Jump to content United States-English
HP.com Home Products and Services Support and Drivers Solutions How to Buy
» Contact HP
More options
HP.com home
HP-UX Virtual Partitions Administrator’s Guide > Chapter 8 CPU, Memory, and I/O Resources (A.03.xx)

I/O: Allocation Notes

» 

Technical documentation

Complete book in PDF
» Feedback
Content starts here

 » Table of Contents

 » Glossary

 » Index

When planning or performing I/O allocation, note the following:

  • An LBA can be assigned to at most one virtual partition at any given time.  When you are planning your I/O to virtual partition assignments, note that only one virtual partition may own any hardware at or below the LBA (Local Bus Adapter) level. In other words, hardware at or below the LBA level must be in the same virtual partition.

    Example  Looking at the ioscan output of a rp7400/N4000, the two internal disk slots use the same LBA:

    0/0 ba Local PCI Bus Adapter (782) 0/0/2/0 ext_bus SCSI C875 Ultra Wide Single-Ended 0/0/2/1 ext_bus SCSI C875 Ultra Wide Single-Ended

    Therefore, you cannot assign one of the internal disks to partition vpar1 and the other internal disk to partition vpar2; these disks must reside in the same partition.

  • Syntax Notes  

    CAUTION: Using vPars A.03.01 or earlier, LBAs must be explicitly specified (included in the hardware path). Specifying only the SBA is not supported. If specifying only an SBA, the commands will not assume that all LBAs under the SBA are to be assigned; the system may actually panic.
    Beginning with vPars A.03.02, you can specify only the SBA. The vPars commands will assume the change applies to all LBAs under the specified SBA.

    The exception are boot disks; boot disks are specified using the full hardware path.

    NOTE: When assigning I/O, if you specify a path below the LBA level (for example, cell/sba/lba/.../device, vPars automatically assign the LBA to the virtual partition. For example, if you specify -a io:0/0/0/2/0.6.0 where 0/0/0 is the cell/sba/lba, the lba of 0/0/0 is assigned to the virtual partition. Further, this LBA assignment implies that all devices using 0/0/0 are assigned to the virtual partition.

    The assignment rules of LBAs remain applicable: the LBA can only be owned by one virtual partition. For example, once the LBA at 0/0/0 is assigned to one virtual partition, it cannot be simultaneously assigned to any other virtual partition. Thus, if the device at 0/0/0/2/0.6.0 is assigned to a virtual partition, the LBA at 0/0/0 is assigned to that virtual partition, so the device at 0/0/0/2/0.6.0 cannot be assigned to a different virtual partition.

    LBA Example

    The vparcreate command on a non-nPartitionable system looks like:

    #vparcreate -p vpar1 -a cpu::1 -a cpu:::1 -a mem::1024 -a io:0.0 -a io:0.0.2.0.6.0:BOOT

    where the I/O assignment is specified using the LBA level (-a io:0.0) and the boot disk is specified using the full hardware path (-a io:0.0.2.0.6.0).

    For an nPartitionable system, the vparcreate command would look like:

    # vparcreate -p vpar1 -a cpu::1 -a cpu:::1 -a mem::1024 -a io:0.0.0 \ -a io:0.0.0.2.0.6.0:BOOT

    where the I/O assignment is specified using the LBA level (-a io:0.0.0.) and the boot disk is specified using the full hardware path (-a io:0.0.0.2.0.6.0).

    For information on using the LBA level on nPartitionable systems, also see “Planning, Installing, and Using vPars with an nPartitionable Server”.

  • SBA/LBA versus cell/SBA/LBA  When viewing hardware paths, note the following:

    1. The explicit specification of an LBA on a non-nPartitionable system consists of two fields: sba/lba

    2. The explicit specification of an LBA on an nPartitionable system consists of three fields: cell/sba/lba

    3. With A.03.02 and later and A.04.xx, all LBAs under a SBA are implied when explicitly specifying a SBA without specifying any LBA. Therefore, the path specified on a command line can have different meanings depending upon the vPars version, the type of server, and the user intent. For example, the path of x/y can mean any of the following:

      • sba=x, lba=y on a non-nPartitionable server running vPars A.03.01 or earlier.

      • sba=x, lba=y on a non-nPartitionable server running vPars A.03.02 or later or A.04.xx.

      • cell=x, sba=y on an nPartitionable server running vPars A.03.02 or later or A.04.xx.

  • Supported I/O  Check your hardware manual to verify that your mass storage unit can be used as a bootable device. If a mass storage unit cannot be used as a boot disk on a non-vPars server, it cannot be used as a boot disk on a vPars server. vPars does not add any additional capability to the hardware.

    For information on supported I/O interface cards and configurations, see the document HP-UX Virtual Partitions Ordering and Configuration Guide.

Printable version
Privacy statement Using this site means you accept its terms Feedback to webmaster
© 2008 Hewlett-Packard Development Company, L.P.