[OpenBSD]

[3.4 -> 3.5] | [3.5 -> 3.6] | [FAQ Index] | [3.7 -> 3.8]

Upgrade Guide: 3.6 to 3.7


Note: Upgrades are only supported from one release to the release immediately following it. Do not skip releases.

Upgrading is a convenient way to bring your OpenBSD system up to the most recent version. However, the results are not intended to precisely match the results of a wipe-and-reload installation. Old library files in particular are not removed in the upgrade process, as they may be required by older applications that may or may not be upgraded at this time. If you REALLY wish to get rid of all these old files, you would probably be better off reinstalling from scratch.

Before upgrading...

Before upgrading, some users choose to remove all packages, and installing new versions after upgrade. If your platform is one of those that switched to gcc3 (macppc, i386), you SHOULD probably do this.

To quickly remove all packages from your system:

pkg_delete -q /var/db/pkg/*
After the upgrade, install the new versions of these applications.

Note that, with OpenBSD 3.7, the pkg tools now support in-place updating using pkg_add -r. This has been checked to work with most packages, in particular with the CD packages available in 3.5 or 3.6. Some important points apply:

i386 and macppc users: Due to the switch to gcc3, you must remove the /usr/include/g++ directory before upgrading, regardless whether you plan to use the install media or not:

rm -rf /usr/include/g++

Upgrading by install media

The easiest and safest way to upgrade from binary files is to boot from install media and follow the upgrade steps, which are very similar to the install process. Afterwards, do the /etc updates below.

Upgrading without install media

This is not the recommended process. Use the install media method if at all possible!

Sometimes, one needs to do an upgrade of a machine when one can't easily use the normal upgrade process. One can usually do this by carefully following a process similar to a source-based upgrade:

During this process, sendmail(8) may produce some error messages like the following: Nov 1 12:47:05 puffy sm-mta[16733]: filesys_update failed: No such file or dire ctory, fs=., avail=-1, blocksize=380204 These messages can be safely ignored, or you may wish to halt sendmail(8) during the upgrade process.

Updates to /etc

Whether you upgrade by using an install media and doing a formal "upgrade" process, or do a "in-place" binary upgrade, there are certain manual steps that have to be performed.

New users and groups

The FTP daemon has been reworked to drop privileges, and an OSPF daemon has been added, so new users and groups are required. As root, add the following users and groups, using useradd(8):
useradd -u84 -g=uid -c"FTP Daemon" -d/var/empty -s/sbin/nologin _ftp useradd -u85 -g=uid -c"OSPF Daemon" -d/var/empty -s/sbin/nologin _ospfd
These steps will add both the new users and their corresponding groups. Your environment may allow you to copy/paste those commands.

Userland Applications

X.org replaces XFree86: Due the XFree86 project's change of license, OpenBSD has switched to the X.org project's X Window System. The X11 configuration files must be updated, however. Many users can simply unpack xetc37.tgz without concern:

cd / tar xzpf /path/xetc37.tgz
If you have made important manual changes to the files in /etc/X11 for any reason, you should NOT unpack the xetc37.tgz file as above, but rather manually merge your changes into the new files.

If you have an /etc/X11/XF86Config file that works on OpenBSD 3.6, renaming it to /etc/X11/xorg.conf will probably give you a fully functioning X Window system on OpenBSD 3.7. You may also find that the newer versions of X are much more "self-configuring" than earlier versions, and you may not need an /etc/X11/xorg.conf file at all now, depending on your hardware.

bgpd(8) behavior change: The new rde route-age [evaluate|ignore] changed behavior of bgpd. Until now evaluate was the implicit default but now the default is ignore. Route age evaluation is not specified in RFC 1771 and results in non deterministic decisions in preference for more stable links.

pfsync takes syncdev instead of syncif: When configuring the pfsync device, use 'syncdev' instead of the deprecated keyword 'syncif'.

OpenNTPD now sets the time immediately at startup: As of OpenBSD 3.7, OpenNTPD is able to make large time corrections, so it is no longer necessary to run rdate(8) to set the time before starting ntpd(8). You may wish to disable rdate(8) in your rc.conf.local (or rc.conf) file if you had opted to do this.

/etc file changes

You will want to extract the etc37.tgz files to a temporary location:
cd /tmp tar xzpf /path/etc37.tgz
Files that can probably be copied from etc37.tgz "as is":
changelist daily fbtab moduli netstart ospfd.conf rc security services mtree/*
Note that it IS possible to locally modify these files, if this has been done, manual merging will be needed. Here are copy/paste lines for copying these files, assuming you unpacked etc37.tgz in the above recommended place:
cd /tmp/etc cp changelist daily fbtab moduli netstart ospfd.conf rc security services /etc cp mtree/* /etc/mtree/

Files that must be manually merged, respecting any local changes made to them, if they were modified from the default, otherwise, just copy them over, too:

ftpusers rc.conf spamd.conf sysctl.conf mail/aliases skel/.cshrc skel/.profile
Finally, use mtree(8) to create any new directories:
mtree -qdef /etc/mtree/4.4BSD.dist -p / -u

[3.4 -> 3.5] | [3.5 -> 3.6] | [FAQ Index] | [3.7 -> 3.8]


[back] www@openbsd.org
$OpenBSD: upgrade37.html,v 1.14 2005/11/22 16:53:48 steven Exp $