev||Fast Backward||Chapter 17. Server Configuration||Fast Forward||Next|
See also Section 27.3 for details on WAL tuning.
If this parameter is on, the
server will try to make sure that updates are physically written to disk, by issuing
system calls or various equivalent methods (see
). This ensures that the database cluster can recover to a consistent state after an operating system or hardware crash.
However, using fsync results in a performance penalty: when a transaction is committed, PostgreSQL must wait for the operating system to flush the write-ahead log to disk. When fsync is disabled, the operating system is allowed to do its best in buffering, ordering, and delaying writes. This can result in significantly improved performance. However, if the system crashes, the results of the last few committed transactions may be lost in part or whole. In the worst case, unrecoverable data corruption may occur. (Crashes of the database software itself are not a risk factor here. Only an operating-system-level crash creates a risk of corruption.)
Due to the risks involved, there is no universally correct setting for fsync . Some administrators always disable fsync , while others only turn it off during initial bulk data loads, where there is a clear restart point if something goes wrong. Others always leave fsync enabled. The default is to enable fsync , for maximum reliability. If you trust your operating system, your hardware, and your utility company (or your battery backup), you can consider disabling fsync .
This parameter can only be set in the postgresql.conf file or on the server command line. If you turn this parameter off, also consider turning off full_page_writes .
Method used for forcing WAL updates out to disk. If fsync is off then this setting is irrelevant, since updates will not be forced out at all. Possible values are:
(write WAL files with
at each commit)
at each commit, forcing write-through of any disk write cache)
at each commit)
(write WAL files with
Not all of these choices are available on all platforms. The default is the first method in the above list that is supported by the platform. The open_ * options also use O_DIRECT if available. This parameter can only be set in the postgresql.conf file or on the server command line.
When this parameter is on, the PostgreSQL server writes the entire content of each disk page to WAL during the first modification of that page after a checkpoint. This is needed because a page write that is in process during an operating system crash might be only partially completed, leading to an on-disk page that contains a mix of old and new data. The row-level change data normally stored in WAL will not be enough to completely restore such a page during post-crash recovery. Storing the full page image guarantees that the page can be correctly restored, but at a price in increasing the amount of data that must be written to WAL. (Because WAL replay always starts from a checkpoint, it is sufficient to do this during the first change of each page after a checkpoint. Therefore, one way to reduce the cost of full-page writes is to increase the checkpoint interval parameters.)
Turning this parameter off speeds normal operation, but might lead to a corrupt database after an operating system crash or power failure. The risks are similar to turning off fsync , though smaller. It may be safe to turn off this parameter if you have hardware (such as a battery-backed disk controller) or file-system software that reduces the risk of partial page writes to an acceptably low level (e.g., ReiserFS 4).
Turning off this parameter does not affect use of WAL archiving for point-in-time recovery (PITR) (see Section 23.3 ).
This parameter can only be set in the postgresql.conf file or on the server command line. The default is on .
The amount of memory used in shared memory for WAL data. The default is 64 kilobytes ( 64kB ). The setting need only be large enough to hold the amount of WAL data generated by one typical transaction, since the data is written out to disk at every transaction commit. This parameter can only be set at server start.
Increasing this parameter may cause PostgreSQL to request more System V shared memory than your operating system's default configuration allows. See Section 16.4.1 for information on how to adjust those parameters, if necessary.
Time delay between writing a commit record to the WAL buffer and flushing the buffer out to disk, in microseconds. A nonzero delay can allow multiple transactions to be committed with only one
system call, if system load is high enough that additional transactions become ready to commit within the given interval. But the delay is just wasted if no other transactions become ready to commit. Therefore, the delay is only performed if at least
other transactions are active at the instant that a server process has written its commit record. The default is zero (no delay).
Minimum number of concurrent open transactions to require before performing the commit_delay delay. A larger value makes it more probable that at least one other transaction will become ready to commit during the delay interval. The default is five transactions.
Maximum distance between automatic WAL checkpoints, in log file segments (each segment is normally 16 megabytes). The default is three segments. This parameter can only be set in the postgresql.conf file or on the server command line.
Maximum time between automatic WAL checkpoints, in seconds. The default is five minutes ( 5min ). This parameter can only be set in the postgresql.conf file or on the server command line.
Write a message to the server log if checkpoints caused by the filling of checkpoint segment files happen closer together than this many seconds (which suggests that checkpoint_segments ought to be raised). The default is 30 seconds ( 30s ). Zero disables the warning. This parameter can only be set in the postgresql.conf file or on the server command line.
The shell command to execute to archive a completed segment of the WAL file series. If this is an empty string (the default), WAL archiving is disabled. Any %p in the string is replaced by the path name of the file to archive, and any %f is replaced by the file name only. (The path name is relative to the working directory of the server, i.e., the cluster's data directory.) Use %% to embed an actual % character in the command. For more information see Section 23.3.1 . This parameter can only be set in the postgresql.conf file or on the server command line.
It is important for the command to return a zero exit status if and only if it succeeds. Examples:
archive_command = 'cp "%p" /mnt/server/archivedir/"%f"' archive_command = 'copy "%p" /mnt/server/archivedir/"%f"' # Windows
The archive_command is only invoked on completed WAL segments. Hence, if your server generates little WAL traffic (or has slack periods where it does so), there could be a long delay between the completion of a transaction and its safe recording in archive storage. To put a limit on how old unarchived data can be, you can set archive_timeout to force the server to switch to a new WAL segment file periodically. When this parameter is greater than zero, the server will switch to a new segment file whenever this many seconds have elapsed since the last segment file switch. Note that archived files that are closed early due to a forced switch are still the same length as completely full files. Therefore, it is unwise to use a very short archive_timeout — it will bloat your archive storage. archive_timeout settings of a minute or so are usually reasonable. This parameter can only be set in the postgresql.conf file or on the server command line.