Table B-2 Cisco ATA Voice Menu Codes—Configuration Parameters
Option
|
Voice Menu Code
|
Description
|
Alternate NTP IP address
|
78
|
IP address of the alternate NTP server
|
Audio mode
|
312
|
Allows finer control of the audio component to suit certain user applications
|
Call features
|
314
|
Subscribed features statically enabled by the user
|
Caller ID method
|
316
|
Specifies the signal format when generating the Caller ID format to use
|
TFTP Configuration Interval
|
80002
|
Interval (in seconds) between configuration updates when TFTP configuration is used,
|
Connection mode
|
311
|
Controls the connection mode of the call signaling protocol
|
Dynamic Host Configuration Protocol (DHCP)
|
20
|
Controls whether the Cisco ATA can automatically obtain configuration parameters from a server over the network
|
DNS 1 IP
|
916
|
IP address of the primary DNS server
|
DNS 2 IP
|
917
|
IP address of the secondary DNS server
|
Encrypt key
|
320
|
Encrypts the configuration file on the TFTP server
|
Num Tx frames
|
35
|
Number of frames transmitted per packet
|
Gatekeeper/proxy server IP address
|
5
|
SIP registration proxy server IP address
|
IP address
|
1
|
IP address of the Cisco ATA
|
LBR codec
|
300
|
Low bit rate codec selection
|
Login ID 0
|
46
|
Alternate user ID used for authentication
|
Login ID 1
|
47
|
Alternate user ID used for authentication
|
Media port
|
202
|
Specifies which base port the Cisco ATA uses to receive RTP media streams
|
Network route address
|
2
|
Network router address
|
NPrintf address
|
81
|
IP address of a host to which all Cisco ATA debug messages are sent
|
NTP server address
|
141
|
IP address of the NTP server
|
Paid features
|
315
|
Features subscribed to by the user
|
Polarity
|
304
|
Controls connect and disconnect polarity
|
PWD 0
|
4
|
Password associated with the primary phone line (UID0 or LoginID0)
|
PWD 1
|
14
|
Password associated with the secondary phone line (UID1 or LoginID1)
|
Rx codec
|
36
|
Selects the audio codec type to use to decode received data. The call-receiving station automatically adjusts to the call-initiating station's audio codec type if the call-receiving station supports that audio codec.
|
Set password
|
7387277
|
Configuration interface password
|
Signal timers
|
318
|
Timeout values controlling the starting or stopping of a signaling event
|
SIP max number of redirects
|
205
|
Maximum number of redirections the Cisco ATA will attempt to reach a callee when making a call
|
SIP NAT IP address
|
200
|
WAN IP of the NAT
|
SIP outbound proxy
|
206
|
IP address of the outbound proxy server to which all outgoing SIP requests are sent
|
SIP port
|
201
|
Specifies which port the Cisco ATA listens to for incoming SIP messages
|
SIP protocol
|
38
|
Selects the signaling protocol
|
SIP registration On
|
204
|
Enables SIP registration
|
SIP registration period
|
203
|
Interval (in seconds) between each registration renewal to the SIP registration server
|
Subnet mask
|
10
|
Specifies the subnet mask for the Cisco ATA
|
TFTP URL
|
905
|
IP address of the TFTP server when TFTP configuration is used
|
Timezone
|
302
|
Specifies offset to GMT—used to time-stamp incoming calls for caller ID
|
ToConfig
|
80001
|
Identifies unconfigured or already-configured Cisco ATAs
|
Trace Fflags
|
313
|
Enables logging of debug information
|
Tx Codec
|
37
|
Selects transmitting audio codec preference
|
UDP TOS bits
|
255
|
Determines the precedence and delay of UDP IP packets
|
UID 0
|
3
|
User ID (telephone number) for the PHONE 1 port
|
UID 1
|
13
|
User ID (telephone number) for the PHONE 2 port
|
Use login ID
|
93
|
Determines which pair (UIDx, PWDx or LoginIDx, PWDx) to use for authentication
|
Use TFTP
|
305
|
Enables TFTP as configuration method
|
Table B-1—Information Options
