Upgrade Guide: 3.5 to 3.6

Note: Upgrades are only supported from release to release, it is recommended that you NOT skip releases.

Before upgrading...

Before upgrading, some users choose to remove all packages, and installing new versions after upgrade.

To quickly remove all packages from your system:

pkg_delete -q /var/db/pkg/*

After the upgrade, install the new versions of these applications.

Upgrading by install media

The easiest and safest way to upgrade from binary files is to boot from install media and follow the upgrade steps, which are very similar to the install process. Afterwards, do the /etc updates below.

Upgrading without install media

This is not the recommended process. Use the install media method if at all possible!

Sometimes, one needs to do an upgrade of a machine when one can't easily use the normal upgrade process. One can usually do this by carefully following a process similar to a source-based upgrade:

Place install files in a "good" location. Make sure you have sufficient room!
Install new kernel(s)
cd /path rm /obsd ; ln /bsd /obsd && cp bsd /nbsd && mv /nbsd /bsd cp bsd.rd bsd.mp /
Note the extra steps for copying over the primary kernel: those are done to ensure that there is always a valid copy of the kernel on the disk that the system can boot from should there be a really badly timed power outage or system crash.
Reboot on the new kernel
This might be a tempting step to skip, but it should be done now, as usually, the new kernel will run old userland apps (such as the soon to be important reboot!), but often a new userland will NOT work on the old kernel.
Stop any applications which might cause problems in the following steps.
Install new userland applications
cd / tar xzpf /path/base36.tgz tar xzpf /path/comp36.tgz tar xzpf /path/game36.tgz tar xzpf /path/man36.tgz tar xzpf /path/misc36.tgz tar xzpf /path/xbase36.tgz tar xzpf /path/xfont36.tgz tar xzpf /path/xserv36.tgz tar xzpf /path/xshare36.tgz
Note: not all file sets will need to be installed for all applications, however, if you installed a file set originally, you should certainly upgrade it with the new file sets now. Also note that etc36.tgz and xetc36.tgz are NOT unpacked here, as they are handled separately.
Update /dev. The new MAKEDEV file will be copied to /dev by the installation of base36.tgz, so you simply need to do the following:
cd /dev ./MAKEDEV all
Also see any version-specific notes below.
Upgrade /etc as below.
Reboot

During this process, sendmail(8) may produce some error messages like the following:


    Nov 1 12:47:05 puffy sm-mta[16733]: filesys_update failed: No such file or dire
    ctory, fs=., avail=-1, blocksize=380204

These messages can be safely ignored, or you may wish to halt sendmail(8) during the upgrade process.

Updates to `/etc`

Whether you upgrade by using an install media and doing a formal "upgrade" process, or do a "in-place" binary upgrade, there are certain manual steps that have to be performed.

New users and groups

A number of daemons have been reworked to drop privilege or use privilege separation, thus new users and groups are required. As root, add the following users and groups, using useradd(8):

useradd -u77 -g=uid -c"DHCP programs" -d/var/empty -s/sbin/nologin _dhcp useradd -u78 -g=uid -c"MOP Daemon" -d/var/empty -s/sbin/nologin _mopd useradd -u79 -g=uid -c"TFTP Daemon" -d/var/empty -s/sbin/nologin _tftpd useradd -u80 -g=uid -c"rbootd Daemon" -d/var/empty -s/sbin/nologin _rbootd useradd -u81 -g=uid -c"afs Daemon" -d/var/empty -s/sbin/nologin _afs useradd -u82 -g=uid -c"PPP utilities" -d/var/empty -s/sbin/nologin _ppp useradd -u83 -g=uid -c"NTP Daemon" -d/var/empty -s/sbin/nologin _ntp

These steps will add both the new users and their corresponding groups. Your environment may allow you to cut/paste those commands.

Devices

Due to the new handling of pty(4) there will be some old devices that should be deleted:

cd /dev && rm -f [pt]ty[rq]*

or on the VAX platform:

cd /dev && rm -f [pt]tyr*

Userland Applications

The cksum(1) utility has moved from /usr/bin to /bin.

rm -f /usr/bin/cksum /usr/bin/sum

Users of authpf(8) must change their anchor rule in the main ruleset from

anchor authpf

anchor "authpf/*"

`/etc` file changes

You will want to extract the etc36.tgz files to a temporary location:

cd /tmp tar xzpf /path/etc36.tgz

Files that can probably be copied from etc36.tgz "as is":

changelist magic netstart ntpd.conf pf.os protocols rc rc.securelevel services mtree/* systrace/*

Note that it IS possible to locally modify these files, if this has been done, manual merging will be needed. Here are copy/paste lines for copying these files, assuming you unpacked etc36.tgz in the above recommended place:

cd /tmp/etc cp changelist magic netstart ntpd.conf pf.os protocols rc rc.securelevel services /etc cp mtree/* /etc/mtree/ cp systrace/* /etc/systrace/

Files that must be manually merged, respecting any local changes made to them:

bgpd.conf ftpusers inetd.conf login.conf lynx.cfg rc.conf rc.local remote sysctl.conf ttys

Finally, use mtree(8) to create any new directories:

mtree -qdef /etc/mtree/4.4BSD.dist -p / -u

[3.4 -> 3.5] [FAQ Index] [3.6 -> 3.7]

www@openbsd.org
$OpenBSD: upgrade36.html,v 1.13 2005/05/19 16:58:39 nick Exp $