|
|
This chapter describes the configuration for the Four Span T1, Four Span E1, and MVDC-T1 programmable trunk cards.
Use the programmable trunk card group to configure individual ports on programmable Four Span T1, Four Span E1, and MVDCT1 trunk cards. This group consists of the following tables:
The Four Span T1, Four Span E1, and MVDC-T1 cards provide programmable trunks. With the programmable trunk card table you can modify span configuration and port signaling options, and access the Trunk Timing Configuration screen. This section lists the objects within the programmable trunk card table.
{ptc 1}
Description
List of the programmable trunk cards including 4XT1, 4XE1, and MVDC-T1.
Object Identifier
1.3.6.1.4.1.886.1.4.1
Data Type
Sequence of PtcSpanEntry
Access Policy
Not accessible
Status
Mandatory
{ptcSpanTable 1}
Description
An entry in the ptcSpanTable.
Object Identifier
1.3.6.1.4.1.886.1.4.1.1
Data Type
PtcSpanEntry
Access Policy
Not accessible
Status
Mandatory
Index
{ptcIndex, ptcType, ptcSpanNum}
Sequence
ptcIndex | CardIndex |
ptcType | Integer |
ptcRack | Integer |
ptcLevel | Integer |
ptcSlot | Integer |
ptcSpanNum | Integer |
ptcTxGain | Integer |
ptcRxGain | Integer |
ptcTxClck | Integer |
ptcRfClck | Integer |
ptcSpanType | Integer |
ptcSlip | Integer |
ptcOutOfFrame | Integer |
ptcLaw | Integer |
ptcCode | Integer |
ptcLeng | Integer |
ptcCrc | Integer |
ptcTs0 | Integer |
ptcTs16 | Integer |
ptcStatus | Integer |
ptcUnusedPorts | Integer |
ptcRevVer | DisplayString |
ptcPhyAdd | Integer |
ptcNfasGrpIndex | Integer |
ptcNfasGrpPosition | Integer |
ptcAlarm | Integer |
ptcErrorStatus | Integer |
ptcOwnerString | OwnerString |
ptcEntryStatus | EntryStatus |
{ptcSpanEntry 1}
Description
Identifies an object in the programmable trunk card table. The object contains the physical location (hardware address) of the trunk card. This object lists the rack (R), level (L), and slot (S) where the card resides.
Object Identifier
1.3.6.1.4.1.886.1.4.1.1.1
Data Type
CardIndex
Access Policy
Read only
Status
Mandatory
{ptcSpanEntry 2}
Description
Specifies the type of programmable trunk card. The value in the card type object is a card attribute.
This object is the secondary index into the ptcTable.
Object Identifier
1.3.6.1.4.1.886.1.4.1.1.2
Data Type
Integer. The possible values and their names are shown in the following table:
| Value | Name |
|---|---|
1 | fourSpanT1 |
2 | fourSpanE1 |
3 | mvdcT1 |
Access Policy
Read only
Status
Mandatory
{ptcSpanEntry 3}
Description
Rack (R) where the card resides. The rack location is a card attribute.
Object Identifier
1.3.6.1.4.1.886.1.4.1.1.3
Data Type
Integer
Access Policy
Read only
Status
Mandatory
{ptcSpanEntry 4}
Description
Level (L) where the card resides. The level location is a card attribute.
Object Identifier
1.3.6.1.4.1.886.1.4.1.1.4
Data Type
Integer
Access Policy
Read only
Status
Mandatory
{ptcSpanEntry 5}
Description
Slot (S) where the card resides. The slot location is a card attribute.
Object Identifier
1.3.6.1.4.1.886.1.4.1.1.5
Data Type
Integer
Access Policy
Read only
Status
Mandatory
{ptcSpanEntry 6}
Description
Specifies the span number of the 4XT1, 4XE1, and MVDCT1 trunk cards.
Object Identifier
1.3.6.1.4.1.886.1.4.1.1.6
Data Type
Integer
Access Policy
Read only
Status
Mandatory
{ptcSpanEntry 7}
Description
Indicates the transmit gain control.
Object Identifier
1.3.6.1.4.1.886.1.4.1.1.7
Data Type
Integer. The valid numerical and string values are shown in the following table:
| Value | String |
|---|---|
1 | minus6db |
2 | minus3db |
3 | zerodb |
4 | plus3db |
5 | plus6db |
Access Policy
Read-write
Status
Mandatory
Default Value
zerodb
{ptcSpanEntry 8}
Description
Indicates the reference gain control.
Object Identifier
1.3.6.1.4.1.886.1.4.1.1.8
Data Type
Integer. The valid numerical and string values are shown in the following table:
| Value | String |
|---|---|
1 | minus6db |
2 | minus3db |
3 | zerodb |
4 | plus3db |
5 | plus6db |
Access Policy
Read-write
Status
Mandatory
Default Value
zerodb
{ptcSpanEntry 9}
Description
Indicates the transmit clock (timing source) for the T1, E1, and MVCDT1 span types.
Object Identifier
1.3.6.1.4.1.886.1.4.1.1.9
Data Type
Integer. The valid numerical and string values are shown in the following table:
| Value | String | Card Name | Meaning |
|---|---|---|---|
1 | sclk | T1,E1 | System clock |
2 | loop | T1,E1 | Incoming line |
3 | tx-1544 | T1 | Board crystal |
4 | tx-2048 | E1 | Board crystal |
Access Policy
Read-write
Status
Mandatory
{ptcSpanEntry 10}
Description
Indicates the reference clock (timing source). Applies only if this span is specified as the current timing source. Specify the source with one of the following methods:
When you choose a span as the master timing source, the reference clock for the span creates the system clock.
Object Identifier
1.3.6.1.4.1.886.1.4.1.1.10
Data Type
Integer. The possible values and their meanings are shown in the following table:
| Value | String | Card Name | Meaning |
|---|---|---|---|
1 | loop | T1, MVDCT1, E1 | Incoming line |
2 | rf-1544 | T1, MVDCT1 | Board crystal |
3 | rf-2048 | E1 | Board crystal |
Access Policy
Read-write
Status
Mandatory
{ptcSpanEntry 11}
Description
T1, MVDCT1—Indicates the format of the T1 stream. You can only change this value when the span status is Out-of-Service (OOS).
If you select an SF_NR or ESF_NR span type, the per port SIG TYPE field is ignored.
E1—Indicates the format of the E1 stream. You can only change this value when the span status is OOS. If you select CCS/31 format, the TS16 field is not accessible.
Object Identifier
1.3.6.1.4.1.886.1.4.1.1.11
Data Type
Integer. Possible values and their meanings are shown in the following table:
| Value | String | Card | Meaning |
|---|---|---|---|
1 | SF | T1, MVDCT1 | Superframe |
2 | ESF | T1, MVDCT1 | Extended superframe |
3 | SF-NR | T1, MVDCT1 | Superframe without robbed bit signaling |
4 | ESF-NR | T1, MVDCT1 | Extended superframe without robbed bit signaling |
5 | CAS/R2 | E1 | Channel associated signaling/R2 mode |
6 | CAS/MC | E1 | Channel associated signaling/Mercury Mode |
7 | CCS31B | E1 | Common channel signaling/31 bearer channels |
Access Policy
Read-write
Status
Mandatory
{ptcSpanEntry 12}
Description
Determines the number of transmit or receive slips the system detects for this span (in a 24-hour period) before threshold processing occurs. You can control this processing with the SLIP/OOF feature flag. Separate Slip maintenance counts are maintained for receive and transmit Slips. When either of these counters reaches the limit, threshold processing occurs. The current Slip count appears on the Diagnostic Card Display screen. Slip counters are reset at midnight or when you change this value.
Object Identifier
1.3.6.1.4.1.886.1.4.1.1.12
Data Type
Integer. Possible values are from 0 to 255. At zero (0), slip maintenance processing is inhibited. This setting is recommended when the TRX Clock = LOOP.
Access Policy
Read-write
Status
Mandatory
Default Value
255
{ptcSpanEntry 13}
Description
Determines the number of OOFs that the system detects for this span in a 24-hour period before threshold processing occurs. You control this processing with the SLIP/OOF feature flag. The OOF counter is reset at midnight or when you change this value.
Data Type
Integer. Possible values are from 0 to 255. Zero (0) is OOF maintenance processing inhibited (not recommended).
Object Identifier
1.3.6.1.4.1.886.1.4.1.1.13
Access Policy
Read-write
Status
Mandatory
Default Value
17
{ptcSpanEntry 14}
Description
Indicates the voice coding on the T1 or E1 stream. The system automatically turns off translation when calls specify unrestricted digital information bearer capability.
Object Identifier
1.3.6.1.4.1.886.1.4.1.1.14
Data Type
Integer. The valid numerical and string values are shown in the following table:
| Value | String | Meaning |
|---|---|---|
1 | a | Use A law for voice coding. |
2 | Mu | Use Mu law for voice coding. |
Access Policy
Read-write
Status
Mandatory
{ptcSpanEntry 15}
Description
T1, MVDCT1—Indicates the code on the T1 span.
E1—Indicates the code on the E1 span. The return value (2) should be interpreted depending on the card type.
Object Identifier
1.3.6.1.4.1.886.1.4.1.1.15
Data Type
Integer. The valid numerical and string values are shown in the following table:
| Value | String | Cards Supported |
|---|---|---|
1 | AMI | T1, MVDCT1, E1 |
2 | B8ZS | T1, MVDCT1 |
3 | B7ZSs | T1, MVDCT1 |
4 | HDB3 | E1 |
Access Policy
Read-write
Status
Mandatory
{ptcSpanEntry 16}
Description
Indicates the line equalization used for the T1/MVDCT1 stream.
Object Identifier
1.3.6.1.4.1.886.1.4.1.1.16
Data Type
Integer. The valid numerical and string values are shown in the following table:
| Value | String | Meaning |
|---|---|---|
0 | none | Used with 4XE1 card |
1 | leng0-133 | Length from 1 to 133 |
2 | leng133-266 | Length from 133 to 266 |
3 | leng266-399 | Length from 266 to 399 |
4 | leng399-533 | Length from 399 to 533 |
5 | leng533-655 | Length from 533 to 655 |
6 | lengPT-68-A | FCC Part 68 Option A |
7 | lengG-703 | ITU-T F.703 |
Access Policy
Read-write
Status
Mandatory
{ptcSpanEntry 17}
Description
Indicates if CRC checking is enabled.
Object Identifier
1.3.6.1.4.1.886.1.4.1.1.17
Data Type
Integer. The valid numerical and string values are shown in the following table:
| Value | String | Meaning |
|---|---|---|
0 | none | Invalid value. |
1 | crc-on | CRC checking is enabled. |
2 | crc-off | CRC checking is disabled. |
Access Policy
Read-write
Status
Mandatory
{ptcSpanEntry 18}
Description
Specifies international or national bits of Time Slot 0 as an 8-bit value.
Object Identifier
1.3.6.1.4.1.886.1.4.1.1.18
Data Type
Integer. The 8-bit value, i1Annnnn, has the following meaning:
i—International bits
A—A remote alarm indicator (the ITU-T default)
n—National bits
Access Policy
Read-write
Status
Mandatory
{ptcSpanEntry 19}
Description
Specifies extra bits and the C and D bits of Time Slot 16 as an 8-bit value. Use bits 3 and 4 to specify the C and D bits.
 |
Note For systems in China, the C and D bits must be set to 1. |
Object Identifier
1.3.6.1.4.1.886.1.4.1.1.19
Data Type
Integer. The valid numerical values are 0 to 255. The bit map, 0000xyxx, has the following meaning.
x = extra bits
y = a remote alarm indicator (the ITU-T default)
Access Policy
Read-write
Status
Mandatory
{ptcSpanEntry 20}
Description
Indicates the current status of the card.
Object Identifier
1.3.6.1.4.1.886.1.4.1.1.20
Data Type
Integer. Possible values and their meanings are shown in the following table:
| Value | String | Meaning |
|---|---|---|
1 | active | Ports on this card can be involved in active calls and can be allocated to new calls.1 |
2 | maintenance1 | One or more ports on this card might be involved in active calls. No ports are allocated to new calls.1 |
3 | diagnostics | No ports on this card are involved in calls or allocated to new calls. |
4 | outOfService | No ports on this card can be involved in active calls. No ports are allocated to new calls. |
7 | payload loopback | Diagnostic state. |
8 | remote loopback | Diagnostic state. |
| 1The agent might take as long as 10 seconds to set a card to Active. |
Access Policy
Read-write
Status
Mandatory
{ptcSpanEntry 21}
Description
Indicates the number of ports not currently active on this card. For multispan cards, this object indicates the number of ports not currently active on individual spans. Valid only for network interface and internal service circuit ports.
Object Identifier
1.3.6.1.4.1.886.1.4.1.1.21
Data Type
Integer
Access Policy
Read only
Status
Mandatory
{ptcSpanEntry 22}
Description
Indicates the version and the revision levels of the firmware installed on this card. Use this field to verify that the firmware versions you installed for all your network interface and service circuit cards are at the current level.
Object Identifier
1.3.6.1.4.1.886.1.4.1.1.22
Data Type
DisplayString. Length of the display string is from 1 to 5 characters.
Access Policy
Read only
Status
Mandatory
{ptcSpanEntry 23}
Description
The physical address of this card.
The value in this object is a span attribute.
Object Identifier
1.3.6.1.4.1.886.1.4.1.1.23
Data Type
Integer
Access Policy
Read only
Status
Mandatory
{ptcSpanEntry 24}
Description
A foreign key in the NFAS group table. This key indicates to which NFAS group this card belongs. To change this attribute, set the ptcEntryStatus and the nfasGroupTable objects to underModification (3).
Object Identifier
1.3.6.1.4.1.886.1.4.1.1.24
Data Type
Integer. The valid values are 0 to 37.
Access Policy
Read-write
Status
Mandatory
{ptcSpanEntry 25}
Description
Specifies the position of the span in the NFAS group.
Object Identifier
1.3.6.1.4.1.886.1.4.1.1.25
Data Type
Integer
Access Policy
Read only
Status
Mandatory
{ptcSpanEntry 26}
Description
Tracks which alarms are active on this span. Card alarms are internally represented as a bit map. A bit is set to 1 for each active card alarm. There are 32 bits. The following table shows the bits and the alarm description.
| Bit1 | Alarm Description |
|---|---|
0 | Card failure—minor |
1 | Port failure—minor |
2 | T1, E1, PRI carrier failure—major |
3 | T1, E1, PRI remote carrier failure—major |
4 | T1, E1, PRI card failure—major |
5 | T1, E1 Signaling Bit—minor |
6 | PRI Bipolar Violation MLimit reached—minor |
7 | T1, E1, PRI Out of Frame MLimit reached—minor |
8 | T1, E1 Slip Maint Limit reached—minor |
9 | T1, E1, PRI OOF condition—minor |
10 | PRI D-channel failure—major |
11-32 | Unsigned filler (set to zero) |
| 1The NMS application needs to interpret the alarm status from the integer value returned by this object. |
Object Identifier
1.3.6.1.4.1.886.1.4.1.1.26
Data Type
Integer
Access Policy
Read only
Status
Mandatory
{ptcSpanEntry 27}
Description
Registers the last error that occurred on this span entry. For a complete list of the card error messages, see "Card Error Messages".
Object Identifier
1.3.6.1.4.1.886.1.4.1.1.27
Data Type
Integer. The following table shows the values and their meanings:
| Value | Meaning |
|---|---|
4352 | frameTypeInvalid |
4353 | codeInvalid |
4354 | txInvalid |
4355 | rxInvalid |
4356 | txClockInvalid |
4357 | refClockInvalid |
4358 | oofSlipInvalid |
4359 | lawInvalid |
4360 | spanLengthInvalid |
4361 | crcInvalid |
4362 | ts0Invalid |
4363 | ts16Invalid |
4364 | mustBeOos |
Access Policy
Read only
Status
Mandatory
{ptcSpanEntry 28}
Description
The entity that configured this object and is therefore using the resources assigned to it.
Object Identifier
1.3.6.1.4.1.886.1.4.1.1.28
Data Type
OwnerString
Access Policy
Read-write
Status
Mandatory
{ptcSpanEntry 29}
Description
Status of the programmable trunk card object. Use this object to add or delete a programmable card and to modify span attributes. A createRequest command on any span creates the entire card (all spans). Set each individual span to valid (1) once all modifications are done. When you set any one span to invalid (4), the entire card is deleted.
Object Identifier
1.3.6.1.4.1.886.1.4.1.1.29
Data Type
EntryStatus
Access Policy
Read-write
Status
Mandatory
{ptcSpanEntry 30}
Description
Version/revision of the card download file.
Object Identifier
1.3.6.1.4.1.886.1.4.1.1.30
Data Type
DisplayString (size 1...4)
Access Policy
Read only
Status
Mandatory
{ptcSpanEntry 31}
Description
The upgrade state of this trunk card entry.
Object Identifier
1.3.6.1.4.1.886.1.4.1.1.31
Data Type
UpgradeState
Access Policy
Read only
Status
Mandatory
{ptc 2}
Description
The time, displayed in hundredths of a second, since the ptcSpanTable was last modified. Helps NMS application developers determine the polling of the agent parameters.
Object Identifier
1.3.6.1.4.1.886.1.4.2
Data Type
TimeTicks
Access Policy
Read only
Status
Mandatory
This section contains the objects for configuring the Programmable T1 and E1 ports.
{ptc 4}
Description
Lists port entries on each programmable card.
Object Identifier
1.3.6.1.4.1.886.1.4.4
Data Type
Sequence of ProgPortEntry
Access Policy
Not accessible
Status
Mandatory
{progPortTable 1}
Description
Table containing objects belonging to a particular port.
Object Identifier
1.3.6.1.4.1.886.1.4.4.1
Data Type
ProgPortEntry
Access Policy
Not accessible
Status
Mandatory
Index
{ptcIndex, ptcSpanNum, progPortIndex}
Sequence
progPortIndex | Integer |
progPortName | DisplayString |
progSigType | Integer |
progCos | Integer |
progWinkMin | Integer |
progWinkMax | Integer |
progWinkSend | Integer |
progFlashMin | Integer |
progFlashMax | Integer |
progFlashSend | Integer |
progOffHk | Integer |
progGuard | Integer |
progPortMajorState | PortMajorState |
progPortSuppState | PortSuppState |
progPortAddress | Integer |
progInpulseRuleIndex | Integer |
progResGroupIndex | Integer |
progResGroupPosition | Integer |
progPortErrorStatus | Integer |
progPortOwnerString | OwnerString |
progPortEntryStatus | PortEntryStatus |
progPortState | Integer |
progPCardType | Integer |
{progPortEntry 1}
Description
Indicates the port number on the span. There are 24 ports on a progT1 span and 32 ports on a progE1 span.
Object Identifier
1.3.6.1.4.1.886.1.4.4.1.1
Data Type
Integer. The number of the port. Possible values are from 1 to 24 for T1 and MVDCT1 and 1 to 32 for E1.
Access Policy
Read only
Status
Mandatory
{progPortEntry 2}
Description
Identifies individual circuits (optional). Each name should be unique and helpful in describing for what you use the port.
Object Identifier
1.3.6.1.4.1.886.1.4.4.1.2
Data Type
DisplayString. This field accepts up to 8 upper- or lowercase alphanumeric characters.
Access Policy
Read-write
Status
Mandatory
{progPortEntry 3}
Description
Determines the signaling type. If you select an SF_NR or ESF_NR span type, the per port SigType field is ignored.
Object Identifier
1.3.6.1.4.1.886.1.4.4.1.3
Data Type
Integer. The valid numerical and string values are shown in the following table:
| Value | String | Meaning |
|---|---|---|
1 | eAndm | E and M |
2 | fxo-ls | Foreign Exchange Office—Loop Start |
3 | fxo-gs | Foreign Exchange Office—Ground Start |
4 | fxs-ls | Foreign Exchange Subscriber—Loop Start |
5 | fxs-gs | Foreign Exchange Subscriber—Ground Start |
6 | clear |
|
Access Policy
Read-write
Status
Mandatory
{progPortEntry 4}
Description
Used for resource grouping and B-channel allocation and determining the values of the software operating characteristics for this port. Different spans on the same card can have different COS marks.
Object Identifier
1.3.6.1.4.1.886.1.4.4.1.4
Data Type
Integer. Possible values and their meanings are shown in the following table:
| Value | String | Meaning |
|---|---|---|
0 | none | No port COS value. |
1 | o | Originating—Calls originating from the system. Outgoing calls initiated by the host command. |
2 | t | Terminating—Calls terminating at the system. Incoming calls initiated by action outside the system or forced by the host command. |
3 | w2 | Two-Way—Calls originating from the system or calls terminating at the system. Outgoing calls initiated by the host command. Incoming calls initiated by outside actions. |
4 | oa | Always Off Hook and Originating—Calls originating from the system. Port goes off hook at system reset and remains off hook. Outgoing calls initiated by the host command. |
5 | ta | Always Off Hook and Terminating—Calls terminating at the system. Port goes off hook at system reset and remains off hook. Incoming calls initiated by outside actions or forced by the host command. |
6 | a2 | Always Off Hook and Two-Way—Calls originating from the system or calls terminating at the system. Port goes off hook at system reset and remains off hook. Outgoing calls initiated by the host command, incoming calls initiated by outside actions or forced by the host command. |
Access Policy
Read-write
Status
Mandatory
{progPortEntry 5}
Description
Indicates the minimum wink detect time. For E1, this is the time to wait for the delayed dial signal.
Object Identifier
1.3.6.1.4.1.886.1.4.4.1.5
Data Type
Integer. The valid values are from 0 to 255.
Access Policy
Read-write
Status
Mandatory
{progPortEntry 6}
Description
Indicates the maximum wink detect time. Not used for E1 boards.
Data Type
Integer. The valid values are from 0 to 255.
Object Identifier
1.3.6.1.4.1.886.1.4.4.1.6
Access Policy
Read-write
Status
Mandatory
{progPortEntry 7}
Description
Indicates the wink send time. For the E1 card, this is the time period of the delayed dial signal.
Object Identifier
1.3.6.1.4.1.886.1.4.4.1.7
Data Type
Integer. The valid values are from 0 to 255.
Access Policy
Read-write
Status
Mandatory
{progPortEntry 8}
Description
Indicates the minimum flash detect time.
Object Identifier
1.3.6.1.4.1.886.1.4.4.1.8
Data Type
Integer. The valid values are from 0 to 255.
Access Policy
Read-write
Status
Mandatory
{progPortEntry 9}
Description
Indicates the maximum flash detect time.
Object Identifier
1.3.6.1.4.1.886.1.4.4.1.9
Data Type
Integer. The valid values are from 0 to 255.
Access Policy
Read-write
Status
Mandatory
{progPortEntry 10}
Description
Indicates the flash send time.
Object Identifier
1.3.6.1.4.1.886.1.4.4.1.10
Data Type
Integer. The valid values are from 0 to 255.
Access Policy
Read-write
Status
Mandatory
{progPortEntry 11}
Description
Indicates the minimum off-hook time.
Object Identifier
1.3.6.1.4.1.886.1.4.4.1.11
Data Type
Integer. The valid values are from 0 to 255.
Access Policy
Read-write
Status
Mandatory
{progPortEntry 12}
Description
Indicates the guard time.
Object Identifier
1.3.6.1.4.1.886.1.4.4.1.12
Data Type
Integer. The valid values are from 0 to 255.
Access Policy
Read-write
Status
Mandatory
{progPortEntry 13}
Description
The major state of the port.
Object Identifier
1.3.6.1.4.1.886.1.4.4.1.13
Data Type
PortMajorState
Access Policy
Read only
Status
Mandatory
{progPortEntry 14}
Description
The supplementary state of the port.
Object Identifier
1.3.6.1.4.1.886.1.4.4.1.14
Data Type
PortSuppState
Access Policy
Read only
Status
Mandatory
{progPortEntry 15}
Description
Specifies the software address (hexadecimal identifier) of the port for which data is displayed. The port can also be specified by the hardware address.
Object Identifier
1.3.6.1.4.1.886.1.4.4.1.15
Data Type
Integer
Access Policy
Read only
Status
Mandatory
{progPortEntry 16}
Description
A foreign key corresponding to the inpulseRuleIndex in the inpulseTable. You access this object when you assign a particular inpulse rule to a port.
Determines the inpulse rule processed when this port goes off hook. Default inpulse rules are used for incoming ports only. Class of Service = T, W2, AT, or A2. The inpulse rule must be defined from the Inpulse Rules Table screens.
Object Identifier
1.3.6.1.4.1.886.1.4.4.1.16
Data Type
Integer. Possible values are from 0 to 30 in 2K mode, or 0 to 255 in 4K mode. Zero means you are not selecting a default inpulse rule.
Access Policy
Read-write
Status
Mandatory
{progPortEntry 17}
Description
A foreign key corresponding to the groupIndex in the resGroupTable that indicates the number of the resource group to which this port belongs. If you do not make a resource group assignment, this object is zero (0). To change this attribute, set the progPortEntryStatus and the resGroupTable objects to underModification (3).
Object Identifier
1.3.6.1.4.1.886.1.4.4.1.17
Data Type
Integer. Possible values range from 0 to 63 in 2K mode, or 0 to 224 in 4K mode.
Access Policy
Read-write
Status
Mandatory
{progPortEntry 18}
Description
Specifies the position of the port in the assigned resource group.
Object Identifier
1.3.6.1.4.1.886.1.4.4.1.18
Data Type
Integer
Access Policy
Read only
Status
Mandatory
{progPortEntry 19}
Description
Registers the last error that occurred on this port object.
Object Identifier
1.3.6.1.4.1.886.1.4.4.1.19
Data Type
Integer
Access Policy
Read only
Status
Mandatory
{progPortEntry 20}
Description
The entity that configured this object and is therefore using the assigned resources.
Object Identifier
1.3.6.1.4.1.886.1.4.4.1.20
Data Type
OwnerString
Access Policy
Read-write
Status
Mandatory
{progPortEntry 21}
Description
Status of this table object.
Object Identifier
1.3.6.1.4.1.886.1.4.4.1.21
Data Type
PortEntryStatus
Access Policy
Read-write
Status
Mandatory
{progPortEntry 22}
Description
Contains the state of the port where active is 1 and inactive is 2.
|
Note Always modify the state of ports one at a time. That is, the EntryStatus object must be set to valid after every SNMP_SET command on this object. |
Object Identifier
1.3.6.1.4.1.886.1.4.4.1.22
Data Type
Integer. The valid values are 1 (active) and 2 (inactive).
Access Policy
Read-write
Status
Mandatory
{progPortEntry 23}
Description
Specifies the type of programmable trunk card to which this port belongs.
Object Identifier
1.3.6.1.4.1.886.1.4.4.1.23
Data Type
Integer. The following table lists the values and their meanings:
| Value | Meaning |
|---|---|
1 | fourSpanT1 |
2 | fourSpanE1 |
3 | mvdcT1 |
Access Level
Read only
Status
Mandatory
{ptc 5}
Description
The time, displayed in hundredths of a second, since the port table (progPortTable) was last modified. Helps NMS application developers determine the polling of the agent parameters.
Object Identifier
1.3.6.1.4.1.886.1.4.5
Data Type
TimeTicks
Access Policy
Read only
Status
Mandatory
Posted: Sat Sep 28 11:08:38 PDT 2002
All contents are Copyright © 1992--2002 Cisco Systems, Inc. All rights reserved.
Important Notices and Privacy Statement.