home | O'Reilly's CD bookshelfs | FreeBSD | Linux | Cisco | Cisco Exam  


sed & awk

sed & awkSearch this book
Previous: 4.1 Applying Commands in a Script Chapter 4
Writing sed Scripts
Next: 4.3 Testing and Saving Output
 

4.2 A Global Perspective on Addressing

One of the first things you'll notice about sed commands is that sed will apply them to every input line. Sed is implicitly global, unlike ed , ex , or vi . The following substitute command will change every "CA" into "California."

s/CA/California/g

If the same command were entered from the ex command prompt in vi , it would make the replacement for all occurrences on the current line only. In sed, it is as though each line has a turn at becoming the current line and so the command is applied to every line. Line addresses are used to supply context for, or restrict , an operation. (In short: Nothing gets done in vi unless you tell it which lines to work on, while sed will work on every line unless you tell it not to.) For instance, by supplying the address "Sebastopol" to the previous substitute command, we can limit the replacement of "CA" by "California" to just lines containing "Sebastopol."

/Sebastopol/s/CA/California/g

An input line consisting of "Sebastopol, CA" would match the address and the substitute command would be applied, changing it to "Sebastopol, California." A line consisting of "San Francisco, CA" would not be matched and the substitution would not be applied.

A sed command can specify zero, one, or two addresses. An address can be a regular expression describing a pattern, a line number, or a line addressing symbol.

  • If no address is specified, then the command is applied to each line.

  • If there is only one address, the command is applied to any line matching the address.

  • If two comma-separated addresses are specified, the command is performed on the first line matching the first address and all succeeding lines up to and including a line matching the second address.

  • If an address is followed by an exclamation mark (! ), the command is applied to all lines that do not match the address.

To illustrate how addressing works, let's look at examples using the delete command, d . A script consisting of simply the d command and no address produces no output since it deletes all lines:

d

When a line number is supplied as an address, the command affects only that line. For instance, the following example deletes only the first line:

1d

The line number refers to an internal line count maintained by sed. This counter is not reset for multiple input files. Thus, no matter how many files were specified as input, there is only one line 1 in the input stream.

Similarly, the input stream has only one last line. It can be specified using the addressing symbol $ . The following example deletes the last line of input:

$d

The $ symbol should not be confused with the $ used in regular expressions, which means the end of the line.

When a regular expression is supplied as an address, the command affects only the lines matching that pattern. The regular expression must be enclosed by slashes (/). The following delete command

/^$/d

deletes only blank lines. All other lines are passed through untouched.

If you supply two addresses, then you specify a range of lines over which the command is executed. The following example shows hows to delete all lines blocked by a pair of macros, in this case, .TS and .TE, that mark tbl input.

/^\.TS/,/^\.TE/d

It deletes all lines beginning with the line matched by the first pattern and up to and including the line matched by the second pattern. Lines outside this range are not affected. The following command deletes from line 50 to the last line in the file:

50,$d

You can mix a line address and a pattern address:

1,/^$/d

This example deletes from the first line up to the first blank line, which, for instance, will delete a mailer header from an Internet mail message that you have saved in a file.

You can think of the first address as enabling the action and the second address as disabling it. Sed has no way of looking ahead to determine if the second match will be made. The action will be applied to lines once the first match is made. The command will be applied to all subsequent lines until the second match is made. In the previous example, if the file did not contain a blank line, then all lines would be deleted.

An exclamation mark (!) following an address reverses the sense of the match. For instance, the following script deletes all lines except those inside tbl input:

/^\.TS/,/^\.TE/!d

This script, in effect, extracts tbl input from a source file.

4.2.1 Grouping Commands

Braces ({}) are used in sed to nest one address inside another or to apply multiple commands at the same address. You can nest addresses if you want to specify a range of lines and then, within that range, specify another address. For example, to delete blank lines only inside blocks of tbl input, use the following command:

/^\.TS/,/^\.TE/{
      /^$/d
}

The opening curly brace must end a line and the closing curly brace must be on a line by itself. Be sure there are no spaces after the braces.

You can apply multiple commands to the same range of lines by enclosing the editing commands within braces, as shown below.

/^\.TS/,/^\.TE/{
	/^$/d
  	s/^\.ps 10/.ps 8/
  	s/^\.vs 12/.vs 10/
}

This example not only deletes blank lines in tbl input but it also uses the substitute command, s , to change several troff requests. These commands are applied only to lines within the .TS/.TE block.


Previous: 4.1 Applying Commands in a Script sed & awk Next: 4.3 Testing and Saving Output
4.1 Applying Commands in a Script Book Index 4.3 Testing and Saving Output

The UNIX CD Bookshelf NavigationThe UNIX CD BookshelfUNIX Power ToolsUNIX in a NutshellLearning the vi Editorsed & awkLearning the Korn ShellLearning the UNIX Operating System